mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 20:53:53 +08:00
7e9d109858
Add Tegra210 support for DFLL clock. Cc: devicetree@vger.kernel.org Signed-off-by: Joseph Lo <josephl@nvidia.com> Acked-by: Jon Hunter <jonathanh@nvidia.com> Acked-by: Stephen Boyd <sboyd@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Thierry Reding <treding@nvidia.com>
156 lines
6.2 KiB
Plaintext
156 lines
6.2 KiB
Plaintext
NVIDIA Tegra124 DFLL FCPU clocksource
|
|
|
|
This binding uses the common clock binding:
|
|
Documentation/devicetree/bindings/clock/clock-bindings.txt
|
|
|
|
The DFLL IP block on Tegra is a root clocksource designed for clocking
|
|
the fast CPU cluster. It consists of a free-running voltage controlled
|
|
oscillator connected to the CPU voltage rail (VDD_CPU), and a closed loop
|
|
control module that will automatically adjust the VDD_CPU voltage by
|
|
communicating with an off-chip PMIC either via an I2C bus or via PWM signals.
|
|
|
|
Required properties:
|
|
- compatible : should be one of:
|
|
- "nvidia,tegra124-dfll": for Tegra124
|
|
- "nvidia,tegra210-dfll": for Tegra210
|
|
- reg : Defines the following set of registers, in the order listed:
|
|
- registers for the DFLL control logic.
|
|
- registers for the I2C output logic.
|
|
- registers for the integrated I2C master controller.
|
|
- look-up table RAM for voltage register values.
|
|
- interrupts: Should contain the DFLL block interrupt.
|
|
- clocks: Must contain an entry for each entry in clock-names.
|
|
See clock-bindings.txt for details.
|
|
- clock-names: Must include the following entries:
|
|
- soc: Clock source for the DFLL control logic.
|
|
- ref: The closed loop reference clock
|
|
- i2c: Clock source for the integrated I2C master.
|
|
- resets: Must contain an entry for each entry in reset-names.
|
|
See ../reset/reset.txt for details.
|
|
- reset-names: Must include the following entries:
|
|
- dvco: Reset control for the DFLL DVCO.
|
|
- #clock-cells: Must be 0.
|
|
- clock-output-names: Name of the clock output.
|
|
- vdd-cpu-supply: Regulator for the CPU voltage rail that the DFLL
|
|
hardware will start controlling. The regulator will be queried for
|
|
the I2C register, control values and supported voltages.
|
|
|
|
Required properties for the control loop parameters:
|
|
- nvidia,sample-rate: Sample rate of the DFLL control loop.
|
|
- nvidia,droop-ctrl: See the register CL_DVFS_DROOP_CTRL in the TRM.
|
|
- nvidia,force-mode: See the field DFLL_PARAMS_FORCE_MODE in the TRM.
|
|
- nvidia,cf: Numeric value, see the field DFLL_PARAMS_CF_PARAM in the TRM.
|
|
- nvidia,ci: Numeric value, see the field DFLL_PARAMS_CI_PARAM in the TRM.
|
|
- nvidia,cg: Numeric value, see the field DFLL_PARAMS_CG_PARAM in the TRM.
|
|
|
|
Optional properties for the control loop parameters:
|
|
- nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
|
|
|
|
Optional properties for mode selection:
|
|
- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C.
|
|
|
|
Required properties for I2C mode:
|
|
- nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
|
|
|
|
Required properties for PWM mode:
|
|
- nvidia,pwm-period-nanoseconds: period of PWM square wave in nanoseconds.
|
|
- nvidia,pwm-tristate-microvolts: Regulator voltage in micro volts when PWM
|
|
control is disabled and the PWM output is tristated. Note that this voltage is
|
|
configured in hardware, typically via a resistor divider.
|
|
- nvidia,pwm-min-microvolts: Regulator voltage in micro volts when PWM control
|
|
is enabled and PWM output is low. Hence, this is the minimum output voltage
|
|
that the regulator supports when PWM control is enabled.
|
|
- nvidia,pwm-voltage-step-microvolts: Voltage increase in micro volts
|
|
corresponding to a 1/33th increase in duty cycle. Eg the voltage for 2/33th
|
|
duty cycle would be: nvidia,pwm-min-microvolts +
|
|
nvidia,pwm-voltage-step-microvolts * 2.
|
|
- pinctrl-0: I/O pad configuration when PWM control is enabled.
|
|
- pinctrl-1: I/O pad configuration when PWM control is disabled.
|
|
- pinctrl-names: must include the following entries:
|
|
- dvfs_pwm_enable: I/O pad configuration when PWM control is enabled.
|
|
- dvfs_pwm_disable: I/O pad configuration when PWM control is disabled.
|
|
|
|
Example for I2C:
|
|
|
|
clock@70110000 {
|
|
compatible = "nvidia,tegra124-dfll";
|
|
reg = <0 0x70110000 0 0x100>, /* DFLL control */
|
|
<0 0x70110000 0 0x100>, /* I2C output control */
|
|
<0 0x70110100 0 0x100>, /* Integrated I2C controller */
|
|
<0 0x70110200 0 0x100>; /* Look-up table RAM */
|
|
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&tegra_car TEGRA124_CLK_DFLL_SOC>,
|
|
<&tegra_car TEGRA124_CLK_DFLL_REF>,
|
|
<&tegra_car TEGRA124_CLK_I2C5>;
|
|
clock-names = "soc", "ref", "i2c";
|
|
resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
|
|
reset-names = "dvco";
|
|
#clock-cells = <0>;
|
|
clock-output-names = "dfllCPU_out";
|
|
vdd-cpu-supply = <&vdd_cpu>;
|
|
|
|
nvidia,sample-rate = <12500>;
|
|
nvidia,droop-ctrl = <0x00000f00>;
|
|
nvidia,force-mode = <1>;
|
|
nvidia,cf = <10>;
|
|
nvidia,ci = <0>;
|
|
nvidia,cg = <2>;
|
|
|
|
nvidia,i2c-fs-rate = <400000>;
|
|
};
|
|
|
|
Example for PWM:
|
|
|
|
clock@70110000 {
|
|
compatible = "nvidia,tegra124-dfll";
|
|
reg = <0 0x70110000 0 0x100>, /* DFLL control */
|
|
<0 0x70110000 0 0x100>, /* I2C output control */
|
|
<0 0x70110100 0 0x100>, /* Integrated I2C controller */
|
|
<0 0x70110200 0 0x100>; /* Look-up table RAM */
|
|
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>,
|
|
<&tegra_car TEGRA210_CLK_DFLL_REF>,
|
|
<&tegra_car TEGRA124_CLK_I2C5>;;
|
|
clock-names = "soc", "ref", "i2c";
|
|
resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
|
|
reset-names = "dvco";
|
|
#clock-cells = <0>;
|
|
clock-output-names = "dfllCPU_out";
|
|
|
|
nvidia,sample-rate = <25000>;
|
|
nvidia,droop-ctrl = <0x00000f00>;
|
|
nvidia,force-mode = <1>;
|
|
nvidia,cf = <6>;
|
|
nvidia,ci = <0>;
|
|
nvidia,cg = <2>;
|
|
|
|
nvidia,pwm-min-microvolts = <708000>; /* 708mV */
|
|
nvidia,pwm-period-nanoseconds = <2500>; /* 2.5us */
|
|
nvidia,pwm-to-pmic;
|
|
nvidia,pwm-tristate-microvolts = <1000000>;
|
|
nvidia,pwm-voltage-step-microvolts = <19200>; /* 19.2mV */
|
|
|
|
pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable";
|
|
pinctrl-0 = <&dvfs_pwm_active_state>;
|
|
pinctrl-1 = <&dvfs_pwm_inactive_state>;
|
|
};
|
|
|
|
/* pinmux nodes added for completeness. Binding doc can be found in:
|
|
* Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
|
|
*/
|
|
|
|
pinmux: pinmux@700008d4 {
|
|
dvfs_pwm_active_state: dvfs_pwm_active {
|
|
dvfs_pwm_pbb1 {
|
|
nvidia,pins = "dvfs_pwm_pbb1";
|
|
nvidia,tristate = <TEGRA_PIN_DISABLE>;
|
|
};
|
|
};
|
|
dvfs_pwm_inactive_state: dvfs_pwm_inactive {
|
|
dvfs_pwm_pbb1 {
|
|
nvidia,pins = "dvfs_pwm_pbb1";
|
|
nvidia,tristate = <TEGRA_PIN_ENABLE>;
|
|
};
|
|
};
|
|
};
|