mirror of
https://github.com/edk2-porting/linux-next.git
synced 2024-12-23 20:53:53 +08:00
68a15eb7bd
This PCI host bridge from V3 Semiconductor needs no further introduction. An ancient driver for it has been sitting in arch/arm/mach-integrator/pci_v3.* since before v2.6.12 and the initial migration to git. But we need to get the drivers out of arch/arm/* and get proper handling of the old drivers, rewrite and clean up so the PCI maintainer can control the mass of drivers without having to run all over the kernel. We also switch swiftly to all the new infrastructure found in the PCI hosts as of late. Some code is preserved so I have added an extensive list of authors in the top comment section. This driver probes with the following result: OF: PCI: host bridge /pciv3@62000000 ranges: OF: PCI: No bus range found for /pciv3@62000000, using [bus 00-ff] OF: PCI: IO 0x60000000..0x6000ffff -> 0x00000000 OF: PCI: MEM 0x40000000..0x4fffffff -> 0x40000000 OF: PCI: MEM 0x50000000..0x5fffffff -> 0x50000000 pci-v3-semi 62000000.pciv3: initialized PCI V3 Integrator/AP integration pci-v3-semi 62000000.pciv3: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [bus 00-ff] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff] pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff pref] pci-v3-semi 62000000.pciv3: parity error interrupt pci-v3-semi 62000000.pciv3: master abort error interrupt pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt pci-v3-semi 62000000.pciv3: master abort error interrupt (repeats a few times) pci 0000:00:09.0: [1011:0024] type 01 class 0x060400 pci-v3-semi 62000000.pciv3: master abort error interrupt pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt pci 0000:00:0b.0: [8086:1229] type 00 class 0x020000 pci 0000:00:0b.0: reg 0x10: [mem 0x00000000-0x00000fff pref] pci 0000:00:0b.0: reg 0x14: [io 0x0000-0x001f] pci 0000:00:0b.0: reg 0x18: [mem 0x00000000-0x000fffff] pci 0000:00:0b.0: reg 0x30: [mem 0x00000000-0x000fffff pref] pci 0000:00:0b.0: supports D1 D2 pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot pci 0000:00:0c.0: [5333:8811] type 00 class 0x030000 pci 0000:00:0c.0: reg 0x10: [mem 0x00000000-0x03ffffff] pci 0000:00:0c.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] pci 0000:00:0c.0: vgaarb: VGA device added: decodes=io+mem,owns=io,locks=none PCI: bus0: Fast back to back transfers disabled PCI: bus1: Fast back to back transfers enabled pci 0000:00:0c.0: BAR 0: assigned [mem 0x40000000-0x43ffffff] pci 0000:00:0b.0: BAR 2: assigned [mem 0x44000000-0x440fffff] pci 0000:00:0b.0: BAR 6: assigned [mem 0x50000000-0x500fffff pref] pci 0000:00:0c.0: BAR 6: assigned [mem 0x50100000-0x5010ffff pref] pci 0000:00:0b.0: BAR 0: assigned [mem 0x50110000-0x50110fff pref] pci 0000:00:0b.0: BAR 1: assigned [io 0x1000-0x101f] pci 0000:00:09.0: PCI bridge to [bus 01] pci 0000:00:0b.0: Firmware left e100 interrupts enabled; disabling (...) e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI e100: Copyright(c) 1999-2006 Intel Corporation e100 0000:00:0b.0: enabling device (0146 -> 0147) e100 0000:00:0b.0 eth0: addr 0x50110000, irq 31, MAC addr 00:08:c7:99:d2:57 > lspci 00:0b.0 Class 0200: 8086:1229 00:09.0 Class 0604: 1011:0024 00:0c.0 Class 0300: 5333:8811 > cat /proc/iomem 40000000-4fffffff : V3 PCI NON-PRE-MEM 40000000-43ffffff : 0000:00:0c.0 44000000-440fffff : 0000:00:0b.0 44000000-440fffff : e100 50000000-5fffffff : V3 PCI PRE-MEM 50000000-500fffff : 0000:00:0b.0 50100000-5010ffff : 0000:00:0c.0 50110000-50110fff : 0000:00:0b.0 50110000-50110fff : e100 61000000-61ffffff : /pciv3@62000000 62000000-6200ffff : /pciv3@62000000 Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [bhelgaas: fold in %pR fixes from Arnd Bergmann <arnd@arndb.de>: http://lkml.kernel.org/r/20171011140224.3770968-1-arnd@arndb.de] Signed-off-by: Bjorn Helgaas <bhelgaas@google.com> CC: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
230 lines
6.5 KiB
Plaintext
230 lines
6.5 KiB
Plaintext
menu "PCI host controller drivers"
|
|
depends on PCI
|
|
|
|
config PCI_MVEBU
|
|
bool "Marvell EBU PCIe controller"
|
|
depends on ARCH_MVEBU || ARCH_DOVE
|
|
depends on ARM
|
|
depends on OF
|
|
|
|
config PCI_AARDVARK
|
|
bool "Aardvark PCIe controller"
|
|
depends on ARCH_MVEBU && ARM64
|
|
depends on OF
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
help
|
|
Add support for Aardvark 64bit PCIe Host Controller. This
|
|
controller is part of the South Bridge of the Marvel Armada
|
|
3700 SoC.
|
|
|
|
config PCIE_XILINX_NWL
|
|
bool "NWL PCIe Core"
|
|
depends on ARCH_ZYNQMP
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
help
|
|
Say 'Y' here if you want kernel support for Xilinx
|
|
NWL PCIe controller. The controller can act as Root Port
|
|
or End Point. The current option selection will only
|
|
support root port enabling.
|
|
|
|
config PCI_FTPCI100
|
|
bool "Faraday Technology FTPCI100 PCI controller"
|
|
depends on OF
|
|
depends on ARM
|
|
default ARCH_GEMINI
|
|
|
|
config PCI_TEGRA
|
|
bool "NVIDIA Tegra PCIe controller"
|
|
depends on ARCH_TEGRA
|
|
help
|
|
Say Y here if you want support for the PCIe host controller found
|
|
on NVIDIA Tegra SoCs.
|
|
|
|
config PCI_RCAR_GEN2
|
|
bool "Renesas R-Car Gen2 Internal PCI controller"
|
|
depends on ARM
|
|
depends on ARCH_RENESAS || COMPILE_TEST
|
|
help
|
|
Say Y here if you want internal PCI support on R-Car Gen2 SoC.
|
|
There are 3 internal PCI controllers available with a single
|
|
built-in EHCI/OHCI host controller present on each one.
|
|
|
|
config PCIE_RCAR
|
|
bool "Renesas R-Car PCIe controller"
|
|
depends on ARCH_RENESAS || (ARM && COMPILE_TEST)
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
help
|
|
Say Y here if you want PCIe controller support on R-Car SoCs.
|
|
|
|
config PCI_HOST_COMMON
|
|
bool
|
|
select PCI_ECAM
|
|
|
|
config PCI_HOST_GENERIC
|
|
bool "Generic PCI host controller"
|
|
depends on (ARM || ARM64) && OF
|
|
select PCI_HOST_COMMON
|
|
select IRQ_DOMAIN
|
|
help
|
|
Say Y here if you want to support a simple generic PCI host
|
|
controller, such as the one emulated by kvmtool.
|
|
|
|
config PCIE_XILINX
|
|
bool "Xilinx AXI PCIe host bridge support"
|
|
depends on ARCH_ZYNQ || MICROBLAZE || (MIPS && PCI_DRIVERS_GENERIC)
|
|
help
|
|
Say 'Y' here if you want kernel to support the Xilinx AXI PCIe
|
|
Host Bridge driver.
|
|
|
|
config PCI_XGENE
|
|
bool "X-Gene PCIe controller"
|
|
depends on ARM64
|
|
depends on OF || (ACPI && PCI_QUIRKS)
|
|
select PCIEPORTBUS
|
|
help
|
|
Say Y here if you want internal PCI support on APM X-Gene SoC.
|
|
There are 5 internal PCIe ports available. Each port is GEN3 capable
|
|
and have varied lanes from x1 to x8.
|
|
|
|
config PCI_XGENE_MSI
|
|
bool "X-Gene v1 PCIe MSI feature"
|
|
depends on PCI_XGENE
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
default y
|
|
help
|
|
Say Y here if you want PCIe MSI support for the APM X-Gene v1 SoC.
|
|
This MSI driver supports 5 PCIe ports on the APM X-Gene v1 SoC.
|
|
|
|
config PCI_V3_SEMI
|
|
bool "V3 Semiconductor PCI controller"
|
|
depends on OF
|
|
depends on ARM
|
|
default ARCH_INTEGRATOR_AP
|
|
|
|
config PCI_VERSATILE
|
|
bool "ARM Versatile PB PCI controller"
|
|
depends on ARCH_VERSATILE
|
|
|
|
config PCIE_IPROC
|
|
tristate
|
|
select PCI_DOMAINS
|
|
help
|
|
This enables the iProc PCIe core controller support for Broadcom's
|
|
iProc family of SoCs. An appropriate bus interface driver needs
|
|
to be enabled to select this.
|
|
|
|
config PCIE_IPROC_PLATFORM
|
|
tristate "Broadcom iProc PCIe platform bus driver"
|
|
depends on ARCH_BCM_IPROC || (ARM && COMPILE_TEST)
|
|
depends on OF
|
|
select PCIE_IPROC
|
|
default ARCH_BCM_IPROC
|
|
help
|
|
Say Y here if you want to use the Broadcom iProc PCIe controller
|
|
through the generic platform bus interface
|
|
|
|
config PCIE_IPROC_BCMA
|
|
tristate "Broadcom iProc PCIe BCMA bus driver"
|
|
depends on ARM && (ARCH_BCM_IPROC || COMPILE_TEST)
|
|
select PCIE_IPROC
|
|
select BCMA
|
|
default ARCH_BCM_5301X
|
|
help
|
|
Say Y here if you want to use the Broadcom iProc PCIe controller
|
|
through the BCMA bus interface
|
|
|
|
config PCIE_IPROC_MSI
|
|
bool "Broadcom iProc PCIe MSI support"
|
|
depends on PCIE_IPROC_PLATFORM || PCIE_IPROC_BCMA
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
default ARCH_BCM_IPROC
|
|
help
|
|
Say Y here if you want to enable MSI support for Broadcom's iProc
|
|
PCIe controller
|
|
|
|
config PCIE_ALTERA
|
|
bool "Altera PCIe controller"
|
|
depends on ARM || NIOS2
|
|
depends on OF_PCI
|
|
select PCI_DOMAINS
|
|
help
|
|
Say Y here if you want to enable PCIe controller support on Altera
|
|
FPGA.
|
|
|
|
config PCIE_ALTERA_MSI
|
|
bool "Altera PCIe MSI feature"
|
|
depends on PCIE_ALTERA
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
help
|
|
Say Y here if you want PCIe MSI support for the Altera FPGA.
|
|
This MSI driver supports Altera MSI to GIC controller IP.
|
|
|
|
config PCI_HOST_THUNDER_PEM
|
|
bool "Cavium Thunder PCIe controller to off-chip devices"
|
|
depends on ARM64
|
|
depends on OF || (ACPI && PCI_QUIRKS)
|
|
select PCI_HOST_COMMON
|
|
help
|
|
Say Y here if you want PCIe support for CN88XX Cavium Thunder SoCs.
|
|
|
|
config PCI_HOST_THUNDER_ECAM
|
|
bool "Cavium Thunder ECAM controller to on-chip devices on pass-1.x silicon"
|
|
depends on ARM64
|
|
depends on OF || (ACPI && PCI_QUIRKS)
|
|
select PCI_HOST_COMMON
|
|
help
|
|
Say Y here if you want ECAM support for CN88XX-Pass-1.x Cavium Thunder SoCs.
|
|
|
|
config PCIE_ROCKCHIP
|
|
tristate "Rockchip PCIe controller"
|
|
depends on ARCH_ROCKCHIP || COMPILE_TEST
|
|
depends on OF
|
|
depends on PCI_MSI_IRQ_DOMAIN
|
|
select MFD_SYSCON
|
|
help
|
|
Say Y here if you want internal PCI support on Rockchip SoC.
|
|
There is 1 internal PCIe port available to support GEN2 with
|
|
4 slots.
|
|
|
|
config PCIE_MEDIATEK
|
|
bool "MediaTek PCIe controller"
|
|
depends on (ARM || ARM64) && (ARCH_MEDIATEK || COMPILE_TEST)
|
|
depends on OF
|
|
depends on PCI
|
|
select PCIEPORTBUS
|
|
help
|
|
Say Y here if you want to enable PCIe controller support on
|
|
MediaTek SoCs.
|
|
|
|
config PCIE_TANGO_SMP8759
|
|
bool "Tango SMP8759 PCIe controller (DANGEROUS)"
|
|
depends on ARCH_TANGO && PCI_MSI && OF
|
|
depends on BROKEN
|
|
select PCI_HOST_COMMON
|
|
help
|
|
Say Y here to enable PCIe controller support for Sigma Designs
|
|
Tango SMP8759-based systems.
|
|
|
|
Note: The SMP8759 controller multiplexes PCI config and MMIO
|
|
accesses, and Linux doesn't provide a way to serialize them.
|
|
This can lead to data corruption if drivers perform concurrent
|
|
config and MMIO accesses.
|
|
|
|
config VMD
|
|
depends on PCI_MSI && X86_64 && SRCU
|
|
tristate "Intel Volume Management Device Driver"
|
|
default N
|
|
---help---
|
|
Adds support for the Intel Volume Management Device (VMD). VMD is a
|
|
secondary PCI host bridge that allows PCI Express root ports,
|
|
and devices attached to them, to be removed from the default
|
|
PCI domain and placed within the VMD domain. This provides
|
|
more bus resources than are otherwise possible with a
|
|
single domain. If you know your system provides one of these and
|
|
has devices attached to it, say Y; if you are not sure, say N.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called vmd.
|
|
|
|
endmenu
|