* Tweak phy activation -> rx delay for different bwmodes
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we set antenna flags on phy init and ack bitrate
mode on pcu init, there is no need to save/restore sta_id
flags on ath5k_hw_reset. Also we don't need to re-set our
mac address because it's not affected by resets.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add synth-only channel change for AR2413/5413. When we call
ath5k_reset with a channel ath5k_hw_reset will first try to
set channel on PHY while PHY is running instead of doing a normal
full reset. To do this phy_init has to change to implement this
functionality.
* Clean up change_channel flag, what it really did was skip PCU
registers when setting initvals. This is done because on reset
PCU registers are not affected (except the registers we set
in pcu init and -due to hw problems- TSF). Use a new skip_pcu
flag that's not misleading instead. In the future we might use
that to also skip PCU reset and save us the TSF etc problems
(needs testing because standard practice is to reset everything).
* Use fast channel change only when setting channel, and set skip_pcu
to false only on init. When we reset the card due to DMA or PHY
problems skip pcu but never do a fast channel change.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Only set power table if we are changing channel/mode
there is no need to recalculate and reset the power table
all the time.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set correct PLL settings for each bwmode
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add spur mitigation filter support for half/quarter and turbo.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Tweak power detector delays on AR5111/AR5112 when
using half/quarter modes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Make sure we always set IFS timings even if no
coverage class is set. If we don't we'll miss the
needed changes for different bwmodes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set AR5K_DCU_GBL_IFS_MISC_TURBO_MODE flag on DCU when operating
on 40MHz
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Replace set_slot_time with set_ifs_intervals that also sets
the various inter-frame space intervals based on current bwmode.
* Clean up AR5210 mess from reset_tx_queue, AR5210 only has one
data queue and we set IFS intervals for that queue on set_ifs_intervals
so there is nothing left to do for 5210 on reset_tx_queue.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Extend ieee80211_generic_frame_duration to support the various
bwmodes.
* Better document what's going on with ack bitrates and update
write_rate_duration to support the standard ack bitrates (when
we don't set the high bit).
* Get rid of set_ack_bitrate_high and introduce a flag on ath5k_hw
for this (we only called the function on init anyway so there is no
difference).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Extend get_default_sifs/slot_time to include timings for turbo
half and quarter rate modes.
* AR5210 code for now uses timings already on core clock units
instead of usecs so rename them (we 'll clean it up later).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Move setting of tx retry limits on a separate function
(we 'll clean up this AR5210 mess later)
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* On turbo mode increase PHY settling times, note that
we only increase switch settling time on AR5212 as indicated
by initvals.
* A few cleanups: Move frame control settings for AR5210 from
reset_tx_queue to tweak_initvals and remove phy_scal settings
from tweak_initvals (we tweak them alread on set_sleep_clock).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Now that we properly set rx/tx latencies for AR5311 remove
that old buggy part of code left inside ath5k_hw_tweak_initval_settings
that was never executed (you can't have an RF5112 radio on a mac older
than AR5212). Also use a magic value for 5311 PHY_SCAL value.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Handle all usec parameters in one function. It's much cleaner
this way.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Prepare for half/quarter/turbo support, introduce a new
ah_bwmode parameter and get rid of ah_turbo. Bwmode stands
for "bandwidth mode" and can have 4 values, default (20MHz),
turbo (40MHz), half rate (10MHz), and quarter rate (5MHz).
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we only use ath5k_hw_stop_tx_dma to stop the beacon
queue, introduce a new function ath5k_hw_stop_beacon_queue so
that we can use that instead and have better control. In the future
we can add more beacon queue specific stuff there (maybe tweak
beacon timers or something), for now just call ath5k_hw_stop_tx_dma.
* Also since we don't call ath5k_hw_stop_rx/tx_dma from outside
dma.c, make them static.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Make sure we are not trying to set RXDP while RX is active,
for now ignore the return value.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* DCU early termination should be used to quickly flush QCU
according to docs so don't enable it for all queues, enable
it only when stopping each queue and disable it when we are
done.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Increase timeouts on ath5k_hw_stop_tx_dma and also wait for
tx queue to stop before checking for pending frames
* Add a new debug level to debug dma start/stop
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we stop rx/tx dma and pcu durring reset there is no need to
call ath5k_hw_stop_rx/tx_dma before, also there is no need to call
them durring stop_locked since we can use ath5k_hw_dma_stop for
both.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Stop PCU receive logic (DRU) durring reset
We need to be sure pcu is not active when trying to stop rx dma
right now this is done on ath5k_reset (base.c) but later we are
going to clean it up.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add a new function to stop rx/tx dma and use in when reset starts
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* No functional changes
* Clean up reset:
Introduce init functions for each unit and call them instead
of having everything inside ath5k_hw_reset (it's just c/p for
now so nothing changes except calling order -I tested it with
various cards and it's ok-)
* Further cleanups:
ofdm_timings belongs to phy.c
rate_duration belongs to pcu.c
clock functions are general and belong to reset.c (more to follow)
* Reorder functions for better organization:
We start with helpers and other functions follow in categories,
init functions are last
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.
This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_RxKeyIdxValid will not be set for bcast/mcast frames and so relying
this status for MIC failed frames is buggy.
Due to this, MIC failure events for broadcast frames are not sent to
supplicant resulted in AP disconnecting the STA.
Able to pass Wifi Test case 5.2.18 with this fix.
Cc: Stable <stable@kernel.org> (2.6.36+)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Th commit titled "mac80211: clean up rx handling wrt. found_sta"
removed found_sta variable which caused a MIC failure event
to be reported twice for a single failure to supplicant resulted
in STA disconnect.
This should fix WPA specific countermeasures WiFi test case (5.2.17)
issues with mac80211 based drivers which report MIC failure events in
rx status.
Cc: Stable <stable@kernel.org> (2.6.37)
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an curious issue due to insufficient
rx frame filtering.
Saqeb Akhter reported frequent disconnects while streaming
videos over samba: <http://marc.info/?m=128600031109136>
> [ 1166.512087] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 1526.059997] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [ 2125.324356] wlan1: deauthenticated from 30:46:9a:10:49:f7 (Reason: 7)
> [...]
The reason is that the device generates frames with slightly
bogus SA/TA addresses.
e.g.:
[ 2314.402316] Ignore 9f:1f:31:f8:64:ff
[ 2314.402321] Ignore 9f:1f:31:f8:64:ff
[ 2352.453804] Ignore 0d:1f:31:f8:64:ff
[ 2352.453808] Ignore 0d:1f:31:f8:64:ff
^^ the group-address flag is set!
(the correct SA/TA would be: 00:1f:31:f8:64:ff)
Since the AP does not know from where the frames come, it
generates a DEAUTH response for the (invalid) mcast address.
This mcast deauth frame then passes through all filters and
tricks the stack into thinking that the AP brutally kicked
us!
This patch fixes the problem by simply ignoring
non-broadcast, group-addressed deauth/disassoc frames.
Cc: Jouni Malinen <j@w1.fi>
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Saqeb Akhter <saqeb.akhter@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The RX aggregation locking documentation was
wrong, which led Christian to also code the
timer timeout handling for it somewhat wrongly.
Fix the documentation, the two places that
need to hold the reorder lock across accesses
to the structure, and the debugfs code that
should just use RCU.
Also, remove acquiring the sta->lock across
reorder timeouts since it isn't necessary, and
change a few places to GFP_KERNEL because the
code path here doesn't need atomic allocations
as I noticed when reviewing all this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent tx path cleanups moved the software retry count tracking
from the ath_buf to the skb cb, however the actual counter update
referred to the wrong location, confusing block-ack window tracking.
Fix this by using the retries counter in the struct ath_frame_info.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 446fad5a5b.
The change had broken the packet injection on monitoring mode.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not ideal to enable btcoex based on subsys id as it is
not unique, they are so random. It is also a pain keeping
all of them in a table to enable btcoex for a particular
hw. Going back to the old idea.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This implements the new off-channel TX API
in mac80211 with a new work item type. The
operation doesn't add a new work item when
we're on the right channel and there's no
wait time so that for example p2p probe
responses will be transmitted without delay.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With p2p, it is sometimes necessary to transmit
a frame (typically an action frame) on another
channel than the current channel. Enable this
through the CMD_FRAME API, and allow it to wait
for a response. A new command allows that wait
to be aborted.
However, allow userspace to specify whether or
not it wants to allow off-channel TX, it may
actually want to use the same channel only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit: "carl9170: revamp carl9170_tx_prepare"
introduced a peculiar bug that would only show
up if the the module parameter noht is set to 1.
Then all outbound voice, video and background
frames would each invoke a (bogus) RTS/CTS
handshake.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order for frame injection to work properly for some use cases
(e.g., finding the station entry and keys for encryption), mac80211
needs to find the correct sdata entry. This works when the main vif
is in AP mode, but commit a2c1e3dad5
broke this particular use case for station main vif. While this type of
injection is quite unusual operation, it has some uses and we should fix
it. Do this by changing the monitor vif sdata selection to allow station
vif to be selected instead of limiting it to just AP vifs. We still need
to skip some iftypes to avoid selecting unsuitable vif for injection.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
while removing beaconing mode interface, SWBA interrupt
was never disabled when there are no other beaconing interfaces.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With some upcoming changes we'd like to use
the interface types for P2P capability tests.
Enable them now so that when we add those
tests in wpa_supplicant, nothing will break.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k driver uses a shared pm_qos_request_list structure for all
devices. This causes the following warning if more than one device is
present in the system:
WARNING: at kernel/pm_qos_params.c:234 ath9k_init_device+0x5e8/0x6b0()
pm_qos_add_request() called for already added request
Modules linked in:
Call Trace:
[<802b1cdc>] dump_stack+0x8/0x34
[<8007dd90>] warn_slowpath_common+0x78/0xa4
[<8007de44>] warn_slowpath_fmt+0x2c/0x38
[<801b0828>] ath9k_init_device+0x5e8/0x6b0
[<801bc508>] ath_pci_probe+0x2dc/0x39c
[<80176254>] pci_device_probe+0x64/0xa4
[<8019471c>] driver_probe_device+0xbc/0x188
[<80194854>] __driver_attach+0x6c/0xa4
[<80193e20>] bus_for_each_dev+0x60/0xb0
[<80193580>] bus_add_driver+0xcc/0x268
[<80194c08>] driver_register+0xe0/0x198
[<801764e0>] __pci_register_driver+0x50/0xe0
[<80365f48>] ath9k_init+0x3c/0x6c
[<8006050c>] do_one_initcall+0xfc/0x1d8
[<80355340>] kernel_init+0xd4/0x174
[<800639a4>] kernel_thread_helper+0x10/0x18
---[ end trace 5345fc6f870564a6 ]---
This patch fixes that warning by using a separate pm_qos_request_list
sructure for each device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
card->priv must not be accessed after lbs_remove_card() was called
as lbs_remove_card() frees card->priv via free_netdev().
For libertas_sdio this is a regression introduced by 23b149c189.
The correct fix to the issue described there is simply to remove the
assignment. This flag is set at the appropriate time inside
lbs_remove_card anyway.
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"priv" is stored at the end of the wiphy structure, which is freed
during the call to lbs_cfg_free(). It must not be touched afterwards.
Remove the unnecessary NULL assignment causing this memory corruption.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change to offical name for 100 devices:
"Intel(R) Centrino(R) Wireless-N 100"
Change to offical name for 130 devices:
"Intel(R) Centrino(R) Wireless-N 130"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Change to offical name for 6000g2b devices:
"Intel(R) Centrino(R) Wireless-N 1030"
"Intel(R) Centrino(R) Advanced-N 6230"
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
