Arm64 hardware does not always report a watchpoint hit address that
matches one of the watchpoints set. It can also report an address
"near" the watchpoint if a single instruction access both watched and
unwatched addresses. There is no straight-forward way, short of
disassembling the offending instruction, to map that address back to
the watchpoint.
Previously, when the hardware reported a watchpoint hit on an address
that did not match our watchpoint (this happens in case of instructions
which access large chunks of memory such as "stp") the process would
enter a loop where we would be continually resuming it (because we did
not recognise that watchpoint hit) and it would keep hitting the
watchpoint again and again. The tracing process would never get
notified of the watchpoint hit.
This commit fixes the problem by looking at the watchpoints near the
address reported by the hardware. If the address does not exactly match
one of the watchpoints we have set, it attributes the hit to the
nearest watchpoint we have. This heuristic is a bit dodgy, but I don't
think we can do much more, given the hardware limitations.
Signed-off-by: Pavel Labath <labath@google.com>
[panand: reworked to rebase on his patches]
Signed-off-by: Pratyush Anand <panand@redhat.com>
[will: use __ffs instead of ffs - 1]
Signed-off-by: Will Deacon <will.deacon@arm.com>
ARM64 hardware supports watchpoint at any double word aligned address.
However, it can select any consecutive bytes from offset 0 to 7 from that
base address. For example, if base address is programmed as 0x420030 and
byte select is 0x1C, then access of 0x420032,0x420033 and 0x420034 will
generate a watchpoint exception.
Currently, we do not have such modularity. We can only program byte,
halfword, word and double word access exception from any base address.
This patch adds support to overcome above limitations.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The arm64 hw_breakpoint implementation uses a CPU hotplug notifier to
reset the {break,watch}point registers when CPUs come online.
This patch converts the code to the new hotplug mechanism, whilst moving
the invocation earlier to remove the need to disable IRQs explicitly in
the driver (which could cause havok if we trip a watchpoint in an IRQ
handler whilst restoring the debug register state).
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Add all function symbols which are called from do_debug_exception under
NOKPROBE_SYMBOL, as they can not kprobed.
Signed-off-by: Pratyush Anand <panand@redhat.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
- virt_to_page/page_address optimisations
- Support for NUMA systems described using device-tree
- Support for hibernate/suspend-to-disk
- Proper support for maxcpus= command line parameter
- Detection and graceful handling of AArch64-only CPUs
- Miscellaneous cleanups and non-critical fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJXNbgkAAoJELescNyEwWM0PtcIAK11xaOMmSqXz8fcTeNLw4dS
taaPWhjCYus8EhJyvTetfwk74+qVApdvKXKNKgODJXQEjeQx2brdUfbQZb31DTGT
798UYCAyEYCWkXspqi+/dpZEgUGPYH7uGOu2eDd19+PhTeX/EQSRX3fC9k0BNhvh
PN9pOgRcKAlIExZ6QYmT0g56VLtbCfFShN41mQ8HdpShl6pPJuhQ+kDDzudmRjuD
11/oYuOaVTnwbPuXn+sjOrWvMkfINHI70BAQnnBs0v+5c45mzpqEMsy0dYo2Pl2m
ar5lUFVIZggQkiqcOzqBzEgF+4gNw4LUu1DgK6cNKNMtL6k8E9zeOZMWeSVr0lg=
=bT5E
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Will Deacon:
- virt_to_page/page_address optimisations
- support for NUMA systems described using device-tree
- support for hibernate/suspend-to-disk
- proper support for maxcpus= command line parameter
- detection and graceful handling of AArch64-only CPUs
- miscellaneous cleanups and non-critical fixes
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (92 commits)
arm64: do not enforce strict 16 byte alignment to stack pointer
arm64: kernel: Fix incorrect brk randomization
arm64: cpuinfo: Missing NULL terminator in compat_hwcap_str
arm64: secondary_start_kernel: Remove unnecessary barrier
arm64: Ensure pmd_present() returns false after pmd_mknotpresent()
arm64: Replace hard-coded values in the pmd/pud_bad() macros
arm64: Implement pmdp_set_access_flags() for hardware AF/DBM
arm64: Fix typo in the pmdp_huge_get_and_clear() definition
arm64: mm: remove unnecessary EXPORT_SYMBOL_GPL
arm64: always use STRICT_MM_TYPECHECKS
arm64: kvm: Fix kvm teardown for systems using the extended idmap
arm64: kaslr: increase randomization granularity
arm64: kconfig: drop CONFIG_RTC_LIB dependency
arm64: make ARCH_SUPPORTS_DEBUG_PAGEALLOC depend on !HIBERNATION
arm64: hibernate: Refuse to hibernate if the boot cpu is offline
arm64: kernel: Add support for hibernate/suspend-to-disk
PM / Hibernate: Call flush_icache_range() on pages restored in-place
arm64: Add new asm macro copy_page
arm64: Promote KERNEL_START/KERNEL_END definitions to a header file
arm64: kernel: Include _AC definition in page.h
...
Since commit 1cf4f629d9 ("cpu/hotplug: Move online calls to
hotplugged cpu") it is ensured that callbacks of CPU_ONLINE and
CPU_DOWN_PREPARE are processed on the hotplugged CPU. Due to this SMP
function calls are no longer required.
Replace smp_call_function_single() with a direct call of
hw_breakpoint_reset(). To keep the calling convention, interrupts are
explicitly disabled around the call.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Set a default event->overflow_handler in perf_event_alloc() so don't
need to check event->overflow_handler in __perf_event_overflow().
Following commits can give a different default overflow_handler.
Initial idea comes from Peter:
http://lkml.kernel.org/r/20130708121557.GA17211@twins.programming.kicks-ass.net
Since the default value of event->overflow_handler is not NULL, existing
'if (!overflow_handler)' checks need to be changed.
is_default_overflow_handler() is introduced for this.
No extra performance overhead is introduced into the hot path because in the
original code we still need to read this handler from memory. A conditional
branch is avoided so actually we remove some instructions.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <pi3orama@163.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Zefan Li <lizefan@huawei.com>
Link: http://lkml.kernel.org/r/1459147292-239310-3-git-send-email-wangnan0@huawei.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A prior commit used to detect the hw breakpoint ABI behaviour based on
the target state missed the asm/compat.h include and the build fails
with !CONFIG_COMPAT.
Fixes: 8f48c06290 ("arm64: hw_breakpoint: use target state to determine ABI behaviour")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The arm64 hw_breakpoint interface is slightly less flexible than its
32-bit counterpart, thanks to some changes in the architecture rendering
unaligned watchpoint addresses obselete for AArch64.
However, in a multi-arch environment (i.e. debugging a 32-bit target
with a 64-bit GDB under a 64-bit kernel), we need to provide a feature
compatible interface to GDB in order for debugging to function correctly.
This patch adds a new helper, is_compat_bp, to our hw_breakpoint
implementation which changes the interface behaviour based on the
architecture of the debug target as opposed to the debugger itself.
This allows debugged to function as expected for multi-arch
configurations without relying on deprecated architectural behaviours
when debugging native applications.
Cc: Yao Qi <yao.qi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
We have a couple of CPU hotplug notifiers for resetting the CPU debug
state to a sane value when a CPU comes online.
This patch ensures that we mask out CPU_TASKS_FROZEN so that we don't
miss any online events occuring due to suspend/resume.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
lib/list_sort.c defines a 'struct debug_el', where "el" is assumedly a
a contraction of "element". This conflicts with 'enum debug_el' in our
asm/debug-monitors.h header file, where "el" stands for Exception Level.
The result is build failure when targetting allmodconfig, so rename our
enum to 'dbg_active_el' to be slightly more explicit about what it is.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Finally advertise the KVM capability for SET_GUEST_DEBUG. Once arm
support is added this check can be moved to the common
kvm_vm_ioctl_check_extension() code.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
ARM64_CPU_SUSPEND config option was introduced to make code providing
context save/restore selectable only on platforms requiring power
management capabilities.
Currently ARM64_CPU_SUSPEND depends on the PM_SLEEP config option which
in turn is set by the SUSPEND config option.
The introduction of CPU_IDLE for arm64 requires that code configured
by ARM64_CPU_SUSPEND (context save/restore) should be compiled in
in order to enable the CPU idle driver to rely on CPU operations
carrying out context save/restore.
The ARM64_CPUIDLE config option (ARM64 generic idle driver) is therefore
forced to select ARM64_CPU_SUSPEND, even if there may be (ie PM_SLEEP)
failed dependencies, which is not a clean way of handling the kernel
configuration option.
For these reasons, this patch removes the ARM64_CPU_SUSPEND config option
and makes the context save/restore dependent on CPU_PM, which is selected
whenever either SUSPEND or CPU_IDLE are configured, cleaning up dependencies
in the process.
This way, code previously configured through ARM64_CPU_SUSPEND is
compiled in whenever a power management subsystem requires it to be
present in the kernel (SUSPEND || CPU_IDLE), which is the behaviour
expected on ARM64 kernels.
The cpu_suspend and cpu_init_idle CPU operations are added only if
CPU_IDLE is selected, since they are CPU_IDLE specific methods and
should be grouped and defined accordingly.
PSCI CPU operations are updated to reflect the introduced changes.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Some kernel files may include both linux/compat.h and asm/compat.h directly
or indirectly. Since both header files contain is_compat_task() under
!CONFIG_COMPAT, compiling them with !CONFIG_COMPAT will eventually fail.
Such files include kernel/auditsc.c, kernel/seccomp.c and init/do_mountfs.c
(do_mountfs.c may read asm/compat.h via asm/ftrace.h once ftrace is
implemented).
So this patch proactively
1) removes is_compat_task() under !CONFIG_COMPAT from asm/compat.h
2) replaces asm/compat.h to linux/compat.h in kernel/*.c,
but asm/compat.h is still necessary in ptrace.c and process.c because
they use is_compat_thread().
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the hw-breakpoint code in arm64 by using this latter form of callback
registration.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Lorenzo Pieralisi <Lorenzo.Pieralisi@arm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a CPU resumes from low-power, it restores HW breakpoint and
watchpoint slots through a CPU PM notifier. Since we want to enable
debugging as early as possible in the resume path, the mdscr content
is restored along the general purpose registers in the cpu_suspend API
and debug exceptions are reenabled when cpu_suspend returns. Since the
CPU PM notifier is run after a CPU has been resumed, we cannot expect
HW breakpoint registers to contain sane values till the notifier is run,
since the HW breakpoints registers content is unknown at reset; this means
that the CPU might run with debug exceptions enabled, mdscr restored but HW
breakpoint registers containing junk values that can trigger spurious
debug exceptions.
This patch fixes current HW breakpoints restore by moving the HW breakpoints
registers restoration to the cpu_suspend API, before the debug exceptions are
enabled. This way, as soon as the cpu_suspend function returns the
kernel can resume debugging with sane values in HW breakpoint registers.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When a CPU is shutdown either through CPU idle or suspend to RAM, the
content of HW breakpoint registers must be reset or restored to proper
values when CPU resume from low power states. This patch adds debug register
restore operations to the HW breakpoint control function and implements a
CPU PM notifier that allows to restore the content of HW breakpoint registers
to allow proper suspend/resume operations.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Most of the code executed to install and uninstall breakpoints is
common and can be factored out in a function that through a runtime
operations type provides the requested implementation.
This patch creates a common function that can be used to install/uninstall
breakpoints and defines the set of operations that can be carried out
through it.
Reviewed-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
This is the ARM part of Christoph's patchset cleaning up the various
uses of __get_cpu_var across the tree.
The idea is to convert __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations
that use the offset. Thereby address calculations are avoided and fewer
registers are used when code is generated.
[will: fixed debug ref counting checks and pcpu array accesses]
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/arm64 uses of the __cpuinit macros from
all C files. Currently arm64 does not have any __CPUINIT used in
assembly files.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
