RFC 8200 (IPv6) defines Hop-by-Hop options and Destination options
extension headers. Both of these carry a list of TLVs which is
only limited by the maximum length of the extension header (2048
bytes). By the spec a host must process all the TLVs in these
options, however these could be used as a fairly obvious
denial of service attack. I think this could in fact be
a significant DOS vector on the Internet, one mitigating
factor might be that many FWs drop all packets with EH (and
obviously this is only IPv6) so an Internet wide attack might not
be so effective (yet!).
By my calculation, the worse case packet with TLVs in a standard
1500 byte MTU packet that would be processed by the stack contains
1282 invidual TLVs (including pad TLVS) or 724 two byte TLVs. I
wrote a quick test program that floods a whole bunch of these
packets to a host and sure enough there is substantial time spent
in ip6_parse_tlv. These packets contain nothing but unknown TLVS
(that are ignored), TLV padding, and bogus UDP header with zero
payload length.
25.38% [kernel] [k] __fib6_clean_all
21.63% [kernel] [k] ip6_parse_tlv
4.21% [kernel] [k] __local_bh_enable_ip
2.18% [kernel] [k] ip6_pol_route.isra.39
1.98% [kernel] [k] fib6_walk_continue
1.88% [kernel] [k] _raw_write_lock_bh
1.65% [kernel] [k] dst_release
This patch adds configurable limits to Destination and Hop-by-Hop
options. There are three limits that may be set:
- Limit the number of options in a Hop-by-Hop or Destination options
extension header.
- Limit the byte length of a Hop-by-Hop or Destination options
extension header.
- Disallow unrecognized options in a Hop-by-Hop or Destination
options extension header.
The limits are set in corresponding sysctls:
ipv6.sysctl.max_dst_opts_cnt
ipv6.sysctl.max_hbh_opts_cnt
ipv6.sysctl.max_dst_opts_len
ipv6.sysctl.max_hbh_opts_len
If a max_*_opts_cnt is less than zero then unknown TLVs are disallowed.
The number of known TLVs that are allowed is the absolute value of
this number.
If a limit is exceeded when processing an extension header the packet is
dropped.
Default values are set to 8 for options counts, and set to INT_MAX
for maximum length. Note the choice to limit options to 8 is an
arbitrary guess (roughly based on the fact that the stack supports
three HBH options and just one destination option).
These limits have being proposed in draft-ietf-6man-rfc6434-bis.
Tested (by Martin Lau)
I tested out 1 thread (i.e. one raw_udp process).
I changed the net.ipv6.max_dst_(opts|hbh)_number between 8 to 2048.
With sysctls setting to 2048, the softirq% is packed to 100%.
With 8, the softirq% is almost unnoticable from mpstat.
v2;
- Code and documention cleanup.
- Change references of RFC2460 to be RFC8200.
- Add reference to RFC6434-bis where the limits will be in standard.
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains two one-liner fixes for your net tree,
they are:
1) Disable fast hash operations for 2-bytes length keys which is leading
to incorrect lookups in nf_tables, from Anatole Denis.
2) Reload pointer ipv4 header after ip_route_me_harder() given this may
result in use-after-free due to skbuff header reallocation, patch
from Tejaswi Tanikella.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Average RTT could become zero. This happened in real life at least twice.
This patch treats zero as 1us.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Acked-by: Lawrence Brakmo <Brakmo@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the only user, mlx5 driver does the check in
mlx5e_setup_tc_block_cb, no need to check here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-11-01
Here's one more bluetooth-next pull request for the 4.15 kernel.
- New NFA344A device entry for btusb drvier
- Fix race conditions in hci_ldisc
- Fix for isochronous interface assignments in btusb driver
- A few other smaller fixes & improvements
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.
One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.
This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
David reported breakages of VRF scenarios due to the
commit 6e617de84e ("net: avoid a full fib lookup when rp_filter is
disabled."): the local addresses based test is too strict when VRFs
are in place.
With this change we fall-back to a full lookup when custom fib rules
are in place; so that we address the VRF use case and possibly other
similar issues in non trivial setups.
v1 -> v2:
- fix build breakage when CONFIG_IP_MULTIPLE_TABLES is not defined,
reported by the kbuild test robot
Reported-by: David Ahern <dsahern@gmail.com>
Fixes: 6e617de84e ("net: avoid a full fib lookup when rp_filter is disabled.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to returnerror code -ENOMEM from the sctp_make_strreset_addstrm()
error handling case instead of 0. 'retval' can be overwritten to 0 after
call sctp_stream_alloc_out().
Fixes: e090abd0d8 ("sctp: factor out stream->out allocation")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on SNMP values provided by Roman, Yuchung made the observation
that some crashes in tcp_sacktag_walk() might be caused by MTU probing.
Looking at tcp_mtu_probe(), I found that when a new skb was placed
in front of the write queue, we were not updating tcp highest sack.
If one skb is freed because all its content was copied to the new skb
(for MTU probing), then tp->highest_sack could point to a now freed skb.
Bad things would then happen, including infinite loops.
This patch renames tcp_highest_sack_combine() and uses it
from tcp_mtu_probe() to fix the bug.
Note that I also removed one test against tp->sacked_out,
since we want to replace tp->highest_sack regardless of whatever
condition, since keeping a stale pointer to freed skb is a recipe
for disaster.
Fixes: a47e5a988a ("[TCP]: Convert highest_sack to sk_buff to allow direct access")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the error messages displayed in kernel log to include
hwaddress of the source machine that caused ipv6 duplicate address
detection failures.
Examples:
a) When we receive a NA packet from another machine advertising our
address:
ICMPv6: NA: 34🆎cd:56:11:e8 advertised our address 2001:db8:: on eth0!
b) When we detect DAD failure during address assignment to an interface:
IPv6: eth0: IPv6 duplicate address 2001:db8:: used by 34🆎cd:56:11:e8
detected!
v2:
Changed %pI6 to %pI6c in ndisc_recv_na()
Chaged the v6 address in the commit message to 2001:db8::
Suggested-by: Igor Lubashev <ilubashe@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Code refactoring in order to make the code easier to read and maintain.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
niph is not updated after pskb_expand_head changes the skb head. It
still points to the freed data, which is then used to update tot_len and
checksum. This could cause use-after-free poison crash.
Update niph, if ip_route_me_harder does not fail.
This only affects the interaction with REJECT targets and br_netfilter.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-11-01
1) Fix a memleak when a packet matches a policy
without a matching state.
2) Reset the socket cached dst_entry when inserting
a socket policy, otherwise the policy might be
ignored. From Jonathan Basseri.
3) Fix GSO for a IPsec, GRE tunnel combination.
We reset the encapsulation field at the skb
too erly, as a result GRE does not segment
GSO packets. Fix this by resetting the the
encapsulation field right before the
transformation where the inner headers get
invalid.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using SIT tunnels with VRFs works fine if the underlay device is in a
VRF and the link parameter is set to the VRF device. e.g.,
ip tunnel add jtun mode sit remote <addr> local <addr> dev myvrf
Update the device check to allow the link to be the enslaved device as
well. e.g.,
ip tunnel add jtun mode sit remote <addr> local <addr> dev eth4
where eth4 is enslaved to myvrf.
Reported-by: Jeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for IFLA_BRPORT_NEIGH_SUPPRESS to bridge port policies.
Fixes: 821f1b21ca ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the time being I will be available in my private mail. Update both the
MAINTAINERS file and the individual modules MODULE_AUTHOR directive with
the new address.
Signed-off-by: Yotam Gigi <yotam.gi@gmail.com>
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-10-30
1) Change some variables that can't be negative
from int to unsigned int. From Alexey Dobriyan.
2) Remove a redundant header initialization in esp6.
From Colin Ian King.
3) Some BUG to BUG_ON conversions.
From Gustavo A. R. Silva.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the swap macro and remove unnecessary variable tmp.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike ipip and gre, ip_vti never uses err_count in vti4_err,
so no need to check err_count in vti_xmit, it's value always 0.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack to fib_notifier_info and plumb through stack to
call_fib_rule_notifiers, call_fib_entry_notifiers and
call_fib6_entry_notifiers. This allows notifer handlers to
return messages to user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NLMSGERR API already carries data (eg, a cookie) on the success path.
Allow a message string to be returned as well.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that slave dsa_port always have their name set, there is no need to
pass it to dsa_slave_create() anymore. Remove this argument.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get the optional "label" property and assign a default one directly at
parse time instead of doing it when creating the slave.
For legacy, simply assign the port name stored in cd->port_names.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fetching the master device can be done directly when a port is parsed
from device tree or pdata, instead of waiting until dsa_dst_parse.
Now that -EPROBE_DEFER is returned before we add the switch to the tree,
there is no need to check for this error after dsa_dst_parse.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign a port's type at parsed time instead of waiting for the tree to
be completed.
Because this is now done earlier, we can use the port's type in
dsa_port_is_* helpers instead of digging again in topology description.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add symmetrical DSA port parsing functions for pdata and device tree,
used to parse and validate a given port node or platform data.
They don't do much for the moment but will be extended later on to
assign a port type and get device references.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point into hiding the -EINVAL error code in ERR_PTR from a
dsa_get_ports function, simply get the "ports" node directly from within
the dsa_parse_ports_dn function.
This also has the effect to make the pdata and device tree handling code
symmetrical inside _dsa_register_switch.
At the same time, rename dsa_parse_ports_dn to dsa_parse_ports_of
because _of is a more common suffix for device tree parsing functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2017-10-31
This series contains updates to i40e, i40evf and net/sched.
Arnd Bergmann cleans up the power management code to resolve a build
warning.
Shannon Nelson fixes i40e to only redistribute our vectors when we did
not get the full count that we requested.
Alex reverts a previous commit because it potentially causes a memory leak
when combined with the current page recycling scheme.
Amritha enables configuring cloud filters in i40e using the tc-flower
classifier. The classification function of the filter is to match a
packet to a traffic class. cls_flower is extended to offload classid to
hardware. Hardware traffic classes are identified using classid values
reserved in the range :ffe0 - :ffef.
The cloud filters are added for a VSI and are cleaned up when the VSI is
deleted. The filters that match on L4 ports needs enhanced admin queue
functions with big buffer support for extended fields in cloud filter
commands.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
With conversion to refcount_t, such manual debugging code doesn't make
sense anymore.
The tunnel part was already dropped by
54652eb12c ("l2tp: hold tunnel while looking up sessions in l2tp_netlink").
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->ref() and ->deref() callbacks are unused since PPP stopped using
them in ee40fb2e1e ("l2tp: protect sock pointer of struct pppol2tp_session with RCU").
We can thus remove them from struct l2tp_session and drop the do_ref
parameter of l2tp_session_get*().
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch offloads the classid to hardware and uses the classid
reserved in the range :ffe0 - :ffef to identify hardware traffic
classes reported via dev->num_tc.
tcf_result structure contains the class ID of the class to which
the packet belongs and is offloaded to hardware via flower filter.
A new helper function is introduced to represent HW traffic
classes 0 through 15 using the reserved classid values :ffe0 - :ffef.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We reset the encapsulation field of the skb too early
in xfrm_output. As a result, the GRE GSO handler does
not segment the packets. This leads to a performance
drop down. We fix this by resetting the encapsulation
field right before we do the transformation, when
the inner headers become invalid.
Fixes: f1bd7d659e ("xfrm: Add encapsulation header offsets while SKB is not encrypted")
Reported-by: Vicente De Luca <vdeluca@zendesk.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
In commit 7aa0045dad ("net_sched: introduce a workqueue for RCU callbacks of tc filter")
I defer tcf_chain_flush() to a workqueue, this causes a use-after-free
because qdisc is already destroyed after we queue this work.
The tcf_block_put_deferred() is no longer necessary after we get RTNL
for each tc filter destroy work, no others could jump in at this point.
Same for tcf_chain_hold(), we are fully serialized now.
This also reduces one indirection therefore makes the code more
readable. Note this brings back a rcu_barrier(), however comparing
to the code prior to commit 7aa0045dad we still reduced one
rcu_barrier(). For net-next, we can consider to refcnt tcf block to
avoid it.
Fixes: 7aa0045dad ("net_sched: introduce a workqueue for RCU callbacks of tc filter")
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use l2tp_tunnel_get() in pppol2tp_connect() to ensure the tunnel isn't
going to disappear while processing the rest of the function.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
bpf_getsockopt bpf call sets the ret variable to zero and
never changes it. What's worse in case CONFIG_INET is
not selected the variable is completely unused generating
a warning.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several conflicts here.
NFP driver bug fix adding nfp_netdev_is_nfp_repr() check to
nfp_fl_output() needed some adjustments because the code block is in
an else block now.
Parallel additions to net/pkt_cls.h and net/sch_generic.h
A bug fix in __tcp_retransmit_skb() conflicted with some of
the rbtree changes in net-next.
The tc action RCU callback fixes in 'net' had some overlap with some
of the recent tcf_block reworking.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Mart reported a deadlock in -RT in the call path:
hci_send_monitor_ctrl_event() -> hci_send_to_channel()
because both functions acquire the same read lock hci_sk_list.lock. This
is also a mainline issue because the qrwlock implementation is writer
fair (the traditional rwlock implementation is reader biased).
To avoid the deadlock there is now __hci_send_to_channel() which expects
the readlock to be held.
Fixes: 38ceaa00d0 ("Bluetooth: Add support for sending MGMT commands and events to monitor")
Reported-by: Mart van de Wege <mvdwege@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) Fix route leak in xfrm_bundle_create().
2) In mac80211, validate user rate mask before configuring it. From
Johannes Berg.
3) Properly enforce memory limits in fair queueing code, from Toke
Hoiland-Jorgensen.
4) Fix lockdep splat in inet_csk_route_req(), from Eric Dumazet.
5) Fix TSO header allocation and management in mvpp2 driver, from Yan
Markman.
6) Don't take socket lock in BH handler in strparser code, from Tom
Herbert.
7) Don't show sockets from other namespaces in AF_UNIX code, from
Andrei Vagin.
8) Fix double free in error path of tap_open(), from Girish Moodalbail.
9) Fix TX map failure path in igb and ixgbe, from Jean-Philippe Brucker
and Alexander Duyck.
10) Fix DCB mode programming in stmmac driver, from Jose Abreu.
11) Fix err_count handling in various tunnels (ipip, ip6_gre). From Xin
Long.
12) Properly align SKB head before building SKB in tuntap, from Jason
Wang.
13) Avoid matching qdiscs with a zero handle during lookups, from Cong
Wang.
14) Fix various endianness bugs in sctp, from Xin Long.
15) Fix tc filter callback races and add selftests which trigger the
problem, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
selftests: Introduce a new test case to tc testsuite
selftests: Introduce a new script to generate tc batch file
net_sched: fix call_rcu() race on act_sample module removal
net_sched: add rtnl assertion to tcf_exts_destroy()
net_sched: use tcf_queue_work() in tcindex filter
net_sched: use tcf_queue_work() in rsvp filter
net_sched: use tcf_queue_work() in route filter
net_sched: use tcf_queue_work() in u32 filter
net_sched: use tcf_queue_work() in matchall filter
net_sched: use tcf_queue_work() in fw filter
net_sched: use tcf_queue_work() in flower filter
net_sched: use tcf_queue_work() in flow filter
net_sched: use tcf_queue_work() in cgroup filter
net_sched: use tcf_queue_work() in bpf filter
net_sched: use tcf_queue_work() in basic filter
net_sched: introduce a workqueue for RCU callbacks of tc filter
sctp: fix some type cast warnings introduced since very beginning
sctp: fix a type cast warnings that causes a_rwnd gets the wrong value
sctp: fix some type cast warnings introduced by transport rhashtable
sctp: fix some type cast warnings introduced by stream reconf
...
Similar to commit c78e1746d3
("net: sched: fix call_rcu() race on classifier module unloads"),
we need to wait for flying RCU callback tcf_sample_cleanup_rcu().
Cc: Yotam Gigi <yotamg@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After previous patches, it is now safe to claim that
tcf_exts_destroy() is always called with RTNL lock.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Defer the tcf_exts_destroy() in RCU callback to
tc filter workqueue and get RTNL lock.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a dedicated workqueue for tc filters
so that each tc filter's RCU callback could defer their
action destroy work to this workqueue. The helper
tcf_queue_work() is introduced for them to use.
Because we hold RTNL lock when calling tcf_block_put(), we
can not simply flush works inside it, therefore we have to
defer it again to this workqueue and make sure all flying RCU
callbacks have already queued their work before this one, in
other words, to ensure this is the last one to execute to
prevent any use-after-free.
On the other hand, this makes tcf_block_put() ugly and
harder to understand. Since David and Eric strongly dislike
adding synchronize_rcu(), this is probably the only
solution that could make everyone happy.
Please also see the code comments below.
Reported-by: Chris Mi <chrism@mellanox.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: John Fastabend <john.fastabend@gmail.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If command is added to req then it should be freed in case if
hdev is down or HCI_ADVERTISING flag is set.
This introduces a helper in hci_request to purge the cmd_q
to make cmd_q internal to hci_request which is used to fix
the leak.
This also replace accessing of cmd_q in hci_conn with the
new helper.
Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are there since very beginning.
Note after this patch, there still one warning left in
sctp_outq_flush():
sctp_chunk_fail(chunk, SCTP_ERROR_INV_STRM)
Since it has been moved to sctp_stream_outq_migrate on net-next,
to avoid the extra job when merging net-next to net, I will post
the fix for it after the merging is done.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
Commit d4d6fb5787 ("sctp: Try not to change a_rwnd when faking a
SACK from SHUTDOWN.") expected to use the peers old rwnd and add
our flight size to the a_rwnd. But with the wrong Endian, it may
not work as well as expected.
So fix it by converting to the right value.
Fixes: d4d6fb5787 ("sctp: Try not to change a_rwnd when faking a SACK from SHUTDOWN.")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian for the port when
coding transport rhashtable patches.
Fixes: 7fda702f93 ("sctp: use new rhlist interface on sctp transport rhashtable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings were found by running 'make C=2 M=net/sctp/'.
They are introduced by not aware of Endian when coding stream
reconf patches.
Since commit c0d8bab6ae ("sctp: add get and set sockopt for
reconf_enable") enabled stream reconf feature for users, the
Fixes tag below would use it.
Fixes: c0d8bab6ae ("sctp: add get and set sockopt for reconf_enable")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davide found the following script triggers a NULL pointer
dereference:
ip l a name eth0 type dummy
tc q a dev eth0 parent :1 handle 1: htb
This is because for a freshly created netdevice noop_qdisc
is attached and when passing 'parent :1', kernel actually
tries to match the major handle which is 0 and noop_qdisc
has handle 0 so is matched by mistake. Commit 69012ae425
tries to fix a similar bug but still misses this case.
Handle 0 is not a valid one, should be just skipped. In
fact, kernel uses it as TC_H_UNSPEC.
Fixes: 69012ae425 ("net: sched: fix handling of singleton qdiscs with qdisc_hash")
Fixes: 59cc1f61f0 ("net: sched:convert qdisc linked list to hashtable")
Reported-by: Davide Caratti <dcaratti@redhat.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cached routes should only be created by the system when receiving pmtu
discovery or ip redirect msg. Users should not be allowed to create
cached routes.
Furthermore, after the patch series to move cached routes into exception
table, user added cached routes will trigger the following warning in
fib6_add():
WARNING: CPU: 0 PID: 2985 at net/ipv6/ip6_fib.c:1137
fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 2985 Comm: syzkaller320388 Not tainted 4.14.0-rc3+ #74
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x417 kernel/panic.c:181
__warn+0x1c4/0x1d9 kernel/panic.c:542
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:178
do_trap_no_signal arch/x86/kernel/traps.c:212 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:261
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:298
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:311
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:fib6_add+0x20d9/0x2c10 net/ipv6/ip6_fib.c:1137
RSP: 0018:ffff8801cf09f6a0 EFLAGS: 00010297
RAX: ffff8801ce45e340 RBX: 1ffff10039e13eec RCX: ffff8801d749c814
RDX: 0000000000000000 RSI: ffff8801d749c700 RDI: ffff8801d749c780
RBP: ffff8801cf09fa08 R08: 0000000000000000 R09: ffff8801cf09f360
R10: ffff8801cf09f2d8 R11: 1ffff10039c8befb R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d749c700 R15: ffffffff860655c0
__ip6_ins_rt+0x6c/0x90 net/ipv6/route.c:1011
ip6_route_add+0x148/0x1a0 net/ipv6/route.c:2782
ipv6_route_ioctl+0x4d5/0x690 net/ipv6/route.c:3291
inet6_ioctl+0xef/0x1e0 net/ipv6/af_inet6.c:521
sock_do_ioctl+0x65/0xb0 net/socket.c:961
sock_ioctl+0x2c2/0x440 net/socket.c:1058
vfs_ioctl fs/ioctl.c:45 [inline]
do_vfs_ioctl+0x1b1/0x1530 fs/ioctl.c:685
SYSC_ioctl fs/ioctl.c:700 [inline]
SyS_ioctl+0x8f/0xc0 fs/ioctl.c:691
entry_SYSCALL_64_fastpath+0x1f/0xbe
So we fix this by failing the attemp to add cached routes from userspace
with returning EINVAL error.
Fixes: 2b760fcf5c ("ipv6: hook up exception table to store dst cache")
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when migrating sock to another one in sctp_sock_migrate(), it only
resets owner sk for the data in receive queues, not the chunks on out
queues.
It would cause that data chunks length on the sock is not consistent
with sk sk_wmem_alloc. When closing the sock or freeing these chunks,
the old sk would never be freed, and the new sock may crash due to
the overflow sk_wmem_alloc.
syzbot found this issue with this series:
r0 = socket$inet_sctp()
sendto$inet(r0)
listen(r0)
accept4(r0)
close(r0)
Although listen() should have returned error when one TCP-style socket
is in connecting (I may fix this one in another patch), it could also
be reproduced by peeling off an assoc.
This issue is there since very beginning.
This patch is to reset owner sk for the chunks on out queues so that
sk sk_wmem_alloc has correct value after accept one sock or peeloff
an assoc to one sock.
Note that when resetting owner sk for chunks on outqueue, it has to
sctp_clear_owner_w/skb_orphan chunks before changing assoc->base.sk
first and then sctp_set_owner_w them after changing assoc->base.sk,
due to that sctp_wfree and it's callees are using assoc->base.sk.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2017-10-27
This patchset is a proposal of how the Traffic Control subsystem can
be used to offload the configuration of the Credit Based Shaper
(defined in the IEEE 802.1Q-2014 Section 8.6.8.2) into supported
network devices.
As part of this work, we've assessed previous public discussions
related to TSN enabling: patches from Henrik Austad (Cisco), the
presentation from Eric Mann at Linux Plumbers 2012, patches from
Gangfeng Huang (National Instruments) and the current state of the
OpenAVNU project (https://github.com/AVnu/OpenAvnu/).
Overview
========
Time-sensitive Networking (TSN) is a set of standards that aim to
address resources availability for providing bandwidth reservation and
bounded latency on Ethernet based LANs. The proposal described here
aims to cover mainly what is needed to enable the following standards:
802.1Qat and 802.1Qav.
The initial target of this work is the Intel i210 NIC, but other
controllers' datasheet were also taken into account, like the Renesas
RZ/A1H RZ/A1M group and the Synopsis DesignWare Ethernet QoS
controller.
Proposal
========
Feature-wise, what is covered here is the configuration interfaces for
HW implementations of the Credit-Based shaper (CBS, 802.1Qav). CBS is
a per-queue shaper. Given that this feature is related to traffic
shaping, and that the traffic control subsystem already provides a
queueing discipline that offloads config into the device driver (i.e.
mqprio), designing a new qdisc for the specific purpose of offloading
the config for the CBS shaper seemed like a good fit.
For steering traffic into the correct queues, we use the socket option
SO_PRIORITY and then a mechanism to map priority to traffic classes /
Tx queues. The qdisc mqprio is currently used in our tests.
As for the CBS config interface, this patchset is proposing a new
qdisc called 'cbs'. Its 'tc' cmd line is:
$ tc qdisc add dev IFACE parent ID cbs locredit N hicredit M sendslope S \
idleslope I
Note that the parameters for this qdisc are the ones defined by the
802.1Q-2014 spec, so no hardware specific functionality is exposed here.
Per-stream shaping, as defined by IEEE 802.1Q-2014 Section 34.6.1, is
not yet covered by this proposal.
v2: Merged patch 6 of the original series into patch 4 based on feedback
from David Miller.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent additions to support multiple programs in cgroups impose
a strict requirement, "all yes is yes, any no is no". To enforce
this the infrastructure requires the 'no' return code, SK_DROP in
this case, to be 0.
To apply these rules to SK_SKB program types the sk_actions return
codes need to be adjusted.
This fix adds SK_PASS and makes 'SK_DROP = 0'. Finally, remove
SK_ABORTED to remove any chance that the API may allow aborted
program flows to be passed up the stack. This would be incorrect
behavior and allow programs to break existing policies.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SK_SKB program types use bpf_compute_data to store the end of the
packet data. However, bpf_compute_data assumes the cb is stored in the
qdisc layer format. But, for SK_SKB this is the wrong layer of the
stack for this type.
It happens to work (sort of!) because in most cases nothing happens
to be overwritten today. This is very fragile and error prone.
Fortunately, we have another hole in tcp_skb_cb we can use so lets
put the data_end value there.
Note, SK_SKB program types do not use data_meta, they are failed by
sk_skb_is_valid_access().
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pppol2tp_connect() initialises L2TP sessions after they've been exposed
to the rest of the system by l2tp_session_register(). This puts
sessions into transient states that are the source of several races, in
particular with session's deletion path.
This patch centralises the initialisation code into
pppol2tp_session_init(), which is called before the registration phase.
The only field that can't be set before session registration is the
pppol2tp socket pointer, which has already been converted to RCU. So
pppol2tp_connect() should now be race-free.
The session's .session_close() callback is now set before registration.
Therefore, it's always called when l2tp_core deletes the session, even
if it was created by pppol2tp_session_create() and hasn't been plugged
to a pppol2tp socket yet. That'd prevent session free because the extra
reference taken by pppol2tp_session_close() wouldn't be dropped by the
socket's ->sk_destruct() callback (pppol2tp_session_destruct()).
We could set .session_close() only while connecting a session to its
pppol2tp socket, or teach pppol2tp_session_close() to avoid grabbing a
reference when the session isn't connected, but that'd require adding
some form of synchronisation to be race free.
Instead of that, we can just let the pppol2tp socket hold a reference
on the session as soon as it starts depending on it (that is, in
pppol2tp_connect()). Then we don't need to utilise
pppol2tp_session_close() to hold a reference at the last moment to
prevent l2tp_core from dropping it.
When releasing the socket, pppol2tp_release() now deletes the session
using the standard l2tp_session_delete() function, instead of merely
removing it from hash tables. l2tp_session_delete() drops the reference
the sessions holds on itself, but also makes sure it doesn't remove a
session twice. So it can safely be called, even if l2tp_core already
tried, or is concurrently trying, to remove the session.
Finally, pppol2tp_session_destruct() drops the reference held by the
socket.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
pppol2tp_session_create() registers sessions that can't have their
corresponding socket initialised. This socket has to be created by
userspace, then connected to the session by pppol2tp_connect().
Therefore, we need to protect the pppol2tp socket pointer of L2TP
sessions, so that it can safely be updated when userspace is connecting
or closing the socket. This will eventually allow pppol2tp_connect()
to avoid generating transient states while initialising its parts of the
session.
To this end, this patch protects the pppol2tp socket pointer using RCU.
The pppol2tp socket pointer is still set in pppol2tp_connect(), but
only once we know the function isn't going to fail. It's eventually
reset by pppol2tp_release(), which now has to wait for a grace period
to elapse before it can drop the last reference on the socket. This
ensures that pppol2tp_session_get_sock() can safely grab a reference
on the socket, even after ps->sk is reset to NULL but before this
operation actually gets visible from pppol2tp_session_get_sock().
The rest is standard RCU conversion: pppol2tp_recv(), which already
runs in atomic context, is simply enclosed by rcu_read_lock() and
rcu_read_unlock(), while other functions are converted to use
pppol2tp_session_get_sock() followed by sock_put().
pppol2tp_session_setsockopt() is a special case. It used to retrieve
the pppol2tp socket from the L2TP session, which itself was retrieved
from the pppol2tp socket. Therefore we can just avoid dereferencing
ps->sk and directly use the original socket pointer instead.
With all users of ps->sk now handling NULL and concurrent updates, the
L2TP ->ref() and ->deref() callbacks aren't needed anymore. Therefore,
rather than converting pppol2tp_session_sock_hold() and
pppol2tp_session_sock_put(), we can just drop them.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sessions must be initialised before being made externally visible by
l2tp_session_register(). Otherwise the session may be concurrently
deleted before being initialised, which can confuse the deletion path
and eventually lead to kernel oops.
Therefore, we need to move l2tp_session_register() down in
l2tp_eth_create(), but also handle the intermediate step where only the
session or the netdevice has been registered.
We can't just call l2tp_session_register() in ->ndo_init() because
we'd have no way to properly undo this operation in ->ndo_uninit().
Instead, let's register the session and the netdevice in two different
steps and protect the session's device pointer with RCU.
And now that we allow the session's .dev field to be NULL, we don't
need to prevent the netdevice from being removed anymore. So we can
drop the dev_hold() and dev_put() calls in l2tp_eth_create() and
l2tp_eth_dev_uninit().
Fixes: d9e31d17ce ("l2tp: Add L2TP ethernet pseudowire support")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sessions created by l2tp_session_create() aren't fully initialised:
some pseudo-wire specific operations need to be done before making the
session usable. Therefore the PPP and Ethernet pseudo-wires continue
working on the returned l2tp session while it's already been exposed to
the rest of the system.
This can lead to various issues. In particular, the session may enter
the deletion process before having been fully initialised, which will
confuse the session removal code.
This patch moves session registration out of l2tp_session_create(), so
that callers can control when the session is exposed to the rest of the
system. This is done by the new l2tp_session_register() function.
Only pppol2tp_session_create() can be easily converted to avoid
modifying its session after registration (the debug message is dropped
in order to avoid the need for holding a reference on the session).
For pppol2tp_connect() and l2tp_eth_create()), more work is needed.
That'll be done in followup patches. For now, let's just register the
session right after its creation, like it was done before. The only
difference is that we can easily take a reference on the session before
registering it, so, at least, we're sure it's not going to be freed
while we're working on it.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This causes build failures:
In file included from net/ipv4/tcp_input.c:79:0:
./include/linux/unaligned/access_ok.h:7:28: error: redefinition of
'get_unaligned_le16'
In file included from ./include/asm-generic/unaligned.h:17:0,
from ./arch/arm/include/generated/asm/unaligned.h:1,
from net/ipv4/tcp_input.c:76:
./include/linux/unaligned/le_struct.h:6:19: note: previous definition
of 'get_unaligned_le16' was here
In file included from net/ipv4/tcp_input.c:79:0:
./include/linux/unaligned/access_ok.h:12:28: error: redefinition of
'get_unaligned_le32'
Plain "asm/access_ok.h", which is already included, is
sufficient.
Fixes: 60e2a77807 ("tcp: TCP experimental option for SMC")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch there was no way to tell if the vlan add operation
actually changed anything, thus we would always generate a notification
on adds. Let's make the notifications more precise and generate them
only if anything changed, so use the new bool parameter to signal that the
vlan was updated. We cannot return an error because there are valid use
cases that will be broken (e.g. overlapping range add) and also we can't
risk masking errors due to calls into drivers for vlan add which can
potentially return anything.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this patch we had cases that either sent notifications when there
were in fact no changes (e.g. non-existent vlan delete) or didn't send
notifications when there were changes (e.g. vlan add range with an error in
the middle, port flags change + vlan update error). This patch sends down
a boolean to the functions setlink/dellink use and if there is even a
single configuration change (port flag, vlan add/del, port state) then
we always send a notification. This is all done to keep backwards
compatibility with the opportunistic vlan delete, where one could
specify a vlan range that has missing vlans inside and still everything
in that range will be cleared, this is mostly used to clear the whole
vlan config with a single call, i.e. range 1-4094.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also remove an obsolete comment about TCP pacing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event tcp_mtu_probe() is sending a packet, we
want tp->tcp_mstamp being as accurate as possible.
This means we need to call tcp_mstamp_refresh() a bit earlier in
tcp_write_xmit().
Fixes: 385e20706f ("tcp: use tp->tcp_mstamp in output path")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
make use of the swap macro and remove unnecessary variable tmp_addr.
This makes the code easier to read and maintain.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new bindings (dsa2.c) and the old bindings (legacy.c) share two
helpers dsa_cpu_dsa_setup and dsa_cpu_dsa_destroy, used to register or
deregister a fixed PHY if a given port has a corresponding device node.
Unclutter the code by moving them into two new port.c helpers,
dsa_port_fixed_link_register_of and dsa_port_fixed_link_(un)register_of.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
