GPMC controller on AM335x-EVM has a NAND flash connected to it.
This patch updates following in am335x-evm.dts:
- adds nandflash specific pin-mux configs
- adds nand node as child of GPMC contoller, with information about
NAND flash interface, NAND partition table, ECC scheme, elm handle id.
- updates GPMC node for newer GPMC DT properties added in linux-3.10.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Gupta, Pekon <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
ELM hardware engine is used for locating bit-flips in NAND data
This patch is required for working of hardware based NAND ECC schemes
with DT support.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEP COM Module has an 512MB NAND flash memory.
Add a device node for this NAND and its partition layout.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEPv2 board has an 512MB NAND flash memory.
Add a device node for this NAND and its partition layout.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The IGEPv2 board has an SMSC LAN9221i ethernet chip connected to
the OMAP3 processor though the General-Purpose Memory Controller.
This patch adds a device node for the ethernet chip as a GPMC child
and all its dependencies (regulators, GPIO and pin muxs).
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
xdma_event_intr1.clkout2 pad can be used to source clock
from either 32K OSC or any of the PLL (except MPU) outputs.
On the existing AM335x based boards (EVM, EVM-SK and Bone),
this pad is used to feed the clock to audio codes.
So, this patch configures the pinmux to get clkout2 on the pad.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for UART0 device nodes in all
board specific DT files.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
With DT support, where naming convention is based on base-addr
and not id, so we should follow TRM/Spec numbering label.
This patch changes UART numbering as per TRM, as uart0-5.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Now gpio-leds driver is using devm_pinctrl_get_select_default()
api to set default pinmux configuration required for the
functionality of the driver, so this patch moves respective
pinctrl binding inside leds node.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add pin control binding for I2C device nodes in all
board specific DT files (as per current usage),
EVM: Both i2c0 and i2c1
EVM-SK and Bone: Only i2c0
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Matt Porter <mporter@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The carveouts that have been reserved for multimedia usecases
are not being used currently by any driver and so have been
cleaned up. Memory will be allocated runtime through CMA for
enabling the multimedia usecases.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical since
it fixes a problem where multiplatform kernels panic on all but prima2
hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=c555
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"These are a little later than I planned on since I got caught up with
handling merges for 3.11 most of the week.
Another week, another batch of fixes for arm-soc platforms.
Again, nothing controversial. A few more than would be ideal, but all
are valid fixes. In particular the prima2 panic patch is critical
since it fixes a problem where multiplatform kernels panic on all but
prima2 hardware."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: SAMSUNG: pm: Adjust for pinctrl- and DT-enabled platforms
ARM: prima2: fix incorrect panic usage
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
ARM: omap3: clock: fix wrong container_of in clock36xx.c
ARM: dts: OMAP5: Fix missing PWM capability to timer nodes
ARM: dts: omap4-panda|sdp: Fix mux for twl6030 IRQ pin and msecure line
ARM: dts: AM33xx: Fix properties on gpmc node
arm: omap2: fix AM33xx hwmod infos for UART2
ARM: OMAP3: Fix iva2_pwrdm settings for 3703
Pull powerpc fixes from Benjamin Herrenschmidt:
"So here are 3 fixes still for 3.10. Fixes are simple, bugs are nasty
(though not recent regressions, nasty enough) and all targeted at
stable"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix missing/delayed calls to irq_work
powerpc: Fix emulation of illegal instructions on PowerNV platform
powerpc: Fix stack overflow crash in resume_kernel when ftracing
When replaying interrupts (as a result of the interrupt occurring
while soft-disabled), in the case of the decrementer, we are exclusively
testing for a pending timer target. However we also use decrementer
interrupts to trigger the new "irq_work", which in this case would
be missed.
This change the logic to force a replay in both cases of a timer
boundary reached and a decrementer interrupt having actually occurred
while disabled. The former test is still useful to catch cases where
a CPU having been hard-disabled for a long time completely misses the
interrupt due to a decrementer rollover.
CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Normally, the kernel emulates a few instructions that are unimplemented
on some processors (e.g. the old dcba instruction), or privileged (e.g.
mfpvr). The emulation of unimplemented instructions is currently not
working on the PowerNV platform. The reason is that on these machines,
unimplemented and illegal instructions cause a hypervisor emulation
assist interrupt, rather than a program interrupt as on older CPUs.
Our vector for the emulation assist interrupt just calls
program_check_exception() directly, without setting the bit in SRR1
that indicates an illegal instruction interrupt. This fixes it by
making the emulation assist interrupt set that bit before calling
program_check_interrupt(). With this, old programs that use no-longer
implemented instructions such as dcba now work again.
CC: <stable@vger.kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It's possible for us to crash when running with ftrace enabled, eg:
Bad kernel stack pointer bffffd12 at c00000000000a454
cpu 0x3: Vector: 300 (Data Access) at [c00000000ffe3d40]
pc: c00000000000a454: resume_kernel+0x34/0x60
lr: c00000000000335c: performance_monitor_common+0x15c/0x180
sp: bffffd12
msr: 8000000000001032
dar: bffffd12
dsisr: 42000000
If we look at current's stack (paca->__current->stack) we see it is
equal to c0000002ecab0000. Our stack is 16K, and comparing to
paca->kstack (c0000002ecab3e30) we can see that we have overflowed our
kernel stack. This leads to us writing over our struct thread_info, and
in this case we have corrupted thread_info->flags and set
_TIF_EMULATE_STACK_STORE.
Dumping the stack we see:
3:mon> t c0000002ecab0000
[c0000002ecab0000] c00000000002131c .performance_monitor_exception+0x5c/0x70
[c0000002ecab0080] c00000000000335c performance_monitor_common+0x15c/0x180
--- Exception: f01 (Performance Monitor) at c0000000000fb2ec .trace_hardirqs_off+0x1c/0x30
[c0000002ecab0370] c00000000016fdb0 .trace_graph_entry+0xb0/0x280 (unreliable)
[c0000002ecab0410] c00000000003d038 .prepare_ftrace_return+0x98/0x130
[c0000002ecab04b0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
[c0000002ecab0520] c0000000000d6b58 .idle_cpu+0x18/0x90
[c0000002ecab05a0] c00000000000a934 .return_to_handler+0x0/0x34
[c0000002ecab0620] c00000000001e660 .timer_interrupt+0x160/0x300
[c0000002ecab06d0] c0000000000025dc decrementer_common+0x15c/0x180
--- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0
[c0000002ecab09c0] c0000000000fe044 .trace_hardirqs_on+0x14/0x30 (unreliable)
[c0000002ecab0fb0] c00000000016fe3c .trace_graph_entry+0x13c/0x280
[c0000002ecab1050] c00000000003d038 .prepare_ftrace_return+0x98/0x130
[c0000002ecab10f0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
[c0000002ecab1160] c0000000000161f0 .__ppc64_runlatch_on+0x10/0x40
[c0000002ecab11d0] c00000000000a934 .return_to_handler+0x0/0x34
--- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0
... and so on
__ppc64_runlatch_on() is called from RUNLATCH_ON in the exception entry
path. At that point the irq state is not consistent, ie. interrupts are
hard disabled (by the exception entry), but the paca soft-enabled flag
may be out of sync.
This leads to the local_irq_restore() in trace_graph_entry() actually
enabling interrupts, which we do not want. Because we have not yet
reprogrammed the decrementer we immediately take another decrementer
exception, and recurse.
The fix is twofold. Firstly make sure we call DISABLE_INTS before
calling RUNLATCH_ON. The badly named DISABLE_INTS actually reconciles
the irq state in the paca with the hardware, making it safe again to
call local_irq_save/restore().
Although that should be sufficient to fix the bug, we also mark the
runlatch routines as notrace. They are called very early in the
exception entry and we are asking for trouble tracing them. They are
also fairly uninteresting and tracing them just adds unnecessary
overhead.
[ This regression was introduced by fe1952fc0a
"powerpc: Rework runlatch code" by myself --BenH
]
CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This branch contains the following bug fixes:
- Fix locking vs. interrupts. Bug caught by lockdep checks
- Fix parsing of cpp #line directive output by dtc
- Fix 'make clean' for dtc temporary files.
There is also a commit that regenerates the dtc lexer and parser files
with Bison 2.5. The only purpose of this commit is to separate the
functional change in the dtc bug fix from the code generation change
caused by a different Bison version.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=om+W
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree bug fixes from Grant Likely:
"This branch contains the following bug fixes:
- Fix locking vs. interrupts. Bug caught by lockdep checks
- Fix parsing of cpp #line directive output by dtc
- Fix 'make clean' for dtc temporary files.
There is also a commit that regenerates the dtc lexer and parser files
with Bison 2.5. The only purpose of this commit is to separate the
functional change in the dtc bug fix from the code generation change
caused by a different Bison version"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
dtc: ensure #line directives don't consume data from the next line
dtc: Update generated files to output from Bison 2.5
of: Fix locking vs. interrupts
kbuild: make sure we clean up DTB temporary files
The OF code uses irqsafe locks everywhere except in a handful of functions
for no obvious reasons. Since the conversion from the old rwlocks, this
now triggers lockdep warnings when used at interrupt time. At least one
driver (ibmvscsi) seems to be doing that from softirq context.
This converts the few non-irqsafe locks into irqsafe ones, making them
consistent with the rest of the code.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Pull x86 fixes from Peter Anvin:
"Another set of fixes, the biggest bit of this is yet another tweak to
the UEFI anti-bricking code; apparently we finally got some feedback
from Samsung as to what makes at least their systems fail. This set
should actually fix the boot regressions that some other systems (e.g.
SGI) have exhibited.
Other than that, there is a patch to avoid a panic with particularly
unhappy memory layouts and two minor protocol fixes which may or may
not be manifest bugs"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix typo in kexec register clearing
x86, relocs: Move __vvar_page from S_ABS to S_REL
Modify UEFI anti-bricking code
x86: Fix adjust_range_size_mask calling position
Pull s390 fixes from Martin Schwidefsky:
"Three kvm related memory management fixes, a fix for show_trace, a fix
for early console output and a patch from Ben to help prevent compile
errors in regard to irq functions (or our lack thereof)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/pci: Implement IRQ functions if !PCI
s390/sclp: fix new line detection
s390/pgtable: make pgste lock an explicit barrier
s390/pgtable: Save pgste during modify_prot_start/commit
s390/dumpstack: fix address ranges for asynchronous and panic stack
s390/pgtable: Fix guest overindication for change bit
few users were reporting boot regressions in v3.9. This has now been
fixed with a more accurate "minimum storage requirement to avoid
bricking" value from Samsung (5K instead of 50%) and code to trigger
garbage collection when we near our limit - Matthew Garrett.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=TZuM
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' into x86/urgent
* More tweaking to the EFI variable anti-bricking algorithm. Quite a
few users were reporting boot regressions in v3.9. This has now been
fixed with a more accurate "minimum storage requirement to avoid
bricking" value from Samsung (5K instead of 50%) and code to trigger
garbage collection when we near our limit - Matthew Garrett.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fixes a typo in register clearing code. Thanks to PaX Team for fixing
this originally, and James Troup for pointing it out.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130605184718.GA8396@www.outflux.net
Cc: <stable@vger.kernel.org> v2.6.30+
Cc: PaX Team <pageexec@freemail.hu>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The __vvar_page relocation should actually be listed in S_REL instead
of S_ABS. Oddly, this didn't always cause things to break, presumably
because there are no users for relocation information on 64 bits yet.
[ hpa: Not for stable - new code in 3.10 ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130611185652.GA23674@www.outflux.net
Reported-by: Michael Davidson <md@google.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Pull MIPS fixes from Ralf Baechle:
"Resurrect Alchemy platforms by invoking the WAIT instructions with
interrupts enabled. This still leaves the race condition between
testing TIF_NEED_RESCHED and the WAIT instruction for Alchemy
platforms which need a different fix than other MIPS platforms. But
at least it gets MIPS platforms flying again.
There are also fixes for two build errors (CONFIG_FTRACE=y with
CONFIG_DYNAMIC_FTRACE=n) and CONFIG_VIRTUALIZATION without CONFIG_KVM"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: ftrace: Add missing CONFIG_DYNAMIC_FTRACE
MIPS: include: mmu_context.h: Replace VIRTUALIZATION with KVM
MIPS: Alchemy: fix wait function
- mvebu
- fix PCIe ranges property so NOR flash is visible
- kirkwood
- fix identification of 88f6282 so MPPs can be set correctly
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRtjVFAAoJEAi3KVZQDZAe4g4IAJcgufr2WBHJtGwVAGiSQLCr
gI3NjyfeJP98P7Bt/7ZyXBx5CmW3I6gVLN6Sctjpk01VISregbWv8Qos8iJx31hq
gqVmPJvaJy3dwHvq15rFMzNgsZGBTVV85wdnhppfeRTtt0nmREeJsLmgI1c5z0bw
u9BolnU1+sQn0S/TV/A4EZhyc18kAGzGqOKLOm3O4Ftrxncjq0idaSC5TOTDlA8Q
1D5bDbmaXyu7J1lqnYbbIsn9E4MTxfjbcrVnK1pEf7qhhtrmfJWiqLuay5plo/43
zMHefOc8rI74QUHxXuv6IS8QZcKKcfSJBpRCmxK6Ks74I9D6T9l7FxDb/2ckgJk=
=gHgq
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.10-4' of git://git.infradead.org/users/jcooper/linux into fixes
From Jason Cooper, mvebu fixes for v3.10 round 4:
- mvebu
- fix PCIe ranges property so NOR flash is visible
- kirkwood
- fix identification of 88f6282 so MPPs can be set correctly
* tag 'fixes-3.10-4' of git://git.infradead.org/users/jcooper/linux:
arm: mvebu: armada-xp-{gp,openblocks-ax3-4}: specify PCIe range
ARM: Kirkwood: handle mv88f6282 cpu in __kirkwood_variant().
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull kvm bugfixes from Gleb Natapov:
"There is one more fix for MIPS KVM ABI here, MIPS and PPC build
breakage fixes and a couple of PPC bug fixes"
* 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm/ppc/booke64: Fix lazy ee handling in kvmppc_handle_exit()
kvm/ppc/booke: Hold srcu lock when calling gfn functions
kvm/ppc/booke64: Disable e6500 support
kvm/ppc/booke64: Fix AltiVec interrupt numbers and build breakage
mips/kvm: Use KVM_REG_MIPS and proper size indicators for *_ONE_REG
kvm: Add definition of KVM_REG_MIPS
KVM: add kvm_para_available to asm-generic/kvm_para.h
EE is hard-disabled on entry to kvmppc_handle_exit(), so call
hard_irq_disable() so that PACA_IRQ_HARD_DIS is set, and soft_enabled
is unset.
Without this, we get warnings such as arch/powerpc/kernel/time.c:300,
and sometimes host kernel hangs.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
KVM core expects arch code to acquire the srcu lock when calling
gfn_to_memslot and similar functions.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
The previous patch made 64-bit booke KVM build again, but Altivec
support is still not complete, and we can't prevent the guest from
turning on Altivec (which can corrupt host state until state
save/restore is implemented). Disable e6500 on KVM until this is
fixed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Interrupt numbers defined for Book3E follows IVORs definition. Align
BOOKE_INTERRUPT_ALTIVEC_UNAVAIL and BOOKE_INTERRUPT_ALTIVEC_ASSIST to this
rule which also fixes the build breakage.
IVORs 32 and 33 are shared so reflect this in the interrupts naming.
This fixes a build break for 64-bit booke KVM.
Signed-off-by: Mihai Caraman <mihai.caraman@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This patch makes legacy code on suspend/resume path being executed
conditionally, on non-DT platforms only, to fix suspend/resume of
DT-enabled systems, for which the code is inappropriate.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[olof: add #include <linux/of.h>]
Signed-off-by: Olof Johansson <olof@lixom.net>
The API requires that the GET_ONE_REG and SET_ONE_REG ioctls have this
extra information encoded in the register identifiers.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
In prima2, some functions of checking DT is registered in initcall
level. If it doesn't match the compatible name of sirf, kernel
will panic. It blocks the usage of multiplatform on other verndor.
The error message is in below.
Knic - not syncing: unable to find compatible pwrc node in dtb
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-rc3-00006-gd7f26ea-dirty #86
[<c0013adc>] (unwind_backtrace+0x0/0xf8) from [<c0011430>] (show_stack+0x10/0x1)
[<c0011430>] (show_stack+0x10/0x14) from [<c026f724>] (panic+0x90/0x1e8)
[<c026f724>] (panic+0x90/0x1e8) from [<c03267fc>] (sirfsoc_of_pwrc_init+0x24/0x)
[<c03267fc>] (sirfsoc_of_pwrc_init+0x24/0x58) from [<c0320864>] (do_one_initcal)
[<c0320864>] (do_one_initcall+0x90/0x150) from [<c0320a20>] (kernel_init_freeab)
[<c0320a20>] (kernel_init_freeable+0xfc/0x1c4) from [<c026b9e8>] (kernel_init+0)
[<c026b9e8>] (kernel_init+0x8/0xe4) from [<c000e158>] (ret_from_fork+0x14/0x3c)
Signen-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch reworks the UEFI anti-bricking code, including an effective
reversion of cc5a080c and 31ff2f20. It turns out that calling
QueryVariableInfo() from boot services results in some firmware
implementations jumping to physical addresses even after entering virtual
mode, so until we have 1:1 mappings for UEFI runtime space this isn't
going to work so well.
Reverting these gets us back to the situation where we'd refuse to create
variables on some systems because they classify deleted variables as "used"
until the firmware triggers a garbage collection run, which they won't do
until they reach a lower threshold. This results in it being impossible to
install a bootloader, which is unhelpful.
Feedback from Samsung indicates that the firmware doesn't need more than
5KB of storage space for its own purposes, so that seems like a reasonable
threshold. However, there's still no guarantee that a platform will attempt
garbage collection merely because it drops below this threshold. It seems
that this is often only triggered if an attempt to write generates a
genuine EFI_OUT_OF_RESOURCES error. We can force that by attempting to
create a variable larger than the remaining space. This should fail, but if
it somehow succeeds we can then immediately delete it.
I've tested this on the UEFI machines I have available, but I don't have
a Samsung and so can't verify that it avoids the bricking problem.
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Lee, Chun-Y <jlee@suse.com> [ dummy variable cleanup ]
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
- xen/tmem stopped working after a certain combination of modprobe/swapon was used
- cpu online/offlining would trigger WARN_ON.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEcBAABAgAGBQJRtgQxAAoJEFjIrFwIi8fJ9QYH/ibEGBlKLfGzN4Apx6evBA68
l9CuLIpGCkPOiJLgVs10zY77Sg3f95bHFkJrwrEIDeTQ42joNKybsIp+qZCIS5CW
sAnzSd6Mb8jqQYJpgLl03+z3GdFzILTJ9e0zYTETbW2vfLpAETm87XWH+gjxDK0e
9I0kZX+Q3+2VWi5xv+UwWkYIOLbggLyKYajTHDwWNuC7vQgkJulCAbmjgN/NBv7A
xacvXdbEClIfZ5tvJJN0RggdEWo6WyTxyExfLPmpXFbHEvWDUX5LPEf8MhFY1ORK
U1C0BSV6YuLo350G5lY4I0R75ZEWLeUyVkZFnJIeGnUF1rP6OXEuVWTyeivPDBA=
=Fy36
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull xen fixes from Konrad Rzeszutek Wilk:
"Two bug-fixes for regressions:
- xen/tmem stopped working after a certain combination of
modprobe/swapon was used
- cpu online/offlining would trigger WARN_ON."
* tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/tmem: Don't over-write tmem_frontswap_poolid after tmem_frontswap_init set it.
xen/smp: Fixup NOHZ per cpu data when onlining an offline CPU.
arch_ftrace_update_code and ftrace_modify_all_code are only
available if CONFIG_DYNAMIC_FTRACE is selected.
Fixes the following build problem on MIPS randconfig:
arch/mips/kernel/ftrace.c: In function 'arch_ftrace_update_code':
arch/mips/kernel/ftrace.c:31:2: error: implicit declaration of function
'ftrace_modify_all_code' [-Werror=implicit-function-declaration]
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5435/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The kvm_* symbols are only available if KVM is selected.
Fixes the following linking problem on a randconfig:
arch/mips/built-in.o: In function `local_flush_tlb_mm':
(.text+0x18a94): undefined reference to `kvm_local_flush_tlb_all'
arch/mips/built-in.o: In function `local_flush_tlb_range':
(.text+0x18d0c): undefined reference to `kvm_local_flush_tlb_all'
kernel/built-in.o: In function `__schedule':
core.c:(.sched.text+0x2a00): undefined reference to `kvm_local_flush_tlb_all'
mm/built-in.o: In function `use_mm':
(.text+0x30214): undefined reference to `kvm_local_flush_tlb_all'
fs/built-in.o: In function `flush_old_exec':
(.text+0xf0a0): undefined reference to `kvm_local_flush_tlb_all'
make: *** [vmlinux] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5437/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only an interrupt can wake the core from 'wait', enable interrupts
locally before executing 'wait'.
[ralf@linux-mips.org: This leave the race between an interrupt that's
setting TIF_NEED_RESCHEd and entering the WAIT status. but at least it's
going to bring Alchemy back from the dead, so I'm going to apply this
patch.]
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/5408/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All architectures must implement IRQ functions. Since various
dependencies on !S390 were removed, there are various drivers that can
be selected but will fail to link. Provide a dummy implementation of
these functions for the !PCI case.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org # 3.9
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Pull powerpc fixes from Benjamin Herrenschmidt:
"This is purely regressions (though not all recent ones) or stable
material"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Partial revert of "Context switch more PMU related SPRs"
powerpc/perf: Fix deadlock caused by calling printk() in PMU exception
powerpc/hw_breakpoints: Add DABRX cpu feature to fix 32-bit regression
powerpc/power8: Update denormalization handler
powerpc/pseries: Simplify denormalization handler
powerpc/power8: Fix oprofile and perf
powerpc/eeh: Don't check RTAS token to get PE addr
powerpc/pci: Check the bus address instead of resource address in pcibios_fixup_resources
Pull ARM fixes from Russell King:
"The biggest two fixes are fixing a compilation error with the
decompressor, and a problem with our __my_cpu_offset implementation.
Other changes are very trivial and small, which seems to be the way
for most -rc stuff."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7747/1: pcpu: ensure __my_cpu_offset cannot be re-ordered across barrier()
ARM: 7750/1: update legacy CPU ID in decompressor cache support jump table
ARM: 7743/1: compressed/head.S: work around new binutils warning
ARM: 7742/1: topology: export cpu_topology
ARM: 7737/1: fix kernel decompressor compilation error with CONFIG_DEBUG_SEMIHOSTING
In commit 59affcd I added context switching of more PMU SPRs, because
they are potentially exposed to userspace on Power8. However despite me
being a smart arse in the commit message it's actually not correct. In
particular it interacts badly with a global perf record.
We will have to do something more complicated, but that will have to
wait for 3.11.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In commit bc09c21 "Fix finding overflowed PMC in interrupt" we added
a printk() to the PMU exception handler. Unfortunately that is not safe.
The problem is that the PMU exception may run even when interrupts are
soft disabled, aka NMI context. We do this so that we can profile parts
of the kernel that have interrupts soft-disabled.
But by calling printk() from the exception handler, we can potentially
deadlock in the printk code on logbuf_lock, eg:
[c00000038ba575c0] c000000000081928 .vprintk_emit+0xa8/0x540
[c00000038ba576a0] c0000000007bcde8 .printk+0x48/0x58
[c00000038ba57710] c000000000076504 .perf_event_interrupt+0x2d4/0x490
[c00000038ba57810] c00000000001f6f8 .performance_monitor_exception+0x48/0x60
[c00000038ba57880] c0000000000032cc performance_monitor_common+0x14c/0x180
--- Exception: f01 (Performance Monitor) at c0000000007b25d4 ._raw_spin_lock_irq
+0x64/0xc0
[c00000038ba57bf0] c00000000007ed90 .devkmsg_read+0xd0/0x5a0
[c00000038ba57d00] c0000000001c2934 .vfs_read+0xc4/0x1e0
[c00000038ba57d90] c0000000001c2cd8 .SyS_read+0x58/0xd0
[c00000038ba57e30] c000000000009d54 syscall_exit+0x0/0x98
--- Exception: c01 (System Call) at 00001fffffbf6f7c
SP (3ffff6d4de10) is in userspace
Fix it by making sure we only call printk() when we are not in NMI
context.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When introducing support for DABRX in 4474ef0, we broke older 32-bit CPUs
that don't have that register.
Some CPUs have a DABR but not DABRX. Configuration are:
- No 32bit CPUs have DABRX but some have DABR.
- POWER4+ and below have the DABR but no DABRX.
- 970 and POWER5 and above have DABR and DABRX.
- POWER8 has DAWR, hence no DABRX.
This introduces CPU_FTR_DABRX and sets it on appropriate CPUs. We use
the top 64 bits for CPU FTR bits since only 64 bit CPUs have this.
Processors that don't have the DABRX will still work as they will fall
back to software filtering these breakpoints via perf_exclude_event().
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reported-by: "Gorelik, Jacob (335F)" <jacob.gorelik@jpl.nasa.gov>
cc: stable@vger.kernel.org (v3.9 only)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
POWER8 can take a denormalisation exception on any VSX registers.
This does the extra 32 VSX registers we don't currently handle.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The following simplifies the denorm code by using macros to generate the long
stream of almost identical instructions.
This patch results in no changes to the output binary, but removes a lot of
lines of code.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In 2ac6f42 powerpc/cputable: Fix oprofile_cpu_type on power8
we broke all power8 hw events.
This reverts this change and uses oprofile_type instead. Perf now works
on POWER8 again and oprofile will revert to using timers on POWER8.
Kudos to mpe this fix.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
RTAS token "ibm,get-config-addr-info" or ibm,get-config-addr-info2"
are used to retrieve the PE address according to PCI address, which
made up of domain/bus/slot/function. If we don't have those 2 tokens,
the domain/bus/slot/function would be used as the address for EEH
RTAS operations. Some older f/w might not have those 2 tokens and
that blocks the EEH functionality to be initialized. It was introduced
by commit e2af155c ("powerpc/eeh: pseries platform EEH initialization").
The patch skips the check on those 2 tokens so we can bring up EEH
functionality successfully. And domain/bus/slot/function will be
used as address for EEH RTAS operations.
Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: Robert Knight <knight@princeton.edu>
Signed-off-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: Robert Knight <knight@princeton.edu>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If a BAR has the value of 0, we would assume that it is unset yet and
then mark the resource as unset and would reassign it later. But after
commit 6c5705fe (powerpc/PCI: get rid of device resource fixups)
the pcibios_fixup_resources is invoked after the bus address was
translated to linux resource. So the value of res->start is resource
address. And since the resource and bus address may be different, we
should translate it to the bus address before doing the check.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
