The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3, therefore we can use the standard 'regulator-ramp-delay'
property for those 2 regulators.
Note that the voltage ramp only works when the regulator is already
enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-for-MFD-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The AXP209 supports ramping up voltages on several regulators such as
DCDC2 and LDO3.
This patch adds preliminary support for the regulator-ramp-delay property
for these 2 regulators. Note that the voltage ramp only works when
regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V.
When turning on the regulator, no voltage ramp is performed in hardware.
What this means, is that if the bootloader brings up the voltage at 0.7 V,
the ramp delay property is properly applied. If however, the bootloader
leaves the power off, no ramp delay is applied when the power is
enabled by the regulator framework.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current axp20x names the ramping register 'scal' which probably
means scaling. Since the register really has nothing to do with
scaling, but really is the voltage ramp we rename it appropriately.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a regulator driver for the MCP16502 PMIC.
This drivers supports basic operations through the
regulator interface such as:
- setting/reading voltage
- setting/reading operating mode
- reading current status
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a maintainer for the MCP16502 PMIC
driver.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch describes the compatible and the device tree
bindings necessary for the MCP16502 PMIC.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add documentation for regulator modes and suspend states.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement shutdown method to make sure the PMIC will not enter the suspend
state when the system is shutdown.
This work is based on work done by Borris Brezillon on [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix line over 80 chars checkpatch.pl warning.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regulator supports a dedicated suspend mode.
Implement the appropriate ->set_suspend_xx() hooks, add support for
->set_mode(), and provide basic PM ops functionalities to setup the
regulator in a suspend state when the system is entering suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops,
fix checkpatch warning, adapt commit message, add LDO modes support,
move modes constants to active-semi,8945a-regulator.h, remove rdevs from
struct act8945a_pmic, add op_mode to act8945a_pmic]
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unlock expert registers for act8945a.
This is based on orginal work of Boris Brezillon at [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the Arizona LDO1 driver becomes
redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After making sure that the regulator core always take over
handling of the GPIO descriptors, the gpiod_put()
on the errorpath of the wm8994 driver becomes redundant.
Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
At the end of regulator_resolve_supply() we have historically turned
on our supply in some cases. This could be for one of two reasons:
1. If resolving supplies was happening before the call to
set_machine_constraints() we needed to predict if
set_machine_constraints() was going to turn the regulator on and we
needed to preemptively turn the supply on.
2. Maybe set_machine_constraints() happened before we could resolve
supplies (because we failed the first time to resolve) and thus we
might need to propagate an enable that already happened up to our
supply.
Historically regulator_resolve_supply() used _regulator_is_enabled()
to decide whether to turn on the supply.
Let's change things a little bit. Specifically:
1. Let's try to enable the supply and the regulator in the same place,
both in set_machine_constraints(). This means that we have exactly
the same logic for enabling the supply and the regulator.
2. Let's properly set use_count when we enable always-on or boot-on
regulators even for those that don't have supplies. The previous
commit 1fc12b0589 ("regulator: core: Avoid propagating to
supplies when possible") only did this right for regulators with
supplies.
3. Let's make it clear that the only time we need to enable the supply
in regulator_resolve_supply() is if the main regulator is currently
in use. By using use_count (like the rest of the code) to decide
if we're going to enable our supply we keep everything consistent.
Overall the new scheme should be cleaner and easier to reason about.
In addition to fixing regulator_summary to be more correct (because of
the more correct use_count), this change also has the effect of no
longer using _regulator_is_enabled() in this code path.
_regulator_is_enabled() could return an error code for some regulators
at bootup (like RPMh) that can't read their initial state. While one
can argue that the design of those regulators is sub-optimal, the new
logic sidesteps this brokenness. This fix in particular fixes
observed problems on Qualcomm sdm845 boards which use the
above-mentioned RPMh regulator. Those problems were made worse by
commit 1fc12b0589 ("regulator: core: Avoid propagating to supplies
when possible") because now we'd think at bootup that the SD
regulators were already enabled and we'd never try them again.
Fixes: 1fc12b0589 ("regulator: core: Avoid propagating to supplies when possible")
Reported-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S2MPS11 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the TPS65090 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the S5M8767 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The GPIO descriptors used by the DA9211 driver are retrieved
during probe() and it is really helpful to have those under
devres management because of all the errorpaths in the
intialization.
Using the new dev_gpiod_unhinge() call we can remove the
devres management of the descriptor right before handing
it over to the regulators core.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe path of this driver is a bit complex: sometimes the
GPIO descriptor is passed to the regulator core, sometimes
it is not.
To handle it in a simple way: stick with the devm_* resource
management and unhinge the GPIO descriptor devres handling
right before passing it to the regulator core, if we pass it
to the regulator core.
Fixes: e7d2be696f ("regulator: max8973: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a function named devm_gpiod_unhinge() that removes
the resource management from a GPIO descriptor.
I am not sure if this is the best anglosaxon name for the
function, no other managed resources have an equivalent
currently, but I chose "unhinge" as the closest intuitive
thing I could imagine that fits Rusty Russell's API design
criterions "the obvious use is the correct one" and
"the name tells you how to use it".
The idea came out of a remark from Mark Brown that it should
be possible to handle over management of a resource from
devres to the regulator core, and indeed we can do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a nonexeclusive GPIO descriptor using managed
resources, we should only add it to the list of managed
resources once: on the first user. Augment the
devm_gpiod_get_index() and devm_gpiod_get_from_of_node()
calls to account for this by checking if the descriptor
is already resource managed before we proceed to allocate
a new resource management struct.
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes gpiod_get_from_of_node() respect the
GPIOD_FLAGS_BIT_NONEXCLUSIVE flag which is especially
nice when getting regulator GPIOs right out of device
tree nodes.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get_from_of_node() rather than the devm_*
version so that the regulator core can handle the lifecycle
of these descriptors.
Fix up the errorpath so that we free this descriptor if
an error occurs in the callback. Rely on the regulator
core to deal with it after this point: a previous patch
fixed up the regulator core to properly dispose any
GPIO descriptors once you call regulator_register().
Fixes: 96392c3d8c ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function already exist inside gpiolib, we were just
reluctant to make it available to the kernel at large as
the devm_* seemed to be enough for anyone.
However we found out that regulators need to do their own
lifecycle/refcounting on GPIO descriptors and explicitly
call gpiod_put() when done with a descriptor, so export
this function so we can hand the refcounting over to the
regulator core for these descriptors after retrieveal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: d7a261c2d1 ("regulator: max8952: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: 2468f0d515 ("regulator: lp8788-ldo: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: b2d751b7f6 ("regulator: lm363x: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a GPIO descriptor is passed to the regulator_register()
function inside the config->ena_gpiod callers must be
sure that once they call this API the regulator core
owns that descriptor and will make sure to issue
gpiod_put() on it, no matter whether the call is
successful or not.
For device tree regulators, the regulator core will
automatically set up regulator init data from the device
tree when registering a regulator by calling
regulator_of_get_init_data() which in turn calls down to
the regulator driver's .of_parse_cb() callback.
This callback (in drivers such as for max77686) may also
choose to fill in the config->ena_gpiod field with a GPIO
descriptor.
Harden the errorpath of regulator_register() to
properly gpiod_put() any passed in cfg->ena_gpiod
or any gpiod coming from the device tree on any type
of error.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull networking fixes from David Miller:
"A decent batch of fixes here. I'd say about half are for problems that
have existed for a while, and half are for new regressions added in
the 4.20 merge window.
1) Fix 10G SFP phy module detection in mvpp2, from Baruch Siach.
2) Revert bogus emac driver change, from Benjamin Herrenschmidt.
3) Handle BPF exported data structure with pointers when building
32-bit userland, from Daniel Borkmann.
4) Memory leak fix in act_police, from Davide Caratti.
5) Check RX checksum offload in RX descriptors properly in aquantia
driver, from Dmitry Bogdanov.
6) SKB unlink fix in various spots, from Edward Cree.
7) ndo_dflt_fdb_dump() only works with ethernet, enforce this, from
Eric Dumazet.
8) Fix FID leak in mlxsw driver, from Ido Schimmel.
9) IOTLB locking fix in vhost, from Jean-Philippe Brucker.
10) Fix SKB truesize accounting in ipv4/ipv6/netfilter frag memory
limits otherwise namespace exit can hang. From Jiri Wiesner.
11) Address block parsing length fixes in x25 from Martin Schiller.
12) IRQ and ring accounting fixes in bnxt_en, from Michael Chan.
13) For tun interfaces, only iface delete works with rtnl ops, enforce
this by disallowing add. From Nicolas Dichtel.
14) Use after free in liquidio, from Pan Bian.
15) Fix SKB use after passing to netif_receive_skb(), from Prashant
Bhole.
16) Static key accounting and other fixes in XPS from Sabrina Dubroca.
17) Partially initialized flow key passed to ip6_route_output(), from
Shmulik Ladkani.
18) Fix RTNL deadlock during reset in ibmvnic driver, from Thomas
Falcon.
19) Several small TCP fixes (off-by-one on window probe abort, NULL
deref in tail loss probe, SNMP mis-estimations) from Yuchung
Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
net/sched: cls_flower: Reject duplicated rules also under skip_sw
bnxt_en: Fix _bnxt_get_max_rings() for 57500 chips.
bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.
bnxt_en: Keep track of reserved IRQs.
bnxt_en: Fix CNP CoS queue regression.
net/mlx4_core: Correctly set PFC param if global pause is turned off.
Revert "net/ibm/emac: wrong bit is used for STA control"
neighbour: Avoid writing before skb->head in neigh_hh_output()
ipv6: Check available headroom in ip6_xmit() even without options
tcp: lack of available data can also cause TSO defer
ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
mlxsw: spectrum_router: Relax GRE decap matching check
mlxsw: spectrum_switchdev: Avoid leaking FID's reference count
mlxsw: spectrum_nve: Remove easily triggerable warnings
ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
sctp: frag_point sanity check
tcp: fix NULL ref in tail loss probe
tcp: Do not underestimate rwnd_limited
net: use skb_list_del_init() to remove from RX sublists
...
Pull x86 fixes from Ingo Molnar:
"Three fixes: a boot parameter re-(re-)fix, a retpoline build artifact
fix and an LLVM workaround"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vdso: Drop implicit common-page-size linker flag
x86/build: Fix compiler support check for CONFIG_RETPOLINE
x86/boot: Clear RSDP address in boot_params for broken loaders
Pull kprobes fixes from Ingo Molnar:
"Two kprobes fixes: a blacklist fix and an instruction patching related
corruption fix"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kprobes/x86: Blacklist non-attachable interrupt functions
kprobes/x86: Fix instruction patching corruption when copying more than one RIP-relative instruction
Pull EFI fixes from Ingo Molnar:
"Two fixes: a large-system fix and an earlyprintk fix with certain
resolutions"
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/earlyprintk/efi: Fix infinite loop on some screen widths
x86/efi: Allocate e820 buffer before calling efi_exit_boot_service
Currently, duplicated rules are rejected only for skip_hw or "none",
hence allowing users to push duplicates into HW for no reason.
Use the flower tables to protect for that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reported-by: Chris Mi <chrism@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: Bug fixes.
The first patch fixes a regression on CoS queue setup, introduced
recently by the 57500 new chip support patches. The rest are
fixes related to ring and resource accounting on the new 57500 chips.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The CP rings are accounted differently on the new 57500 chips. There
must be enough CP rings for the sum of RX and TX rings on the new
chips. The current logic may be over-estimating the RX and TX rings.
The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips. We need to introduce a new
bnxt_nq_rings_in_use(). On legacy chips, the 2 functions are the
same and one will just call the other. On the new chips, they
refer to the 2 separate ring structures. The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.
On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector. To better unify this, add a resv_irqs
field to struct bnxt_hw_resc. On legacy chips, we initialize resv_irqs
with resv_cp_rings. On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to support the 57500 devices have created this
regression. The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not. Fix it by moving it to the right place right
after RDMA support is determined.
Fixes: 98f04cf0f1 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small driver fixes for 4.20-rc6.
There is a hyperv fix that for some reaon took forever to get into a
shape that could be applied to the tree properly, but resolves a
much reported issue. The others are some gnss patches, one a bugfix and
the two others updates to the MAINTAINERS file to properly match the
gnss files in the tree.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAz5RQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykKlACeKFk6Q9zC1gjaxNxNzV/RvCsMqNcAnjUcE7cw
KluPsfg8zZp8Jf5eQNHG
=hpqG
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 4.20-rc6.
There is a hyperv fix that for some reaon took forever to get into a
shape that could be applied to the tree properly, but resolves a much
reported issue. The others are some gnss patches, one a bugfix and the
two others updates to the MAINTAINERS file to properly match the gnss
files in the tree.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: exclude gnss from SIRFPRIMA2 regex matching
MAINTAINERS: add gnss scm tree
gnss: sirf: fix activation retry handling
Drivers: hv: vmbus: Offload the handling of channels to two workqueues
Here are two staging driver bugfixes for 4.20-rc6.
One is a revert of a previously incorrect patch that was merged a while
ago, and the other resolves a possible buffer overrun that was found by
code inspection.
Both of these have been in the linux-next tree with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAz4ng8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn/YACffYTp0y+UkyjJ/wTtrl15/ny2UdwAn3gErbci
tbvcc0bF5wvm0F1vKcU/
=OoII
-----END PGP SIGNATURE-----
Merge tag 'staging-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two staging driver bugfixes for 4.20-rc6.
One is a revert of a previously incorrect patch that was merged a
while ago, and the other resolves a possible buffer overrun that was
found by code inspection.
Both of these have been in the linux-next tree with no reported
issues"
* tag 'staging-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert commit ef9209b642 "staging: rtl8723bs: Fix indenting errors and an off-by-one mistake in core/rtw_mlme_ext.c"
staging: rtl8712: Fix possible buffer overrun
Here are three small tty driver fixes for 4.20-rc6
Nothing major, just some bug fixes for reported issues. Full details
are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAz36A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymYQgCgqA04cNFcelv38uoh9I1+AtOCRtEAnA64BAPe
HSAR9D0dbU2kb7vmIHg8
=vppK
-----END PGP SIGNATURE-----
Merge tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver fixes from Greg KH:
"Here are three small tty driver fixes for 4.20-rc6
Nothing major, just some bug fixes for reported issues. Full details
are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()
tty: serial: 8250_mtk: always resume the device in probe.
tty: do not set TTY_IO_ERROR flag if console port
Here are some small USB fixes for 4.20-rc6
The "largest" here are some xhci fixes for reported issues. Also here
is a USB core fix, some quirk additions, and a usb-serial fix which
required the export of one of the tty layer's functions to prevent code
duplication. The tty maintainer agreed with this change.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXAz3WA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl+mwCgox0WZiO3qfnpQsIrJ5gJFCTrcmMAoMBC5jDf
e81bwzu507PcqvEXh+rg
=giw6
-----END PGP SIGNATURE-----
Merge tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.20-rc6
The "largest" here are some xhci fixes for reported issues. Also here
is a USB core fix, some quirk additions, and a usb-serial fix which
required the export of one of the tty layer's functions to prevent
code duplication. The tty maintainer agreed with this change.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Prevent U1/U2 link pm states if exit latency is too long
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
USB: check usb_get_extra_descriptor for proper size
USB: serial: console: fix reported terminal settings
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
USB: Fix invalid-free bug in port_over_current_notify()
usb: appledisplay: Add 27" Apple Cinema Display
-----BEGIN PGP SIGNATURE-----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=wWgw
-----END PGP SIGNATURE-----
Merge tag '4.20-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Three small fixes: a fix for smb3 direct i/o, a fix for CIFS DFS for
stable and a minor cifs Kconfig fix"
* tag '4.20-rc5-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Avoid returning EBUSY to upper layer VFS
cifs: Fix separator when building path from dentry
cifs: In Kconfig CONFIG_CIFS_POSIX needs depends on legacy (insecure cifs)
* Fix the Xarray conversion of fsdax to properly handle
dax_lock_mapping_entry() in the presense of pmd entries.
* Fix inode destruction racing a new lock request.
-----BEGIN PGP SIGNATURE-----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=kUil
-----END PGP SIGNATURE-----
Merge tag 'dax-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull dax fixes from Dan Williams:
"The last of the known regression fixes and fallout from the Xarray
conversion of the filesystem-dax implementation.
On the path to debugging why the dax memory-failure injection test
started failing after the Xarray conversion a couple more fixes for
the dax_lock_mapping_entry(), now called dax_lock_page(), surfaced.
Those plus the bug that started the hunt are now addressed. These
patches have appeared in a -next release with no issues reported.
Note the touches to mm/memory-failure.c are just the conversion to the
new function signature for dax_lock_page().
Summary:
- Fix the Xarray conversion of fsdax to properly handle
dax_lock_mapping_entry() in the presense of pmd entries
- Fix inode destruction racing a new lock request"
* tag 'dax-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: Fix unlock mismatch with updated API
dax: Don't access a freed inode
dax: Check page->mapping isn't NULL
* Unless and until the core mm handles memory hotplug units smaller than
a section (128M), persistent memory namespaces must be padded to
section alignment. The libnvdimm core already handled section
collision with "System RAM", but some configurations overlap
independent "Persistent Memory" ranges within a section, so additional
padding injection is added for that case.
* The recent reworks of the ARS (address range scrub) state machine to
reduce the number of state flags inadvertantly missed a conversion of
acpi_nfit_ars_rescan() call sites. Fix the regression whereby
user-requested ARS results in a "short" scrub rather than a "long"
scrub.
* Fixup the unit tests to handle / test the 128M section alignment of
mocked test resources.
-----BEGIN PGP SIGNATURE-----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=85/B
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A regression fix for the Address Range Scrub implementation, yes
another one, and support for platforms that misalign persistent memory
relative to the Linux memory hotplug section constraint. Longer term,
support for sub-section memory hotplug would alleviate alignment
waste, but until then this hack allows a 'struct page' memmap to be
established for these misaligned memory regions.
These have all appeared in a -next release, and thanks to Patrick for
reporting and testing the alignment padding fix.
Summary:
- Unless and until the core mm handles memory hotplug units smaller
than a section (128M), persistent memory namespaces must be padded
to section alignment.
The libnvdimm core already handled section collision with "System
RAM", but some configurations overlap independent "Persistent
Memory" ranges within a section, so additional padding injection is
added for that case.
- The recent reworks of the ARS (address range scrub) state machine
to reduce the number of state flags inadvertantly missed a
conversion of acpi_nfit_ars_rescan() call sites. Fix the regression
whereby user-requested ARS results in a "short" scrub rather than a
"long" scrub.
- Fixup the unit tests to handle / test the 128M section alignment of
mocked test resources.
* tag 'libnvdimm-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
acpi/nfit: Fix user-initiated ARS to be "ARS-long" rather than "ARS-short"
libnvdimm, pfn: Pad pfn namespaces relative to other regions
tools/testing/nvdimm: Align test resources to 128M
