Clear pending exceptions when setting new register values. This avoids
spurious exceptions after restoring a vcpu state or after
reset-on-triple-fault.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The in-kernel PIT emulation ignores pending timers if operating under
mode 4, which for example DragonFlyBSD uses (and Plan9 too, apparently).
Mode 4 seems to be similar to one-shot mode, other than the fact that it
starts counting after the next CLK pulse once programmed, while mode 1
starts counting immediately, so add a FIXME to enhance precision.
Fixes sourceforge bug 1952988.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The recent changes allowing memory operands with lmsw and smsw left
lmsw with writeback enabled. Since lmsw has no oridinary destination
operand, the dst pointer was not initialized, resulting in an oops.
Close the hole by disabling writeback for lmsw.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch adds the delivery of INTERRUPT_FP_UNAVAIL exceptions to the guest.
It's needed if a guest uses ppc binaries using the Floating point instructions.
Signed-off-by: Christian Ehrhardt <ehrhardt@linux.vnet.ibm.com>
Acked-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reduces host CPU usage when the guest is idle. However, the guest must
set MSR[WE] in its idle loop, which Linux did not do until 2.6.26.
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Jerone Young <jyoung5@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
[aliguory: plug leak]
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Currently EPT level is 4 for both pae and x86_64. The patch remove the #ifdef
for alloc root_hpa and free root_hpa to support EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The function get_tdp_level() provided the number of tdp level for EPT and
NPT rather than the NPT specific macro.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Move some definitions to mmu.h in order to allow building common table
entries between EPT and non-EPT.
Signed-off-by: Sheng Yang <sheng.yang@intel.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Changeset 7f7c4072ea ("niu: Determine
the # of ports from the card's VPD data") caused maramba on-board
NIU ports to stop probing properly.
The old code had a fallback that would use a num_ports value of
4 if all the probing methods failed, but that was removed.
This restores the fallback of 4 ports, to get things working
again.
Bump driver version and release date.
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all device types need a wildcard at the end of their module
aliases. In particular, for i2c module aliases, the trailing wildcard
is not only unneeded, it could also cause the wrong driver to be
loaded.
As I2C devices have no IDs, i2c module aliases are simple, arbitrary
device names. For example:
$ /sbin/modinfo lm90
filename: /lib/modules/2.6.25-git18/kernel/drivers/hwmon/lm90.ko
author: Jean Delvare <khali@linux-fr.org>
description: LM90/ADM1032 driver
license: GPL
vermagic: 2.6.25-git18 mod_unload
depends: hwmon
alias: i2c:lm90*
alias: i2c:adm1032*
alias: i2c:lm99*
alias: i2c:lm86*
alias: i2c:max6657*
alias: i2c:adt7461*
alias: i2c:max6680*
$
This would cause trouble if one I2C chip name matches the beginning of
another I2C chip name and both chips are supported by different
drivers. For example, an i2c device named lm9042 would cause the lm90
driver to be loaded, while it doesn't support that device. This case
has yet to be seen in practice, but still, I'd like to fix it now. The
cleanest fix is to remove the trailing wildcard from i2c module aliases.
Here's a patch doing this.
Not all device type aliases need a trailing wildcard, in particular
the i2c aliases don't. Don't add a wildcard by default in do_table(),
instead let each device type handler add it if needed.
I have tested types acpi, dmi, eisa, i2c, ide, ieee1394, input, pci,
pcmcia, platform, pnp, scsi, serio, ssb and usb. Other types (ccw, of,
vio, parisc, sdio and virtio) are untested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Make blank functions use proper constant for unblanking.
Signed-off-by: Robert Reif <reif@earthlink.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2664ef44cf.
Ingo moved around where the softlockup dependency sits
so this change is no longer necessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
include/linux/skbuff.h says:
/* These elements must be at the end, see alloc_skb() for details. */
net/core/skbuff.c says:
* See comment in sk_buff definition, just before the 'tail' member
This patch contains my guess as to the actual reason rather than a
dead comment reference loop.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Robert Reif <reif@earthlink.net>
Replaced tcx_init_one with tcx_probe.
Fixed some checkpatch problems.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is lack of removing a class from the event queue while changing
from parent to leaf which can cause corruption of this rb tree. This
patch fixes a bug introduced by my patch: "sch_htb: turn intermediate
classes into leaves" commit: 160d5e10f8.
Many thanks to Jan 'yanek' Bortl for finding a way to reproduce this
rare bug and narrowing the test case, which made possible proper
diagnosing.
This patch is recommended for all kernels starting from 2.6.20.
Reported-and-tested-by: Jan 'yanek' Bortl <yanek@ya.bofh.cz>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A very small cleanup for mq_open.
We do not have to call set_close_on_exit if we create the file
descriptor right away with the flag set. We have a function for this
now. The resulting code is smaller and a tiny bit faster.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/hpa/linux-2.6-inttypes: (24 commits)
Make constants in kernel/timeconst.h fixed 64 bits
types: add C99-style constructors to <asm-generic/int-*.h>
xtensa: types: use <asm-generic/int-*.h> for the xtensa architecture
x86: types: use <asm-generic/int-*.h> for the x86 architecture
v850: types: use <asm-generic/int-*.h> for the v850 architecture
sparc64: types: use <asm-generic/int-*.h> for the sparc64 architecture
sparc: types: use <asm-generic/int-*.h> for the sparc architecture
sh: types: use <asm-generic/int-*.h> for the sh architecture
s390: types: use <asm-generic/int-*.h> for the s390 architecture
powerpc: types: use <asm-generic/int-*.h> for the powerpc architecture
parisc: types: use <asm-generic/int-*.h> for the parisc architecture
mn10300: types: use <asm-generic/int-*.h> for the mn10300 architecture
mips: types: use <asm-generic/int-*.h> for the mips architecture
m68k: types: use <asm-generic/int-*.h> for the m68k architecture
m32r: types: use <asm-generic/int-*.h> for the m32r architecture
ia64: types: use <asm-generic/int-*.h> for the ia64 architecture
h8300: types: use <asm-generic/int-*.h> for the h8300 architecture
frv: types: use <asm-generic/int-*.h> for the frv architecture
cris: types: use <asm-generic/int-*.h> for the cris architecture
blackfin: types: use <asm-generic/int-*.h> for the blackfin architecture
...
Many thanks to Martin for his years of hosting. The pci list has moved to
vger, along with what seems like the rest of the major Linux mailing lists.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/slab-2.6:
slub: #ifdef simplification
slabinfo: Support printout of the number of fallbacks
slub: Whitespace cleanup and use of strict_strtoul
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (47 commits)
rose: Wrong list_lock argument in rose_node seqops
netns: Fix reassembly timer to use the right namespace
netns: Fix device renaming for sysfs
bnx2: Update version to 1.7.5.
bnx2: Update RV2P firmware for 5709.
bnx2: Zero out context memory for 5709.
bnx2: Fix register test on 5709.
bnx2: Fix remote PHY initial link state.
bnx2: Refine remote PHY locking.
bridge: forwarding table information for >256 devices
tg3: Update version to 3.92
tg3: Add link state reporting to UMP firmware
tg3: Fix ethtool loopback test for 5761 BX devices
tg3: Fix 5761 NVRAM sizes
tg3: Use constant 500KHz MI clock on adapters with a CPMU
hci_usb.h: fix hard-to-trigger race
dccp: ccid2.c, ccid3.c use clamp(), clamp_t()
net: remove NR_CPUS arrays in net/core/dev.c
net: use get/put_unaligned_* helpers
bluetooth: use get/put_unaligned_* helpers
...
* git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Bolt in SLB entry for kernel stack on secondary cpus
[POWERPC] PS3: Update ps3_defconfig
[POWERPC] PS3: Remove unsupported wakeup sources
[POWERPC] PS3: Make ps3_virq_setup and ps3_virq_destroy static
[POWERPC] PS3: Add time include to lpm
[POWERPC] Fix slb.c compile warnings
[POWERPC] Xilinx: Fix compile warnings
[POWERPC] Squash build warning for print of resource_size_t in fsl_soc.c
[RAPIDIO] fix current kernel-doc notation
[POWERPC] 86xx: mpc8610_hpcd: add support for PCI Express x8 slot
Fix a potential issue in mpc52xx uart driver
[POWERPC] mpc5200: Allow for fixed speed MII configurations
[POWERPC] 86xx: Fix the wrong serial1 interrupt for 8610 board
There is no harm, when users can read the info and we ask often enough
during debugging for this kind of information.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
File permissions for
/sys/devices/system/clocksource/clocksource0/available_clocksource
are 600 which allows write access. But this is in fact a read only
file. So change permissions to 400.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The helper function hrtimer_callback_running() is used in
kernel/hrtimer.c as well as in the updated net/can/bcm.c which now
supports hrtimers. Moving the helper function to hrtimer.h removes the
duplicate definition in the C-files.
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In rose_node_start() as well as in rose_node_stop() __acquires() and
spin_lock_bh() were wrongly passing rose_neigh_list_lock instead of
rose_node_list_lock arguments.
Signed-off-by: Bernard Pidoux <f6bvp@amsat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This trivial fix retrieves the network namespace from frag queue
and use it to get the network device in the right namespace.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netdev is moved across namespaces with the
'dev_change_net_namespace' function, the 'device_rename' function is
used to fixup kobject and refresh the sysfs tree. The device_rename
function will call kobject_rename and this one will check if there is
an object with the same name and this is the case because we are
renaming the object with the same name.
The use of 'device_rename' seems for me wrong because we usually don't
rename it but just move it across namespaces. As we just want to do a
mini "netdev_[un]register", IMO the functions
'netdev_[un]register_kobject' should be used instead, like an usual
network device [un]registering.
This patch replace device_rename by netdev_unregister_kobject,
followed by netdev_register_kobject.
The netdev_register_kobject will call device_initialize and will raise
a warning indicating the device was already initialized. In order to
fix that, I split the device initialization into a separate function
and use it together with 'netdev_register_kobject' into
register_netdevice. So we can safely call 'netdev_register_kobject' in
'dev_change_net_namespace'.
This fix will allow to properly use the sysfs per namespace which is
coming from -mm tree.
Signed-off-by: Daniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new RV2P firmware fixes 2 issues:
1. The jumbo rx buffer page size is now configurable and set to the
proper PAGE_SIZE. Before, it was assumed to be always 4K.
2. Driver sometimes would crash when receiving jumbo packets mixed
with firmware management packets. This was caused by the old
firmware DMA'ing to the wrong address.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should zero out the context memory for 5709 before each reset. When
we resume after suspend for example, the memory may not be zero and the
chip may not function correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register BNX2_CTX_STATUS (0x1004) should be skipped on 5709 as it
contains reserved bits.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some remote PHY blade systems, the driver receives no initial link
interrupt. As a result, the GMII/MII MAC mode does not get setup properly.
To fix this problem, we add an initial poll of the link state after chip
reset.
With this change, the setting of the initial carrier state in the init
code can be eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2_set_remote_link() should be called under bp->phy_lock to protect
against concurrent polling and interrupt calls. This change is needed
by the next patch which will add one initial poll of the remote PHY
link status.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The forwarding table binary interface (my bad choice), only exposes
the port number of the first 8 bits. The bridge code was limited to
256 ports at the time, but now the kernel supports up 1024 ports, so
the upper bits are lost when doing:
brctl showmacs
The fix is to squeeze the extra bits into small hole left in data
structure, to maintain binary compatiablity.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.92.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All variants of the 5714, 5715, and 5780 offer a feature called the
"Universal Management Port". This feature is implemented in firmware
and is largely transparent to the driver, except...
It turns out that the UMP firmware needs to know the current status
of the link. Because the firmware cannot touch the PHY registers while
the driver is in control of the device, it needs the driver to report
link status changes through an additional handshaking mechanism.
Without this handshake, it has been observed in the field that the UMP
firmware will not operate correctly.
This patch implements the new handshake with the UMP firmware. Since
the handshake uses the same mechanism ASF heartbeats use, code was
added to detect and wait for completion of a pending previous event.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A CPMU related loopback test bug existed for AX revisions of the 5761.
While that errata has been fixed, the CPMU still slows down the core
clock too far to run the loopback test successfully. This patch
disables the CPMU LINK_SPEED mode just like we do with the AX
revisions of the 5761 and all revisions of the 5784.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
