The AB9540 variant of the AB8500 is basically close enough
to use the same driver. This adds the new registers and
deviations for this new chip variant.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This makes the AB8500 state struct contain the IRQ mask and
register offsets previously hard-coded so as to make room for
more AB8500 variants.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are currently four different versions of the AB8500
around: AB8500, AB8505, AB9540 and AB8540. Unfortunately:
- Some of the chips (AB8500, AB8505, AB9540) cannot read
the AB8500_REV_REG register but return errors
- Some of them have the same ID value in the hardware
register AB8500_REV_REV, for example the first versions
of AB8505 and AB9540 have 0xFF in this register -
just like the AB8500.
So we need to be able to enforce a certain version from
the platform. We do this by using the id of the platform
device that provides the read/write functions.
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Maxime Coquelin <maxime.coquelin@stericsson.com>
Signed-off-by: Alex Macro <alex.macro@stericsson.com>
Signed-off-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adds support for boards which have an STMPE device without the
interrupt pin connected.
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds an initial PRCMU register access API, which
for now should only be used for a very limited set of registers.
The idea about this API is that we split the PRCMU driver in
one part that deals with interaction with the PRCMU firmware
and one part that simply provide write accessors in the PRCMU
register range. The latter are just a collection of registers
exposed in the PRCMU register range for various purposes and
not related to the PRCMU firmware.
Currently we support some limited GPIO, SPI and UART settings
through this API.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This updates the operating point handling code by:
- Supporting the DDR OPP retention state.
- Supporting another low operating point named
APE_50_PARTLY_25_OPP
- Adding an interface to figure out if the sleep state change
was properly achieved.
Signed-off-by: Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This updates the clock handling in the DB8500 PRCMU driver with
the latest findings and API changes related to changes in the
backing firmware in the PRCMU.
- Add the necessary interfaces to get the frequencies of the
clocks and set the rate of some of the clocks.
- Add support for controlling the clocks PLLSOC0, PLLDSI,
DSI0, DSI1 and DSI escape clocks (DSInESCCLK).
- Correct the PLLSDI enable/disable sequence by using the
DSIPLL_CLAMPI bit.
After this we will have the interfaces and code to implement the
U8500 clock framework properly.
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This prefixes a number of accessor functions with db8500_* since
they are DB8500-specific and we need to move to this naming
scheme.
We also replace numerous instances of machine_is() with cpu_is()
which covers the right type of ASICs rather than entire machines
i.e. boards.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch exports a function that can be used to tell which
version of the DB8500 PRCMU firmware is available, and revamps the
firmware detection code a bit.
Reviewed-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This removes the U8400 legacy from PRCMU and cpufreq drivers.
This platform has no current in-kernel users.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MC13783 can be programmed to wait some clock cycles between the
touchscreen polarization and the resistance conversion. This is
needed to adjust for touchscreens with high capacitance between
plates.
Signed-off-by: Michael Thalmeier <michael.thalmeier@hale.at>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TPS65217 chip is a power management IC for Portable Navigation Systems
and Tablet Computing devices. It contains the following components:
- Regulators
- White LED
- USB battery charger
This patch adds support for tps65217 mfd device. At this time only
the regulator functionality is made available.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When an external capacitor is connected to MICBIAS2 on devices with
jack detection (which is not required but may be done in some systems)
then the loading may mean that better performance is obtained when
the microphone bias is enabled normally rather than using the low power
mode. Provide platform data allowing systems to indicate if they require
this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add genirq wakeup support for the ucb1x00 device. This allows an
attached gpio_keys driver to wakeup the system. Touchscreen is also
possible.
When there are no wakeup sources, ask the platform to assert the reset
signal to avoid any unexpected behaviour; this also puts the reset
signal at the right level when power is removed from the device.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the ucb1x00 driver to use genirq's interrupt services, rather
than its own private implementation. This allows a wider range of
drivers to use the GPIO interrupts (such as the gpio_keys driver)
without being aware of the UCB1x00's private IRQ system.
This prevents the UCB1x00 core driver from being built as a module,
so adjust the configuration to add that restriction.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The legacy driver suspend/resume methods are no longer used, so get rid
of them.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the ucb1x00-core driver to use dev_pm_ops rather than the legacy
members in the mcp driver.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert the ucb1x00 driver to use mutexes rather than the depreciated
semaphores for exclusive access to the ADC.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a way to handle the software controlled ucb1x00 reset signal
from the ucb1x00-core driver without having to code platform specifics
into these drivers.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch taken from 5dd7bf59e0 (ARM: sa11x0: Implement autoloading of codec
and codec pdata for mcp bus.) by Jochen Friedrich <jochen@scram.de>.
This adds just the codec data part of the patch.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The device tps65910/tps65911 supports the sleep
functionality in some of gpios. If gpio is configured
in output mode and sleep is enabled then during device
sleep state, the output of gpio becomes LOW regardless
of non-sleep output value.
Such gpio can be used to control regulator switch such
that output of regulator is off in device sleep state.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Store the last used mclk configuration for the PLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The dma_device_t variables are only ever written to by mcp-sa11x0 and
never read. As the old SA11x0 DMA support will be removed, remove
these so that it no longer depends on the old SA11x0 DMA definitions.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
host_unregister() gives us no chance between removing the device
and the mcp data structure being freed to access the data inbetween,
which drivers may need to do if they need to iounmap() pointers in
their private data structures.
Therefore, re-jig the interfaces, which are now, on creation:
mcp = mcp_host_alloc()
if (mcp) {
ret = mcp_host_add(mcp, data);
if (!ret)
mcp_host_free(mcp);
}
and on removal:
mcp_host_del(mcp);
... access mcp ...
mcp_host_free(mcp);
The free does the final put_device() on the struct device as one would
expect.
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for sleep controls of different regulator through
external inputs EN1, EN2 or EN3.
Each regulator's output will be active when its external
input is high and turns to OFF/Low power mode when its
external input is low.
The configuration parameters for sleep control is provided through
board specific platform data.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
mcp_priv() does unexpected things when passed a void pointer. Make it
a typed inline function, which ensures that it works correctly in
these cases.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This reverts commit 5dd7bf59e0.
Conflicts:
scripts/mod/file2alias.c
This change is wrong on many levels. First and foremost, it causes a
regression. On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:
ucb1x00 ID not found: 1005
0x1005 is a valid ID for the UCB1300 device.
Secondly, this patch is way over the top in terms of complexity. The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver. Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (526 commits)
ASoC: twl6040 - Add method to query optimum PDM_DL1 gain
ALSA: hda - Fix the lost power-setup of seconary pins after PM resume
ALSA: usb-audio: add Yamaha MOX6/MOX8 support
ALSA: virtuoso: add S/PDIF input support for all Xonars
ALSA: ice1724 - Support for ooAoo SQ210a
ALSA: ice1724 - Allow card info based on model only
ALSA: ice1724 - Create capture pcm only for ADC-enabled configurations
ALSA: hdspm - Provide unique driver id based on card serial
ASoC: Dynamically allocate the rtd device for a non-empty release()
ASoC: Fix recursive dependency due to select ATMEL_SSC in SND_ATMEL_SOC_SSC
ALSA: hda - Fix the detection of "Loopback Mixing" control for VIA codecs
ALSA: hda - Return the error from get_wcaps_type() for invalid NIDs
ALSA: hda - Use auto-parser for HP laptops with cx20459 codec
ALSA: asihpi - Fix potential Oops in snd_asihpi_cmode_info()
ALSA: hdsp - Fix potential Oops in snd_hdsp_info_pref_sync_ref()
ALSA: hda/cirrus - support for iMac12,2 model
ASoC: cx20442: add bias control over a platform provided regulator
ALSA: usb-audio - Avoid flood of frame-active debug messages
ALSA: snd-usb-us122l: Delete calls to preempt_disable
mfd: Put WM8994 into cache only mode when suspending
...
Fix up trivial conflicts in:
- arch/arm/mach-s3c64xx/mach-crag6410.c:
renamed speyside_wm8962 to tobermory, added littlemill right
next to it
- drivers/base/regmap/{regcache.c,regmap.c}:
duplicate diff that had already come in with other changes in
the regmap tree
* git://git.infradead.org/battery-2.6: (68 commits)
power_supply: Mark da9052 driver as broken
power_supply: Drop usage of nowarn variant of sysfs_create_link()
s3c_adc_battery: Average over more than one adc sample
power_supply: Add DA9052 battery driver
isp1704_charger: Fix missing check
jz4740-battery: Fix signedness bug
power_supply: Assume mains power by default
sbs-battery: Fix devicetree match table
ARM: rx51: Add bq27200 i2c board info
sbs-battery: Change power supply name
devicetree-bindings: Propagate bq20z75->sbs rename to dt bindings
devicetree-bindings: Add vendor entry for Smart Battery Systems
sbs-battery: Rename internals to new name
bq20z75: Rename to sbs-battery
wm97xx_battery: Use DEFINE_MUTEX() for work_lock
max8997_charger: Remove duplicate module.h
lp8727_charger: Some minor fixes for the header
lp8727_charger: Add header file
power_supply: Convert drivers/power/* to use module_platform_driver()
power_supply: Add "unknown" in power supply type
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (40 commits)
regulator: set constraints.apply_uV to 0 in of_get_fixed_voltage_config
regulator: max8925: fix enabled/disabled judgement mistake
regulator: add regulator_bulk_force_disable function
regulator: pass regulator_register of_node in fixed voltage driver
regulator: add regulator_force_disable() definition for !CONFIG_REGULATOR
regulator: Enable supply regulator if child rail is enabled.
regulator: mc13892: Convert to devm_kzalloc()
regulator: mc13783: Convert to devm_kzalloc()
regulator: Fix checking return value of create_regulator
regulator: Fix the error handling if create_regulator fails
regulator: Export regulator_is_supported_voltage()
regulator: mc13892: add device tree probe support
regulator: mc13892: remove the unnecessary prefix from regulator name
regulator: Convert wm831x regulator drivers to devm_kzalloc()
regulator: da9052: Staticize non-exported symbols
regulator: Replace kzalloc with devm_kzalloc and if-else with a switch-case for da9052-regulator
regulator: Update da9052-regulator for DT changes
regulator: DA9052/53 Regulator support
regulator: pass device_node to of_get_regulator_init_data()
regulator: If a single voltage is set with device tree then set apply_uV
...
Signed-off-by: Kevin Liu <kliu5@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
S5M series are pmic including mutiple functional devices.
It can support PMIC, RTC, Battery charger, codec.
This patch implement core driver for s5m series.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE801 is a GPIO expander. Registers for 801 are much different from other
variants. This patch adds support for STMPE801 in stmpe mfd driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
STMPE610 is very much like STMPE811, except the number of gpio pins, which is 8
in 811 and 6 in 610. This patch adds support for variant 610. STMPE610 will
share most of the code with STMPE811.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Few STMPE controller can have register interface over SPI or I2C. Current
implementation only supports I2C and all code is present in a single file
stmpe.c. It would be better to separate out I2C interface specific code from
controller specific code. Later SPI specific code can be added in a separate
file.
This patch separates out I2C and controller specific code into separate files,
making stmpe.c independent of I2C.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997 device does not support LED control function of it.
To enable MAX8997-LED driver, platform data and devices for LED are updated.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves all the header files related to the abx500 family into
a common include directory below mfd. From now on we place any
subchip header in that directory. Headers previously in e.g.
<linux/mfd/ab8500/gpio.h> get prefixed and are now e.g.
<linux/mfd/abx500/ab8500-gpio.h>. The top-level abstract interface
remains in <linux/mfd/abx500.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
struct wm8994 includes a mutex so we need to include mutex.h before we
declare it. All current users rely on this being done implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When the ADC is being prepared for a single or multiple channel reading,
the adc0 register is reconfigured without taking the lithium cell, charge
current and battery current reading enable bits into account. Which results
in clearing the bits.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Currently, MAX8997 device does not support MUIC function of it.
To add MAX8997 MUIC driver, header file should be updated.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Convert the 88pm860x normal bank register read/write to
use the register map API.
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
On many boards, stmpe is present as an separate device (not as part of SoC).
Here gpio lines are mostly used for getting interrupts. This patch adds in
support to handle irq over gpio pin.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It adds device tree probe support for mc13892-regulator driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DA9052/53 is a highly integrated PMIC subsystem with supply domain
flexibility to support wide range of high performance application.
It provides voltage regulators, GPIO controller, Touch Screen, RTC, Battery
control and other functionality.
This patch is functionally tested on Samsung SMDKV6410.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out the irq_chip implementation, substantially reducing the code
size for the driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
For later chip revisions the WM1811 GPIO6 register is always volatile so
store the device revision when initialising the driver and then check at
runtime if we're running on a newer device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
struct wm8994 includes a mutex so we need to include mutex.h before we
declare it. All current users rely on this being done implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
As part of this we provide information about the registers that exist in
the device to the regmap core, drop the small amount of cache that the
core had been using and let regmap do the sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Add a bunch of definitions for wm8994 registers that are not currently
used by software.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The power core infrastructure allow external power change
events to be passed to drivers what are listed in the
supplied_to call back field. Enable this feature by
allowing the supplied_to field to be passed to the driver.
This feature will enable drivers named in the supplied_to
field that have a external_power_changed callback to be
notified when power was been turned on or off.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
On brownstone rev 4 ac-insert detect is handled by vbus.
allow the platform code to configure the disabling of insert
by setting no_insert_detect.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Brownstone does not have temperature reading circuit hooked up.
This leads to spurious interrupts.
Allow the platform layer to indicate no temperature circuit
and do not activate interrupts if no temperature control is set
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.
Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain
With above expr, number of voltages that can be selected is
step value count * gain count
constant for gain count will be called VDD1_2_NUM_VOLT_COARSE
existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Create an array of fixed size for the platform to pass regulator
initalization data through.
Passing an array of pointers to init data also allows more flexible
definition of init data as well as prevents reading past the end of the
array should the platform define an incorrectly sized array.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the regulator defintions to the header so that platform board file
can use them to configure specific regulators.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Occasionally we may see an accessory reported before we have a stable
impedance for the accessory. If this happens then reread the status in
order to ensure that the handler can take the appropriate action for the
status change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-next' of git://git.infradead.org/users/sameo/mfd-2.6: (80 commits)
mfd: Fix missing abx500 header file updates
mfd: Add missing <linux/io.h> include to intel_msic
x86, mrst: add platform support for MSIC MFD driver
mfd: Expose TurnOnStatus in ab8500 sysfs
mfd: Remove support for early drop ab8500 chip
mfd: Add support for ab8500 v3.3
mfd: Add ab8500 interrupt disable hook
mfd: Convert db8500-prcmu panic() into pr_crit()
mfd: Refactor db8500-prcmu request_clock() function
mfd: Rename db8500-prcmu init function
mfd: Fix db5500-prcmu defines
mfd: db8500-prcmu voltage domain consumers additions
mfd: db8500-prcmu reset code retrieval
mfd: db8500-prcmu tweak for modem wakeup
mfd: Add db8500-pcmu watchdog accessor functions for watchdog
mfd: hwacc power state db8500-prcmu accessor
mfd: Add db8500-prcmu accessors for PLL and SGA clock
mfd: Move to the new db500 PRCMU API
mfd: Create a common interface for dbx500 PRCMU drivers
mfd: Initialize DB8500 PRCMU regs
...
Fix up trivial conflicts in
arch/arm/mach-imx/mach-mx31moboard.c
arch/arm/mach-omap2/board-omap3beagle.c
arch/arm/mach-u300/include/mach/irqs.h
drivers/mfd/wm831x-spi.c
I missed to include a patch adding the new silicon revision define
CUT3P3 and remove the retired CUT0 versions of AB8500. Also delete
the reference to the retired AB3550 from the header.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://opensource.wolfsonmicro.com/regulator: (22 commits)
regulator: Constify constraints name
regulator: Fix possible nullpointer dereference in regulator_enable()
regulator: gpio-regulator add dependency on GENERIC_GPIO
regulator: Add module.h include to gpio-regulator
regulator: Add driver for gpio-controlled regulators
regulator: remove duplicate REG_CTRL2 defines in tps65023
regulator: Clarify documentation for regulator-regulator supplies
regulator: Fix some bitrot in the machine driver documentation
regulator: tps65023: Added support for the similiar TPS65020 chip
regulator: tps65023: Setting correct core regulator for tps65021
regulator: tps65023: Set missing bit for update core-voltage
regulator: tps65023: Fixes i2c configuration issues
regulator: Add debugfs file showing the supply map table
regulator: tps6586x: add SMx slew rate setting
regulator: tps65023: Fixes i2c configuration issues
regulator: tps6507x: Remove num_voltages array
regulator: max8952: removed unused mutex.
regulator: fix regulator/consumer.h kernel-doc warning
regulator: Ensure enough enable time for max8649
regulator: 88pm8607: Fix off-by-one value range checking in the case of no id is matched
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'for-linus' of git://opensource.wolfsonmicro.com/regmap: (62 commits)
mfd: Enable rbtree cache for wm831x devices
regmap: Support some block operations on cached devices
regmap: Allow caches for devices with no defaults
regmap: Ensure rbtree syncs registers set to zero properly
regmap: Allow rbtree to cache zero default values
regmap: Warn on raw I/O as well as bulk reads that bypass cache
regmap: Return a sensible error code if we fail to read the cache
regmap: Use bsearch() to search the register defaults
regmap: Fix doc comment
regmap: Optimize the lookup path to use binary search
regmap: Ensure we scream if we enable cache bypass/only at the same time
regmap: Implement regcache_cache_bypass helper function
regmap: Save/restore the bypass state upon syncing
regmap: Lock the sync path, ensure we use the lockless _regmap_write()
regmap: Fix apostrophe usage
regmap: Make _regmap_write() global
regmap: Fix lock used for regcache_cache_only()
regmap: Grab the lock in regcache_cache_only()
regmap: Modify map->cache_bypass directly
regmap: Fix regcache_sync generic implementation
...
Now that we have a shared API between the DB8500 and DB5500
PRCMU's, switch to using this neutral API instead. We delete the
parts of db8500-prcmu.h that is now PRCMU-neutral, and calls will
be diverted to respective driver. Common registers are in
dbx500-prcmu-regs.h and common accessors and defines in
<linux/mfd/dbx500-prcmu.h> This way we get a a lot more
abstraction and code reuse.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a header file that contains the set of functions and
definitions that will be shared between the DB8500 and DB5500
PRCMU drivers.
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The AB3550 never passed the prototype stage. Instead it was used
as a precursor to AB5500 for testing basic building blocks used
in that chip, since they had large similarities. Since AB3550 will
not see the light of day in product form and since the prototypes
are no longer used, let's delete the driver and any references to
it.
Cc: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The analog baseband chip ab5500 is a multi functional chip
containing regulators, charging, gpio, USB and accessory detect.
It also contain various multimedia functionalities like digital
encoder and audio codec.
The core driver added with this patch provides register access via
i2c via PRCMU. Event handling implemented as irq_chip will come in
future patches since it depends on PRCMU functionality not yet
implemented.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for Intel MSIC chip found on Intel Medfield platforms. This
chip embeds several subdevices: audio, ADC, GPIO, power button, etc. The
driver creates platform device for each subdevice.
We also provide an MSIC register access API which should replace the more
generic SCU IPC interface currently used. Existing drivers can choose
whether they convert to this new API or stick with the SCU IPC interface.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In order to ease system integration provide a simulation of active high
IRQs on the GPIOs by polling the GPIO status when an IRQ is generated.
This isn't ideal on several fronts and will miss initially active IRQs in
the current implementation but it should work well for most cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds support for the power-on buttons of MC13783 PMIC.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that all in-tree users are fixed to use the more general mc13xxx API
the obsolete stuff can go away.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This is needed to convert the touch driver away from using struct mc13783.
Note this patch drops MC13783_ADC0_ADREFMODE. This is unused and doesn't
exist on mc13892.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
- Support wake-up from suspend-to-ram.
- Handle pending interrupt after a resume.
- If pdata->wakeup is enabled, by default, the device is assumed to be
capable of wakeup (the interrupt pin is connected to a wakeup-source GPIO)
and may wakeup the system (MAX8997 has a power button input pin).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In systems where the LDO enables are always driven (for example, being
connected to an always on supply rail or a GPIO which is driven by the
CPU even in suspend) then we can disable the pull downs on the LDO for
a small power savings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Refactor the GPADC interface to avoid bugs in calling code:
- ab8500_gpadc_[convert|read_raw|ad_to_voltage] clarifies
each functions use case, *convert wraps *read_raw, and we
can access raw ADC values properly.
- Renamed gpadc function arguments from "input" to "channel" to
clarify use, so we don't get confused again.
Signed-off-by: Kalle Komierowski <kalle.komierowski@stericsson.com>
Reviewed-by: Mattias Wallin <mattias.wallin@stericsson.com>
Reviewed-by: John Beckett <john.beckett@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Both Headset DAC need to be turned on/off at the same time before
any of the output drivers are enabled (HS Left/Right, Earpiece).
Move the HS DAC enable code to sequenced DAPM_SUPPLY, and attach
it to the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the client only interested, if any of the vibra channels enabled, or
if any of the channels are set to receive audio data via PDM.
This function targets mainly the vibra driver, so it can check if it is
allowed to execute effects ot not.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The vibra control register will be used from the ASoC codec driver as well.
In order to avoid latency issues caused by I2C read access, cache the two
control register within the core driver, so we do not need to reach out
to the chip to read it back.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The bits within the two control registers (for left and right channel)
are identical.
Use common names for the bits acros the two register.
Also add the missing definition for the path selection bit.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 is mostly register compatible with the WM8994 and WM8958,
providing a high performance audio hub CODEC in a small form factor
suitable for ultra compact system designs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811 is mostly register compatible with the WM8994 and WM8958,
providing a high performance audio hub CODEC in a small form factor
suitable for ultra compact system designs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Use one set of defines for the HS bits, since they are identical in both
control register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Software only shadow register to be used by the driver.
For example Earpiece path will need this shadow register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In systems where there is no hardware signal from the processor to the
PMIC to initiate the final power off sequence we must initiate the
shutdown with a register write to the PMIC. Support such systems in the
driver. Since this may prevent a full shutdown of the system platform
data is used to enable the feature.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There is no need to write to the vio registers at probe time, since most
them either read only, or shared with MFD or not used.
On the other hand it is a good idea to updated the ASICREV register in
the cache at this time.
After power up we need to restore some registers. Clean up the list to
contain only the registers we are going to restore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For client driver to use, if they need chip resvision information.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This needs to be an out of band value for the register and on this device
registers are 16 bit so we must shift left one to the 17th bit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Factor out the register read/write code to use the register map API. We
still need some wm831x specific code and locking in place to check that
the user key is handled correctly but only on the write side, reads are
not affected by the key.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
- Current implementation tests wrong value for setting
aat2870_bl->max_current.
- In the current implementation, we cannot differentiate between 2 cases:
a) if pdata->max_current is not set , or
b) pdata->max_current is set to AAT2870_CURRENT_0_45 (which is also 0).
Fix it by setting AAT2870_CURRENT_0_45 to be 1 and adjust the equation in
aat2870_brightness() accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Tested-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Later WM8994 devices implement a new DC servo readback mode with the
register used to access the offset moved to register 0x59. Implement
support for this and enable it on the appropriate devices.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Add mfd core driver for AnalogicTech AAT2870.
The AAT2870 is communication through I2C and contains backlight and
regulator components.
Signed-off-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Generating kerneldoc for STMPE result in warnings, so fix this by
adding missing documentation.
Signed-off-by: Om Prakash <omprakash.pal@stericsson.com>
Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65910_irq_exit() cleanup function was generating a warning from
sparse due to the lack of a prototype. This wasn't causing GCC warnings
as the driver wasn't cleaning up its IRQs on exit at all so there was no
use of an unprototyped function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a previously undefined test register and removed a
number of double-defined accessory detect registers (they are
already defined higher up in the file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
TPS65912 has five GPIOs that can be configured for different
purposes.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This module controls the interrupt handling for the tps65912.
The interrupt sources can be the following:
- GPIO
- PWRON signal
- PWRHOLD signal
- Temperature detection
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The tps65912 chip is a power management IC. It contains the following
components:
- Regulators
- GPIO controller
The core driver is registered as a platform driver, it provides communication
through I2C and SPI interfaces.
Signed-off-by: Margarita Olaya Cabrera <magi@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x AUXADC hardware can schedule multiple conversions at once,
allowing higher performance when more than one source is in use as we
can have the hardware start new conversions without having to wait for
a register write.
Take advantage of this in the interrupt driven case, maintaining a list of
callers that are waiting for AUXADC conversions and completing them all
simultaneously. The external interface of the AUXADC is not changed so
there will be limited use of the feature immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ensure that there's no possibility of loosing an AUXADC interrupt by reading
the conversion result in the IRQ handler when using interrupts. Otherwise
it's possible that under very heavy load a new conversion could be initiated
before the acknowledgement for a previous interrupt has happened.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Use irq_allocate_desc() to get the IRQ range, which turns into a noop on
non-sparse systems. Since all existing users are non-sparse there should
be no compatibility issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow platform data to flag the touchscreen as disabled so that if the
touch driver is built in we don't end up causing lots of work by spuriously
detecting touchscreen activity on systems where it isn't in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The WM831x IRQ set_type() operation is doing a direct register write when
called but since set_type() is called with the bus lock held this isn't
legal and could cause deadlocks in the IRQ core.
Fix this by posting the updates into an array and syncing in the
bus_sync_unlock() callback.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* git://git.infradead.org/battery-2.6:
gpio-charger: Fix checking return value of request_any_context_irq
power_supply: MAX17042: Support additional properties
max8903_charger: Allow platform data to be __initdata
power_supply: Add charger driver for MAX8998/LP3974
power_supply: Add charger driver for MAX8997/8966
max17042_battery: Remove obsolete cleanup for clientdata
twl4030_charger: Fix warnings
wm831x_power: Support multiple instances
wm831x_backup: Support multiple instances
apm_power: Fix style error in macros
s3c_adc_battery: Fix annotation for s3c_adc_battery_probe()
bq20z75: Enable detection after registering
bq20z75: Add support for external notification
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* Merge akpm patch series: (122 commits)
drivers/connector/cn_proc.c: remove unused local
Documentation/SubmitChecklist: add RCU debug config options
reiserfs: use hweight_long()
reiserfs: use proper little-endian bitops
pnpacpi: register disabled resources
drivers/rtc/rtc-tegra.c: properly initialize spinlock
drivers/rtc/rtc-twl.c: check return value of twl_rtc_write_u8() in twl_rtc_set_time()
drivers/rtc: add support for Qualcomm PMIC8xxx RTC
drivers/rtc/rtc-s3c.c: support clock gating
drivers/rtc/rtc-mpc5121.c: add support for RTC on MPC5200
init: skip calibration delay if previously done
misc/eeprom: add eeprom access driver for digsy_mtc board
misc/eeprom: add driver for microwire 93xx46 EEPROMs
checkpatch.pl: update $logFunctions
checkpatch: make utf-8 test --strict
checkpatch.pl: add ability to ignore various messages
checkpatch: add a "prefer __aligned" check
checkpatch: validate signature styles and To: and Cc: lines
checkpatch: add __rcu as a sparse modifier
checkpatch: suggest using min_t or max_t
...
Did this as a merge because of (trivial) conflicts in
- Documentation/feature-removal-schedule.txt
- arch/xtensa/include/asm/uaccess.h
that were just easier to fix up in the merge than in the patch series.
Add support for PMIC8xxx based RTC. PMIC8xxx is Qualcomm's power
management IC that internally houses an RTC module. This driver
communicates with the PMIC module over SSBI bus.
[akpm@linux-foundation.org: cosmetic tweaks]
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
All these are instances of
#define NAME value;
or
#define NAME(params_opt) value;
These of course fail to build when used in contexts like
if(foo $OP NAME)
while(bar $OP NAME)
and may silently generate the wrong code in contexts such as
foo = NAME + 1; /* foo = value; + 1; */
bar = NAME - 1; /* bar = value; - 1; */
baz = NAME & quux; /* baz = value; & quux; */
Reported on comp.lang.c,
Message-ID: <ab0d55fe-25e5-482b-811e-c475aa6065c3@c29g2000yqd.googlegroups.com>
Initial analysis of the dangers provided by Keith Thompson in that thread.
There are many more instances of more complicated macros having unnecessary
trailing semicolons, but this pile seems to be all of the cases of simple
values suffering from the problem. (Thus things that are likely to be found
in one of the contexts above, more complicated ones aren't.)
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Some controllers require waiting for the bus to become idle
before writing to some registers. I have implemented this
by adding a hook to sd_ctrl_write16() and implementing
a hook for SDHI which waits for the bus to become idle.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:
: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor chip - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK. I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.
This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves. Unfortunately,
this is not always the case. The sleep is restored but as a parameter to
the probe function in the pdata.
[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Jean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch supports power supply APIs for MAX8998/LP3974.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
MAX8997/8966 chip is a multi-function device which includes
PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery charging control.
The driver for it is located at drivers/mfd.
This patch supports battery charging control of MAX8997/8966 chip and
provides power supply class information to userspace.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
There is no need to have two different types for
tracking the selected PLL.
Use only the defines, when dealing with the PLLs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Remove the twl6040_request_irq/free_irq inline functions,
and use direct calls instead in the core driver to
register the threaded irq.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
TWL6040 IC provides analog high-end audio codec functions for
handset applications. It contains several audio analog inputs
and outputs as well as vibrator support. It's connected to the
host processor via PDM interface for audio data communication.
The audio modules are controlled by internal registers that
can be accessed by I2C and PDM interface.
TWL6040 MFD will be registered as a child of TWL-CORE, and will
have two children of its own: twl6040-codec and twl6040-vibra.
This driver is based on TWL4030 and WM8350 MFD drivers.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Rename the driver, and header file from twl4030-codec to
twl4030-audio.
To avoid breakage change depending drivers at the same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
This driver adds functionality to the tps65911 chip driver.
Two of the comparators are configurable by software and measures
VCCS voltage to detect high or low voltage scenarios.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
GPIO 1 to 8 are added for TPS65911 chip version. The gpio driver
now handles more than one gpio lines. Subsequent versions of the
chip family can add new GPIO lines with minimal driver changes.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS65911 adds new interrupt sources, as well as two new registers
to handle them, one for interrupt status and one for interrupt
masking. The added irqs are:
-VMBCH2 - Low and High threshold
-GPIO1-8 - Rising and falling edge detection
-WTCHDG - Watchdog interrupt
-PWRDN - PWRDN reset interrupt
The code should handle these new registers only when the chip
version is TPS65911.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The tps65911 chip introduces new features, including changes in
the regulator module.
- VDD1 and VDD2 remain unchanged.
- VDD3 is now named VDDCTRL and has a wider voltage range.
- LDOs are now named LDO1...8 and voltage ranges are sequential,
making LDOs easier to handle.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The TPS65911 is the next generation of the TPS65910 family of
PMIC chips. It adds a few features:
- Watchdog Timer
- PWM & LED generators
- Comparators for system control status
It also adds a set of Interrupts and GPIOs, among other things.
The driver exports a function to identify between different
versions of the tps65910 family, allowing other modules to
identify the capabilities of the current chip.
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In current implementation, the original macro implementation assumes the caller
pass the parameter starting from 1 (to match the register names in datasheet).
Thus we have unneeded plus one then minus one operations
when using MAX8997_REG_BUCK1DVS/MAX8997_REG_BUCK2DVS/MAX8997_REG_BUCK5DVS macros.
This patch removes these macros to avoid unneeded plus one then minus one operations
without reducing readability.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The regulator module consists of 3 DCDCs and 8 LDOs. The output
voltages are configurable and are meant to supply power to the
main processor and other components
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This module controls the interrupt handling for the tps chip. The
interrupt sources are the following:
- GPIO falling/rising edge detection
- Battery voltage below/above threshold
- PWRON signal
- PWRHOLD signal
- Temperature detection
- RTC alarm and periodic event
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
TPS65910 has one configurable GPIO that can be used for several
purposes. Subsequent versions of the TPS chip support more than
one GPIO.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The TPS65910 chip is a power management IC for multimedia and handheld
devices. It contains the following components:
- Regulators
- GPIO controller
- RTC
The tps65910 core driver is registered as a platform driver and provides
communication through I2C with the host device for the different
components.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The size of the TC6380AF SD Host Controller Configuration area is 0x200 bytes (assuming registers are aligned on 32-bit boundaries), not 0x400 bytes. Source: Toshiba TC6380AF Specification sections 4.2 and 4.3.1
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add LED support for the HTC ASIC3. Underlying support is provided by the mfd/asic3 and leds/leds-asic3 drivers. An example configuration is provided by the pxa/hx4700 platform.
Signed-off-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Since functionality in MFD cells may need to be adjusted according to
chip revision, let's enumerate them and keep track of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the irq controller in Qualcomm 8xxx pmic. The 8xxx
interrupt controller provides control for gpio and mpp configured as
interrupts in addition to other subdevice interrupts. The interrupt
controller also provides a way to read the real time status of an
interrupt. This real time status is the only way one can get the
input values of gpio and mpp lines.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the Qualcomm PM8921 PMIC chip. The core driver
will communicate with the PMIC chip via the MSM SSBI bus.
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow the GPIO mode of WM831x devices to be configured using platform data.
Users may provide a table of GPIO register values in gpio_defaults[]. In
order to allow 0 to be set explicitly out of range values are accepted and
masked off, with a WM831X_GPIO_CONFIGURE define provided to set an out of
range value.
This can be used to configure higher numbered GPIOs or override values set
in OTP for GPIOs configured using OTP.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The last user was removed in the merge window.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Cell pointers are passed through device->mfd_cell and platform data
is passed through the MFD cell platform_data pointer.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With the addition of a platform device mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the sub drivers
MFD agnostic. This is mostly needed for non MFD aware sub drivers.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Now that we have a way to pass MFD cells down to the sub drivers,
we can gradually get rid of mfd_data by putting the platform pointer
back in place.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
The TMIO MMC controller cannot be powered off to save power, when no
card is plugged in, because then it will not be able to detect a new
card-insertion event. On some implementations, however, it is
possible to switch to using another source to detect card insertion.
This patch adds support for such implementations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds the DB5500 PRCMU driver. Right now this one is pretty
restricted in functionality, exposing a simple interface to send
I2C messages.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This updates the DB8500 PRCMU driver to the latest version
available internally. Nominally we would update the dependent
CPUfreq driver at the same time but since that is being moved
around in this patch set we postpone that by simply deactivating
it for the time being.
This is a snapshot of the current PRCMU firmware API as it looks
right now. The PRCMU firmware is still subject to change. This
also updates the CPUfreq driver to a newer version that will
utilize the new API.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mattias Nilsson <mattias.i.nilsson@stericsson.com>
Signed-off-by: Martin Persson <martin.persson@stericsson.com>
Signed-off-by: Per Fransson <per.xx.fransson@stericsson.com>
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Sebastien Rault <sebastien.rault@stericsson.com>
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have decided that this function arbiter fits better in the MFD
subsystem. Since we need to concatenate the split header files we move
it basically like this:
mv mach-ux500/prcmu-db8500.c drivers/mfd/db8500-prcmu.c
mv mach-ux500/include/mach/prcmu-defs.h include/linux/mfd/db8500-prcmu.h
mv mach-ux500/include/mach/prcmu-regs.h drivers/mfd/db8500-prcmu-regs.h
mach-ux500/include/mach/prcmu.h >> include/linux/mfd/db8500-prcmu.h
rm arch/arm/mach-ux500/include/mach/prcmu.h
Then we update different #include statements and Makefile orders etc
to make the PRCMU driver compile, link and boot in the new place
without really changing any code.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wm831x-ts - move BTN_TOUCH reporting to data transfer
Input: wm831x-ts - allow IRQ flags to be specified
Input: wm831x-ts - fix races with IRQ management
This allows maximum flexibility for configuring the direct GPIO based
interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In order for MFD drivers to fetch their cell pointer but also their
platform data one, an mfd cell pointer is added to the platform_device
structure.
That allows all MFD sub devices drivers to be MFD agnostic, unless
they really need to access their MFD cell data. Most of them don't,
especially the ones for IPs used by both MFD and non MFD SoCs.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg KH <gregkh@suse.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (26 commits)
mmc: SDHI should depend on SUPERH || ARCH_SHMOBILE
mmc: tmio_mmc: Move some defines into a shared header
mmc: tmio: support aggressive clock gating
mmc: tmio: fix power-mode interpretation
mmc: tmio: remove work-around for unmasked SDIO interrupts
sh: fix SDHI IO address-range
ARM: mach-shmobile: fix SDHI IO address-range
mmc: tmio: only access registers above 0xff, if available
mfd: remove now redundant sh_mobile_sdhi.h header
sh: convert boards to use linux/mmc/sh_mobile_sdhi.h
ARM: mach-shmobile: convert boards to use linux/mmc/sh_mobile_sdhi.h
mmc: tmio: convert the SDHI MMC driver from MFD to a platform driver
sh: ecovec: use the CONFIG_MMC_TMIO symbols instead of MFD
mmc: tmio: split core functionality, DMA and MFD glue
mmc: tmio: use PIO for short transfers
mmc: tmio-mmc: Improve DMA stability on sh-mobile
mmc: fix mmc_app_send_scr() for dma transfer
mmc: sdhci-esdhc: enable esdhc on imx53
mmc: sdhci-esdhc: use writel/readl as general APIs
mmc: sdhci: add the abort CMDTYPE bits definition
...
To get rid of port expanders, the free GPIOs of ab8500
can be used. There are 42 GPIO pins. Out of which 16
are interrupt capable.This patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[Renamed header file as per MFD structure]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
regulator: fix tps6524x section mismatch
regulator: Remove more wm831x-specific IRQ operations
regulator: add ab8500 enable and raise time delays
regulator: provide consumer interface for fall/rise time
regulator: add set_voltage_time_sel infrastructure
regulator: initialization for ab8500 regulators
regulator: add support for USB voltage regulator
regulator: switch the ab3100 to use enable_time()
Regulator: add suspend-finish API for regulator core.
regulator: fix typo in Kconfig
regulator: Convert WM831x regulators to genirq
regulator: If we fail when setting up a supply say which supply
This patch enables IRQ handling for MAX8997/8966 chips.
Please note that Fuel-Gauge-related IRQs are not implemented in this
initial release. The fuel gauge module in MAX8997 is identical to
MAX17042, which is already in Linux kernel. In order to use the
already-existing MAX17042 driver for fuel gauge module in MAX8997, the
main interrupt handler of MAX8997 should relay related interrupts to
MAX17042 driver. However, in order to do this, we need to modify
MAX17042 driver as well because MAX17042 driver does not have any
interrupt handlers for now. We are not going to implement this in this
initial release as it is not crucial in basic operations of MAX8997.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Replace mfd_shared_platform_driver_register with mfd_clone_cell. The
former was called by an mfd client, and registered both a platform driver
and device. The latter is called by an mfd driver, and registers only a
platform device.
The downside of this is that mfd drivers need to be modified whenever
new clients are added that share a cell; the upside is that it fits
Linux's driver model better. It's also simpler.
This also converts cs5535-mfd/olpc-xo1 from the old API. cs5535-mfd
now creates the olpc-xo1-{acpi,pms} devices, while olpc-xo1 binds to
them via platform drivers.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The regulators on the AB8500 have a lot of custom
hardware control settings pertaining to 8 external
signals, settings which are board-specific and need
be provided from the platform at startup.
Initialization added for regulators Vana, VextSupply1,
VextSupply2, VextSupply3, Vaux1, Vaux2, Vaux3, VTVout,
Vintcore12, Vaudio, Vdmic, Vamic1, Vamic2, VrefDDR.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Reviewed-by: Rickard Andersson <rickard.andersson@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
On sh-mobile platforms the SDHI driver was using the tmio_mmc SD/SDIO
MFD cell driver. Now that the tmio_mmc driver has been split into a
core and a separate MFD glue, we can support SDHI natively without the
need to emulate an MFD controller. This also allows to support systems
with an on-SoC SDHI controller and a separate MFD with a TMIO core.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
Rename AB8500 GPADC header so as not to be redunantly named.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Allow const buffers to be passed in without type safety issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The TPS61050/TPS61052 are boost converters, LED drivers, LED flash
drivers and a simple GPIO pin chips.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Append the additional read/write operation on 88pm860x for accessing
test page in 88PM860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
led driver. So move the identification of device node from led
driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This revamps the interface so that AB8500 GPADCs are fetched by
name. Probed GPADCs are added to a list and this list is searched
for a matching GPADC. This makes it possible to have multiple
AB8500 GPADC instances instead of it being a singleton, and
rids the need to keep a GPADC pointer around in the core AB8500
MFD struct.
Currently the match is made to the device name which is by default
numbered from the device instance such as "ab8500-gpadc.0" but
by using the .init_name field of the device a more intiutive
naming for the GPADC blocks can be achieved if desired.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves the ab8500-gpadc.h header down into the ab8500/
subdir in include/linux/mfd and fixes some whitespace in the
header in the process.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
MAX8997/MAX8966 chip is a multi-function device with I2C bussses. The
chip includes PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery (charging) control.
This patch is an initial release of a MAX8997/8966 driver that supports
to enable the chip with its primary I2C bus that connects every device
mentioned above except for Fuel Gauge, which uses another I2C bus. The
fuel gauge is not supported by this mfd driver and is supported by a
seperated driver of MAX17042 Fuel Gauge (yes, the fuel gauge part is
compatible with MAX17042).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds support for ab8500 chip revision cut 3.0.
Also rephrased from Changes to Author in the header.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
