First set of i915 fixes for code in next.
* tag 'drm-intel-next-fixes-2016-12-22' of git://anongit.freedesktop.org/git/drm-intel:
drm/i915: skip the first 4k of stolen memory on everything >= gen8
drm/i915: Fallback to single PAGE_SIZE segments for DMA remapping
drm/i915: Fix use after free in logical_render_ring_init
drm/i915: disable PSR by default on HSW/BDW
drm/i915: Fix setting of boost freq tunable
drm/i915: tune down the fast link training vs boot fail
drm/i915: Reorder phys backing storage release
drm/i915/gen9: Fix PCODE polling during SAGV disabling
drm/i915/gen9: Fix PCODE polling during CDCLK change notification
drm/i915/dsi: Fix chv_exec_gpio disabling the GPIOs it is setting
drm/i915/dsi: Fix swapping of MIPI_SEQ_DEASSERT_RESET / MIPI_SEQ_ASSERT_RESET
drm/i915/dsi: Do not clear DPOUNIT_CLOCK_GATE_DISABLE from vlv_init_display_clock_gating
drm/i915: drop the struct_mutex when wedged or trying to reset
Here's the one lonely bugfix I talked about on irc.
* tag 'drm-misc-fixes-2016-12-22' of git://anongit.freedesktop.org/git/drm-misc:
drivers/gpu/drm/ast: Fix infinite loop if read fails
- fix display regression on DCE6/8
- Powergating fixes for GFX8
- amdgpu SI fixes (golden settings, proper rev id setup, etc.)
* 'drm-next-4.10' of git://people.freedesktop.org/~agd5f/linux: (21 commits)
drm/amdgpu: update tile table for oland/hainan
drm/amdgpu: update tile table for verde
drm/amdgpu: update rev id for verde
drm/amdgpu: update golden setting for verde
drm/amdgpu: update rev id for oland
drm/amdgpu: update golden setting for oland
drm/amdgpu: update rev id for hainan
drm/amdgpu: update golden setting for hainan
drm/amdgpu: update rev id for pitcairn
drm/amdgpu: update golden setting for pitcairn
drm/amdgpu: update golden setting/tiling table of tahiti
drm/amdgpu: fix cursor setting of dce6/dce8
drm/amdgpu: refine set clock gating for tonga/polaris
drm/amdgpu: initialize cg flags for tonga/polaris10/polaris11.
drm/amdgpu: add new gfx cg flags.
drm/amdgpu: fix pg can't be disabled by PG mask.
drm/amdgpu: always initialize gfx pg for gfx_v8.0.
drm/amdgpu: enable AMD_PG_SUPPORT_CP in Carrizo/Stoney.
drm/amdgpu: fix init save/restore list in gfx_v8.0
drm/amdgpu: fix enable_cp_power_gating in gfx_v8.0.
...
Pull block layer fixes from Jens Axboe:
"Just a set of small fixes that have either been queued up after the
original pull for this merge window, or just missed the original pull
request.
- a few bcache fixes/changes from Eric and Kent
- add WRITE_SAME to the command filter whitelist frm Mauricio
- kill an unused struct member from Ritesh
- partition IO alignment fix from Stefan
- nvme sysfs printf fix from Stephen"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: check partition alignment
nvme : Use correct scnprintf in cmb show
block: allow WRITE_SAME commands with the SG_IO ioctl
block: Remove unused member (busy) from struct blk_queue_tag
bcache: partition support: add 16 minors per bcacheN device
bcache: Make gc wakeup sane, remove set_task_state()
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng).
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=55TG
-----END PGP SIGNATURE-----
Merge tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"Here are new versions of two ACPICA changes that were deferred
previously due to a problem they had introduced, two cleanups on top
of them and the removal of a useless warning message from the ACPI
core.
Specifics:
- Move some Linux-specific functionality to upstream ACPICA and
update the in-kernel users of it accordingly (Lv Zheng)
- Drop a useless warning (triggered by the lack of an optional
object) from the ACPI namespace scanning code (Zhang Rui)"
* tag 'acpi-extra-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
ACPI: do not warn if _BQC does not exist
- Prevent the acpi-cpufreq driver from crashing on exit by fixing
a check against the __cpuhp_setup_state() return value and fix
the kerneldoc description of that function to make it clear that
it may return positive numbers on success too (Boris Ostrovsky).
- Drop an incorrect __init annotation of a function in the
s3c64xx cpufreq driver and fix a build warning generated (by
older compilers) because of it (Arnd Bergmann).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5bie
-----END PGP SIGNATURE-----
Merge tag 'pm-fixes-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"They fix one bug introduced recently, a build warning and a kerneldoc
function description.
Specifics:
- Prevent the acpi-cpufreq driver from crashing on exit by fixing a
check against the __cpuhp_setup_state() return value and fix the
kerneldoc description of that function to make it clear that it may
return positive numbers on success too (Boris Ostrovsky)
- Drop an incorrect __init annotation of a function in the s3c64xx
cpufreq driver and fix a build warning generated (by older
compilers) because of it (Arnd Bergmann)"
* tag 'pm-fixes-4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: s3c64xx: remove incorrect __init annotation
cpufreq: Remove CPU hotplug callbacks only if they were initialized
CPU/hotplug: Clarify description of __cpuhp_setup_state() return value
- Further fix thread wake-up for requests
- Use a bounce buffer to fix DMA issue for SSR register read
MMC host:
- sdhci: Fix a regression for runtime PM
- sdhci-cadence: Add a proper SoC specific DT compatible
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PDPZ
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"MMC core:
- further fix thread wake-up for requests
- use a bounce buffer to fix DMA issue for SSR register read
MMC host:
- sdhci: Fix a regression for runtime PM
- sdhci-cadence: Add a proper SoC specific DT compatible"
* tag 'mmc-v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sd: Meet alignment requirements for raw_ssr DMA
mmc: core: Further fix thread wake-up
mmc: sdhci: Fix to handle MMC_POWER_UNDEFINED
mmc: sdhci-cadence: add Socionext UniPhier specific compatible string
Pull SElinux fix from James Morris:
"From Paul:
'A small SELinux patch to fix some clang/llvm compiler warnings and
ensure the tools under scripts work well in the face of kernel
changes'"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: use the kernel headers when building scripts/selinux
Pull x86 cache allocation interface from Thomas Gleixner:
"This provides support for Intel's Cache Allocation Technology, a cache
partitioning mechanism.
The interface is odd, but the hardware interface of that CAT stuff is
odd as well.
We tried hard to come up with an abstraction, but that only allows
rather simple partitioning, but no way of sharing and dealing with the
per package nature of this mechanism.
In the end we decided to expose the allocation bitmaps directly so all
combinations of the hardware can be utilized.
There are two ways of associating a cache partition:
- Task
A task can be added to a resource group. It uses the cache
partition associated to the group.
- CPU
All tasks which are not member of a resource group use the group to
which the CPU they are running on is associated with.
That allows for simple CPU based partitioning schemes.
The main expected user sare:
- Virtualization so a VM can only trash only the associated part of
the cash w/o disturbing others
- Real-Time systems to seperate RT and general workloads.
- Latency sensitive enterprise workloads
- In theory this also can be used to protect against cache side
channel attacks"
[ Intel RDT is "Resource Director Technology". The interface really is
rather odd and very specific, which delayed this pull request while I
was thinking about it. The pull request itself came in early during
the merge window, I just delayed it until things had calmed down and I
had more time.
But people tell me they'll use this, and the good news is that it is
_so_ specific that it's rather independent of anything else, and no
user is going to depend on the interface since it's pretty rare. So if
push comes to shove, we can just remove the interface and nothing will
break ]
* 'x86-cache-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
x86/intel_rdt: Implement show_options() for resctrlfs
x86/intel_rdt: Call intel_rdt_sched_in() with preemption disabled
x86/intel_rdt: Update task closid immediately on CPU in rmdir and unmount
x86/intel_rdt: Fix setting of closid when adding CPUs to a group
x86/intel_rdt: Update percpu closid immeditately on CPUs affected by changee
x86/intel_rdt: Reset per cpu closids on unmount
x86/intel_rdt: Select KERNFS when enabling INTEL_RDT_A
x86/intel_rdt: Prevent deadlock against hotplug lock
x86/intel_rdt: Protect info directory from removal
x86/intel_rdt: Add info files to Documentation
x86/intel_rdt: Export the minimum number of set mask bits in sysfs
x86/intel_rdt: Propagate error in rdt_mount() properly
x86/intel_rdt: Add a missing #include
MAINTAINERS: Add maintainer for Intel RDT resource allocation
x86/intel_rdt: Add scheduler hook
x86/intel_rdt: Add schemata file
x86/intel_rdt: Add tasks files
x86/intel_rdt: Add cpus file
x86/intel_rdt: Add mkdir to resctrl file system
x86/intel_rdt: Add "info" files to resctrl file system
...
My previous email address is no longer valid.
From now on, jacek.anaszewski@gmail.com should be used instead.
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Jiri reported the overlap scheduling exceeding its max stack.
Looking at the constraint that triggered this, it turns out the
overlap marker isn't needed.
The comment with EVENT_CONSTRAINT_OVERLAP states: "This is the case if
the counter mask of such an event is not a subset of any other counter
mask of a constraint with an equal or higher weight".
Esp. that latter part is of interest here I think, our overlapping mask
is 0x0e, that has 3 bits set and is the highest weight mask in on the
PMU, therefore it will be placed last. Can we still create a scenario
where we would need to rewind that?
The scenario for AMD Fam15h is we're having masks like:
0x3F -- 111111
0x38 -- 111000
0x07 -- 000111
0x09 -- 001001
And we mark 0x09 as overlapping, because it is not a direct subset of
0x38 or 0x07 and has less weight than either of those. This means we'll
first try and place the 0x09 event, then try and place 0x38/0x07 events.
Now imagine we have:
3 * 0x07 + 0x09
and the initial pick for the 0x09 event is counter 0, then we'll fail to
place all 0x07 events. So we'll pop back, try counter 4 for the 0x09
event, and then re-try all 0x07 events, which will now work.
The masks on the PMU in question are:
0x01 - 0001
0x03 - 0011
0x0e - 1110
0x0c - 1100
But since all the masks that have overlap (0xe -> {0xc,0x3}) and (0x3 ->
0x1) are of heavier weight, it should all work out.
Reported-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Liang Kan <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Robert Richter <rric@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20161109155153.GQ3142@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch solves a race condition between PEBS and the PMU handler.
In case multiple PEBS events are sampled at the same time,
it is possible to have GLOBAL_STATUS bit 62 set indicating
PEBS buffer overflow and also seeing at most 3 PEBS counters
having their bits set in the status register. This is a sign
that there was at least one PEBS record pending at the time
of the PMU interrupt. PEBS counters must only be processed
via the drain_pebs() calls, and not via the regular sample
processing loop coming after that the function, otherwise
phony regular samples may be generated in the sampling buffer
not marked with the EXACT tag.
Another possibility is to have one PEBS event and at least
one non-PEBS event whic hoverflows while PEBS has armed. In this
case, bit 62 of GLOBAL_STATUS will not be set, yet the overflow
status bit for the PEBS counter will be on Skylake.
To avoid this problem, we systematically ignore the PEBS-enabled
counters from the GLOBAL_STATUS mask and we always process PEBS
events via drain_pebs().
The problem manifested itself by having non-exact samples when
sampling only PEBS events, i.e., the PERF_SAMPLE_RECORD would
not have the EXACT flag set.
Note that this problem is only present on Skylake processor.
This fix is harmless on older processors.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1482395366-8992-1-git-send-email-eranian@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A bugfix commit:
45dbea5f55 ("x86/paravirt: Fix native_patch()")
... introduced a harmless warning:
arch/x86/kernel/paravirt_patch_32.c: In function 'native_patch':
arch/x86/kernel/paravirt_patch_32.c:71:1: error: label 'patch_default' defined but not used [-Werror=unused-label]
Fix it by annotating the label as __maybe_unused.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Piotr Gregor <piotrgregor@rsyncme.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 45dbea5f55 ("x86/paravirt: Fix native_patch()")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
pkt->qp was already dereferenced earlier in the function.
Fixes Smatch complaint:
drivers/infiniband/sw/rxe/rxe_net.c:458 send()
warn: variable dereferenced before check 'pkt->qp' (see line 441)
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
If the completer is in the middle of a large read operation, one
lost packet can cause havoc. Going to COMPST_ERROR_RETRY will
cause the requester to resend the request. After that, any packet
from the first attempt still in the receive queue will be
interpreted as an error, restarting the error/retry sequence.
The transfer will quickly exhaust its retries.
This behavior is very noticeable when doing 512KB reads on a
QEMU system configured with 1500B MTU.
Also, a resent request here will prompt the responder on the
other side to immediately start resending, but the resent
packets will get stuck in the already-loaded receive queue and
will never be processed.
Rather than erroring out every time an unexpected future packet
arrives, just drop it. Eventually the retry timer will send a
duplicate request; the completer will be able to make progress since
the queue will start relatively empty.
Signed-off-by: Andrew Boyer <andrew.boyer@dell.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We clear the vendor error field in the work completion so that if
a work completion is erroneous the field won't confuse the caller.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Reviewed-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Enable posting to SQ only in RTS, ERR and SQD QP state.
Enable posting to RQ in ERR QP state.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Reviewed-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the current implementation a read verb with IB_SEND_INLINE may be
illegally configured.
In this fix we ignore the inline bit in the case of a read verb.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Reviewed-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current code didn't modify the QP state to error because it queried the
QP state as a bitmap while it isn't. So the code never got executed.
This patch fixes this and queries for each QP state respectively and not
at once via a bitmask.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Reviewed-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Configure ibcq->cqe when a CQ is created.
Signed-off-by: Ram Amrani <Ram.Amrani@cavium.com>
Reviewed-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
RQ WQE size other than 128B is not supported. Correct
RQ size calculation to use 128B only.
Since this breaks ABI, add additional code to
provide compatibility with v4 user provider, libi40iw.
Signed-off-by: Chien Tin Tung <chien.tin.tung@intel.com>
Signed-off-by: Henry Orosco <henry.orosco@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Code that dereferences the struct net_device ip_ptr member must be
protected with an in_dev_get() / in_dev_put() pair. Hence insert
calls to these functions.
Fixes: commit 7b85627b9f ("IB/cma: IBoE (RoCE) IP-based GID addressing")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Roland Dreier <roland@purestorage.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All small fixes this time, especially important are the regression
fixes for rtlwifi and ath9k.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYW+jGAAoJEG4XJFUm622bFIUH/isc9kpL63eJOwKr6P0Uow92
XF+OcrnhRxlVqAsMx0yvrNsVAIZkLfAjJhLZv91h5Vpv0UCnLP4LpH1IqwiHih1u
oxZVbcV7qAOZopgvWDU8R2Nh6Z4FPWYmDttvg86rQKLh82DuNCvl+btl/cCFaVDS
5T1xpY+BP2CbIUyTJ3Sg1t4yZI06dZODaLuiFzxM1MjEhQ0p785VJBASekLzo6YE
6YMzDIP6iir/WKod9HXtJJIgv+gBiZMCTmw7QH+G2o/i3WIjclqsSSwCepDCpmlI
AuicYeeObWPOQFpCpD4KgrshdLM/zytLuRvaU8lVofr81I98Hs8rHBbYJTwZsGE=
=kA4D
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-12-22' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.10
All small fixes this time, especially important are the regression
fixes for rtlwifi and ath9k.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e2d118a1cb ("net: inet: Support UID-based routing in IP
protocols.") made ip_do_redirect call sock_net(sk) to determine
the network namespace of the passed-in socket. This crashes if sk
is NULL.
Fix this by getting the network namespace from the skb instead.
Fixes: e2d118a1cb ("net: inet: Support UID-based routing in IP protocols.")
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* pm-cpufreq:
cpufreq: s3c64xx: remove incorrect __init annotation
cpufreq: Remove CPU hotplug callbacks only if they were initialized
CPU/hotplug: Clarify description of __cpuhp_setup_state() return value
* acpica:
ACPI / osl: Remove deprecated acpi_get_table_with_size()/early_acpi_os_unmap_memory()
ACPI / osl: Remove acpi_get_table_with_size()/early_acpi_os_unmap_memory() users
ACPICA: Tables: Allow FADT to be customized with virtual address
ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel
* acpi-scan:
ACPI: do not warn if _BQC does not exist
Removing all trailing whitespaces in befs.
I was skeptic about tainting the history with this, but whitespace changes
can be ignored by using 'git blame -w' and 'git log -w'.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
No idea why some comments have signatures. These predate git. Removing them
since they add noise and no information.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Fixing checkpatch.pl issues in befs header files:
WARNING: Missing a blank line after declarations
+ befs_inode_addr iaddr;
+ iaddr.allocation_group = blockno >> BEFS_SB(sb)->ag_shift;
WARNING: space prohibited between function name and open parenthesis '('
+ return BEFS_SB(sb)->block_size / sizeof (befs_disk_inode_addr);
ERROR: "foo * bar" should be "foo *bar"
+ const char *key, befs_off_t * value);
ERROR: Macros with complex values should be enclosed in parentheses
+#define PACKED __attribute__ ((__packed__))
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Fix the following type of checkpatch.pl issues:
WARNING: line over 80 characters
+static struct dentry *befs_lookup(struct inode *, struct dentry *, unsigned int);
ERROR: code indent should use tabs where possible
+ if (!bi)$
WARNING: please, no spaces at the start of a line
+ if (!bi)$
WARNING: labels should not be indented
+ unacquire_bh:
WARNING: space prohibited between function name and open parenthesis '('
+ sizeof (struct befs_inode_info),
WARNING: braces {} are not necessary for single statement blocks
+ if (!*out) {
+ return -ENOMEM;
+ }
WARNING: Block comments use a trailing */ on a separate line
+ * in special cases */
WARNING: Missing a blank line after declarations
+ int token;
+ if (!*p)
ERROR: do not use assignment in if condition
+ if (!(bh = sb_bread(sb, sb_block))) {
ERROR: space prohibited after that open parenthesis '('
+ if( befs_sb->num_blocks > ~((sector_t)0) ) {
ERROR: space prohibited before that close parenthesis ')'
+ if( befs_sb->num_blocks > ~((sector_t)0) ) {
ERROR: space required before the open parenthesis '('
+ if( befs_sb->num_blocks > ~((sector_t)0) ) {
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Fixing the two following checkpatch.pl issues:
ERROR: trailing whitespace
+ * Based on portions of file.c and inode.c $
WARNING: labels should not be indented
+ error:
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Fixing the following checkpatch.pl errors and warning:
ERROR: trailing whitespace
+ * $
WARNING: Block comments use * on subsequent lines
+/*
+ Validates the correctness of the befs inode
ERROR: "foo * bar" should be "foo *bar"
+befs_check_inode(struct super_block *sb, befs_inode * raw_inode,
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
This address hasn't been accurate for several years now.
Simply remove it.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Trivial fix: Addresses should be printed using the %p format specifier
rather than using %x.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Madalin reported crashes happening in tcp_tasklet_func() on powerpc64
Before TSQ_QUEUED bit is cleared, we must ensure the changes done
by list_del(&tp->tsq_node); are committed to memory, otherwise
corruption might happen, as an other cpu could catch TSQ_QUEUED
clearance too soon.
We can notice that old kernels were immune to this bug, because
TSQ_QUEUED was cleared after a bh_lock_sock(sk)/bh_unlock_sock(sk)
section, but they could have missed a kick to write additional bytes,
when NIC interrupts for a given flow are spread to multiple cpus.
Affected TCP flows would need an incoming ACK or RTO timer to add more
packets to the pipe. So overall situation should be better now.
Fixes: b223feb9de ("tcp: tsq: add shortcut in tcp_tasklet_func()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Madalin Bucur <madalin.bucur@nxp.com>
Tested-by: Madalin Bucur <madalin.bucur@nxp.com>
Tested-by: Xing Lei <xing.lei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8924feff66 ("splice: lift pipe_lock out of splice_to_pipe()")
caused a regression when there were no more readers left on a pipe that
was being spliced into: rather than the expected SIGPIPE and -EPIPE
return value, the writer would end up waiting forever for space to free
up (which obviously was not going to happen with no readers around).
Fixes: 8924feff66 ("splice: lift pipe_lock out of splice_to_pipe()")
Reported-and-tested-by: Andreas Schwab <schwab@linux-m68k.org>
Debugged-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: stable@kernel.org # v4.9
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull parisc updates from Helge Deller:
- add Kernel address space layout randomization support
- re-enable interrupts earlier now that we have a working IRQ stack
- optimize the timer interrupt function to better cope with missed
timer irqs
- fix error return code in parisc perf code (by Dan Carpenter)
- fix PAT debug code
* 'parisc-4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Optimize timer interrupt function
parisc: perf: return -EFAULT on error
parisc: Enhance CPU detection code on PAT machines
parisc: Re-enable interrupts early
parisc: Enable KASLR
Highlights include:
- Further attribute cache improvements to make revalidation more fine grained
- NFSv4 locking improvements
Bugfixes:
- nfs4_fl_prepare_ds must be careful about reporting success in files layout
- pNFS/flexfiles: Instead of marking a device inactive, remove it from the cache
-----BEGIN PGP SIGNATURE-----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=8gLp
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-4.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull more NFS client updates from Trond Myklebust:
"Highlights include:
- further attribute cache improvements to make revalidation more fine
grained
- NFSv4 locking improvements
Bugfixes:
- nfs4_fl_prepare_ds must be careful about reporting success in files
layout
- pNFS/flexfiles: Instead of marking a device inactive, remove it
from the cache"
* tag 'nfs-for-4.10-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Retry the DELEGRETURN if the embedded GETATTR is rejected with EACCES
NFS: Retry the CLOSE if the embedded GETATTR is rejected with EACCES
NFSv4: Place the GETATTR operation before the CLOSE
NFSv4: Also ask for attributes when downgrading to a READ-only state
NFS: Don't abuse NFS_INO_REVAL_FORCED in nfs_post_op_update_inode_locked()
pNFS: Return RW layouts on OPEN_DOWNGRADE
NFSv4: Add encode/decode of the layoutreturn op in OPEN_DOWNGRADE
NFS: Don't disconnect open-owner on NFS4ERR_BAD_SEQID
NFSv4: ensure __nfs4_find_lock_state returns consistent result.
NFSv4.1: nfs4_fl_prepare_ds must be careful about reporting success.
pNFS/flexfiles: delete deviceid, don't mark inactive
NFS: Clean up nfs_attribute_timeout()
NFS: Remove unused function nfs_revalidate_inode_rcu()
NFS: Fix and clean up the access cache validity checking
NFS: Only look at the change attribute cache state in nfs_weak_revalidate()
NFS: Clean up cache validity checking
NFS: Don't revalidate the file on close if we hold a delegation
NFSv4: Don't discard the attributes returned by asynchronous DELEGRETURN
NFSv4: Update the attribute cache info in update_changeattr
Since commit 71ce391dfb ("net: mvpp2: enable proper per-CPU TX
buffers unmapping"), we are not correctly DMA unmapping TX buffers for
fragments.
Indeed, the mvpp2_txq_inc_put() function only stores in the
txq_cpu->tx_buffs[] array the physical address of the buffer to be
DMA-unmapped when skb != NULL. In addition, when DMA-unmapping, we use
skb_headlen(skb) to get the size to be unmapped. Both of this works fine
for TX descriptors that are associated directly to a SKB, but not the
ones that are used for fragments, with a NULL pointer as skb:
- We have a NULL physical address when calling DMA unmap
- skb_headlen(skb) crashes because skb is NULL
This causes random crashes when fragments are used.
To solve this problem, we need to:
- Store the physical address of the buffer to be unmapped
unconditionally, regardless of whether it is tied to a SKB or not.
- Store the length of the buffer to be unmapped, which requires a new
field.
Instead of adding a third array to store the length of the buffer to be
unmapped, and as suggested by David Miller, this commit refactors the
tx_buffs[] and tx_skb[] arrays of 'struct mvpp2_txq_pcpu' into a
separate structure 'mvpp2_txq_pcpu_buf', to which a 'size' field is
added. Therefore, instead of having three arrays to allocate/free, we
have a single one, which also improve data locality, reducing the
impact on the CPU cache.
Fixes: 71ce391dfb ("net: mvpp2: enable proper per-CPU TX buffers unmapping")
Reported-by: Raphael G <raphael.glon@corp.ovh.com>
Cc: Raphael G <raphael.glon@corp.ovh.com>
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the dwmac-rk tries to set up the GRF-specific speed and link
options before enabling clocks, phys etc and on previous socs this works
because the GRF is supplied on the whole by one clock.
On the rk3399 however the GRF (General Register Files) clock-supply
has been split into multiple clocks and while there is no specific
grf-gmac clock like for other sub-blocks, it seems the mac-specific
portions are actually supplied by the general mac clock.
This results in hangs on rk3399 boards if the driver is build as module.
When built in te problem of course doesn't surface, as the clocks
are of course still on at the stage before clock_disable_unused.
To solve this, simply move the clock enablement to the first position
in the powerup callback. This is also a good idea in general to
enable clocks before everything else.
Tested on rk3288, rk3368 and rk3399 the dwmac still works on all of them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently allocates 128 bytes of skb headroom.
This was found to be insufficient with some configurations
like Geneve tunnels, which resulted in skb head reallocations.
Increase the headroom to 256 bytes to fix this.
Signed-off-by: Kalesh A P <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scsi target cleanups from Bart Van Assche:
"The changes here are:
- a few small bug fixes for the iSCSI and user space target drivers.
- minimize the target build time by about 30% by rearranging #include
directives
- fix the second argument passed to percpu_ida_alloc()
- reduce the number of false positive warnings reported by sparse
These patches pass Wu Fengguang's build bot tests and also the
linux-next tests"
* 'scsi-target-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bvanassche/linux:
iscsi-target: Return error if unable to add network portal
target: Fix spelling mistake and unwrap multi-line text
target/iscsi: Fix double free in lio_target_tiqn_addtpg()
target/user: Fix use-after-free of tcmu_cmds if they are expired
target: Minimize #include directives
target/user: Add an #include directive
cxgbit: Add an #include directive
ibmvscsi_tgt: Add two #include directives
sbp-target: Add an #include directive
qla2xxx: Add an #include directive
configfs: Minimize #include directives
usb: gadget: Fix second argument of percpu_ida_alloc()
sbp-target: Fix second argument of percpu_ida_alloc()
target/user: Fix a data type in tcmu_queue_cmd()
target: Use NULL instead of 0 to represent a pointer
