RBC is to control whether some ANATOP sub modules
can enter lpm mode when SOC is into STOP mode, if
RBC is enabled and PMIC_VSTBY_REQ is set, ANATOP
will have below behaviors:
1. Digital LDOs(CORE, SOC and PU) are bypassed;
2. Analog LDOs(1P1, 2P5, 3P0) are disabled;
As the 2P5 is necessary for DRAM IO pre-drive in
STOP mode, so we need to enable weak 2P5 in STOP
mode when 2P5 LDO is disabled.
For RBC settings, there are some rules as below
due to hardware design:
1. All interrupts must be masked during operating
RBC registers;
2. At least 2 CKIL(32K) cycles is needed after the
RBC setting is changed.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Anatop module have sereval configurations for user
to reduce the power consumption in suspend, provide
suspend/resume interface for further use and enable
fet_odrive to reduce CORE LDO leakage during suspend.
As we have a common anatop file, remove all the operations
of anatop module in other files, use anatop interfaces to
do that.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Clean up a couple of unneeded function declarations
* Remove imx specific cpufreq driver as generic cpufreq-cpu0 works well
as the replacement
* Remove platform ahci support
* Clean up unused ARCH/MACH Kconfig symbols
* Remove a couple of unused files
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRZBpzAAoJEFBXWFqHsHzOfyAH/RdvhORI0rNhBAOrSxleWlMy
AMP9x6G5tXNK/fgtxopvCiS4VXw5MB01uqJWMVM9+hx6676oCXWc/L3I6iT5l87B
qPY/e9LyGJa5aOYczPuUT2sG+Ga8989GhOksA+L6kWHZ2df0BIB9rBRZnoPezEAx
u2ATdioyzfj2rAnDNFOxsw6oai265mowt/f8J/7EQfxgkAMcKov7/BpVac0po55R
tv+Hr3T7OBg3p/h5PYi5iAehVCToCKOD31QpnlhS+dmKS52w7tEO6T75INt7HzC8
CJT0zi5jJ3/tDJsdYJ1SS4MHK4U43y0oV7cw7sO7TzNreyOB6bzTWDqhdJY2oMM=
=N7xl
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup-3.10' into imx/soc
The imx cleanup for 3.10:
* Clean up a couple of unneeded function declarations
* Remove imx specific cpufreq driver as generic cpufreq-cpu0 works well
as the replacement
* Remove platform ahci support
* Clean up unused ARCH/MACH Kconfig symbols
* Remove a couple of unused files
Commit a1f1c7e (arm/imx6q: add suspend/resume support) added
declaration for a non-existing function pl310_get_save_ptr() by
mistake. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
There is a sync issue with hotplug operation. It's possible that when
imx_cpu_kill gets running on primary core, the imx_cpu_die execution
on the core which is to be killed hasn't been finished yet. The problem
will very likely be hit when running suspend without no_console_suspend
setting on kernel cmdline.
It uses cpu jumping argument register to sync imx_cpu_die and
imx_cpu_kill. The register will be set in imx_cpu_die and imx_cpu_kill
will wait for the register being cleared to actually kill the cpu.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
- It's based on imx-cleanup-3.9 to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCRzjAAoJEFBXWFqHsHzOOTYH/2YiAhCXDoovJ++leTTBKoFO
kRx2gvV0oxQYAjvRX4IiiwcuWjbCQI8ugiKxeH9Vn+jwHD8jKqzTINEUVQfKUud6
s8AI1/EqKwKnEFYFs/Fg6WxZHuHpoL/clpRB/5wZw1KoChmte2OnVU7d9vOt67iN
l0P4nPR18iwU5LFoDCnqMX50Dp9C56KEF2JhzBCQKW9TtRclwpcBNy6AsHb/TNOe
/nHN+Ku6/3xQEz2MPQ9QdmgFxnp9Pr8R6leJNg1Vg6UGRYrKxy0zVo+oFEXAZuUw
v6gnhdlvO6Ki/IKHcWkw7Q7pUDTuB6SttirQE9mBlPdc0V3kTU82SVtX9WAQhSs=
=rVol
-----END PGP SIGNATURE-----
Merge tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
imx6q cpuidle support for 3.9
- It's based on imx-cleanup-3.9 to avoid conflicts.
* tag 'imx6q-cpudile-3.9' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: imx6q: support WAIT mode using cpuidle
ARM: imx: move imx6q_cpuidle_driver into a separate file
ARM: imx: mask gpc interrupts initially
ARM: imx: return zero in case next event gets a large increment
ARM: imx: Remove mx508 support
ARM: imx: Remove mach-mx51_3ds board
ARM: imx: use debug_ll_io_init() for imx6q
ARM: imx: remove unused imx6q_clock_map_io()
ARM: mach-imx: Kconfig: Do not select Babbage for MACH_IMX51_DT
Signed-off-by: Olof Johansson <olof@lixom.net>
Still, two delete/change conflicts caused by imx/cleanup:
arch/arm/mach-imx/mach-mx50_rdp.c
arch/arm/mach-imx/mach-mx51_3ds.c
Add WAIT mode (ARM core clock gating) support to imx6q cpuidle driver.
As WAIT mode is broken on imx6q TO 1.0 and 1.1, it only enables the
support for revision 1.2 with chicken bit set.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Only mx508 based board is mach-mx50_rdp and it has been marked as BROKEN
for several releases.
mx508 currently lacks clock support.
In case someone needs to add mx508 support back, then the recommended approach
is to use device tree.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Use debug_ll_io_init() to map low level debug port for imx6q, so that
arch/arm/mach-imx/lluart.c can be removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q_clock_map_io() becomes an empty function since imx6q clock driver
is moved to common clock framework. It's used nowhere now. Remove it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It's buggy to disable the cpu that is being hot-unplugged in .cpu_die
hook which runs on the cpu itself. Instead, it should be done in
.cpu_kill which runs on the thread (another cpu) that asks for shutting
down the cpu. Move imx_enable_cpu(cpu, false) call into .cpu_kill
hook, and leave the cpu to be hot-unplugged in WFI within .cpu_die,
so that we can get a more stable cpu hot-plug operation.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Now that the GIC initialization sets up the handle_arch_irq pointer, we
can remove it for all machines and make it static.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Anton Vorontsov <avorontsov@mvista.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
This adds a i.MX25 dt machine descriptor and changes the clock
support to optionally initialize from dt.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
mxc_device_init() is a core_initcall function used to register devices
for mxc_aips_bus and mxc_ahb_bus, which are needed by gpio and dma
device registration.
Instead of being a core_initcall function, we have it called in soc
specific initialization function before gpio and dma devices get
registered, so that it will not be called for other platforms when
we enable multi-platform support for imx.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.
It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
