Change return code in slave_alloc to avoid irritating error message from
scsi_alloc_sdev() when scsi stack tries target scan.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Don't check link down payload in case of firmware update.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixed various problems in opening sequence of adapters which was previously
changed with NPIV support:
o corrected handling when exchange port data function is not supported,
otherwise adapters on z900 cannot be opened anymore
o corrected setup of timer for exchange port data if called from error
recovery
o corrected check of return code of exchange config data
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move initialization of locks and lists to adapter allocation function.
Otherwise we might end up with some uninitialized locks, like e.g. the
erp locks which only will be inititialized if an error recovery thread
for an adapter will be started.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn.
scsi_bios_ptable return value is not being checked in aac_biosparm.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some SCSI devices apparently get very confused if we try to use the
echo buffer on a non-DT negotiated bus (this mirrors the problems of
using PPR on non-LVD for some devices). The fix is to be far more
conservative about when we use an echo buffer. With this patch, we'll
now see what parameters are negotiated by the read only test, and only
look for an echo buffer if DT is negotiated.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To transport scsi reset command to device aic7xxx reset handler looks
at the driver's pending_list and searches any proper command. However
the search condition has been inverted: ahc_match_scb() returns TRUE
if a matched command is found. As a result the reset on required
devices did not turn out well, a correctly working neighbour device
may be surprised by the reset. aic7xxx reset handler reports about the
success, but really the original situation is not corrected yet.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Naturally, there's a corresponding problem in the aic79xx driver, so
I've also added the same fix for that.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The Coverity checker spotted this obvious use-after-release bug caused
by a wrong order of the cleanups.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This code fixes a tiny problem with the recent fbcon rotation changes:
fb_prepare_logo doesn't check the return value of fb_find_logo and that
causes a crash for my while booting.
Obvious & working & tested fix is here.
Signed-off-by: Jasper Spaans <jasper@vs19.net>
Acked-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A fix for a locking bug which is triggered when a client tries to lock with
flag DMA_QUIESCENT (typically the X server), but gets interrupted by a signal.
The locking IOCTL should then return an error, but if DMA_QUIESCENT succeeds
it returns 0, and the client falsely thinks it has the lock. In addition
The client waits for DMA_QUISCENT and possibly DMA_READY without having the lock.
From: Thomas Hellstrom
Signed-off-by: Dave Airlie <airlied@linux.ie>
remove redundant include
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On Wed, Nov 16, 2005 at 06:34:24PM -0800, Pete Zaitcev wrote:
>On Wed, 16 Nov 2005 23:52:32 +0100, David Hrdeman <david@2gen.com> wrote:
>> usb-storage: waiting for device to settle before scanning
>> Vendor: I0MEGA Model: UMni1GB*IOM2K4 Rev: 1.01
>> Type: Direct-Access ANSI SCSI revision: 02
>> SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
>> sda: Write Protect is off
>> sda: Mode Sense: 00 00 00 00
>> sda: assuming drive cache: write through
>> ioctl_internal_command: <8 0 0 0> return code = 8000002
>> : Current: sense key=0x0
>> ASC=0x0 ASCQ=0x0
>> SCSI device sda: 2048000 512-byte hdwr sectors (1049 MB)
>
>I think it's harmless. I saw things like that, and initially I plugged
>them with workarounds like this:
Thanks for the pointer, and yes, it is harmless, but it floods the
console with the messages which hides other (potentially important)
messages...following your example I've made a patch which fixes the
problem.
Signed-off-by: David Hrdeman <david@2gen.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This should fix a suspend/resume issues that appear with OHCI on some
PPC hardware. The PCI layer should doesn't have the hooks needed for
such ASIC-specific hooks (in this case, software clock gating), so
this moves the code to do that into hcd-pci.c ... where it can be
done after the relevant PCI PM state transition (to/from D3).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Moving the PCI-specific parts of the EHCI driver into their own file
created a few issues ... notably on resume paths which (like swsusp)
require re-initializing the controller. This patch:
- Splits the EHCI startup code into run-once HCD setup code and
separate "init the hardware" reinit code. (That reinit code is
a superset of the "early usb handoff" code.)
- Then it makes the PCI init code run both, and the resume code only
run the reinit code.
- It also removes needless pci wrappers around EHCI start/stop methods.
- Removes a byteswap issue that would be seen on big-endian hardware.
The HCD glue still doesn't actually provide a good way to do all this
run-one init stuff in one place though.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This cleans up the recent updates to EHCI PCI support:
- Gets rid of checks for "is this a PCI device", they're no
longer needed since this is now all PCI-only code.
- Reduce log spamming: MWI is only interesting in the atypical
case that it can actually be used.
- Whitespace cleanup, as appropriate for a new file with no
other pending patches.
So other than that minor logging change, no functional updates.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes some bugs in EHCI suspend/resume that joined us over the past
few releases (as usbcore, PCI, pmcore, and other components evolved):
- Removes suspend and resume recursion from the EHCI driver, getting
rid of the USB_SUSPEND special casing.
- Updates the wakeup mechanism to work again; there's a newish usbcore
call it needs to use.
- Provide simpler tests for "do we need to restart from scratch", to
address another case where PCI Vaux was lost. (In this case it was
restoring a swsusp snapshot, but there could be others.)
Un-exports a symbol that was temporarily exported.
A notable change from previous version is that this doesn't move
the spinlock init, so there's still a resume/reinit path bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds two new devices to the ftdi_sio driver's device ID
table. The device IDs were supplied by Stefan Nies of KOBIL Systems for
two of their devices using the FTDI chip.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch solves the following problem I've already discovered on the
latest 2.6.15-rc1-git1 kernel:
Nov 13 07:37:28 wrobel kernel: Bad page state at free_hot_cold_page (in process 'motion', page c164e020)
Nov 13 07:37:28 wrobel kernel: flags:0x40000400 mapping:00000000 mapcount:0 count:0
Nov 13 07:37:28 wrobel kernel: Backtrace:
Nov 13 07:37:28 wrobel kernel: [<c0146d86>] bad_page+0x85/0xbe
Nov 13 07:37:28 wrobel kernel: [<c0147629>] free_hot_cold_page+0x54/0x129
Nov 13 07:37:28 wrobel kernel: [<c01598c6>] __vunmap+0xa9/0xfe
Nov 13 07:37:28 wrobel kernel: [<c0154114>] vmalloc_to_page+0x34/0x55
Nov 13 07:37:28 wrobel kernel: [<c0159942>] vfree+0x27/0x35
Nov 13 07:37:28 wrobel kernel: [<f8a20292>] sn9c102_release_buffers+0x30/0x3f [sn9c102]
Nov 13 07:37:28 wrobel kernel: [<f8a231c2>] sn9c102_release+0x37/0xeb [sn9c102]
Nov 13 07:37:28 wrobel kernel: [<c0163e74>] __fput+0xa9/0x1aa
Nov 13 07:37:28 wrobel kernel: [<c01624f7>] filp_close+0x49/0x6d
Nov 13 07:37:30 wrobel kernel: [<c016258f>] sys_close+0x74/0x95
Nov 13 07:37:30 wrobel kernel: [<c0102ef9>] syscall_call+0x7/0xb
Nov 13 07:37:31 wrobel kernel: Trying to fix it up, but a reboot is needed
Signed-off-by: Damian Wrobel <dwrobel@ertel.com.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Per the PCI Express spec, the power-fault-detected bit in the
slot status register can be set anytime hardware detects a power
fault, regardless of whether the slot has a device populated in
it or not. This bit is sticky and must be explicitly cleared.
This patch is needed to allow hot-add after such a power fault
has been detected.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trivial patch to report both hdaps axises to the joystick device, not
just the X axis.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a bug where setting the low fan speed limits will not work if no
data was ever read through the sysfs interface and the fan clock
dividers have not been explicitely set yet either. The reason is that
data->fan_div[nr] may currently be used before it is initialized from
the chip register values. The fix is to explicitely initialize
data->fan_div[nr] before using it.
Bug reported, and fix tested, by Nicolas Mailhot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the lm78 VID reading, which I accidentally broke while making
this driver use the common vid_from_reg function rather than
reimplementing its own in 2.6.14-rc1.
I'm not proud of it, trust me.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add SENSORS_LIMIT in store VCore limit functions. This fixes a potential
u8 overflow on out-of-range user input.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch (as603) makes a few small fixes to the driver core:
Change spin_lock_irq for a klist lock to spin_lock;
Fix reference count leaks;
Minor spelling and formatting changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by Patrick Mochel <mochel@digitalimplant.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fix causes problems on the very first floppy access - we haven't yet
talked to the FDC so we don't know which state the write-protect tab is in.
Revert for now.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We memset the structure across opens except for the flags. The correct
fix is more intrusive but this should fix a problem with bad iounmaps
seen on AGP radeons acting like PCI ones.
Signed-off-by: Dave Airlie <airlied@linux.ie>
The DRM only uses drm_alloc_pages for non-SG PCI cards using DRM.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
PCI->PCI bridge, then bus->self is allowed to be NULL. Certainly that's
the case on my Pegasos, and it makes the MGA DRM driver oops...
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The spinlock region_lock is held while calling mark_region which can sleep.
Drop the spinlock before calling that function.
A region's state and inclusion in the clean list are altered by rh_inc and
rh_dec. The state variable is set to RH_CLEAN in rh_dec, but only if
'pending' is zero. It is set to RH_DIRTY in rh_inc, but not if it is already
so. The changes to 'pending', the state, and the region's inclusion in the
clean list need to be atomicly.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bio_list_merge() should do nothing if the second list is empty - not oops.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_end_io() can be called without interrupts blocked.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The linux bitset operators (test_bit, set_bit etc) work on arrays of "unsigned
long". dm-log uses such bitsets but treats them as arrays of uint32_t, only
allocating and zeroing a multiple of 4 bytes (as 'clean_bits' is a uint32_t).
The patch below fixes this problem.
The problem is specific to 64-bit big endian machines such as s390x or ppc-64
and can prevent pvmove terminating.
In the simplest case, if "region_count" were (say) 30, then
bitset_size (below) would be 4 and bitset_uint32_count would be 1.
Thus the memory for this butset, after allocation and zeroing would
be
0 0 0 0 X X X X
On a bigendian 64bit machine, bit 0 for this bitset is in the 8th
byte! (and every bit that dm-log would use would be in the X area).
0 0 0 0 X X X X
^
here
which hasn't been cleared properly.
As the dm-raid1 code only syncs and counts regions which have a 0 in the
'sync_bits' bitset, and only finishes when it has counted high enough, a large
number of 1's among those 'X's will cause the sync to not complete.
It is worth noting that the code uses the same bitsets for in-memory and
on-disk logs. As these bitsets are host-endian and host-sized, this means
that they cannot safely be moved between computers with
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some circumstances the LIST_VERSIONS output is truncated because the size
calculation forgets about a 'uint32_t' in each structure - but the inclusion
of the whole of ALIGN_MASK frequently compensates for the omission.
This is a quick workaround to use an upper bound. (The code ought to be fixed
to supply the actual size.)
Running 'dmsetup targets' may demonstrate the problem: when I run it, the last
line comes out as 'erro' instead of 'error'. Consequently, 'lvcreate --type
error' doesn't work.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An error path in table_load() forgets to release a table that won't now be
referenced.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver only appears on IA32 & EM64T boxes.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
scsi_get_command() attempts to write into a structure that may not have
been successfully allocated. Move this write inside the if statement that
ensures we won't panic the kernel with a NULL pointer dereference.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/cpufreq/cpufreq.c: In function `cpufreq_remove_dev':
drivers/cpufreq/cpufreq.c:696: warning: unused variable `cpu_sys_dev'
Signed-off-by: Grant Coady <gcoady@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reported by: Wayne E. Harlan
"[1.] One line summary of the problem:
When the kernel option "vga=1" is used, additional tty's (alt+control+Fx
with x=2,3,4,5, etc) do not provide the full 50 lines of output. The first
one does have 50 lines, however.
[2.] Full description of the problem/report:
These addtitional tty's show only 39 lines plus the top pixel of the 40-th
line. The remaining lines are black and not shown. Kernel version
2.6.13.4 does not show this problem."
This bug is caused by using a stale font height value on vgacon_init.
Booting with vga=1 gives an 80x50 screen with an 8x8 font. Somewhere
during the initialization, the font was changed to 8x9 and the first
vc was correctly resized to 80x44. However, the rest of the vc's were
not allocated yet, and when they were subsequently initialized, they
still used a font height of 8 (instead of 9) causing the mentioned bug.
Fix by saving the new font height to vga_video_font_height.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The shift value (amount to shift the bitmap so first pixel starts at
origin(0,0)) is incorrect. This causes corrupted characters or a kernel crash
if fontwidth is not divisible by 8 at 270 degrees, or fontheight not divisible
by 8 at 180 degrees.
Report and part of the fix contributed by Knut Petersen.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's strange enough to be looking out for anonymous pages in VM_UNPAGED areas,
let's not insert the ZERO_PAGE there - though whether it would matter will
depend on what we decide about ZERO_PAGE refcounting.
But whereas do_anonymous_page may (exceptionally) be called on a VM_UNPAGED
area, do_no_page should never be: just BUG_ON.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/net/dgrs.c: In function `dgrs_init_module':
drivers/net/dgrs.c:1598: `dgrs_pci_driver' undeclared (first use in this function)
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
