Some of the functions (like cdn_dp_dpcd_read, cdn_dp_get_edid_block)
allow to read 64KiB, but the cdn_dp_mailbox_read_receive, that is
used by them, can read only up to 255 bytes at once. Normally, it's
not a big issue as DPCD or EDID reads won't (hopefully) exceed that
value.
The real issue here is the revocation list read during the HDCP
authentication process. (problematic use case:
https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-4.4/drivers/gpu/drm/rockchip/cdn-dp-reg.c#1152)
The list can reach 127*5+4 bytes (num devs * 5 bytes per ID/Bksv +
4 bytes of an additional info).
In other words - CTSes with HDCP Repeater won't pass without this
fix. Oh, and the driver will most likely stop working (best case
scenario).
Signed-off-by: Damian Kos <dkos@cadence.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1541518625-25984-1-git-send-email-dkos@cadence.com
While adding SiI9022A support to the iwg23s board, it came
up that when the HDMI transmitter is in pass through mode the
device is not compliant with the I2C specification anymore,
as it requires a far bigger tbuf, due to a delay the HDMI
transmitter is adding when relaying the STOP condition on the
monitor i2c side of things.
When not providing an appropriate delay after the STOP condition
the i2c bus would get stuck. Also, any other traffic on the bus
while talking to the monitor may cause the transaction to fail
or even cause issues with the i2c bus as well.
I2c-gates seemed to reach consent as a possible way to address
these issues, and as such this patch is implementing a solution
based on that. Since others are clearly relying on the current
implementation of the driver, this patch won't require any DT
changes.
Since we don't want any interference during the DDC Bus
Request/Grant procedure and while talking to the monitor, we
have to use the adapter locking primitives rather than the
i2c-mux locking primitives.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541505156-8097-1-git-send-email-fabrizio.castro@bp.renesas.com
The TPO TPG110 bindings were using the DPI bindings (popular
in the fbdev subsystem) but this misses the finer points
learned in the DRM subsystem.
We need to augment the bindings for proper DRM integration:
the timings are expressed by the hardware, not put into the
device tree. I.e. this hardware is self-describing and can
report the resolutions and timings needed. It should not
be described in the device tree.
Further the device was incorrectly modeled with GPIO lines
instead of an SPI child, even though the device was using
SPI.
No known deployments of the device using device tree
exist, so it should be fine to augment the bindings.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101213256.12097-1-linus.walleij@linaro.org
I just got a new GDP Win2 device with an updated firmware, which still
requires this quirk to get the rotation right, so add the new firmware
date to the quirk matching table.
This should go to drm-misc-next.
Signed-off-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018193136.4910-1-krisman@collabora.co.uk
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/qxl/qxl_release.c: In function 'qxl_release_fence_buffer_objects':
drivers/gpu/drm/qxl/qxl_release.c:431:17: warning:
variable 'qbo' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/qxl/qxl_release.c:430:24: warning:
variable 'driver' set but not used [-Wunused-but-set-variable]
'qbo' not used since commit f2c24b83ae ("drm/ttm: flip the switch, and convert
to dma_fence")
And 'driver' never used since introduction in
8002db6336 ("qxl: convert qxl driver to proper use for reservations")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1542029556-88107-1-git-send-email-yuehaibing@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/qxl/qxl_object.c: In function 'qxl_bo_kunmap_atomic_page':
drivers/gpu/drm/qxl/qxl_object.c:189:21: warning:
variable 'map' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1541821486-40631-1-git-send-email-yuehaibing@huawei.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
The allocation for vfpriv is being leaked on an error return path,
fix this by kfree'ing it before returning.
Detected by CoverityScan, CID#1475380 ("Resource Leak")
Fixes: 6a37c49a94 ("drm/virtio: Handle context ID allocation errors")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181107203122.6861-1-colin.king@canonical.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
To reflect the (backward compatible) changes in the uabi we are bumping
the driver's version.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181112165157.32765-5-robert.foss@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
When the execbuf call receives an in-fence it will get the dma_fence
related to that fence fd and wait on it before submitting the draw call.
On the out-fence side we get fence returned by the submitted draw call
and attach it to a sync_file and send the sync_file fd to userspace. On
error -1 is returned to userspace.
VIRTGPU_EXECBUF_FENCE_FD_IN & VIRTGPU_EXECBUF_FENCE_FD_OUT
are supported at the simultaneously and can be flagged
for simultaneously.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181112165157.32765-4-robert.foss@collabora.com
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Add a new field called fence_fd that will be used by userspace to send
in-fences to the kernel and receive out-fences created by the kernel.
This uapi enables virtio to take advantage of explicit synchronization of
dma-bufs.
There are two new flags:
* VIRTGPU_EXECBUF_FENCE_FD_IN to be used when passing an in-fence fd.
* VIRTGPU_EXECBUF_FENCE_FD_OUT to be used when requesting an out-fence fd
The execbuffer IOCTL is now read-write to allow the userspace to read the
out-fence.
On error -1 should be returned in the fence_fd field.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181112165157.32765-3-robert.foss@collabora.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Refactor fence creation, add fences to relevant GPU
operations and add cursor helper functions.
This removes the potential for allocation failures from the
cmd_submit and atomic_commit paths.
Now a fence will be allocated first and only after that
will we proceed with the rest of the execution.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181112165157.32765-2-robert.foss@collabora.com
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
This patch adds support for the Primary Plane scaling.
On the Amlogic GX SoCs, the primary plane is used as On-Screen-Display
layer on top of video, and it's needed to keep the OSD layer to a lower
size as the physical display size to :
- lower the memory bandwidth
- lower the OSD rendering
- lower the memory usage
This use-case is used when setting the display mode to 3840x2160 and the
OSD layer is rendered using the GPU. In this case, the GXBB & GXL cannot
work on more than 2000x2000 buffer, thus needing the OSD layer to be kept
at 1920x1080 and upscaled to 3840x2160 in hardware.
The primary plane atomic check still allow 1:1 scaling, allowing native
3840x2160 if needed by user-space applications.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[narmstrong: fixed apply from malformed patch]
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-4-git-send-email-narmstrong@baylibre.com
In preparation to support the Primary Plane scaling, move the basic
OSD Interlace-Only scaler setup code into the primary plane atomic
update callback and handle the vsync scaler update like the overlay
plane scaling registers update.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-3-git-send-email-narmstrong@baylibre.com
The Amlogic Meson GX SoCs support an Overlay plane behind the primary
plane for video rendering.
This Overlay plane support various YUV layouts :
- YUYV
- NV12 / NV21
- YUV444 / 422 / 420 / 411 / 410
The scaler supports a wide range of scaling ratios, but for simplicity,
plane atomic check limits the scaling from x5 to /5 in vertical and
horizontal scaling.
The z-order is fixed and always behind the primary plane and cannot be changed.
The scaling parameter algorithm was taken from the Amlogic vendor kernel
code and rewritten to match the atomic universal plane requirements.
The video rendering using this overlay plane support has been tested using
the new Kodi DRM-KMS Prime rendering path along the in-review V4L2 Mem2Mem
Hardware Video Decoder up to 3840x2160 NV12 frames on various display modes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: Maxime Jourdan <mjourdan@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1541497202-20570-2-git-send-email-narmstrong@baylibre.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/sti/sti_crtc.c: In function 'sti_crtc_vblank_cb':
drivers/gpu/drm/sti/sti_crtc.c:255:22: warning:
variable 'priv' set but not used [-Wunused-but-set-variable]
It never used since introduction in
commit 9e1f05b280 ("drm/sti: rename files and functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1541818660-37168-1-git-send-email-yuehaibing@huawei.com
This is the first step into converting the meson/drm driver to use
the canvas module.
If a canvas provider node is detected in DT, use it. Otherwise,
fall back to what is currently being done.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added back priv in meson_drv_unbind()]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105104508.23090-3-mjourdan@baylibre.com
drm-next is forwarded to v4.20-rc1, and we need this to make
a patch series apply.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
We need to include the revert of commit 783195ec1c ("drm/syncobj:
disable the timeline UAPI for now v2") along with undoing the change to
drm/i915.
Fixes: 131280a162 ("drm: Revert syncobj timeline changes.")
Cc: Christian König <christian.koenig@amd.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Sean Paul <sean@poorly.run>
Cc: David Airlie <airlied@linux.ie>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181112152130.12275-1-chris@chris-wilson.co.uk
For the YUV conversion to work properly, ->x_scaling[1] should never
be set to VC4_SCALING_NONE, but vc4_get_scaling_mode() might return
VC4_SCALING_NONE if the horizontal scaling ratio exactly matches the
horizontal subsampling factor. Add a test to turn VC4_SCALING_NONE
into VC4_SCALING_PPF when that happens.
The old ->x_scaling[0] adjustment is dropped as I couldn't find any
mention to this constraint in the spec and it's proven to be
unnecessary (I tested various multi-planar YUV formats with scaling
disabled, and all of them worked fine without this adjustment).
Fixes: fc04023faf ("drm/vc4: Add support for YUV planes.")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20181109102633.32603-1-boris.brezillon@bootlin.com
Some panels need an active-low data enable (DE) signal for the RGB
interface. This requires flipping a bit in the TCON0 polarity register
when setting up the mode for the RGB interface.
Match the associated bus flag and use it to set the polarity inversion
bit for the DE signal when required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-4-contact@paulk.fr
Features such as dithering and pixel data edge configuration currently
rely on the panel registered with the TCON driver. However, bridges are
also supported in addition to panels for RGB setup.
Instead of retrieving the connector from the panel, get it from the
encoder with the dedicated helper.
Even in the case of bridges, the connector is registered with the
encoder from our driver and is accessible when iterating connectors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-3-contact@paulk.fr
Passing the encoder to the TCON RGB setup functions allows accessing the
connector from the encoder directly instead of relying on the panel.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-2-contact@paulk.fr
Until we have sorted out all problems.
v2: return -EINVAL during create if flag is set.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/260937/
Convert drm_atomic_plane_check() over to using explicit old vs. new
plane states. Avoids the confusion of "what does plane->state mean
again?".
v2: Stick to the multi-stage logic in plane_switching_crtc() (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181106191624.2207-1-ville.syrjala@linux.intel.com
Replace 'crtc->state' with the explicit old crtc state.
Actually it shouldn't matter whether we use the old or the new
crtc state here since any plane that has been removed from the
crtc since the crtc state was duplicated will have been added
to the atomic state already. That is, you can't call
drm_atomic_set_crtc_for_plane() without having the new
plane state already in hand.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101184646.14753-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Add a function to check whether there is at least one plane that
supports a specific format and modifier combination. Drivers can
use this to reject unsupported formats/modifiers in .fb_create().
v2: Accept anyformat if the driver doesn't do planes (Eric)
s/planes_have_format/any_plane_has_format/ (Eric)
Check the modifier as well since we already have a function
that does both
v3: Don't do the check in the core since we may not know the
modifier yet, instead export the function and let drivers
call it themselves
Cc: Eric Anholt <eric@anholt.net>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029183453.28541-1-ville.syrjala@linux.intel.com
It's lockless, and userspace might chance it underneath us. That's not
really a problem, all userspace gets is a slightly dysfunctional
lease with the current code. But this might change, and gcc might
decide to reload a few too many times, and then boom. So better safe
than sorry.
v2: Remove the now unused lessor_priv argument from validate_lease()
(Keith).
v3: Actually add everything ... silly me.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181105101211.22737-1-daniel.vetter@ffwll.ch
This essentially undoes
commit 39868bd766
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Oct 29 08:55:58 2013 +0000
drm: Compact booleans within struct drm_file
We do lockless access to these flags everywhere, and it's kinda not a
great idea to mix lockless and bitfields. Aside from that gcc isn't
generating great code for these.
If this ever becomes an issue size-wise, I think we need atomic_t here
and atomic bitflag ops.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102132543.16486-2-daniel.vetter@ffwll.ch
I spent a bit of time scratching heads and figuring out why the igts
don't work. Probably useful to keep this work.
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@gmail.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102132543.16486-1-daniel.vetter@ffwll.ch
This broke rendering on V3D, where we almost always have a 0
in-syncobj.
Signed-off-by: Eric Anholt <eric@anholt.net>
Fixes: 48197bc564 ("drm: add syncobj timeline support v9")
Cc: Chunming Zhou <david1.zhou@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.kernel.org/patch/10669317/
Signed-off-by: Christian König <christian.koenig@amd.com>
VGEM doesn't do anything modeset specific, so in a way exposing a
primary node is 'wrong'. At the same time, we extensively use if for
creating dumb buffers, fences, prime fd <> handle imports/exports.
To the point that we explicitly annotate the vgem fence ioctls as
DRM_RENDER_ALLOW and have an IGT test which opens the render node.
close(drm_open_driver_render(DRIVER_VGEM))
Better late than never, let's flip the switch.
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026120647.7528-1-emil.l.velikov@gmail.com
Allwinner H6 SoC has a cut down version of TCON TOP.
Add binding documentation for it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[expanded description]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-26-jernej.skrabec@siol.net
Some SoCs, such as H6, doesn't have a full-featured TCON TOP.
Add quirks support for TCON TOP.
Currently the presence of TCON_TV1 and DSI is controlled via the quirks
structure.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Fixed code style and removed unnecessary initialization]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-25-jernej.skrabec@siol.net
It turns out that TCON TOP registers in H6 SoC have non-zero reset
value. This may cause issues if bits are not changed during
configuration.
To prevent that, initialize registers to 0.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-24-jernej.skrabec@siol.net
H6 has Synopsys DWC HDMI 2.0 TX PHY.
There is no freely available documentation for it, only code found in
BSP kernel. However, judging by the code, PHY is very similar to older
Synopsys HDMI PHY described in i.MX6 documentation. Most registers seem
to be the same.
According to i.MX6 documentation, mpll settings are based on pixel clock
and are not specific to each SoC. Because of that, mpll table in this
commit is based on that documentation and not on BSP code. Other PHY
settings were derived from BSP PHY driver code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-23-jernej.skrabec@siol.net
Currently sun8i-hdmi-phy driver supports only custom PHYs connected to
DW HDMI controller. Since newest Allwinner SoCs have unmodified Synopsys
PHY, driver has to be reorganized to support them.
Variant structure is expanded to allow differentiation between custom
and Sysnopsys PHYs and to hold Synopsys PHY settings.
Since DW HDMI bridge platform data has different fields for custom and
Sysnopsys PHY, function sun8i_hdmi_phy_get_ops() is replaced with
sun8i_hdmi_phy_set_ops().
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-22-jernej.skrabec@siol.net
Currently, quirks and compatibles are sorted alphabetically. However,
they should be sorted by family release date and then alphabetically.
Fix that by moving A64 quirks and compatible to bottom. No functional
change is made.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-21-jernej.skrabec@siol.net
The Allwinner H6 SoC uses a v2.12a DesignWare HDMI controller, with
dedicated CEC and HDCP clocks added; the PHY connected is a standard
DesignWare HDMI PHY.
Add binding for it.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[added HDCP clock and reset]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-19-jernej.skrabec@siol.net
It turns out that H6 HDMI BSP kernel driver doesn't change TMDS rate at
all. At this point it is not clear whether it is just not necessary or
it would cause some kind of issues.
Add a quirk for it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-18-jernej.skrabec@siol.net
Since it is not possible to access sun8i-dw-hdmi driver private data
inside mode_valid function, make it configurable. That way different
versions of HDMI controllers can set different function, depending on
it's limitations.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-17-jernej.skrabec@siol.net
Currently supported Allwinner SoCs with DW HDMI controller have
scrambled addresses and read lock. However, that is not true in general.
For example, A80 and H6 have normal addresses and normal read access.
Move code for unscrambling addresses and unlocking read access to it's
own function and call it from init function.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181104182705.18047-16-jernej.skrabec@siol.net
