Per comments from Bjorn Andersson <bjorn.andersson@sonymobile.com>,
split DMA mask register writing as seperate patch in case we need
bi-sect in the furture.
Signed-off-by: Fengwei Yin <fengwei.yin@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Lawrence reported that git clone could make system crash on a
Qualcomm ARM soc based device (DragonBoard, 1G memory without
swap) running 64bit Debian.
It's turned out the crash is related with rx skb allocation
failure. git could consume more than 600MB anonymous memory.
And system is in extremely memory shortage case.
But driver didn't handle the rx allocation failure case. This patch
doesn't submit skb to upper layer if rx skb allocation fails.
Instead, it reuse the old skb for rx DMA again. It's more like
drop the packets if system is in memory shortage case.
With this change, git clone is OOMed instead of system crash.
Reported-by: King, Lawrence <lking@qti.qualcomm.com>
Signed-off-by: Fengwei Yin <fengwei.yin@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There is a type bug so it always returns success.
Fixes: 6fa658fd5a ('ath9k: Simplify and fix eeprom endianness swapping')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ath9k driver does not modify tx skbs, so SUPPORTS_CLONED_SKBS
flag can be set. Enabling this flag significant reduce number
of copy operation during TCP Tx. This is especially noticeable
on platforms with slower CPU (lower CPU usage brings
profits in better TCP Tx troughput results).
Tested on MIPS with 560 MHz clock
Without CLONED_SKBS flag:
TCP Tx 145 Mb/s (iperf result)
__copy_user_common consumes 12.9% of CPU (result from perf tool)
0% CPU Idle
With CLONED_SKBS flag:
TCP Tx 170 Mb/s (iperf result)
__copy_user_common consumes 1.8% of CPU (result from perf tool)
12% CPU Idle
Signed-off-by: Pawel Kulakowski <pawel.kulakowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Added a simple interface for platform to perform crash
recovery.
When firmware crashes, wil driver can notify the platform
which can trigger a crash recovery process. During
the process the platform can request a ram dump
from the wil driver as well as control when firmware
recovery will start. This interface allows the platform
to implement a more advanced crash recovery, for
example to reset dependent subsystems in proper order, or
to provide its own notifications during the recovery process.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When network interface is stopping, some resources may
be already released by the network stack, and Rx frames
cause kernel OOPS (observed one is in netfilter code)
Proper solution is to drop packets pending in reorder buffer.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use SMPS disabled as default because FW does not indicate
any support of SMPS.
This change will help STAs out that don’t support SMPS from
sticking on 1SS, since they don’t have method to change it
back to multiple chains.
This change also should not affect power consumption of STAs
supporting SMPS, because they are capable to switch the mode
to dynamic or static either at the end of frame sequence or
by using SMPS action frame.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The driver calls pci_set_mwi to enable memory-write-invalidate when it
is initialized, but does not call pci_clear_mwi when it is removed. Many
other drivers calls pci_clear_mwi when pci_set_mwi is called, such as
r8169, 8139cp and e1000.
This patch adds pci_clear_mwi in error handling and removal procedure,
which can fix the problem.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The module parameter can be used to ensure the probe succeeds thus
claiming the device and allowing post-mortem debugging in case of
firmware crash. It is only available when select CONFIG_BRCMDBG.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Module parameters are defined in several files. Move them in one
place and make them device specific or global. This makes it
easier to override device specific settings by external data like
platform data in the future.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver is being unloaded a situation can occur where the
wirelesss core (cfg80211) wants to remove the ibss, but the state
of brcmfmac has already been set to down. When an error is
returned in that situation then that will result in a stack
trace on removal of the wiphy object. This is avoided by
returning 0 when device is down on a leave_ibss call.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several features in the driver directly map to a firmware feature
listed in response of the 'cap' firmware command. For those features
this response will be examined instead of attempting individual
firmware commands.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Scheduled scan be requested to use mac randomization. This patch
checks the flags and enables the randomization if desired.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When get_station is requested for IBSS then an error will be
printed and no information will be returned. This patch adds
IBSS specific get station information function.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Obtain ipv4 address through inetaddr notification for ARP offload host
ip table configuration.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ipw2100_alloc_skb() and ipw2100_tx_send_data() do not check if mapping
dma memory succeed. The patch adds the checks and failure handling.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver supports Tx status ack feature. When hostapd/
wpa_supplicant asks for ack status of an EAPOL/ACTION
frame, driver maintains a cloned skb for the packet
until TX_STATUS event is received from firmware.
Cloned skb queue gets flushed when connection is terminated
or driver is unloaded.
Let's reduce the queue size to avoid unnecessarily
keeping memory allocated when environment is busy.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch increase the priority for some critical
messages.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some critical messages are missed until "adapter->dev"
gets initialized in mwifiex_register_dev().
We will use pr_* print message instead of mwifiex_dbg at
those places to resolve the problem.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since kzalloc can be failed in memory pressure,
it needs to be handled, otherwise NULL dereference could be happened
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The il_sensitivity_ranges is never modified, so declare it as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reported-by: Bingkuo Liu <bingkuol@vmware.com>
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The WeTelecom-WPD600N is an LTE module that, in addition to supporting most
"normal" bands, also supports LTE over 450MHz. Manual testing showed that
only interface number three replies to QMI messages.
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
"priv" is allocated with devm_kzalloc() so freeing it here with kfree()
will lead to a double free.
Fixes: 3933961682 ('fsl/fman: Add FMan MAC driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pause_time is unsigned so it can't be less than zero. The bug means
that we allow invalid pause-times.
Fixes: 57ba4c9b56 ('fsl/fman: Add FMan MAC support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We checked "err" on the lines before so we know it's zero here.
These cause a static checker warning because checking known things can
indicate a bug. Maybe there is a missing assignment or we are checking
the wrong variable.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit d79f16c046 fixed a user triggerable
scribble on free memory but added a new one which allows the user to
scribble even more and user controlled data into freed space.
As with 6pack we need to halt the queue before we free the buffers, because
the transmit logic is not protected by the semaphore.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is based on the work done by Przemek Rudy in bug 70761 at
bugzilla.kernel.org, but with some work done to disentagle and clarify
things a bit.
Similar to Przemek's work and other drivers, we're adding a padding of 16
here, but we're also disentangling mtu size calculations from max buffer
size calculations a bit, and adding ETH_HLEN to the value written into
ALX_MTU. Hopefully, with a bit more consistency and clarity, things behave
better here. Sadly, I can only test in my alx-driven E2200, which worked
just fine before this patch.
In comment #58 of bug 70761, Eugene A. Shatokhin reports that this patch
does help considerably for a ROSA Linux user of his with an AR8162 network
adapter when patched into a 4.1.x-based kernel, with several days of
normal operation where wired network previously wasn't usable without
setting MTU to 9000 as a work-around.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=70761
CC: "Eugene A. Shatokhin" <eugene.shatokhin@rosalab.ru>
CC: Przemek Rudy <prudy1@o2.pl>
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vlan is been configured, remeber the untagged mode of the vlan.
When displaying the list of configured VLANs, show the untagged attribute.
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is bridged, the bridge must be vlan aware bridge (.1Q)
or the bridging should be on top of VLAN interfaces (.1D bridge).
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize VLANs 0..4095 (Remove init for VID 4096).
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit acf673a318 fixed a user triggerable free
memory scribble but in doing so replaced it with a different one that allows
the user to control the data and scribble even more.
sixpack_close is called by the tty layer in tty context. The tty context is
protected by sp_get() and sp_put(). However network layer activity via
sp_xmit() is not protected this way. We must therefore stop the queue
otherwise the user gets to dump a buffer mostly of their choice into freed
kernel pages.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During initialization, when creating the send descriptor queues (SDQs),
we specify the CPU egress traffic class of each SDQ. The maximum number
of classes of this type is different in the two ASICs supported by this
PCI driver.
New firmware versions check this value is set correctly, which causes
errors on the Spectrum ASIC, as its max exposed egress traffic class is
lower than 7.
Solve this by setting this field to 3, which is an acceptable value for
both ASICs.
Note that we currently do not expose the QoS capabilities of the ASICs,
so setting this to an hardcoded value is OK for now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* fix IBSS which got broken over time
* new USB id for bcm43242 dongle
* arp offload configuration through inet notifier
ath9k
* add random number generator support (CONFIG_ATH9K_HWRNG)
iwlwifi
* Make scan parameters low latency aware
* Fix in the NL80211_FEATURE_FULL_AP_CLIENT_STATE state case
* Fix enable injection mode (Chaya Rachel)
* Various cleanups (Dan / Julia / myself)
* Allow to stay more time on popular channels (David Spinadel)
* Bug fixes for D0i3 (Eliad / Luca)
* Fixes for GO uAPSD (myself)
* Start of TSO support (myself)
* Rate control bug fixes (Eyal / Gregory)
* Start the work on 9000 devices (Johannes / Sara / Oren)
* Start the work on a new Tx queue allocation model (Liad)
* Debug infrastructure enhancements (Golan)
mwifiex
* add a debugfs file for chip reset
* advertise SMS4 cipher suite
* increase ap and station interface limit to 3
* enable MSI support on newer pcie devices (8897 onwards)
rtlwifi
* fix lots of module parameter usage
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWi5RxAAoJEG4XJFUm622bujQH/Rti4fRBnJcRt5EZAv/pvdIx
AGPcYQQfFbFRjzxjrcY30AYCC6OoID9n7BNtELIWabA6dQHWGJd2aebZGH85O4Eh
xgAty5CRf9E4+9MNiv+OqkL64/E6/YmSeOYiNSWl6SgRE4VYmexLXttpppImmoER
zowmtqzLSN/4l4yX5p2BVy3NAXN0R1WjYKNUXAJvJj59814upXf+XrOKCghzHIs4
2NE/aFoscscKWCSS3+MIIW4q9QWw7f8YvAdrO6k47LLkjm4+C/I5BeAlHUOEQUS7
xyoB/7KoHXlzRen8LmoL9SsqopTL2tKEjE/1f0QgLKOHXqpPRb4iKBFjsR94HJg=
=aeCM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-01-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
brcfmac
* fix IBSS which got broken over time
* new USB id for bcm43242 dongle
* arp offload configuration through inet notifier
ath9k
* add random number generator support (CONFIG_ATH9K_HWRNG)
iwlwifi
* Make scan parameters low latency aware
* Fix in the NL80211_FEATURE_FULL_AP_CLIENT_STATE state case
* Fix enable injection mode (Chaya Rachel)
* Various cleanups (Dan / Julia / myself)
* Allow to stay more time on popular channels (David Spinadel)
* Bug fixes for D0i3 (Eliad / Luca)
* Fixes for GO uAPSD (myself)
* Start of TSO support (myself)
* Rate control bug fixes (Eyal / Gregory)
* Start the work on 9000 devices (Johannes / Sara / Oren)
* Start the work on a new Tx queue allocation model (Liad)
* Debug infrastructure enhancements (Golan)
mwifiex
* add a debugfs file for chip reset
* advertise SMS4 cipher suite
* increase ap and station interface limit to 3
* enable MSI support on newer pcie devices (8897 onwards)
rtlwifi
* fix lots of module parameter usage
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc fails to see that the use of the 'last_offset' variable
in hns_nic_reuse_page() is used correctly and issues a bogus
warning:
drivers/net/ethernet/hisilicon/hns/hns_enet.c: In function 'hns_nic_reuse_page':
drivers/net/ethernet/hisilicon/hns/hns_enet.c:541:6: warning: 'last_offset' may be used uninitialized in this function [-Wmaybe-uninitialized]
This simplifies the function to make it more obvious what is
going on to both readers and compilers, which makes the warning
go away.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a PHC support to the mlx5_en driver. Use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled. This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.
The driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-4 card.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enable/disable HW timestamping for incoming and/or
outgoing packets. To enable/disable HW timestamping appropriate
ioctl should be used. Currently HWTSTAMP_FILTER_ALL/NONE and
HWTSAMP_TX_ON/OFF only are supported. Make all relevant changes in
RX/TX flows to consider TS request and plant HW timestamps into
relevant structures.
Add internal clock for converting hardware timestamp to nanoseconds. In
addition, add a service task to catch internal clock overflow, to make
sure timestamping is accurate.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A preparation step which adds support for reading the hardware
internal timer and the hardware timestamping from the CQE.
In addition, advertize device_frequency_khz HCA capability.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the SKB is cloned, or has an elevated users count, someone else
can be looking at it at the same time.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commands run in a vrf context are not failing as expected on a route lookup:
root@kenny:~# ip ro ls table vrf-red
unreachable default
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
ping: Warning: source address might be selected on device other than vrf-red.
PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.
--- 10.100.1.254 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms
Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
connect: No route to host
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bridge port attributes are offloaded to hardware when invoked with SELF
flag set, but it really makes no sense to reflect them when port is not
bridged.
Allow a user to change these attribute only when port is bridged and
initialize them correctly when joining or leaving a bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the bridge status of physical ports in the appropriate functions, to
be consistent with LAG join/leave and vPorts joining/leaving bridge.
Also, remove the error messages in these two functions, as we already
emit errors in both the single functions they call.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for us to fail when joining or leaving a bridge, so let
the user know about that by returning NOTIFY_BAD, as already done for
LAG join/leave and 802.1D bridges.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We set PVID to 1 in mlxsw_sp_port_vlan_init(), so we can remove this
statement.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cphy_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM allmodconfig fails because of the addition of the FMAN driver:
drivers/built-in.o: In function `dtsec_restart_autoneg':
binder.c:(.text+0x173328): undefined reference to `mdiobus_read'
binder.c:(.text+0x173348): undefined reference to `mdiobus_write'
drivers/built-in.o: In function `dtsec_config':
binder.c:(.text+0x173d24): undefined reference to `of_phy_find_device'
drivers/built-in.o: In function `init_phy':
binder.c:(.text+0x1763b0): undefined reference to `of_phy_connect'
drivers/built-in.o: In function `stop':
binder.c:(.text+0x176014): undefined reference to `phy_stop'
drivers/built-in.o: In function `start':
binder.c:(.text+0x176078): undefined reference to `phy_start'
The reason is that the driver uses PHYLIB, but that is a loadable
module here, and fman itself is built-in.
This patch makes it possible to configure fman as a module as well
so we don't change the status of PHYLIB in an allmodconfig kernel,
and it adds a 'select PHYLIB' statement to ensure that phylib is
always built-in when fman is.
The driver uses "builtin_platform_driver(fman_driver);", which means
it cannot be unloaded, but it's still possible to have it as a loadable
module that gets loaded once and never removed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 5adae51a64 ("fsl/fman: Add FMan MURAM support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original way is wrong, it always writes ephy reg 0x03.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY PFM register is in PHY page 0x0a44 register 0x11, not 0x14.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register for setting D3code PFM mode is MISC_1, not DLLPR.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Reviewed-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that {cpu|edmac}_to_{edmac|cpu}() functions boiled down to the mere
{cpu|le32}_to_{le32|cpu}() calls, there's no need for these functions
anymore, so just get rid of them.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 71557a37ad ("[netdrvr] sh_eth: Add SH7619 support") added support
for the big-endian EDMAC descriptors. However, it was never used and never
worked right until the recent driver fixes. I think we now can just remove
this support, it was only burdening the driver from the start. It should be
easy to do without disturbing the SH platform code, at least for now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use to_delayed_work() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver can support either all combined or all rx/tx rings. The
default is combined, but the user can now select rx/tx rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify ring memory allocation and MSIX setup to support shared or
non shared rings and do the proper mapping. Default is still to
use shared rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add logic to calculate how many shared or non shared rings can be
supported. Default is to use shared rings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support dedicated or shared completion rings, the ring
indexing and mapping are re-structured as below:
1. bp->grp_info[] array index is 1:1 with bp->bnapi[] array index and
completion ring index.
2. rx rings 0 to n will be mapped to completion rings 0 to n.
3. If tx and rx rings share completion rings, then tx rings 0 to m will
be mapped to completion rings 0 to m.
4. If tx and rx rings use dedicated completion rings, then tx rings 0 to
m will be mapped to completion rings n + 1 to n + m.
5. Each tx or rx ring will use the corresponding completion ring index
for doorbell mapping and MSIX mapping.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each bnxt_napi structure may no longer be having both an rx ring and
a tx ring. Check for a valid ring before using it.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, an rx and a tx ring are always paired with a completion ring.
We want to restructure it so that it is possible to have a dedicated
completion ring for tx or rx only.
The bnxt hardware uses a completion ring for rx and tx events. The driver
has to process the completion ring entries sequentially for the rx and tx
events. Using a dedicated completion ring for rx only or tx only has these
benefits:
1. A burst of rx packets can cause delay in processing tx events if the
completion ring is shared. If tx queue is stopped by BQL, this can cause
delay in re-starting the tx queue.
2. A completion ring is sized according to the rx and tx ring size rounded
up to the nearest power of 2. When the completion ring is shared, it is
sized by adding the rx and tx ring sizes and then rounded to the next power
of 2, often with a lot of wasted space.
3. Using dedicated completion ring, we can adjust the tx and rx coalescing
parameters independently for rx and tx.
The first step is to separate the rx and tx ring structures from the
bnxt_napi struct.
In this patch, an rx ring and a tx ring will point to the same bnxt_napi
struct to share the same completion ring. No change in ring assignment
and mapping yet.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By adding 3 separate functions to dump the different ring states.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds checking the "CRC_OK" bit at the end of packets coming
from the CC2520 radio. It also adds support for putting the radio in
promiscuous mode (in which packets are not dropped if the CRC fails).
In promiscuous mode the AUTOCRC flag is cleared so that the driver can
pass the received CRC to the monitors.
The radio now defaults to frame filtering (checking that the destination
and PANID in the incoming packet matches the local node). This matches
the other 15.4 radios and is what a user would expect to be the default.
Other changes:
1. Adds LQI calculation
2. Makes #defines for relevant bit fields in CC2520 registers
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) Prevent XFRM per-cpu counter updates for one namespace from being
applied to another namespace. Fix from DanS treetman.
2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes
Berg.
3) Remove ethernet header assumption in nft_do_chain_netdev(), from
Pablo Neira Ayuso.
4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal
Speck.
5) Fix use after free in sixpack_close and mkiss_close.
6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz.
7) natsemi doesn't check for DMA mapping errors, from Alexey
Khoroshilov.
8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin.
9) Missing initialization of needed_headroom in geneve tunnel driver,
from Paolo Abeni.
10) Fix conntrack template leak in openvswitch, from Joe Stringer.
11) Mission initialization of wq->flags in sock_alloc_inode(), from
Nicolai Stange.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
net, socket, socket_wq: fix missing initialization of flags
drivers: net: cpsw: fix error return code
openvswitch: Fix template leak in error cases.
sctp: label accepted/peeled off sockets
sctp: use GFP_USER for user-controlled kmalloc
qlcnic: fix a loop exit condition better
net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
geneve: initialize needed_headroom
ipv6: honor ifindex in case we receive ll addresses in router advertisements
addrconf: always initialize sysctl table data
ipv6/addrlabel: fix ip6addrlbl_get()
switchdev: bridge: Pass ageing time as clock_t instead of jiffies
sh_eth: fix 16-bit descriptor field access endianness too
veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.
net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card
net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card
natsemi: add checks for dma mapping errors
rhashtable: Kill harmless RCU warning in rhashtable_walk_init
openvswitch: correct encoding of set tunnel action attributes
...
"iter" is -1 at the end of the loop and not zero. It means we don't
print a warning message.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The function can return negative values in case of error.
Its result should be then tested for such case.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For devices that does not support PCI power save, force wake up
API is used. So move powersave check inside force wakeup to reduce
one level indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 1aaf8efba0 ("ath10k: disable PCI PS for QCA988X
and QCA99X0") partially reverts pci soc powersave support added by
commit 77258d409c ("ath10k: enable pci soc powersaving"). While
reverting the change, pci wake up function is called after accessing
pci registers instead of prior to access. The assumption is that chip
is woken up before accessing its registers.Though this change does not
fix any known issues, this might help to avoid unknown or low power
platform specific issues.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
prism54 checks for dma mapping errors by comparison returned address
with zero, while pci_dma_mapping_error() should be used.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Enable the FW Logger to work over the SDIO interface in addition to over UART
interface. In the new design we use fw internal memory instead of packet ram
that was used in older (wl12xx) design. This change reduces the impact on TP
and stability.
A new event was added to notify fw logger is ready for reading. Dynamic
configuration to debugfs was added as well.
Signed-off-by: Shahar Patury <shaharp@ti.com>
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY counters receiver errors and errors while idle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2015-12-29
This series contains updates to ixgbe and ixgbevf.
William Dauchy provides a fix for ixgbevf that was implemented for ixgbe,
commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI budget when multiple
queues are enabled per vector"). The issue was that the polling routine
would increase the budget for receive to at least 1 per queue if multiple
queues were present, which resulted in receive packets being processed
when the budget was 0.
Emil provides minor cleanups for ixgbevf, one being that we need to
check rx_itr_setting with == and not &, since it is not a mask. Added
QSFP PHY support in ixgbe to allow for more accurate reporting of port
settings. Fixed the max RSS limit for X550 which is 63, not 64.
Veola fixes ixgbe ethtool reporting of backplane type interfaces as
1000/10000baseT link modes, instead, report the media as KR, KX or KX4
based on the backplane interface present.
Mark cleans up redundancy in the setting of hw_enc_features that makes
it appear that X550 has more encapsulation features than other devices.
Also do not set NETIF_F_SG any longer since that is set by the
register_netdev() call. Also fixed the X550EM_x revision check, which
needs to check a value, not just a bit.
Alex Duyck fixes additional bugs in ixgbe_clear_vf_vlans(), one being
that the mask was using a divide instead of a modulus, which resulted
in the mask bit being incorrectly set to 0 or 1 based on the value of
the VF being tested. Alex also found that he was not consistent in
using the "word" argument as an offset or as a register offset, so
made the code consistently use word as the offset in the array.
v2: dropped patch 8 of the original series, as it was undoing a part of
the fix Alex Duyck was doing in patch 9 of the original series.
Dropped based on feedback from Emil (the author).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for ethtool's --get-dump option in be2net,
to retrieve FW dump. In the past when this option was not yet available,
this feature was supported via the --register-dump option as a workaround.
This patch removes support for FW-dump via --register-dump option as it is
now available via --get-dump option. Even though the
"ethtool --register-dump" cmd which used to work earlier, will now fail
with ENOTSUPP error, we feel it is not an issue as this is used only
for diagnostics purpose.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 72ef3a88fa ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd") passed a specific pf_num while issuing a
GET_PROFILE_CONFIG cmd as FW returns descriptors for all functions when
pf_num is zero. But, when pf_num is set to a non-zero value, FW does not
return the Port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.
Fixes: 72ef3a88fa ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd")
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eeh_error, fw_timeout, hw_error variables in the be_adapter structure are
not used anymore. An earlier patch that introduced adapter->err_flags to
store this information missed removing these variables.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes a line of code that changes adapter->recommended_prio
value followed by yet another assignment.
Also, the variable is used to store the vlan priority value that is already
shifted to the PCP bits position in the vlan tag format. Hence, the name of
this variable is changed to recommended_prio_bits.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(based on a jumper setting on the adapter.) In this mode, the FW image when
flashed is authenticated with a digital signature. This patch logs
appropriate error messages and return a status to ethtool when errors
relating to FW image authentication occur.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All code relating to FW cmds is in be_cmds.[ch] excepting FW flash cmd
related code. This patch moves these routines from be_main.c to be_cmds.c
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many constant definitions relating to the FW-image layout
(such as section offset values) were defined in decimal format rather than
hexa-decimal. This makes this part of the code un-readable. Also some
defines related to BE2 are labeld "g2" and defines related to BE3 are
labeled "g3". This patch cleans up all of this to make this code more
readable.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BE3 chip doesn't support VEPA mode.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF link state setting transition from "disable" to "auto" does not work
due to a bug in SET_LOGICAL_LINK_CONFIG_V1 cmd in FW. This issue could not
be fixed in FW due to some backward compatibility issues it causes with
some released drivers. The issue has been fixed by introducing a new
version (v2) of the cmd from 10.6 FW onwards. In v2, to set the VF link
state to auto, both PLINK_ENABLE and PLINK_TRACK bits have to be set to 1.
The VF link state setting feature now works on Lancer chips too from
FW ver 10.6.315.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 38506ecefa (rtlwifi: rtl_pci: Start modification for new
drivers), a bug was introduced that causes a NULL pointer dereference.
As this bug only affects the infrequently used RTL8192EE and only under
low-memory conditions, it has taken a long time for the bug to show up.
The bug was reported on the linux-wireless mailing list and also at
https://bugs.launchpad.net/ubuntu/+source/ubuntu-release-upgrader/ as
bug #1527603 (kernel crashes due to rtl8192ee driver on ubuntu 15.10).
Fixes: 38506ecefa ("rtlwifi: rtl_pci: Start modification for new drivers")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is an API consolidation only. Bool initializations should
use true and false thus bool tests don't need an explicit comparison.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is an API consolidation only. The use of kmalloc + memset to 0
is equivalent to kzalloc.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer pcie devices (8897 onwards) support MSI. This
patch enables it.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch ensures mwifiex_pcie_txbd_empty() does take care
of 8997 chipset.
Fixes: 6d85ef00d9 ("mwifiex: add support for 8997 chipset")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch corrects some information in mwifiex_pcie_card_reg()
structure for 8997 chipset
Fixes: 6d85ef00d9 ("mwifiex: add support for 8997 chipset")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At some places, ie length is truncated from u16 to u8 while
storing it to driver's internal variable. This patch fixes
the problem.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver fails to copy the module parameter for software encryption
to the locations used by the main code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The module parameter for software encryption was never transferred to
the location used by the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two of the module parameter descriptions show incorrect default values.
In addition the value for software encryption is not transferred to
the locations used by the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Two of the module parameters are listed with incorrect default values.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this driver, parameters disable_watchdog and sw_crypto are never
copied into the locations used in the main code. While modifying the
parameter handling, the copying of parameter msi_support is moved to
be with the rest.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver failed to copy parameters sw_crypto and disable_watchdog into
the locations actually used by the driver. In addition, msi_support was
initialized three times and one of them used the wrong variable. The
initialization of parameter int_clear was moved so that it is near that
of the rest of the parameters.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver has some errors in the handling of module parameters. These
include missing initialization for parameters msi_support and
disable_watchdog. In addition, neither of these parameters nor sw_crypto
are transferred into the locations used by the driver. A final fix is
adding parameter msi to the module named and description macros.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver has a number of errors in the module initialization. These
include the following:
Parameter msi_support is stored in two places - one is removed.
Paramters sw_crypto and disable_watchdog were never stored in the final
locations, nor were they initialized properly.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Device fails to connect to some AP's configured in WPA
security mode. Currently IE buffer parsing logic in driver
expects WPA IE to be present at the beginning of IE buffer.
Otherwise connection is failed with 'incompatible network
setting' error.
This patch fixes the problem by improving IE buffer parsing
logic.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's better to use world if region code from EEPROM is
unidentied instead of forcing it to FCC
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This array contains list of supported region codes.
It is changed to make it aligned with region code
to country mapping table in driver.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Default gpio and gap is downloaded to firmware while
configuring host sleep for wake on disconnect. We may
have gpio and gap modified by user.
This patch fixes the problem.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes AP sends TDLS setup response as AMSDU packet.
As driver doesn't parse it and update peer station's 11n
capability in this case, AMPDU doesn't get setup.
This patch calls mwifiex_process_tdls_action_frame() in
AMSDU Rx path to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This provides an option for user to power cycle the card.
It will be used to change the firmware without actually
rebooting the system.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During AMSDU aggregation, we are already using timestamp
value of a first packet being aggregated. This patch removes
redundant ktime_get_real() call.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Block ACK action frames are dropped in driver. This error
is expected in this case. Let's lower the priority of this
message.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hostapd is killed with Ctrl+C before cac get completed,
stop_ap handler will not be called, thus priv->wdev.cac_started
flag remains set.
Hostapd restart attempt will be failed in this case with device
busy error. This patch aborts cac in del_station handler to
handle this corner case.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Maximum supported wowlan pattern length has been increased
from 20 to 40.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wildcard prefix bytes are ignored while downloading packet
pattern to firmware. As packet offset is not adjusted
accordingly firmware end up matching the pattern at wrong
offset. The packet offset is corrected in this patch.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is needed to support WAPI functionality.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes issues observed while starting 3 different
bss simultaneously, eg, 2 AP + 1 STA or 3 AP
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ap/station interface limit has been changed to allow
creating maximum 3 interfaces.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When I had rewritten the code for ixgbe_clear_vf_vlans() it looks like I
had transitioned back and forth between using word as an offset and using
word as a register offset. As a result I honestly don't see how the code
was working before other than the fact that resetting the VLANs on the VF
like didn't do much to clear them.
Another issue found is that the mask was using a divide instead of a
modulus. As a result the mask bit was incorrectly being set to either bit
0 or 1 based on the value of the VF being tested. As a result the wrong
VFs were having their VLANs cleared if they were enabled.
I have updated the code so that word represents the offset in the array.
This way we can use the modulus and xor operations and they will make sense
instead of being performed on a 4 byte aligned value.
I replaced the statement "(word % 2) ^ 1" with "~word % 2" in order to
reduce the line length as the line exceeded 80 characters with the register
name inserted. The two should be equivalent so the change should be safe.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X550EM_x revision check needs to check a value, not just a bit.
Use a mask and check the value. Also remove the redundant check
inside the ixgbe_enter_lplu_t_x550em, because it can only be called
when both the mac type and revision check pass.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X550 allows for up to 64 RSS queues, but the driver can have max
of 63 (-1 MSIX vector for link).
On systems with >= 64 CPUs the driver will set the redirection table
for all 64 queues which will result in packets being dropped.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clean up minor redundancy in the setting of hw_enc_features that
makes it appears that X550 uniquely has more encapsulation features
than other devices. The driver only supports one more feature, so
make it look that way. No longer set NETIF_F_SG since that is set
by the register_netdev call. Thanks to Alex Duyck for noticing this
slight confusion.
Reported-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the
backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add missing QSFP PHY types to allow for more accurate reporting of
port settings.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
adapter->rx_itr_setting is not a mask so check it with == instead of &
do not default to 12K interrupts in ixgbevf_set_itr()
There should be no functional effect from these changes.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is the same patch as for ixgbe but applied differently according to
busy polling. See commit 5d6002b7b8 ("ixgbe: Fix handling of NAPI
budget when multiple queues are enabled per vector")
Signed-off-by: William Dauchy <william@gandi.net>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use to_platform_device() instead of open-coding it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix in the NL80211_FEATURE_FULL_AP_CLIENT_STATE state case (Ayala)
* Fix enable injection mode (Chaya Rachel)
* Various cleanups (Dan / Julia / myself)
* Allow to stay more time on popular channels (David Spinadel)
* Bug fixes for D0i3 (Eliad / Luca)
* Fixes for GO uAPSD (myself)
* Start of TSO support (myself)
* Rate control bug fixes (Eyal / Gregory)
* Start the work on 9000 devices (Johannes / Sara / Oren)
* Start the work on a new Tx queue allocation model (Liad)
* Debug infrastructure enhancements (Golan)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=831z
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-12-21' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Make scan parameters low latency aware (Avi Stern)
* Fix in the NL80211_FEATURE_FULL_AP_CLIENT_STATE state case (Ayala)
* Fix enable injection mode (Chaya Rachel)
* Various cleanups (Dan / Julia / myself)
* Allow to stay more time on popular channels (David Spinadel)
* Bug fixes for D0i3 (Eliad / Luca)
* Fixes for GO uAPSD (myself)
* Start of TSO support (myself)
* Rate control bug fixes (Eyal / Gregory)
* Start the work on 9000 devices (Johannes / Sara / Oren)
* Start the work on a new Tx queue allocation model (Liad)
* Debug infrastructure enhancements (Golan)
- A previous patch updated the mlx4 driver to use vmalloc when there was
not enough memory to get a contiguous region large enough for our needs,
so we need kvfree() whenever we free that item. We missed one place,
so fix that now.
- A previous patch added code to match incoming packets against a specific
device, but failed to compensate for devices that have both InfiniBand
and Ethernet ports. Fix that.
- Under certain vlan conditions, the ocrdma driver would fail to bring up
any vlan interfaces and would print out a circular locking failure. Fix
that.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ePss
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Three late 4.4-rc fixes.
The first two were very small in terms of number of lines, the third
is more lines of change than I like this late in the cycle, but there
are positive test results from Avagotech and from my own test setup
with the target hardware, and given the problem was a 100% failure
case, I sent it through.
- A previous patch updated the mlx4 driver to use vmalloc when there
was not enough memory to get a contiguous region large enough for
our needs, so we need kvfree() whenever we free that item. We
missed one place, so fix that now.
- A previous patch added code to match incoming packets against a
specific device, but failed to compensate for devices that have
both InfiniBand and Ethernet ports. Fix that.
- Under certain vlan conditions, the ocrdma driver would fail to
bring up any vlan interfaces and would print out a circular locking
failure. Fix that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/be2net: Remove open and close entry points
RDMA/ocrdma: Depend on async link events from CNA
RDMA/ocrdma: Dispatch only port event when port state changes
RDMA/ocrdma: Fix vlan-id assignment in qp parameters
IB/mlx4: Replace kfree with kvfree in mlx4_ib_destroy_srq
IB/cma: cma_match_net_dev needs to take into account port_num
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Added the PCI IDs for the BCM57301 and BCM57402 controllers.
Signed-off-by: David Christensen <davidch@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be forward compatible with future changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware will return the ring group resource when we call
hwrm_func_qcaps(). To be compatible with older firmware, use the
number of tx rings as the number of ring groups if the older firmware
returns 0. When determining how many rx rings we can support, take
the ring group resource in account as well in _bnxt_get_max_rings().
Divide and assign the ring groups to VFs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to keep track of all resources, such as rx rings, tx rings,
cmpl rings, rss contexts, stats contexts, vnics, after we have
divided them for the VFs. Otherwise, subsequent ring changes on
the PF may not work correctly.
We adjust all max resources in struct bnxt_pf_info after they have been
assigned to the VFs. There is no need to keep the separate
max_pf_tx_rings and max_pf_rx_rings.
When SR-IOV is disabled, we call bnxt_hwrm_func_qcaps() to restore the
max resources for the PF.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use local variable pf for repeated access to this pointer.
2. The 2nd argument num_vfs was unnecessarily declared as pointer to int.
This function doesn't change num_vfs so change the argument to int.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware resources required to enable NTUPLE varies depending on
how many rx channels are configured. We need to make sure we have the
resources before we enable NTUPLE. Add bnxt_rfs_capable() to do the
checking.
In addition, we need to do the same checking in ndo_fix_features(). As
the rx channels are changed using ethtool -L, we call
netdev_update_features() to make the necessary adjustment for NTUPLE.
Calling netdev_update_features() in netif_running() state but before
calling bnxt_open_nic() would be a problem. To make this work,
bnxt_set_features() has to be modified to test for BNXT_STATE_OPEN for
the true hardware state instead of checking netif_running().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hardware completes single segment rx frames, don't bother setting
up all the GRO related fields. Pass the SKB up as a normal frame.
Reviewed-by: vasundhara volam <vvolam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, no need to check for bp->rx_nr_rings as it is always >= 1. If the
allocation fails, it is not a fatal error and we can still proceed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_l4_csum_error is now incremented only when offload is enabled
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NC-SI firmware of type apeFW (10) is now supported.
Signed-off-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unnecessary "if" statement before the "for" statement:
if (x) {
for (i = 0; i < x; i++)
...
}
Also, change the ring free function to return void as it only returns 0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During remove_one, the driver should issue hwrm_func_drv_unrgtr
command to inform firmware that this function has been unloaded.
This is to let firmware keep track of driver present/absent state
when driver is gracefully unloaded. A keep alive timer is needed
later to keep track of driver state during abnormal shutdown.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlcnic_dcb_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlaue of RTL8168H PHY register "rg_saw_cnt" only valid from bit0 to bit13.
When read this register, add bitwise-anding its value with 0x3fff.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function "rtl8168h_2_hw_phy_config", there is a typo in setting
RTL8168H PHY parameter.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a new device driver for a high performance SR-IOV assisted virtual
network for IBM System p and IBM System i systems. The SR-IOV VF will be
attached to the VIOS partition and mapped to the Linux client via the
hypervisor's VNIC protocol that this driver implements.
This driver is able to perform basic tx and rx, new features
and improvements will be added as they are being developed and tested.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Ethernet MAC driver supporting the three
different types of MACs: dTSEC, tGEC and mEMAC.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Data Path Acceleration Architecture Frame Manger Port Driver.
The FMan driver uses a module called "Port" to represent the physical
TX and RX ports.
Each FMan version has different number of physical ports.
This patch adds The FMan Port configuration, initialization and
runtime control routines for both TX and RX.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Storage Profiles contain parameters that are used
by the FMan for frame reception and transmission.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Data Path Acceleration Architecture Frame Manger MAC support.
This patch adds The FMan MAC configuration, initialization and
runtime control routines.
This patch contains support for these types of MACs:
- dTSEC: Three speed Ethernet controller (10/100/1000 Mbps)
- tGEC: 10G Ethernet controller (10 Gbps)
- mEMAC: Multi-rate Ethernet MAC (10/100/1000/10000 Mbps)
Different FMan revisions have different type and number of MACs.
Signed-off-by: Igal Liberman <igal.liberman@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
