This patch replaces all instances of CONFIG_VOYAGERGX with
CONFIG_MFD_SM501. While at it we make sure the r2d code compiles
both with and without SM501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the board specific interrupt code for r2d to make
use of intc. While at it we improve the Kconfig to avoid confusion.
- Two sets of interrupt tables exist - one for R2D-1 and one for R2D-PLUS.
- R2D-1 and R2D-PLUS use the same irq constants.
- R2D-1 has AX88796 support, R2D-PLUS does not hook up that IRQ.
- R2D-PLUS has KEY support, R2D-1 does not hook up that IRQ.
- The number and order of IRQ values are disconnected from register bits.
- Interrupt sources now start from IRQ 100.
- The machvec demux function converts from irlm IRQ 0-14 to IRQ 100++.
Tested on R2D-1 and R2D-PLUS boards.
Version 2 adds CONFIG_RTS7751R2D_1 and CONFIG_RTS7751R2D_PLUS together
with intc structured as __initdata.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch reworks the intc core, implementing the following features:
- Support dual priority registers - one set and one clear register
- All 8/16/32 bit register combinations are now supported
- Both single mask and single enable bitmap register are supported
- Add code to set interrupt priority
- Speedup sense and priority configuration code
- Allocate data using bootmem, allows intc data structures to be
__initdata
- Save memory - allocated memory footprint is smaller than intc
structures
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes sure the function prototype for setup_bootmem_node() gets
included. The file setup-shx3.c does not compile otherwise for
CONFIG_NUMA=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7720 (SH3-DSP) CPU.
Signed-off by: Markus Brunner <super.firetwister@gmail.com>
Signed-off by: Mark Jonas <toertel@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we have a way of enabling the IRQs, hook up the platform
devices and wrap in to ILSEL for mapping the vectors.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds functionality for the on-board ILSEL IRQs that chain
IRL mode events. Many on-board devices (ethernet, usb, etc.) rely
on ILSEL IRQs directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the SH-X3 prototype board.
Only simple logic for the IRQ controller and the heartbeat driver
for now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
IRL doesn't always define sense registers, so don't bother trying to
iterate through the table. This ended up causing an oops on SH-X3
when using IRL mode.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is no point in keeping around the now unused intc2 code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the sh-specific voyagergx interrupt code to make use
of intc. A lot of "interesting" old cruft gets replaced with intc tables
and some simple demux code.
- All interrupt sources in the sm501 data sheet are now in the header.
- The number and order of IRQ values are disconnected from register bits.
- Interrupt sources now start from IRQ 200.
- set_irq_chained_handler() is now used to hook up the demux function.
In the future it would probably make sense to move the interrupt demuxer
into into the mfd driver, but this is probably a nice step in the right
direction until that happens.
Tested on a R2D-1 board using the serial port hooked up to the sm501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds single bitmap register support to intc. The current
code only handles 16 and 32 bit registers where a set bit means
interrupt enabled, but this is easy to extend in the future.
The INTC_IRQ() macro is also added to provide a way to hook in
interrupt controllers for FPGAs in boards or companion chips.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes redundant interrupt code for the shmin board which
is using a sh770x processor and 4 IRQ lines as individual interrupts
(IRQ-mode).
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes redundant board specific interrupt code for boards
using sh775x processors and 4 IRQ lines in "Individual Interrupt Mode"
aka IRLM.
Three boards are affected: sh03, snapgear and titan.
The right way to do this is to use cpu specific code provided by intc.
A nice side effect is that sh03 now compiles, board not BROKEN any more.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All SH-4 parts have a 4-digit year, while the SH-3 parts typically
only use a 2-digit one. The SH7705, SH7710, and SH7712 SH-3 parts
however opted to extend it to 4-digit and still look and act like
an SH-3 RTC in all other ways.
This adds a capability flag (RTC_CAP_4_DIGIT_YEAR) that these
corner-case CPU subtypes can set in their platform data and cleans
up some of the ifdef mess in the driver as a result.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for x3 from
intc2 to intc. New vectors are also added to match the preliminary
information.
Use plat_irq_setup_pins() to select between IRQ and IRL mode for IRQ0-3.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The intc tables for sh3 currently contain a typo where the bit
fields in IPRD are mixed up for IRQ4 and IRQ5. This patch makes
sure the correct bit fields are used - all according to the
datasheets.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The new intc code handles IRQ3 and IRQ7 in the cpu specific code
already, so there is no reason to duplicate that here.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for sh7760
from ipr + intc2 to intc. New vectors are also added to match the
information provided by the datasheet.
Vectors for IRQ4-IRQ7 are enabled by default. Use plat_irq_setup_pins()
if pins IRL0-3 should be used in IRLM mode.
The patch also adds the SIM block to the serial port platform data.
Version two of this patch fixes MMCIF problems reported by Manuel Lauss.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for sh7785
from intc2 to intc. New vectors are also added to match the information
provided by the datasheet.
No IRQ/IRL pin vectors are enabled by default. Use plat_irq_setup_pins()
to select between IRL and IRQ mode.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This reworks the cache mode configuration in Kconfig, and allows for
explicit selection of write-back/write-through/off configurations.
All of the cache flushing routines are optimized away for the off
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure that the sh7710 specific ipsec vector is missing
if building for a sh7712. All according to the datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a few missing vectors for sh7707. The only interrupt
controller differences between sh7707 and sh7709 seem to be added
vectors for one LCD controller and two PCMCIA slots.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch unifies the cpu specific interrupt setup code for
sh7706, sh7707, sh7708 and sh7709 and moves the code into a new
file called setup-sh770x.c. It makes sense to share the setup code
between these processors because most hardware blocks are identical
from a software point of view. With this patch the sh770x processors
now have a complete set of vectors that match with the information
provided by the data sheets. This is a big improvement for sh7708.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also unifies the platform device setup code which means
that the rtc driver now has platform data for all sh770x processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code
for sh7710 from ipr to intc. While at it new vectors are added
to match the information provided by the datasheet. Version two
simplifies the Kconfig part.
Vectors for IRQ4 and IRQ5 are enabled by default. Use
plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7710 specific platform data for the rtc
driver. The base address of SCIF1 is adjusted to match the
datasheet.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch converts the cpu specific interrupt setup code for
sh7705 from ipr to intc. While at it new vectors are added to
match the information provided by the datasheet.
Vectors for IRQ4 and IRQ5 are enabled by default.
Use plat_irq_setup_pins() if pins IRQ0-3 should be used in IRQ mode.
This patch also adds sh7705 specific platform data for the rtc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a plat_irq_setup() symbol for sh4-202. Without
this fix it is impossible to build a working kernel using the
microdev_defconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Older versions of binutils do not support -Wa,-isa= tuning, which is
something we rely on for enabling DSP opcode support on the newer
parts. SH3-DSP parts can still be handled with -Wa,-dsp even if the
newer parts require the newer versions of binutils for supporting the
new opcodes.
This was broken in -rc1 when the SH4AL-DSP support was being reworked,
and is needed to get SH3-DSP working with older toolchains again.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It seems we have gained an extraneous trailing ';' on one of the
wait loops in scif_sercon_putc(). Although this is completely
benign as the apparent payload is also the empty statement, it
invites error in the future. Clean it up now.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that __initmv references the machvec section unconditionally
there have been cases where folks have been mistakenly flagging
non-machvec structures with the machvec section attribute (presumably
to shut up modpost). This leads to obscure breakage in earlyprintk
amongst other places and is rather non-obvious.
Add a simple sanity check to try and catch __initmv misuse and
panic early.
Reported-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When generic_ptrace_peekdata() was merged, the break for these cases
ended up getting dropped, which lead to each PEEKTEXT/PEEKDATA op leaking
in to PEEKUSR and get_user_pages() always -EFAULTing. Add the break back
in.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes up the defconfig for various sh7751r based boards
by updating them to the single cpu subtype CONFIG_CPU_SUBTYPE_SH7751R.
The following sh4 boards are updated: hs7751rvoip, landisk, lboxre2,
systemh, titan.
The current defconfigs with two subtypes defined trigger a configuration
bug which result in kernel configurations with missing board support
code. We end up with kernels without board code and with generic machvec
only.
So we need this patch to make sure the board code gets compiled in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes sure cf support is enabled on R2D-PLUS but disabled
on R2D-1. Without this fix R2D-1 boards hang on bootup.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
- Disable CONFIG_SH_DMA to avoid boot up freeze on R2D-1
- Disable CONFIG_SH_STANDARD_BIOS to support R2D-PLUS boot loaders
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updated the snapgear defconfig to get a booting kernel.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-X3 has the FPU exceptions on different vectors completely,
patch in do_fpu_state_restore() to the proper vectors.
Results in a much happier userspace.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When reading the cached TTB value and extracting the pgd, we
accidentally applied a __va() to it and bumped it off in to bogus
space which ended up causing multiple faults in the error path.
Fix it up so unhandled faults don't do strange and highly unorthodox
things when oopsing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
fault-nommu defines the page fault handler stubs for SH-3/4 parts,
but is not needed on SH-2/SH-2A now that the entry code has been
logically separated.
Add it in for SH-3 and SH-4 explicitly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We were missing the trace_hardirqs_on() instrumentation in the nommu
case, resync with the MMU version of the page fault handler to have
this behaving consistently. Also explicitly re-enable IRQs now that
the assembly code isn't doing it for us any more.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the SH-3/4 TLB access violation path we were enabling IRQs before
the call in to trace_hardirqs_on(), which ended up triggering:
if (DEBUG_LOCKS_WARN_ON(!irqs_disabled()))
return;
in kernel/lockdep.c:2031. Fix this up by removing the early re-enable,
we were already re-enabling IRQs post-trace_hardirqs_on() already, so
the semantics are now as was initially intended.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Do not follow the frame pointers (/proc/X/task/1/stat) unless we were
compiled with them.
Signed-off-by: David McCullough <david_mccullough@au.securecomputing.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
