With common clock framework, it is must to call clk_{un}prepare() before/after
clk_{dis}enable. This patch fixes this for SPEAr timer.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain GPT Synthesizers. Their Fout is derived from
following equations:
Fout= Fin/((2 ^ (N+1)) * (M+1))
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain Fractional Synthesizers. Their Fout is derived from
following equations:
Fout = Fin / (2 * div) (division factor)
div is 17 bits:-
0-13 (fractional part)
14-16 (integer part)
div is (16-14 bits).(13-0 bits) (in binary)
Fout = Fin/(2 * div)
Fout = ((Fin / 10000)/(2 * div)) * 10000
Fout = (2^14 * (Fin / 10000)/(2^14 * (2 * div))) * 10000
Fout = (((Fin / 10000) << 14)/(2 * (div << 14))) * 10000
div << 14 is simply 17 bit value written at register.
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain Auxiliary Synthesizers. Their Fout is derived based on
values of eq, x and y.
Fout from synthesizer can be given from two equations:
Fout1 = (Fin * X/Y)/2 EQ1
Fout2 = Fin * X/Y EQ2
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
All SPEAr SoC's contain PLLs. Their Fout is derived based on following equations
- In normal mode
vco = (2 * M[15:8] * Fin)/N
- In Dithered mode
vco = (2 * M[15:0] * Fin)/(256 * N)
pll_rate = vco/2^p
vco and pll are very closely bound to each other,
"vco needs to program: mode, m & n" and "pll needs to program p",
both share common enable/disable logic and registers.
This patch adds in support for this type of clock.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Mike Turquette <mturquette@ti.com> has asked me to take the clock
changes through the arm-soc tree while there are still so many
inderdependencies, so this is the entire branch.
* depends/clk/clk-next: (30 commits)
clk: add a fixed factor clock
clk: mux: assign init data
clk: remove COMMON_CLK_DISABLE_UNUSED
clk: prevent spurious parent rate propagation
MAINTAINERS: add entry for common clk framework
clk: clk_set_rate() must fail if CLK_SET_RATE_GATE is set and clk is enabled
clk: Use a separate struct for holding init data.
clk: constify parent name arrays in macros
clk: remove trailing whitespace from clk.h
clk: select CLKDEV_LOOKUP for COMMON_CLK
clk: Don't set clk->new_rate twice
clk: clk-private: Add DEFINE_CLK macro
clk: clk-gate: Create clk_gate_endisable()
clk: Fix typo in comment
clk: propagate round_rate for CLK_SET_RATE_PARENT case
clk: pass parent_rate into .set_rate
clk: always pass parent_rate into .round_rate
clk: basic: improve parent_names & return errors
clk: core: copy parent_names & return error codes
clk: Constify parent name arrays
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Having fixed factors/dividers in hardware is a common pattern, so
add a basic clock type doing this. It basically describes a fixed
factor clock using a nominator and a denominator.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
[mturquette@linaro.org: constify parent_names in static init macro]
[mturquette@linaro.org: copy/paste bug from mux in static init macro]
[mturquette@linaro.org: fix error handling in clk_register_fixed_factor]
[mturquette@linaro.org: improve division accuracy; thanks to Saravana]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The original conversion to struct clk_hw_init failed to add the pointer
assignment in clk_register_mux.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Exposing this option generates confusion and incorrect behavior for
single-image builds across platforms. Enable this behavior permanently.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Saravana Kannan <skannan@codeaurora.org>
Patch 'clk: always pass parent_rate into .round_rate' made a subtle
change to the semantics of .round_rate. It is now expected for the
parent's rate to always be passed in, simplifying the implemenation of
various .round_rate callback definitions.
However the patch also introduced a bug in clk_calc_new_rates whereby a
clock without the CLK_SET_RATE_PARENT flag set could still propagate a
rate change up to a parent clock if the the .round_rate callback
modified the &best_parent_rate value in any way.
This patch fixes the issue at the framework level (in
clk_calc_new_rates) by specifically handling the case where the
CLK_SET_RATE_PARENT flag is not set.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
The common clock framework allocates clocks dynamically. Provide a
set of helpers to streamline the clkdev registration of the clock
lookups to avoid repetitive code sequences.
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is well documented but isn't implemented. clk_set_rate() must check if
flags have CLK_SET_RATE_GATE bit set and is enabled too.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Create a struct clk_init_data to hold all data that needs to be passed from
the platfrom specific driver to the common clock framework during clock
registration. Add a pointer to this struct inside clk_hw.
This has several advantages:
* Completely hides struct clk from many clock platform drivers and static
clock initialization code that don't care for static initialization of
the struct clks.
* For platforms that want to do complete static initialization, it removed
the need to directly mess with the struct clk's fields while still
allowing to statically allocate struct clk. This keeps the code more
future proof even if they include clk-private.h.
* Simplifies the generic clk_register() function and allows adding optional
fields in the future without modifying the function signature.
* Simplifies the static initialization of clocks on all platforms by
removing the need for forward delcarations or convoluted macros.
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
[mturquette@linaro.org: kept DEFINE_CLK_* macros and __clk_init]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergman <arnd.bergmann@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Shawn Guo <shawn.guo@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Richard Zhao <richard.zhao@linaro.org>
Cc: Saravana Kannan <skannan@codeaurora.org>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: Deepak Saxena <dsaxena@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
parent name array is now expected to be const char *, make
the relevent changes in the clk macros which define
default clock types.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Using the common clock infrastructure without the common clkdev code makes
little sense, so select CLKDEV_LOOKUP for COMMON_CLK.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
if (!clk->ops->round_rate && (clk->flags & CLK_SET_RATE_PARENT)) is true, then
we don't need to set clk->new_rate here, as we will call clk_calc_subtree()
afterwards and it also sets clk->new_rate.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
All macros used for creating different kind of clocks have similar code for
initializing struct clk. This patch removes those redundant lines and create
another macro DEFINE_CLK.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch tries to remove duplicate code for clk_gate clocks. This creates
another routine clk_gate_endisable() which will take care of enable/disable
clock with knowledge of CLK_GATE_SET_TO_DISABLE flag.
It works on following logic:
For enabling clock, enable = 1
set2dis = 1 -> clear bit -> set = 0
set2dis = 0 -> set bit -> set = 1
For disabling clock, enable = 0
set2dis = 1 -> set bit -> set = 1
set2dis = 0 -> clear bit -> set = 0
So, result is always: enable xor set2dis.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
CLK_MUX_INDEX_BIT is mistakenly written as CLK_MUX_INDEX_BITWISE in comment. Fix
it.
CLK_GATE_SET_TO_DISABLE is mistakenly written as CLK_GATE_SET_DISABLE in
comment. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Need to propagate round_rate call for the clk that has no .round_rate
operation but with flag CLK_SET_RATE_PARENT set.
For example, clk_mux is a clk with no .round_rate operation. However,
it could likely be in a clk_set_rate propagation path, saying it has
parent clk who has .round_rate and .set_rate operations.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
For most of .set_rate implementation, parent_rate will be used, so just
like passing parent_rate into .recalc_rate, let's pass parent_rate into
.set_rate too.
It also updates the kernel doc for .set_rate ops.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The parent_rate will likely be used by most .round_rate implementation
no matter whether flag CLK_SET_RATE_PARENT is set or not, so let's
always pass parent_rate into .round_rate.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch is the basic clk version of 'clk: core: copy parent_names &
return error codes'.
The registration functions are changed to allow the core code to copy
the array of strings and allow platforms to declare those arrays as
__initdata.
This patch also converts all of the basic clk registration functions to
return error codes which better aligns them with the existing clk.h api.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch cleans up clk_register and solves a few bugs by teaching
clk_register and __clk_init to return error codes (instead of just NULL)
to better align with the existing clk.h api.
Along with that change this patch also introduces a new behavior whereby
clk_register copies the parent_names array, thus allowing platforms to
declare their parent_names arrays as __initdata.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Drivers should be able to declare their arrays of parent names as const
so the APIs need to accept const arguments.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[mturquette@linaro.org: constified gate]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The comment is inaccurate (it actually ends the CONFIG_COMMON_CLK
section, there's no else) and given that we've just got a single level
of ifdef isn't really needed anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Most users of clk_get_rate() actually assume a non zero
return value as a valid rate returned. Returing -EINVAL
might confuse such users, so make it instead return zero
on error.
Besides the return value of clk_get_rate seems to be
'unsigned long'.
Signed-off-by: Rajendra nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Besides the static initialization, the clk_ops of basic clks could
also be used by particular clk type being subclass of the basic clks.
For example, clk_busy_divider has the same clk_ops as clk_divider,
except it has to wait for a busy bit before return success with
.set_rate. clk_busy_divider will somehow reuse clk_ops of clk_divider.
Since clk-provider.h is included by clk-private.h, it's safe to move
those clk_ops declaration of basic clks form clk-private.h into
clk-provider.h, so that implementation of clks like clk_busy_divider
above do not need to include clk-private.h to access those clk_ops.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clk_ops of basic clks should have "const" to match the definition
in "struct clk" and clk_register prototype.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It makes no sense to have EXPORT_SYMBOL_GPL on static functions.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Change clk_register_mux to use kzalloc, just like what all other basic
clk registration functions do.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Documentation/clk.txt has some handsome ASCII art outlining which
clk_ops are mandatory for a given clock, given the capability of the
hardware. Enforce those mandates with sanity checks in __clk_init.
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is possible to call clk_set_rate on a clock with a NULL parent. One
such example is an adjustable-rate root clock. Ensure that
clk_calc_new_rates does not dereference parent without checking first
and also handle the corner cases gracefully.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some static inline dummy functions were left over from before the clock
core was consolidated from several C files down to one. Remove them.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove old and misleading documentation from the previous clk_set_rate
implementaion.
Reported-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Otherwise cpu_active_mask will not set, which lead to other issue.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Konrad Eisele <konrad@gaisler.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The major fixes here are:
* Build fix for omap_hsmmc with OF against 3.4-rc1.
* Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3,
which broke hotplug card detection when UNSAFE_RESUME is set.
* Fix a race condition in omap_hsmmc with runtime PM.
* Fix two libertas SDIO-powered-resume regressions.
Also small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Zl8K
-----END PGP SIGNATURE-----
Merge tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC fixes from Chris Ball:
- Build fix for omap_hsmmc with OF against 3.4-rc1.
- Fix CONFIG_MMC_UNSAFE_RESUME semantics regression against 3.3, which
broke hotplug card detection when UNSAFE_RESUME is set.
- Fix a race condition in omap_hsmmc with runtime PM.
- Fix two libertas SDIO-powered-resume regressions.
- Small fixes for discard/sanitize, dw_mmc, cd-gpio and esdhc-imx.
* tag 'mmc-fixes-for-3.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc:
mmc: core: Do not pre-claim host in suspend
mmc: dw_mmc: prevent NULL dereference for dma_ops
mmc: unbreak sdhci-esdhc-imx on i.MX25
mmc: cd-gpio: Include header to pickup exported symbol prototypes
mmc: sdhci: refine non-removable card checking for card detection
mmc: dw_mmc: Fix switch from DMA to PIO
mmc: remove MMC bus legacy suspend/resume method
mmc: omap_hsmmc: Get rid of of_have_populated_dt() usage
mmc: omap_hsmmc: build fix for CONFIG_OF=y and CONFIG_MMC_OMAP_HS=m
mmc: fixes for eMMC v4.5 sanitize operation
mmc: fixes for eMMC v4.5 discard operation
Pull media fixes from Mauro Carvalho Chehab:
- Fixes a regression at DVB core when switching from DVB-S2 to DVB-S on
Kaffeine (Fedora 16 Bugzilla #812895);
- Fixes a mutex unlock at an error condition at drx-k;
- Fix winbond-cir set mode;
- mt9m032: Fix a compilation breakage with some random Kconfig;
- mt9m032: fix two dead locks;
- xc5000: don't require an special firmware (that won't be provided by
the vendor) just because the xtal frequency is different;
- V4L DocBook: fix some typos at multi-plane formats description.
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] xc5000: support 32MHz & 31.875MHz xtal using the 41.024.5 firmware
[media] V4L: mt9m032: fix compilation breakage
[media] V4L: DocBook: Fix typos in the multi-plane formats description
[media] V4L: mt9m032: fix two dead-locks
[media] rc-core: set mode for winbond-cir
[media] drxk: Does not unlock mutex if sanity check failed in scu_command()
[media] dvb_frontend: Fix a regression when switching back to DVB-S
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gHlK
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
pfm_vm_munmap() is simply vm_munmap() and pfm_remove_smpl_mapping()
always get current as the first argument.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... since exit_mmap() is coming and it will munmap() everything anyway.
In all other cases aio_free_ring() has ctx->mm == current->mm; moreover,
all other callers of vm_munmap() have mm == current->mm, so this will
allow us to get rid of mm argument of vm_munmap().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Since SDIO drivers may want to do some SDIO operations in their suspend
callback functions, we must not keep the host claimed when calling them.
Daniel Drake reported that libertas_sdio encountered a deadlock in its
suspend function.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Tested-by: Daniel Drake <dsd@laptop.org>
[stable@: please apply to 3.2-stable and 3.3-stable]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now, dma_ops is assumed that use the IDMAC. But if dma_ops is assigned
the pdata->dma_ops, we didn't ensure that callback function is defined.
If the callback isn't defined, then we should run in PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This was broken by me in 37865fe915
("mmc: sdhci-esdhc-imx: fix timeout on i.MX's sdhci") where more
extensive tests would have shown that read or write of data to the
card were failing (even if the partition table was correctly read).
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
