In some blade systems using the 5706 serdes, the hardware sometimes
does not properly generate link down interrupts. We add a workaround
in the driver's timer to force a link-down when some PHY registers
report loss of SYNC.
The parallel detect logic is cleaned up slightly to better integrate
the workaround.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is more correct to get the status block from the bnx2_napi struct
instead of the bnx2 struct. It happens that they are the same in this
case because we are using the first MSIX vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip has problem running in this mode and needs to be disabled.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/iwlwifi/iwl-3945.c: In function 'iwl3945_add_radiotap':
drivers/net/wireless/iwlwifi/iwl-3945.c:269: warning: format '%d' expects type 'int', but argument 3 has type 'long unsigned int'
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rfkill code which caused a use-after-free bug. Thanks to David
Woodhouse for spotting this out.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas: re-pepper debug statementThe recent fluff of updates
didn't put proper lbs_deb_enter/leave calls into the source code.
Add them where appropriate.
Also contains some whitespace changes.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The CF card only has a very old firmware (5.0.16p0). This firmware doesn't
know anything about mesh config. However, current code blindly calls
mesh_config when the card is inserted. So check the firmware version before
issuing this command.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always shows the firmware release.
Also converts the firmware release into something that is easily comparable.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
boot2_version is purely USB specific, so move it to struct if_usb_card.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
netif_rx should be called only from interrupt context. if_cs and if_sdio receive
packets from other contexts, and thus should call netif_rx_ni.
Signed-off-by: Marc Pignat <marc.pignat@hevs.ch>
Acked-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The << and >> operators need space on each side.
Cc: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The external iwlwifi driver comes with a README file that is
referenced by the Kconfig. This README is not present in the
driver included in the kernel. Remove references to this
documentation.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch renames iwl3945_rate_scale_priv to iwl3945_rs_sta as it
better represents the purpose of this variable.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1, This patch renames iwl4965_rate_scale_priv to iwl4965_lq_sta.
This type represents a station's link quality.
2. The names of the variables of this type were rs_priv, lq_data, lq, crl
across the file. All are now unified under the name lq_sta.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds iwl_free_fw_desc ucode helper function.
It also moves ucode helper functions to iwl-helpers.h.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After we delay device initialization until interface up, there are more
conditions for the hardware rf_kill switch states during suspend and
resume. For example, before suspend we can have interface up or down,
rf_kill enable or disable; before resume we can have rf_kill enable or
disable. So there are totally 2^3 = 8 conditions to handle. This patch
addressed this problem and makes sure every condition works correctly.
This patch also merges the device suspend and resume handlers with the
mac_start and mac_stop code since they are basically doing the same
thing.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the firmware loading (read firmware from disk and load
it into the device SRAM) from pci_probe time to the first network
interface open time. There are two reasons for doing this:
1. To support kernel buildin iwlwifi drivers. Because kernel initializes
network devices subsystem before hard disk and SATA subsystem, it is
impossible to get the firmware image from hard disk in the PCI probe
handler. Thus delaying the firmware loading into the network
interface open time is the way to go. Note, we only read the firmware
image from hard disk the first time the interface is open. After this
is succeeded, we cache the firmware image into the host memory. This
is a performance gain when user open and close the interface multiple
times and is necessary for device suspend and resume.
2. For better power saving. When the iwlwifi modules are loaded (or
buildin the kernel) but the wireless network interface is not being
used, it is a good practice the wireless device consumes as less
power as possible. Unloading the firmware from the wireless device
and unregister the driver's interrupt handler in the network
interface close handler provides users a way to achieve this. User
space network configuration tools (i.e NetworkManager) can also
contribute here when it detects a wired cable is connected and
close the wireless interface automatically.
This patch also includes the pci_save/restore_state() fixed by Ian Schram
upon the first version.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Ian Schram <ischram@telenet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document scan command.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes iwl4965_tx_cmd function and splits its content to
iwl4965_hw_build_tx_cmd_rate, iwl4965_build_tx_cmd_basic,
and iwl4965_tl_get_stats function. The latest one will be deprecated
when traffic load will move to rate scale module.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves iwl4965_get_dma_hi_address function to iwl-headers.h
as iwl_get_dma_hi_address. This function will be used in more chipsets
than only 4965.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This function removes redundant code in iwl4965_tx_cmd
function, leftovers of previous design.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds code and table data for channel switching on NPHYs.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds some code to init the 2055 radio.
This patch adds two files "tables_nphy.h" and "tables_nphy.c"
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the register definitions for the Broadcom 2055 N-radio.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert optional struct size checks to non-optional compile-time checks.
Furthermore BUILD_BUG_ON() which will be optimized away by the compiler.
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for new firmware.
Old firmware is still supported until July 2008.
To get new firmware, go to
ftp://ftp.linksys.com/opensourcecode/wrt150nv11/1.51.3/
and download the tarball. We don't have a smaller tarball, yet.
That will be fixed later.
You can extract firmware out of the "wl_ap.o" file contained
in this tarball using latest fwcutter. You must pass the option
--unsupported to fwcutter.
Fwcutter-010 with official support for a new firmware image will
be released soon.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes reading of the high 16 bits of the radio ID
on new devices. 2055 radios want lo16 to be read first.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For TX rings the queue_idx should start at
IEEE80211_TX_QUEUE_DATA0 and for each followup
ring this index needs to be increased.
For the RX ring the queue_idx should be set
to 0. We don't need to initialize the tx_params.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2500usb and rt73usb data and desc pointer initialization
was incorrect because it was using uninitialized variables
to determine the length.
In addition rt2500usb used skb_pull and removed the ieee80211
from each received frame instead of using skb_trim to remove
the device descriptor from the frame.
Finally this also fixes the descriptor override when 4 byte
aligning occured. We still need a completely valid descriptor
when using the TX/RX dumping capabilities in debugfs.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds the initval filenames for the N-PHY firmware.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the length of the variable section of the beacon instead of the
whole beacon length for bounds checking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This queues frames flagged as "send after DTIM" by mac80211
on the special multicast queue. The firmware will take care
to send the packet after the DTIM.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes uploading of the beacon data and writing of the
TIM and DTIM offsets.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch (based on Ron Rindjunsky's) creates a framework for
a unified way to pass BSS configuration to drivers that require
the information, e.g. for implementing power save mode.
This patch introduces new ieee80211_bss_conf structure that is
passed to the driver via the new bss_info_changed() callback
when the BSS configuration changes.
This new BSS configuration infrastructure adds the following
new features:
* drivers are notified of their association AID
* drivers are notified of association status
and replaces the erp_ie_changed() callback. The patch also does
the relevant driver updates for the latter change.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mattias Nissler's "clean up rate selection" patch incorrectly changes
the behavior of txrate setting in sta_info. This patch backs out parts
of the rate selection consolidation in order to fix this issue for now.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch enables the A-MPDU Rx flow. it contains several
adjustments to new mac80211 A-MPDU Rx flow.
Signed-off-by: Ron Rindjunsky <ron.rindjunsky@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an oops which was introduced as a regression by
commit fd640775bd16e1df50c867cc547af0, on the patch titled,
"mac80211: dont use interface indices in drivers".
ieee80211_generic_frame_duration() now relies on sdata->flags which
itself gets set upon bringing the interface up. We check for the
virtual interface now before setting the rate duration registers.
After the mode changes are introduced onto mac80211 we should revisit
these changes.
This patch was tested on the following cards:
1) BG card:
Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43)
RF2112A 2GHz radio found (0x46)
2) ABG card:
Atheros AR5213A chip found (MAC: 0x59,PHY: 0x43)
RF5112A multiband radio found (0x36)
Signed-off-by: Luis R. Rodriguez <mcgrof@winlab.rutgers.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch gets rid of the if_id stuff where possible in favour of
a new per-virtual-interface structure "struct ieee80211_vif". This
structure is located at the end of the per-interface structure and
contains a variable length driver-use data area.
This has two advantages:
* removes the need to look up interfaces by if_id, this is better
for working with network namespaces and performance
* allows drivers to store and retrieve per-interface data without
having to allocate own lists/hash tables
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds a mac80211 based wireless driver for the rtl8180 and
rtl8185 PCI wireless cards. Also included are some rtl8187 changes
required due to the relationship between that driver and this one.
Michael Wu is primarily responsible for the initial driver and rtl8185
support. Andreas Merello provided the additional rtl8180 support.
Thanks to Jukka Ruohonen for the donating a rtl8185 card! It was very
helpful for the rtl8225z2 code.
The Signed-off-by information below is collected from the individual
patches submitted to wireless-2.6 before merging this driver upstream.
Signed-off-by: Andrea Merello <andreamrl@tiscali.it>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
add ath5k wireless driver
Portions of this driver are covered by one or both of the ISC and
3-clause BSD licenses. Specific license information is cited at the top
of each file.
Acked-by and Signed-off-by information is collected from individual
patches as collected in the wireless-2.6 tree prior to upstream
submission.
Acked-by: Matthew W. S. Bell <mentor@madwifi.org>
Acked-by: Michael Taylor <mike.taylor@apprion.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bradley M. Kuhn <bkuhn@softwarefreedom.org>
Signed-off-by: Bruno Randolf <bruno@thinktube.com>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Francesco Gringoli <francesco.gringoli@ing.unibs.it>
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Karen Sandler <karen@softwarefreedom.org>
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Matt Norwood <norwood@softwarefreedom.org>
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Richard Fontana <fontana@softwarefreedom.org>
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Ulrich Meis <meis@nets.rwth-aachen.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the third PCMCIA ID string specifies the MAC chip, the fourth ID
string doesn't need to be matched. Even if it's different, it will be
compatible with the driver.
This ensures that other different revisions of the card will be
supported.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a sparse warning about weird locking.
The spinlock is not needed, so simply remove it.
This also adds some sanity checks to the PHY and radio locking
to protect against recursive locking.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
