Add helper to libbpf for recognizing maps which should not have
ifindex set when program is loaded. These maps only contain
host metadata and therefore are not marked for offload, e.g.
the perf event map.
Use this helper in bpf_prog_load_xattr().
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Sometimes program section names don't match with libbpf's expectation.
In particular XDP's default section names differ between libbpf and
iproute2. Allow users to pass program type on command line. Name
the types like the libbpf expected section names.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
libbpf can guess program type based on ELF section names. As libbpf
becomes more popular its association between section name strings and
types becomes more of a standard. Allow libbpf users to use the same
logic for matching strings to types, e.g. when the string originates
from command line.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Acked-by: Andrey Ignatov <rdna@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Extend the bpftool prog load command to also accept "dev"
parameter, which will allow us to load programs onto devices.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Add a new macro for printing more informative message than straight
usage() when parameters are missing, and use it for prog do_load().
Save the object and pin path argument to variables for clarity.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Currently the test only checks errors, not warnings, so save typing
and prefix the extack messages with "Error:" inside the check helper.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Trivial removal of duplicated "mode" in error message.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Jiong Wang says:
====================
NFP supports u16 and u32 multiplication. Multiplication is done 8-bits per
step, therefore we need 2 steps for u16 and 4 steps for u32.
We also need one start instruction to initialize the sequence and one or
two instructions to fetch the result depending on either you need the high
halve of u32 multiplication.
For ALU64, if either operand is beyond u32's value range, we reject it. One
thing to note, if the source operand is BPF_K, then we need to check "imm"
field directly, and we'd reject it if it is negative. Because for ALU64,
"imm" (with s32 type) is expected to be sign extended to s64 which NFP mul
doesn't support. For ALU32, it is fine for "imm" be negative though,
because the result is 32-bits and here is no difference on the low halve
of result for signed/unsigned mul, so we will get correct result.
NFP doesn't have integer divide instruction, this patch set uses reciprocal
algorithm (the basic one, reciprocal_div) to emulate it.
For each u32 divide, we would need 11 instructions to finish the operation.
7 (for multiplication) + 4 (various ALUs) = 11
Given NFP only supports multiplication no bigger than u32, we'd require
divisor and dividend no bigger than that as well.
Also eBPF doesn't support signed divide and has enforced this on C language
level by failing compilation. However LLVM assembler hasn't enforced this,
so it is possible for negative constant to leak in as a BPF_K operand
through assembly code, we reject such cases as well.
Meanwhile reciprocal_div.h only implemented the basic version of:
"Division by Invariant Integers Using Multiplication"
- Torbjörn Granlund and Peter L. Montgomery
This patch set further implements the optimized version (Figure 4.2 in the
paper) inside existing reciprocal_div.h. When the divider is even and the
calculated reciprocal magic number doesn't fit u32, we could reduce the
required ALU instructions from 4 to 2 or 1 for some cases.
The advanced version requires more complex calculation to get the
reciprocal multiplier and other control variables, but then could reduce
the required emulation operations. It makes sense to use it for JIT divide
code generation (for example eBPF JIT backends) for which we are willing to
trade performance of JITed code with that of host.
v2:
- add warning in l == 32 code path. (Song Liu/Jakub)
- jit separate insn sequence for l == 32. (Jakub/Edwin)
- should use unrestricted operand for mul.
- once place should use "1U << exp" instead of "1 << exp".
====================
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
As we are doing JIT, we would want to use the advanced version of the
reciprocal divide (reciprocal_value_adv) to trade performance with host.
We could reduce the required ALU instructions from 4 to 2 or 1.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP doesn't have integer divide instruction, this patch use reciprocal
algorithm (the basic one, reciprocal_div) to emulate it.
For each u32 divide, we would need 11 instructions to finish the operation.
7 (for multiplication) + 4 (various ALUs) = 11
Given NFP only supports multiplication no bigger than u32, we'd require
divisor and dividend no bigger than that as well.
Also eBPF doesn't support signed divide and has enforced this on C language
level by failing compilation. However LLVM assembler hasn't enforced this,
so it is possible for negative constant to leak in as a BPF_K operand
through assembly code, we reject such cases as well.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP supports u16 and u32 multiplication. Multiplication is done 8-bits per
step, therefore we need 2 steps for u16 and 4 steps for u32.
We also need one start instruction to initialize the sequence and one or
two instructions to fetch the result depending on either you need the high
halve of u32 multiplication.
For ALU64, if either operand is beyond u32's value range, we reject it. One
thing to note, if the source operand is BPF_K, then we need to check "imm"
field directly, and we'd reject it if it is negative. Because for ALU64,
"imm" (with s32 type) is expected to be sign extended to s64 which NFP mul
doesn't support. For ALU32, it is fine for "imm" be negative though,
because the result is 32-bits and here is no difference on the low halve
of result for signed/unsigned mul, so we will get correct result.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
NFP verifier hook is coping range information of the shift amount for
indirect shift operation so optimized shift sequences could be generated.
We want to use range info to do more things. For example, to decide whether
multiplication and divide are supported on the given range.
This patch simply let NFP verifier hook to copy range info for all operands
of all ALU operands.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The two fields are a copy of umin and umax info of bpf_insn->src_reg
generated by verifier.
Rename to make their meaning clear.
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
The new added "reciprocal_value_adv" implements the advanced version of the
algorithm described in Figure 4.2 of the paper except when
"divisor > (1U << 31)" whose ceil(log2(d)) result will be 32 which then
requires u128 divide on host. The exception case could be easily handled
before calling "reciprocal_value_adv".
The advanced version requires more complex calculation to get the
reciprocal multiplier and other control variables, but then could reduce
the required emulation operations.
It makes no sense to use this advanced version for host divide emulation,
those extra complexities for calculating multiplier etc could completely
waive our saving on emulation operations.
However, it makes sense to use it for JIT divide code generation (for
example eBPF JIT backends) for which we are willing to trade performance of
JITed code with that of host. As shown by the following pseudo code, the
required emulation operations could go down from 6 (the basic version) to 3
or 4.
To use the result of "reciprocal_value_adv", suppose we want to calculate
n/d, the C-style pseudo code will be the following, it could be easily
changed to real code generation for other JIT targets.
struct reciprocal_value_adv rvalue;
u8 pre_shift, exp;
// handle exception case.
if (d >= (1U << 31)) {
result = n >= d;
return;
}
rvalue = reciprocal_value_adv(d, 32)
exp = rvalue.exp;
if (rvalue.is_wide_m && !(d & 1)) {
// floor(log2(d & (2^32 -d)))
pre_shift = fls(d & -d) - 1;
rvalue = reciprocal_value_adv(d >> pre_shift, 32 - pre_shift);
} else {
pre_shift = 0;
}
// code generation starts.
if (imm == 1U << exp) {
result = n >> exp;
} else if (rvalue.is_wide_m) {
// pre_shift must be zero when reached here.
t = (n * rvalue.m) >> 32;
result = n - t;
result >>= 1;
result += t;
result >>= rvalue.sh - 1;
} else {
if (pre_shift)
result = n >> pre_shift;
result = ((u64)result * rvalue.m) >> 32;
result >>= rvalue.sh;
}
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit adds a bash completion to the bpftool cgroup tree
command.
Signed-off-by: Roman Gushchin <guro@fb.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Describe cgroup tree command in the corresponding bpftool man page.
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
This commit introduces a new bpftool command: cgroup tree.
The idea is to iterate over the whole cgroup tree and print
all attached programs.
I was debugging a bpf/systemd issue, and found, that there is
no simple way to listen all bpf programs attached to cgroups.
I did master something in bash, but after some time got tired of it,
and decided, that adding a dedicated bpftool command could be
a better idea.
So, here it is:
$ sudo ./bpftool cgroup tree
CgroupPath
ID AttachType AttachFlags Name
/sys/fs/cgroup/system.slice/systemd-machined.service
18 ingress
17 egress
/sys/fs/cgroup/system.slice/systemd-logind.service
20 ingress
19 egress
/sys/fs/cgroup/system.slice/systemd-udevd.service
16 ingress
15 egress
/sys/fs/cgroup/system.slice/systemd-journald.service
14 ingress
13 egress
Signed-off-by: Roman Gushchin <guro@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Edward Cree says:
====================
IP listification follow-ups
While working on IPv6 list processing, I found another bug in the IPv4
version. So this patch series has that fix, and the IPv6 version with
both fixes incorporated.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If we have an L3 master device, l3mdev_ip_rcv() will steal the skb, but
we were returning NET_RX_SUCCESS from ip_rcv_finish_core() which meant
that ip_list_rcv_finish() would keep it on the list. Instead let's
move the l3mdev_ip_rcv() call into the caller, so that our response to
a steal can be different in the single packet path (return
NET_RX_SUCCESS) and the list path (forget this packet and continue).
Fixes: 5fa12739a5 ("net: ipv4: listify ip_rcv_finish")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Warning level 2 was used: -Wimplicit-fallthrough=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'chip_ver' rather than 'chip' to check if the card
is T5.
Fixes: e8d452923a ("cxgb4: clean up init_one")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables adv and lpa are being assigned but are never used hence they
are redundant and can be removed. Also remove the unncessary mii_reads
too.
Cleans up clang warnings:
warning: variable 'lpa' set but not used [-Wunused-but-set-variable]
warning: variable 'adv' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Geert Uytterhoeven says:
====================
net: ethernet: Miscellaneous Kconfig and Makefile cleanups
This patch series contains a few Kconfig and Makefile cleanups w.r.t.
Ethernet vendors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Both SFC and SFC_FALCON depend on NET_VENDOR_SOLARFLARE, hence use the
latter to decide whether to descend into the sfc subdirectory.
Move the rule to descend into sfc/falcon to the sfc subdirectory.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor guard Kconfig symbols for Cadence and Packet Engines use a
"NET_" prefix, while all other vendor guards use a "NET_VENDOR_"
prefix. Hence make them consistent with the rest, and add the missing
trailing "S" for Packet Engines while at it.
As these options don't directly affect the kernel build, and default to
"y", this change has no impact on kernels built with existing
(def)configs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling NET_VENDOR_* Kconfig options does not directly affect the
kernel build. Hence NET_VENDOR_AURORA should default to yes, like other
NET_VENDOR_* options.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables consumer, cmd_desc, end_cnt and no_of_desc are being assigned
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'consumer' set but not used [-Wunused-but-set-variable]
warning: variable 'cmd_desc' set but not used [-Wunused-but-set-variable]
warning: variable 'end_cnt' set but not used [-Wunused-but-set-variable]
warning: variable 'no_of_desc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moshe Shemesh says:
====================
Add configuration parameters support
Add configuration parameters setting through devlink.
Each device registers supported configuration parameters table.
Each parameter can be either generic or driver specific.
The user can retrieve data on these parameters by "devlink param show"
command and can set new value to a parameter by "devlink param set"
command.
The parameters can be set in different configuration modes:
runtime - set while driver is running, no reset required.
driverinit - applied while driver initializes, requires restart
driver by devlink reload command.
permanent - written to device's non-volatile memory, hard reset required.
The patches at the end of the patchset introduce few params that are using
the introduced infrastructure on mlx4 and bnxt.
Command examples and output:
pci/0000:81:00.0:
name internal_error_reset type generic
values:
cmode runtime value true
cmode driverinit value true
name max_macs type generic
values:
cmode driverinit value 128
name enable_64b_cqe_eqe type driver-specific
values:
cmode driverinit value true
name enable_4k_uar type driver-specific
values:
cmode driverinit value false
pci/0000:81:00.0:
name internal_error_reset type generic
values:
cmode runtime value false
cmode driverinit value true
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial devlink parameters table for bnxt_en.
Table consists of a permanent generic parameter.
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enable_sriov - Enables Single-Root Input/Output Virtualization(SR-IOV)
characteristic of the device.
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx4_devlink_reload() to support devlink reload operation.
Add mlx4_devlink_param_load_driverinit_values() to load values which
were set using driverinit configuration mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create initial parameters table for mlx4.
The table consists of two generic parameters and two driver-specific
parameters.
Generic:
internal_err_reset - Enable reset device on internal errors. This
parameter can be configured on mlx4 either on runtime or during driver
initialization.
max_macs - Max number of MACs per ETH port. For mlx4 this parameter
value range is between 1 and 128. This parameter can be configured on
mlx4 only during driver initialization.
Driver specific:
enable_64b_cqe_eqe - Enable 64 byte CQEs/EQEs when the FW supports it.
This parameter can be configured on mlx4 only during driver
initialization.
enable_4k_uar - Enable using 4K UAR. This parameter can be configured on
mlx4 only during driver initialization.
Register the parameters table on mlx4_init_one() and unregister on
mlx4_remove_one().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 2 first generic parameters to devlink configuration parameters set:
internal_err_reset - When set enables reset device on internal errors.
max_macs - max number of MACs per ETH port.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add devlink_param_notify() function to support devlink param notifications.
Add notification call to devlink param set, register and unregister
functions.
Add devlink_param_value_changed() function to enable the driver notify
devlink on value change. Driver should use this function after value was
changed on any configuration mode part to driverinit.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"driverinit" configuration mode value is held by devlink to enable
the driver query the value after reload. Two additional functions
added to help the driver get/set the value from/to devlink:
devlink_param_driverinit_value_set() and
devlink_param_driverinit_value_get().
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add param set command to set value for a parameter.
Value can be set to any of the supported configuration modes.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add param get command which gets data per parameter.
Option to dump the parameters data per device.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define configuration parameters data structure.
Add functions to register and unregister the driver supported
configuration parameters table.
For each parameter registered, the driver should fill all the parameter's
fields. In case the only supported configuration mode is "driverinit"
the parameter's get()/set() functions are not required and should be set
to NULL, for any other configuration mode, these functions are required
and should be set by the driver.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable channel is being assigned but is never used hence it is
redundant and can be removed.
Cleans up two clang warnings:
warning: variable 'channel' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables my_epid and max_epid are currently assigned and not being
used - however, I suspect they were intended to be used in the for-loops
to reduce the dereferencing of hw. Replace hw->my_epid and hw->max_epid
with these variables.
Cleans up clang warnings:
warning: variable 'my_epid' set but not used [-Wunused-but-set-variable]
variable 'max_epid' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer skb is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'skb' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer ndev is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'ndev' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:525:5: warning:
symbol 'hw_atl_utils_mpi_set_speed' was not declared. Should it be static?
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:536:5: warning:
symbol 'hw_atl_utils_mpi_set_state' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/dsa/vitesse-vsc73xx.c:1054:6: warning:
symbol 'vsc73xx_get_strings' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1113:5: warning:
symbol 'vsc73xx_get_sset_count' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1122:6: warning:
symbol 'vsc73xx_get_ethtool_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 07d78363dc ("net: Convert NAPI gro list into a small hash
table.")' there is 8 hash buckets, which allows more flows to be held for
merging. but MAX_GRO_SKBS, the total held skb for merging, is 8 skb still,
limit the hash table performance.
keep MAX_GRO_SKBS as 8 skb, but limit each hash list length to 8 skb, not
the total 8 skb
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When runtime-suspending we configure WoL w/o touching saved_wolopts.
If saved_wolopts == 0 we would power down the PHY in this case what's
wrong. Therefore we have to check the actual chip WoL settings here.
Fixes: 433f9d0ddc ("r8169: improve saved_wolopts handling")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
