raid_io_hints() was retrieving the number of data stripes used for the
calculation of io_opt from struct r5conf, which is not defined for raid0
mappings.
Base the calculation on the in-core raid_set structure instead.
Also, adjust to use to_bytes() for the sector -> bytes conversion
throughout.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use 'unsigned int' where appropriate.
Return negative errors.
Correct an indentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add "delta_disks" constructor argument support to raid1 to allow for
consistent userspace disk addition/removal handling.
Fix raid_status() to report all raid disks with status and table output
on disk adding reshapes, not just the ones listed on the mddev; optimize
its rebuild and writemostly output.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Enhance rs_reshape_requested() check function to be more transparent and
fix its raid10 check.
Streamline the constructor by factoring out reshaping preparation into
fucntion rs_prepare_reshape().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Resizing a RAID set during recovery can be allowed, because the MD
resynchronization thread will either stop any ongoing recovery in case
of shrinking below the current recovery position or carry on recovery
to the new size if the set is growing.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add function rs_setup_recovery() to allow for defined setup of RAID set
recovery in the constructor.
Will be called with dev_sectors={0, rdev->sectors, MaxSectors} to
recover a new or enforced sync, grown or not to be synhronized RAID set
respectively.
Prevents recovery on raid0, which doesn't support it.
Enforces recovery on raid6 to ensure properly defined Syndromes
mandatory for that MD personality are being created.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A newly introduced function has 'const int' as the return type,
but as "make W=1" reports, that has no meaning:
drivers/md/dm-raid.c:510:18: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
This changes the return type to plain 'int'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 33e53f0685 ("dm raid: introduce extended superblock and new raid types to support takeover/reshaping")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Superblock updates where bogus causing some takovers/reshapes to fail.
Introduce new runtime flag (RT_FLAG_KEEP_RS_FROZEN) to keep a raid set
frozen when a layout change was requested. Userpace will immediately
reload the table w/o the flags requesting such change once they made it
to the superblocks and any change of recovery/reshape offsets has to be
avoided until after read.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add bool functions rs_is_recovering and rs_is_reshaping()
to test for ongoing recovery/reshaping respectively in order
to reject respective requests on ongoing ones.
Remove ctr array size check, because ti->len and array
sectors will differ during disk addition/removal reshape.
Use __is_raid10_near() rather than type string compare.
Introduce rs_check_reshape() and rs_start_reshape(),
use the former in the ctr to reject bogus rehsape requests
and the latter in preresume to actually start a reshape.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add rs_is_reshapable(), rs_data_stripes(), rs_reshape_requested(),
rs_set_dev_and_array_sectors() and rs_adjust_data_offsets()
Remove superfluous check for reshape message
Correct runtime bit definitions to be incremental
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is more intuitive to manage each raid level's features in terms of
what is supported rather than what isn't supported.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Renamed functions and variables with leading single underscore to have a
double underscore. Renamed some functions to have better names. Folded
functions that were split out without reason.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Also update module description to "raid0/1/10/4/5/6 target"
Reported by Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
No idea what Heinz was doing with the versioning but upstream commit
4c9971ca6a ("dm raid: make sure no feature flags are set in metadata")
bumped to 1.8.0 already.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There ti_error_* wrappers added very little. No other DM target has
ever gone to such lengths to wrap setting ti->error.
Also fixes some NULL derefences via rs->ti->error.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The target's status interface has to provide the new 'data_offset' value
to allow userspace to retrieve the kernels offset to the data on each
raid device of a raid set. This is the base for out-of-place reshaping
required to not write over any data during reshaping (e.g. change
raid6_zr -> raid6_nc):
- add rs_set_cur() to be able to start up existing array in case of no
takeover; use in ctr on takeover check
- enhance raid_status()
- add supporting functions to get resync/reshape progress and raid
device status chars
- fixup rebuild table line output race, which does miss to emit
'rebuild N' on fully synced/rebuild devices, because it is relying on
the transient 'In_sync' raid device flag
- add new status line output for 'data_offset', which'll later be used
for out-of-place reshaping
- fixup takeover not working for all levels
- fixup raid0 message interface oops caused by missing checks
for the md threads, which don't exist in case of raid0
- remove ALL_FREEZE_FLAGS not needed for takeover
- adjust comments
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add raid level takeover support allowing arbitrary takeovers between
raid levels supported by md personalities (i.e. raid0, raid1/10 and
raid4/5/6):
- add rs_config_{backup|restore} function to allow for temporary
storing ctr requested layout changes and restore them for takeover
conersion decision after the superblocks got loaded and analyzed
- add members to store layout to 'struct raid_set' (not mandatory
for takeover but needed for reshape in later patch)
- add rebuild_disks bitfield to 'struct raid_set' and set bits in ctr
to use in setting up takeover (base to address a 'rebuild' related
raid_status() table line bug and needed as well for reshape in future
patch)
- add runtime flags and respective manipulation functions to be able to
control e.g. wrting of superlocks to the preresume function on
takeover and (later) reshape
- add functions to detect takeover, check it's valid (mandatory here to
avoid failing on md_run()), setup for it and use in the ctr; those
will be likely moved out once reshaping gets added to simplify the
ctr
- start raid set readonly in ctr and switch to readwrite, optionally
updating superblocks, in preresume in order to allow suspend to
quiesce any active table before (which involves superblock updates);
this ensures the proper sequence of writing the current and any new
takeover(/reshape) metadata
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add transferring the new takeover/reshape related superblock
members introduced to the super_sync() function:
- add/move supporting functions
- add failed devices bitfield transfer functions to retrieve the
bitfield from superblock format or update it in the superblock
- add code to transfer all new members
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Support the follwoing arguments in the ctr parameter parser:
- add 'delta_disks', 'data_offset' taking int and sector respectively
- 'raid10_use_near_sets' bool argument to optionally select
near sets with supporting raid10 mappings
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add new members to the dm-raid superblock and new raid types to support
takeover/reshape.
Add all necessary members needed to support takeover and reshape in one
go -- aiming to limit the amount of changes to the superblock layout.
This is a larger patch due to the new superblock members, their related
flags, validation of both and involved API additions/changes:
- add additional members to keep track of:
- state about forward/backward reshaping
- reshape position
- new level, layout, stripe size and delta disks
- data offset to current and new data for out-of-place reshapes
- failed devices bitfield extensions to keep track of max raid devices
- adjust super_validate() to cope with new superblock members
- adjust super_init_validation() to cope with new superblock members
- add definitions for ctr flags supporting delta disks etc.
- add new raid types (raid6_n_6 etc.)
- add new raid10 supporting function API (_is_raid10_*())
- adjust to changed raid10 supporting function API
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Make use if raid type rt_is_*() bool functions for simplification and
consistency reasons.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
- add _test_flags() function
- use it to simplify rs_check_for_invalid_flags()
- use _test_flag() throughout
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Reject invalid flag combinations to avoid potential data corruption or
failing raid set construction:
- add definitions for constructor flag combinations and invalid flags
per level
- add bool test functions for the various raid types
(also will be used by future reshaping enhancements)
- introduce rs_check_for_invalid_flags() and _invalid_flags()
to perform the validity checks
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
