This patch moves the tpm_tis_reenable_interrupts function out of the
CONFIG_PNP-surrounded #define block. This solves a compilation error in
case CONFIG_PNP is not defined.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Morris <jmorris@namei.org>
The is_itpm() function is only accessed from a block surrounded by
#ifdef CONFIG_PNP. Therefore, also surround it with #ifdef CONFIG_PNP
and remove the #else branch causing the warning.
http://lxr.linux.no/#linux+v2.6.39/drivers/char/tpm/tpm_tis.c#L622
v2:
- fixes a previous typo
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Morris <jmorris@namei.org>
This patch introduces a function for automatic probing for the Intel iTPM
STS_DATA_EXPECT flaw.
The patch splits the current tpm_tis_send function into 2 parts where the 1st
part is now called tpm_tis_send_data() and merely sends the data to the TPM.
This function is then used for probing. The new tpm_tis_send function now
first calls tpm_tis_send_data and if that succeeds has the TPM process the
command and waits until the response is there.
The probing for the Intel iTPM is only invoked if the user has not passed
itpm=1 as parameter for the module *or* if such a TPM was detected via ACPI.
Previously it was necessary to pass itpm=1 when also passing force=1 to the
module when doing a 'modprobe'. This function is more general than the ACPI
test function and the function relying on ACPI could probably be removed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes several aspects of the probing for interrupts.
This patch reads the TPM's timeouts before probing for the interrupts. The
tpm_get_timeouts() function is invoked in polling mode and gets the proper
timeouts from the TPM so that we don't need to fall back to 2 minutes timeouts
for short duration commands while the interrupt probing is happening.
This patch introduces a variable probed_irq into the vendor structure that gets
the irq number if an interrupt is received while the the tpm_gen_interrupt()
function is run in polling mode during interrupt probing. Previously some
parts of tpm_gen_interrupt() were run in polling mode, then the irq variable
was set in the interrupt handler when an interrupt was received and execution
of tpm_gen_interrupt() ended up switching over to interrupt mode.
tpm_gen_interrupt() execution ended up on an event queue where it eventually
timed out since the probing handler doesn't wake any queues.
Before calling into free_irq() clear all interrupt flags that may have
been set by the TPM. The reason is that free_irq() will call into the probing
interrupt handler and may otherwise fool us into thinking that a real interrupt
happened (because we see the flags as being set) while the TPM's interrupt line
is not even connected to anything on the motherboard. This solves a problem
on one machine I did testing on (Thinkpad T60).
If a TPM claims to use a specifc interrupt, the probing is done as well
to verify that the interrupt is actually working. If a TPM indicates
that it does not use a specific interrupt (returns '0'), probe all interrupts
from 3 to 15.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch delays the (ACPI S3) suspend while the TPM is busy processing a
command and the TPM TIS driver is run in interrupt mode. This is the same
behavior as we already have it for the TPM TIS driver in polling mode.
Reasoning: Some of the TPM's commands advance the internal state of the TPM.
An example would be the extending of one of its PCR registers. Upper layers,
such as IMA or TSS (TrouSerS), would certainly want to be sure that the
command succeeded rather than getting an error code (-62 = -ETIME) that may
not give a conclusive answer as for what reason the command failed. Reissuing
such a command would put the TPM into the wrong state, so waiting for it to
finish is really the only option.
The downside is that some commands (key creation) can take a long time and
actually prevent the machine from entering S3 at all before the 20 second
timeout of the power management subsystem arrives.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch makes sure that if the TPM TIS interface is run in interrupt mode
(rather than polling mode) that all interrupts are enabled in the TPM's
interrupt enable register after a resume from ACPI S3 suspend. The registers
may either have been cleared by the TPM loosing its state during device sleep
or by the BIOS leaving the TPM in polling mode (after sending a command to
the TPM for starting it up again)
You may want to check if your TPM runs with interrupts by doing
cat /proc/interrupts | grep -i tpm
and see whether there is an entry or otherwise for it to use interrupts:
modprobe tpm_tis interrupts=1 [add 'itpm=1' for Intel TPM ]
v2:
- the patch was adapted to work with the pnp and platform driver
implementations in tpm_tis.c
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes the TPM's pubek sysfs entry that is accessible as long
as the TPM doesn't have an owner. It was necessary to shift the access to the
data by -10 -- the first byte immediately follows the 10 byte header. The
line
data = tpm_cmd.params.readpubek_out_buffer;
sets it at the offset '10' in the packet, so we can read the data array
starting at offset '0'.
Before:
Algorithm: 00 0C 00 00
Encscheme: 08 00
Sigscheme: 00 00
Parameters: 00 00 00 00 01 00 AC E2 5E 3C A0 78
Modulus length: -563306801
Modulus:
28 21 08 0F 82 CD F2 B1 E7 49 F7 74 70 BE 59 8C
43 78 B1 24 EA 52 E2 FE 52 5C 3A 12 3B DC 61 71
[...]
After:
Algorithm: 00 00 00 01
Encscheme: 00 03
Sigscheme: 00 01
Parameters: 00 00 08 00 00 00 00 02 00 00 00 00
Modulus length: 256
Modulus:
AC E2 5E 3C A0 78 DE 6C 9E CF 28 21 08 0F 82 CD
F2 B1 E7 49 F7 74 70 BE 59 8C 43 78 B1 24 EA 52
[...]
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's interface timeouts in a 'timeouts' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Adjust the interface timeouts if they are found to be too small, i.e., if
they are returned in milliseconds rather than microseconds as we heared
from Infineon that some (old) Infineon TPMs do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
The TPM driver currently discards the interface timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 4 interface timeout indicators of type u32.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's command timeouts in a 'durations' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Adjust the durations if they are found to be too small, i.e., if they are
returned in milliseconds rather than microseconds as some Infineon TPMs are
reported to do.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
The TPM driver currently discards the durations values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
v4:
- sysfs entry 'durations' is now a patch of its own
- the work-around for TPMs reporting durations in milliseconds is now in a
patch of its own
v3:
- sysfs entry now called 'durations' to resemble TPM-speak (previously
was called 'timeouts')
v2:
- adjusting all timeouts for TPM devices reporting timeouts in msec rather
than usec
- also displaying in sysfs whether the timeouts are 'original' or 'adjusted'
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes information leakage to the userspace by initializing
the data buffer to zero.
Reported-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Peter Huewe <huewe.external@infineon.com>
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
[ Also removed the silly "* sizeof(u8)". If that isn't 1, we have way
deeper problems than a simple multiplication can fix. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit c4ff4b829e.
Ted Ts'o reports:
"TPM is working for me so I can log into employer's network in 2.6.37.
It broke when I tried 2.6.38-rc6, with the following relevant lines
from my dmesg:
[ 11.081627] tpm_tis 00:0b: 1.2 TPM (device-id 0x0, rev-id 78)
[ 25.734114] tpm_tis 00:0b: Operation Timed out
[ 78.040949] tpm_tis 00:0b: Operation Timed out
This caused me to get suspicious, especially since the _other_ TPM
commit in 2.6.38 had already been reverted, so I tried reverting
commit c4ff4b829e: "TPM: Long default timeout fix". With this commit
reverted, my TPM on my Lenovo T410 is once again working."
Requested-and-tested-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 9b29050f8f.
It has caused hibernate regressions, for example Juri Sladby's report:
"I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
[10974.074587] Suspending console(s) (use no_console_suspend to debug)
[10974.103073] tpm_tis 00:0c: Operation Timed out
[10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
[10974.103095] PM: Device 00:0c failed to freeze: error -62"
and Rafael points out that some of the new conditionals in that commit
seem to make no sense. This commit needs more work and testing, let's
revert it for now.
Reported-by: Norbert Preining <preining@logic.at>
Reported-and-requested-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current TPM TIS driver in git discards the timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
I am also adding a sysfs entry 'timeouts' showing the timeouts that are
being used.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
commit 3f0d3d016d adds a check for
PNP device id to the common tpm_tis_init() function, which in some
cases (force=1) will be called without the device being a member of
a pnp_dev. Oopsing and panics ensue.
Move the test up to before the call to tpm_tis_init(), since it
just modifies a global variable anyway.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
If duration variable value is 0 at this point, it's because
chip->vendor.duration wasn't filled by tpm_get_timeouts() yet.
This patch sets then the lowest timeout just to give enough
time for tpm_get_timeouts() to further succeed.
This fix avoids long boot times in case another entity attempts
to send commands to the TPM when the TPM isn't accessible.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
Conflicts:
security/smack/smack_lsm.c
Verified and added fix by Stephen Rothwell <sfr@canb.auug.org.au>
Ok'd by Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Some Lenovos have TPMs that require a quirk to function correctly. This can
be autodetected by checking whether the device has a _HID of INTC0102. This
is an invalid PNPid, and as such is discarded by the pnp layer - however
it's still present in the ACPI code, so we can pull it out that way. This
means that the quirk won't be automatically applied on non-ACPI systems,
but without ACPI we don't have any way to identify the chip anyway so I
don't think that's a great concern.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Tested-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Andy Isaacson <adi@hexapodia.org>
Signed-off-by: James Morris <jmorris@namei.org>
Add internal kernel tpm_send() command used to seal/unseal keys.
Changelog:
- replaced module_put in tpm_send() with new tpm_chip_put() wrapper
(suggested by David Howells)
- Make tpm_send() cmd argument a 'void *' (suggested by David Howells)
Signed-off-by: David Safford <safford@watson.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
For readability, define a tpm_chip_put() wrapper to call module_put().
Replace existing module_put() calls with the wrapper.
(Change based on trusted/encrypted patchset review by David Howells.)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Safford <safford@watson.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
Fix the following warning:
drivers/char/tpm/tpm.c:1085: warning: `tpm_suspend_setup' defined but not used
and make the workaround operable in case when TPM is compiled as a module.
As a side-effect the option will be called tpm.suspend_pcr.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: David Safford <safford@watson.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
The patch below updates broken web addresses in the kernel
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Finn Thain <fthain@telegraphics.com.au>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Dimitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Ben Pfaff <blp@cs.stanford.edu>
Acked-by: Hans J. Koch <hjk@linutronix.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Fix subsequent suspends by issuing tpm_continue_selftest during resume.
Otherwise, the tpm chip seems to be not fully initialized and will reject
the save state command during suspend, thus preventing the whole system
to suspend.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16256
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: David Safford <safford@watson.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds a missing element of the ReadPubEK command output,
that prevents future overflow of this buffer when copying the
TPM output result into it.
Prevents a kernel panic in case the user tries to read the
pubek from sysfs.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch pushes the ACPI dependency into the device driver code
itself. Now, even without ACPI/PNP enabled, the device can be registered
using the TIS specified memory space. This will however result in the
lack of access to the BIOS event log, being the only implication of such
ACPI removal.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This reverts commit b89e66e1e3.
> > When CONFIG_PM is not set:
> >
> > drivers/built-in.o: In function `acpi_init':
> > bus.c:(.init.text+0x2d84): undefined reference to `pm_flags'
> > bus.c:(.init.text+0x2d91): undefined reference to `pm_flags'
>
> CONFIG_ACPI depends on CONFIG_PM,
> so acpi/bus.c should not be compiled for CONFIG_PM=n
>
> Hmm, is is somebody doing something strange, like "select ACPI"
> without guaranteeing that all of ACPI's dependencies are satisfied?
Signed-off-by: James Morris <jmorris@namei.org>
This patch pushes the ACPI dependency into the device driver code
itself. Now, even without ACPI/PNP enabled, the device can be registered
using the TIS specified memory space. This will however result in the
lack of access to the bios event log, being the only implication of such
ACPI removal.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Add a workaround for TPM's which fail to flush last written
PCR values in a TPM_SaveState, in preparation for suspend.
Signed-off-by: David Safford <safford@watson.ibm.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
When suspending, tpm_infineon calls the generic suspend function of the
TPM framework. However, the TPM framework does not return and the system
hangs upon suspend. When sending the necessary command "TPM_SaveState"
directly within the driver, suspending and resuming works fine.
Signed-off-by: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: <stable@kernel.org> [2.6.32.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tpm_tis driver already has a list of supported pnp_device_ids.
This patch simply exports that list as a MODULE_DEVICE_TABLE() so that
the module autoloader will discover and load the module at boottime.
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
Some newer Lenovo models are shipped with a TPM that doesn't seem to set the TPM_STS_DATA_EXPECT status bit
when sending it a burst of data, so the code understands it as a failure and doesn't proceed sending the chip
the intended data. In this patch we bypass this bit check in case the itpm module parameter was set.
This patch is based on Andy Isaacson's one:
http://marc.info/?l=linux-kernel&m=124650185023495&w=2
It was heavily discussed how should we deal with identifying the chip in kernel space, but the required
patch to do so was NACK'd:
http://marc.info/?l=linux-kernel&m=124650186423711&w=2
This way we let the user choose using this workaround or not based on his
observations on this code behavior when trying to use the TPM.
Fixed a checkpatch issue present on the previous patch, thanks to Daniel Walker.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Eric Paris <eparis@redhat.com>
Tested-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Signed-off-by: James Morris <jmorris@namei.org>
The previously sent patch:
http://marc.info/?l=tpmdd-devel&m=125208945007834&w=2
Had its first hunk cropped when merged, submitting only this first hunk
again.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Cc: Marcel Selhorst <m.selhorst@sirrix.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Mimi Zohar <zohar@us.ibm.com>
Tested-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
The TPM Working Group requested this communication buffer increase given that a
particular TPM vendor can support a TPM_SHA1Start command input bigger than the
current size.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
SELinux: do not destroy the avc_cache_nodep
KEYS: Have the garbage collector set its timer for live expired keys
tpm-fixup-pcrs-sysfs-file-update
creds_are_invalid() needs to be exported for use by modules:
include/linux/cred.h: fix build
Fix trivial BUILD_BUG_ON-induced conflicts in drivers/char/tpm/tpm.c
gcc permitting variable length arrays makes the current construct used for
BUILD_BUG_ON() useless, as that doesn't produce any diagnostic if the
controlling expression isn't really constant. Instead, this patch makes
it so that a bit field gets used here. Consequently, those uses where the
condition isn't really constant now also need fixing.
Note that in the gfp.h, kmemcheck.h, and virtio_config.h cases
MAYBE_BUILD_BUG_ON() really just serves documentation purposes - even if
the expression is compile time constant (__builtin_constant_p() yields
true), the array is still deemed of variable length by gcc, and hence the
whole expression doesn't have the intended effect.
[akpm@linux-foundation.org: make arch/sparc/include/asm/vio.h compile]
[akpm@linux-foundation.org: more nonsensical assertions in tpm.c..]
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: Mimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.
This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When probing the device in tpm_tis_init the call request_locality
uses timeout_a, which wasn't being initalized until after
request_locality. This results in request_locality falsely timing
out if the chip is still starting. Move the initialization to before
request_locality.
This probably only matters for embedded cases (ie mine), a BIOS likely
gets the TPM into a state where this code path isn't necessary.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
