MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.
Add pin control driver to configure these parameters through
pin control APIs.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl and gpio control support to Oxford Semiconductor OXNAS SoC Family.
This version supports the ARM926EJ-S based OX810SE SoC with 34 IO pins.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_MTK is more suitable than CONFIG_ARCH_MEDIATEK
to guard the drivers/pinctrl/mediatek/ directory.
(I renamed CONFIG_PINCTRL_MTK_COMMON to CONFIG_PINCTRL_MTK.)
This allows COMPILE_TEST to descend into drivers/pinctrl/mediatek
without CONFIG_ARCH_MEDIATEK define.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While selecting the driver for compile testing seemed possible,
the driver was not compiled because the driver directory was only
added if ARCH_STM32 was selected.
This patch now makes the pinctrl Makefile to add stm32 directory if
PINCTRL_STM32 is selected.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the pin controller present on the Microchip PIC32
including the specific variant PIC32MZDA. This driver provides pinmux
and pinconfig operations as well as GPIO and IRQ chips for the GPIO
banks.
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra has several pinctrl drivers. Now it is reasonable enough to
move them into drivers/pinctrl/tegra/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_SUNXI is more suitable than CONFIG_ARCH_SUNXI
to guard the drivers/pinctrl/sunxi/ directory.
(I renamed CONFIG_PINCTRL_SUNXI_COMMON to CONFIG_PINCTRL_SUNXI.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_PXA is more suitable than CONFIG_ARCH_PXA
to guard the drivers/pinctrl/pxa/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds pinctrl and GPIO support to STMicroelectronic's STM32
family of MCUs.
While it only supports STM32F429 for now, it has been designed to enable
support of other MCUs of the family (e.g. STM32F746).
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the pxa architecture, at least for pxa27x, supports pin control,
activate it in the pinctrl tree.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_SPEAR is more suitable than CONFIG_PLAT_SPEAR
to guard the drivers/pinctrl/spear/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_MVEBU is more suitable than CONFIG_PLAT_ORION
to guard the drivers/pinctrl/mvebu/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_BERLIN is more suitable than CONFIG_ARCH_BERLIN
to guard the drivers/pinctrl/berlin/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
CONFIG_PINCTRL_UNIPHIER is more suitable than CONFIG_ARCH_UNIPHIER
to guard the drivers/pinctrl/uniphier directory.
The current CONFIG_PINCTRL_UNIPHIER_CORE is a bit long
(it would break the indentation in drivers/pinctrl/Makefile),
so rename it into CONFIG_PINCTRL_UNIPHIER.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl and gpio driver to the CX92755 SoC "General
Purpose Pin Mapping" hardware block. The CX92755 is one SoC
from the Conexant Digicolor series. Pin mapping hardware supports
configuring pins as either GPIO, or up to 3 other "client select"
functions. This driver adds support for pin muxing using the
generic device tree binding, and a basic gpiolib driver for
the GPIO functionality.
This driver does not currently support GPIO interrupts, and
pad configuration.
v2:
* Address review comments for Linus Walleij:
- Add a pointer to pinctrl_desc in struct dc_pinmap
- Drop the now redundant pinctrl_pin_desc field
- Adapt dc_get_group_{name,pins} to these changes, and
add a comment explaining the 1-to-1 pin-groups relation
* Staticise dc_pmxops
* Protect the GP_CLIENTSEL clct parameter with parenthesis
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kbuild should descend into drivers/pinctrl/ only when CONFIG_PINCTRL
is enabled because everything under that directory depends on
CONFIG_PINCTRL.
We can avoid the conditional, ifeq ($(CONFIG_OF),y) ... endif.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The core support for the pinctrl drivers for all the UniPhier SoCs.
Changes in v2:
- drop vogus THIS_MODULE because this file is always built-in
- drop vogus "include <linux/module.h> because this file is
always built-in
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a driver for the pin controller present on the IMG Pistachio SoC.
This driver provides pinmux and pinconfig operations as well as GPIO
and IRQ chips for the GPIO banks.
Changes from v4:
- Switched to using gpiochip_add_pin_range().
- Fixed up Kconfig entry.
Changes from v3:
- Addressed review comments from Ezequiel.
Changes from v2:
- Removed module stuff which would be compiled out.
Changes from v1:
- Addressed review comments from Linus.
- Changed compatible string to "img,pistachio-system-pinctrl".
- Look for GPIO sub-nodes by name.
- A couple of bug fixes.
Signed-off-by: Damien Horsley <Damien.Horsley@imgtec.com>
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.
Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
KERNCZ GPIO is a new IP from AMD. it can be implemented in both x86 and ARM.
Current driver patch only support GPIO in x86.
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
[Moved back to <linux/gpio.h> header]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mediatek SoCs have GPIO controller that handle both the muxing and GPIOs.
The GPIO controller have pinmux, pull enable, pull select, direction and output high/low control.
This driver include common driver and mt8135 part.
The common driver include the pinctrl driver and GPIO driver.
The mt8135 part contain its special device data.
Signed-off-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tegra210's pinmux supports a different set of pins/options than earlier
SoCs, so requires its own driver (well, table of pin-specific data).
Cc: devicetree@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a driver for the pinmux and GPIO controller available in
Amlogic Meson SoCs. It currently supports only Meson8, however the
common code should be generic enough to work also for other SoCs after
having defined the proper set of functions and groups.
GPIO interrupts are not supported at the moment due to lack of
documentation.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pin-control driver for Zynq.
Changes since v2:
- driver-specific DT properties are passed to the core in two arrays,
one for the actual DT parsing one for the debugfs representation.
Issue a compiler warning when the number of entries is not the same
for both arrays.
Changes since v1:
- fix EMIO_SD1_CD pin name
- add USB to pinmux options
changes since RFCv2:
- let Zynq select PINCTRL_ZYNQ. Boot hangs when pinctrl information is
present in DT but no driver available.
- add #defines to get rid of magical constants
- add commas at end of initializers
- separate changes in mach-zynq in separate patch
- add driver specific io-standard DT property
- refactored pinconf set function to not require arguments for
argument-less properties
- squash other patches in
- support for IO-standard property
- support for low-power mode property
- migration to pinconf_generic_dt_node_to_map_all()
- use newly created infrastructure to add pass driver-specific DT
params to pinconf-generic
changes since RFC:
- use syscon/regmap to access registers in SLCR space
- rebase to 3.18: rename enable -> set_mux
- add kernel-doc
- support pinconf
- supported attributes
- pin-bias: pull up, tristate, disable
- slew-rate: 0 == slow, 1 == fast; generic pinconf does not display
argument
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When drivers are compiled in subdirectories the -DDEBUG flag need
to be passed in the individual Makefiles.
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Suggested-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We are going to have more pinctrl drivers for Intel hardware so separate
all our pin controller drivers to own directory.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves all the Freescale-related drivers (i.MX and MXS) to
its own subdirectory to clear the view.
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Anson Huang <b20788@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Denis Carikli <denis@eukrea.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is currently a kludge to get the Makefile to move down
to sh-pfc:s drivers: the arch definitions are used twice to
get it done. However we can very well use the Kconfig symbol
for the SH PFC pin control feature itself: it doesn't matter
that it comes from a lower leaf in the Kconfig hierarchy which
is completely orthogonal.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Samsung Exynos7 is a ARM64bit processor. Which does not select
the CONFIG_PLAT_SAMSUNG symbol. CONFIG_PINCTRL_SAMSUNG is being
selected for both PLAT_SAMSUNG and ARCH_EXYNOS7 symbols.
This patch modifes the pinctrl/Makefile to use
CONFIG_PINCTRL_SAMSUNG symbol to compile the pinctrl/samsung/*.c
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Cc: Tomasz Figa <t.figa@samsung.com>
Cc: linus.walleij@linaro.org
Cc: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new platforms,
but there's also a bit of cleanup and code removal for things that
are moved from platform code to DT contents (some OMAP clock code in
particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no particular
order:
* Rockchip RK3288 SoC support, including DTS for a dev board that they
have seeded with some community developers.
* Better support for Hardkernel Exynos4-based ODROID boards.
* CCF conversions (and dtsi contents) for several Renesas platforms.
* Gumstix Pepper (TI AM335x) board support
* TI eval board support for AM437x
* Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an Ippo
tablet with the chipset.
* Allwinner A31 Hummingbird board support, not to be confused with the
SolidRun i.MX-based Hummingboard.
* Tegra30 Apalis board support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxlY
-----END PGP SIGNATURE-----
Merge tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device-tree changes from Olof Johansson:
"Unlike the board branch, this keeps having large sets of changes for
every release, but that's quite expected and is so far working well.
Most of this is plumbing for various device bindings and new
platforms, but there's also a bit of cleanup and code removal for
things that are moved from platform code to DT contents (some OMAP
clock code in particular).
There's also a pinctrl driver for tegra here (appropriately acked),
that's introduced this way to make it more bisectable.
I'm happy to say that there were no conflicts at all with this branch
this release, which means that changes are flowing through our tree as
expected instead of merged through driver maintainers (or at least not
done with conflicts).
There are several new boards added, and a couple of SoCs. In no
particular order:
- Rockchip RK3288 SoC support, including DTS for a dev board that
they have seeded with some community developers.
- Better support for Hardkernel Exynos4-based ODROID boards.
- CCF conversions (and dtsi contents) for several Renesas platforms.
- Gumstix Pepper (TI AM335x) board support
- TI eval board support for AM437x
- Allwinner A23 SoC, very similar to existing ones which mostly has
resulted in DT changes for support. Also includes support for an
Ippo tablet with the chipset.
- Allwinner A31 Hummingbird board support, not to be confused with
the SolidRun i.MX-based Hummingboard.
- Tegra30 Apalis board support"
* tag 'dt-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (334 commits)
ARM: dts: Enable USB host0 (EHCI) on rk3288-evb
ARM: dts: add rk3288 ehci usb devices
ARM: dts: Turn on USB host vbus on rk3288-evb
ARM: tegra: apalis t30: fix device tree compatible node
ARM: tegra: paz00: Fix some indentation inconsistencies
ARM: zynq: DT: Clarify Xilinx Zynq platform
ARM: dts: rockchip: add watchdog node
ARM: dts: rockchip: remove pinctrl setting from radxarock uart2
ARM: dts: Add missing pinctrl for uart0/1 for exynos3250
ARM: dts: Remove duplicate 'interrput-parent' property for exynos3250
ARM: dts: Add TMU dt node to monitor the temperature for exynos3250
ARM: dts: Specify MAX77686 pmic interrupt for exynos5250-smdk5250
ARM: dts: cypress,cyapa trackpad is exynos5250-Snow only
ARM: dts: max77686 is exynos5250-snow only
ARM: zynq: DT: Remove DMA from board DTs
ARM: zynq: DT: Add CAN node
ARM: EXYNOS: Add exynos5260 PMU compatible string to DT match table
ARM: dts: Add PMU DT node for exynos5260 SoC
ARM: EXYNOS: Add support for Exynos5410 PMU
ARM: dts: Add PMU to exynos5410
...
We have a bunch of Nomadik family pin control drivers, so let's
move them into their own subdirectory.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The XUSB pad controller found on NVIDIA Tegra SoCs provides several pads
that lanes can be assigned to in order to support a variety of interface
options: USB 2.0, USB 3.0, PCIe and SATA.
In addition to the pin controller used to assign lanes to pads two PHYs
are exposed to allow the bricks for PCIe and SATA to be powered up and
down by PCIe and SATA drivers.
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Group all pin control drivers of Samsung platform together in
a sub-directory for easy maintenance.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have four Qualcomm-related pin control drivers, and now there
are drivers coming in for the PMICs on these systems, so let's
create a qcom subdirectory to hold all the Qualcomm stuff.
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Acked-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Marvell Berlin boards have a group based pinmuxing mechanism. This
adds the core driver support. We actually do not need any information
about the pins here and only have the definition of the groups.
Let's take the example of the uart0 pinmuxing on the BG2Q. Balls BK4 and
BH6 are muxed to respectively UART0 RX and TX if the group GSM12 is set
to mode 0:
Group Modes Offset Base Offset LSB Bit Width
GSM12 3 sm_base 0x40 0x10 0x2
Ball Group Mode 0 Mode 1 Mode 2
BK4 GSM12 UART0_RX IrDA0_RX GPIO9
BH6 GSM12 UART0_TX IrDA0_TX GPIO10
So in order to configure BK4 -> UART0_TX and BH6 -> UART0_RX, we need
to set (sm_base + 0x40 + 0x10) &= ff3fffff.
As pin control registers are part of either chip control or system
control registers, that deal with a bunch of other functions we rely
on a regmap instead of exclusively remapping any resources.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm IPQ8064 platform.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm APQ8064 platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To be consistent with other Broadcom drivers, the Broadcom Capri pinctrl
driver and its related CONFIG option are renamed to bcm281xx.
Devicetree compatible string and binding documentation use
"brcm,bcm11351-pinctrl" to match the machine binding here:
Documentation/devicetree/bindings/arm/bcm/bcm11351.txt
This driver supports pinctrl on BCM11130, BCM11140, BCM11351, BCM28145
and BCM28155 SoCs.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adds pinctrl driver for Broadcom Capri (BCM281xx) SoCs.
v4: - PINCTRL selected in Kconfig, PINCTRL_CAPRI selected in bcm_defconfig
- make use of regmap
- change CAPRI_PIN_UPDATE from macro to inline function.
- Handle pull-up strength arg in Ohm instead of enum
v3: Re-work driver to be based on generic pin config. Moved config selection
from Kconfig to bcm_defconfig.
v2: Use hyphens instead of underscore in DT property names.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Christian Daudt <bcm@fixthebug.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for the Tegra124 pinmux, and required
parameterization data for Tegra124.
The driver uses the common Tegra pincontrol driver utility
functions to implement the majority of the driver.
This driver is not compatible with the earlier NVIDIA's SoCs,
hence add new compatibile as "nvidia,tegra124-pinmux".
Originally written by Ashwini Gguhe.
Thierry:
- Cleanups in patches.
ldewangan:
- Fix some entries for groups.
- Fix MUX enums and group sequence.
Signed-off-by: Ashwini Ghuge <aghuge@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CC: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial definition of parameters for pinctrl-msm for the msm8x74
platform.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl, pinmux, pinconf and gpiolib driver for the
Qualcomm TLMM block.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is mostly cut and paste from the imx35 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx25.h.
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Eric Bénard <eric@eukrea.com>
Signed-off-by: Denis Carikli <denis@eukrea.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
