The ib_write_bw test allows using up to 16384 QPs. When a relatively
large number of QPs (within that range) is used, the test can fail
because the number of CQ entries needed exceeds the limit set by the
driver.
This patch increases the default setting of max_cqes from 0x2FFFF
(196607) to 0x2FFFFF(3145727), which is sufficient to cover the
maximum number needed by the ib_write_bw test (2097152). The default
setting of max_qps is also increased from 16384 to 32768 to allow
the test to run successfully with 16383 or 16384 QPs.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The FM should have full control to set the pkeys in the
driver pkey table. Remove filtering done by the driver.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
There is no need to have a global qpt_mask as that does not support the
multiple chip model which qib has. Instead rely on the value which
exists already in the device data (dd).
Fixes: 898fa52b4a "IB/qib: Remove qpn, qp tables and related variables from qib"
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This allows for adding additional pages of adaptive pio
opcode control including manufacturer specific ones.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This patch adds lockdep asserts in key code paths for
insuring lock correctness.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The call is misplaced in the reset calldown function
and causes issues with lockdep assertions that are to
be added.
Fixes: Commit a2c2d60895 ("staging/rdma/hfi1: Remove create_qp functionality")
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Existing locking scheme in affinity.c file using the
&node_affinity.lock spinlock is not very elegant.
We acquire the lock to get hfi1_affinity_node entry,
unlock, and then use the entry without the lock held.
With more functions being added, which access and
modify the entries, this can lead to race conditions.
This patch makes this locking scheme more consistent.
It changes the spinlock to mutex. Since all the code
is executed in a user process context there is no need
for a spinlock. This also allows to keep the lock
not only while we look up for the node affinity entry,
but over the whole section where the entry is being used.
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Reviewed-by: Jianxin Xiong <jianxin.xiong@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The dma_XXX API functions return bus addresses which are
physical addresses when IOMMU is disabled. Buffer
mapping to user-space is done via remap_pfn_range() with PFN
based on bus address instead of physical. This results in
wrong pages being mapped to user-space when IOMMU is enabled.
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Tymoteusz Kielan <tymoteusz.kielan@intel.com>
Signed-off-by: Andrzej Kacprowski <andrzej.kacprowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Each user SDMA request coming into the driver may contain multiple packets.
Each user packet may use multiple SDMA descriptors to fill the send buffer.
The field seqsubmitted in struct user_sdma_request counts the number of
user packets submitted to an SDMA engine. Sometimes, the intermediate count
may not be updated properly. However, once all the packets' descriptors
are successfully submitted to the SDMA engine, the final count is updated
correctly. But, if only some of the packets are submitted to the engine due
to an error, the intermediate count doesn't reflect the partial number of
packets submitted to the SDMA engine. This can cause a hang later in the
code as the count of packets submitted to the SDMA engine doesn't match the
the count of packets processed by the SDMA engine.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
All calls to tune_serdes and start_link are paired. Move
tune_serdes inside start_link.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use common header file structs, defines, and accessors
in the drivers. The old declarations are removed.
The repositioning of the includes allows for the removal
of hfi1_message_header and replaces its use with ib_header.
Also corrected are two issues with set_armed_to_active():
- The "packet" parameter is now a pointer as it should have been
- The etype is validated to insure that the header is correct
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Don Hiatt <don.hiatt@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This improves readability and hides the reference count
mechanism from the client drivers.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Set the source mac address in the FTE when L2 specification
is provided.
Fixes: 038d2ef875 ('IB/mlx5: Add flow steering support')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
MAD_IFC command is supported only for physical functions (PF)
and when physical port is IB. The proposed fix enforces it.
Fixes: d603c809ef ("IB/mlx5: Fix decision on using MAD_IFC")
Reported-by: David Chang <dchang@suse.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Modify the mlx4_ib_diag_counters() to avoid the following error in the
hypervisor when the slave tries to query the hardware counters in SR-IOV
mode.
mlx4_core 0000:81:00.0: Unknown command:0x30 accepted from slave:1
Fixes: 3f85f2aaab ("IB/mlx4: Add diagnostic hardware counters")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When sending QP1 MAD packets which use a GRH, the source GID
(which consists of the 64-bit subnet prefix, and the 64 bit port GUID)
must be included in the packet GRH.
For SR-IOV, a GID cache is used, since the source GID needs to be the
slave's source GID, and not the Hypervisor's GID. This cache also
included a subnet_prefix. Unfortunately, the subnet_prefix field in
the cache was never initialized (to the default subnet prefix 0xfe80::0).
As a result, this field remained all zeroes. Therefore, when SR-IOV
was active, all QP1 packets which included a GRH had a source GID
subnet prefix of all-zeroes.
However, the subnet-prefix should initially be 0xfe80::0 (the default
subnet prefix). In addition, if OpenSM modifies a port's subnet prefix,
the new subnet prefix must be used in the GRH when sending QP1 packets.
To fix this we now initialize the subnet prefix in the SR-IOV GID cache
to the default subnet prefix. We update the cached value if/when OpenSM
modifies the port's subnet prefix. We take this cached value when sending
QP1 packets when SR-IOV is active.
Note that the value is stored as an atomic64. This eliminates any need
for locking when the subnet prefix is being updated.
Note also that we depend on the FW generating the "port management change"
event for tracking subnet-prefix changes performed by OpenSM. If running
early FW (before 2.9.4630), subnet prefix changes will not be tracked (but
the default subnet prefix still will be stored in the cache; therefore
users who do not modify the subnet prefix will not have a problem).
IF there is a need for such tracking also for early FW, we will add that
capability in a subsequent patch.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The indentation in the QP1 GRH flow in procedure build_mlx_header is
really confusing. Fix it, in preparation for a commit which touches
this code.
Fixes: 1ffeb2eb8b ("IB/mlx4: SR-IOV IB context objects and proxy/tunnel SQP support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Because of an incorrect bit-masking done on the join state bits, when
handling a join request we failed to detect a difference between the
group join state and the request join state when joining as send only
full member (0x8). This caused the MC join request not to be sent.
This issue is relevant only when SRIOV is enabled and SM supports
send only full member.
This fix separates scope bits and join states bits a nibble each.
Fixes: b9c5d6a643 ('IB/mlx4: Add multicast group (MCG) paravirtualization for SR-IOV')
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The debugfs RCU trips many debug kernel warnings because of potential
sleeps with an RCU read lock held. This includes both user copy calls
and slab allocations throughout the file.
This patch switches the RCU to use SRCU for file remove/access
race protection.
In one case, the SRCU is implicit in the use of the raw debugfs file
object and just works.
In the seq_file case, a wrapper around seq_read() and seq_lseek() is
used to enforce the SRCU using the debugfs supplied functions
debugfs_use_file_start() and debugfs_use_file_stop().
The sychronize_rcu() is deleted since the SRCU prevents the remove
access race.
The RCU locking is kept for qp_stats since the QP hash list is
protected using the non-sleepable RCU.
Reviewed-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The global variable n_krcvqs stores the sum of the number of kernel
receive queues of VLs 0-7 which the user can pass to the driver through
the module parameter array krcvqs which is of type unsigned integer. If
the user passes large value(s) into krcvqs parameter array, it can cause
an arithmetic overflow while calculating n_krcvqs which is also of type
unsigned int. The overflow results in an incorrect value of n_krcvqs
which can lead to kernel crash while loading the driver.
Fix by changing the data type of n_krcvqs to unsigned long. This patch
also changes the data type of other variables that get their values from
n_krcvqs.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Sometimes a QSFP device does not respond in the expected time
after a power-on. Add a read pre-check/retry when starting
the link on driver load.
Reviewed-by: Easwar Hariharan <easwar.hariharan@intel.com>
Signed-off-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In the set_txreq_header_ahg(), The KDETH Intr bit is obtained from the
header in the user sdma request using a KDETH_GET shift and mask macro.
This value is then futher right shifted by 16 causing us to lose the
value i.e it is shifted to zero, leading to the following
smatch warning:
drivers/infiniband/hw/hfi1/user_sdma.c:1482 set_txreq_header_ahg()
warn: mask and shift to zero
The Intr bit should be left shifted into its correct position in the
KDETH header before the AHG update.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Mitko Haralanov <mitko.haralanov@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Signed-off-by: Jubin John <jubin.john@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
When trying to align the source pointer and there's a byte carry
in an SGE copy, bytes are borrowed from the next quad-word X to
complete the required quad-word copy. Then, the SGE length is
reduced by the number of borrowed bytes. After this, if the
remaining number of bytes from quad-word X (extra bytes) is
greater than the new SGE length, the number of extra bytes needs
to be updated to the new SGE length. Otherwise, when the
SGE length gets updated again after the extra bytes are read to
create the new byte carry, it goes negative, which then becomes
a very large number as the SGE length is an unsigned integer.
This causes SGE buffer to be over-read.
Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove returning errors from mlx5 poll_cq function. Polling CQ
operation in kernel never fails by Mellanox HCA architecture and
respective driver design.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Use TIR number based on selector, it should be done to differentiate
between RSS QP to RAW one.
Reported-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Tested-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Return variable was set in a line before the
actual return was called in begin_wqe function.
This patch removes such variable and simplifies the code.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The returned value should be EINVAL, because it is caused by wrong
caller and not by internal overflow event.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Remove returning errors from mlx4 poll_cq function. Polling CQ
operation in kernel never fails by Mellanox HCA architecture and
respective driver design.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
By Mellanox HW design and SW implementation, poll_cq never
fails and returns errors, so all these printks are to catch ULP bugs.
In case of such bug, the reverted patch will cause reentry of the
function, resulting in a printk storm.
This reverts commit 5412352fcd ("IB/mlx4: Return EAGAIN for any error in mlx4_ib_poll_one")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
We get 1 warning when build kernel with W=1:
drivers/infiniband/hw/cxgb4/qp.c:686:6: warning: no previous prototype for '_free_qp' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(u64)' which is 8.
It is likely that the number of bits of 'port_mask' was expected here.
Use sizeof() * 8 to get the correct number.
It has been spotted by the following coccinelle script:
@@
expression ret, x;
@@
* ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 2nd parameter of 'find_first_bit' is the number of bits to search.
In this case, we are passing 'sizeof(tmp)' which is likely to be 4 or 8
because 'tmp' is an 'unsigned long'.
It is likely that the number of bits of 'tmp' was expected here. So use
BITS_PER_LONG instead.
It has been spotted by the following coccinelle script:
@@
expression ret, x;
@@
* ret = \(find_first_bit \| find_first_zero_bit\) (x, sizeof(...));
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Majd Dibbiny <majd@mellanox.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In all other places in this file where 'find_first_bit' is called,
port_num is defined as a 'u8' and no casting is done.
Do the same here in order to be more consistent.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Device notifications are not received after the first interface is
closed; since there is an unregister for notifications on every
interface close. Correct this by unregistering for device
notifications only when the last interface is closed. Also, make
all operations on the i40iw_notifiers_registered atomic as it
can be read/modified concurrently.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Update iwqp->hw_iwarp_state to reflect the new state of the CQP
modify QP operation. This avoids reissuing a CQP operation to
modify a QP to a state that it is already in.
Fixes: 4e9042e647 ("i40iw: add hw and utils files")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Send a zero length last streaming mode message for loopback
connections to synchronize between accepting QP and connecting QP.
This avoids data transfer to start on the accepting QP before
the connecting QP is in RTS. Also remove function i40iw_loopback_nop()
as it is no longer used.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Signed-off-by: Tatyana Nikolova <tatyana.e.nikolova@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current driver is reporting wrong values for max_sge and
max_sge_rd in query_device. This breaks the nfs rdma and iser
in some device profiles. Fixing the driver to report
correct values from FW.
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iwpbl->iwmr points to the structure that contains iwpbl,
which is iwmr. Setting this to NULL would result in
writing to freed memory. So just free iwmr, and return.
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Memory allocated for iwqp; iwqp->allocated_buffer is freed twice in
the create_qp error path. Correct this by having it freed only once in
i40iw_free_qp_resources().
Fixes: d374984179 ("i40iw: add files for iwarp interface")
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
This file does not use any structs or functions defined by io-mapping.h
(nor does it directly use iomap, ioremap, iounamp or friends). Remove it
to simplify verification of changes to io-mapping.h
The include existed since its inception in
commit e126ba97db
Author: Eli Cohen <eli@mellanox.com>
Date: Sun Jul 7 17:25:49 2013 +0300
mlx5: Add driver for Mellanox Connect-IB adapters
which looks like a copy across from the Mellanox ethernet driver.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eli Cohen <eli@mellanox.com>
Cc: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Matan Barak <matanb@mellanox.com>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Doug Ledford <dledford@redhat.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: linux-rdma@vger.kernel.org
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_free_virt_mem(), do not set mem->va to NULL
after freeing it as mem->va is a self-referencing pointer
to mem.
Fixes: 4e9042e647 ("i40iw: add hw and utils files")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add NULL check for pdata and pdata->addr before the memcpy in
i40iw_form_cm_frame(). This fixes a NULL pointer de-reference
which occurs when the MPA private data pointer is NULL. Also
only copy pdata->size bytes in the memcpy to prevent reading
past the length of the private data buffer provided by upper layer.
Fixes: f27b4746f3 ("i40iw: add connection management code")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Current cxgb4 arm CQ logic ignores IB_CQ_REPORT_MISSED_EVENTS for
request completion notification on a CQ. Due to this ib_poll_handler()
assumes all events polled and avoids further iopoll scheduling.
This patch adds logic to cxgb4 ib_req_notify_cq() handler to check if
CQ is not empty and return accordingly. Based on the return value of
ib_req_notify_cq() handler, ib_poll_handler() will schedule a run of
iopoll handler.
Signed-off-by: Potnuri Bharat Teja <bharat@chelsio.com>
Reviewed-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_open(), check if interface is already open
and return success if it is.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In i40iw_alloc_resource(), ensure that the update to
req_resource_num is protected by the lock.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
iwdev->mem_resources is incorrectly defined as an unsigned
long instead of u8. As a result, the offset into the dynamic
allocated structures in i40iw_initialize_hw_resources() is
incorrectly calculated and would lead to writing of memory
regions outside of the allocated buffer.
Fixes: 8e06af711b ("i40iw: add main, hdr, status")
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Mustafa Ismail <mustafa.ismail@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw initiator sends an MPA-request with ird=16 and ord=16. The cxgb4
responder sends an MPA-reply with ord = 32 causing i40iw to terminate
due to insufficient resources.
The logic to reduce the ORD to <= peer's IRD was wrong.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The i40iw initiator sends an MPA-request with ird = 63, ord = 63. The
cxgb4 responder sends a RST. Since the inbound ord=63 and it exceeds
the max_ird/c4iw_max_read_depth (=32 default), chelsio decides to abort.
Instead, cxgb4 should adjust the ord/ird down before presenting it to
the ULP.
Reported-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
