This is useful for debugging issues with drivers using this
function (erroneously), so add tracing for the API call.
Change-Id: Ice9d7eabb8fecbac188f0a741920d3488de700ec
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix a number of different checkpatch errors.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.
Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.
This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.
The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit 488b366a45.
The code isn't used by anyone, and the Intel driver isn't planning
to use it either right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.
Tuning to a narrower channel might help reducing
the noise level and saving some power.
The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.
In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).
In other cases, simply use bss_conf.chandef as the
min required chandef.
Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This can be useful for drivers if they have any failure cases
when joining an IBSS. Also move setting the queue parameters
to before this new call, in case the new driver op needs them
already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add P2P NoA settings for STA mode.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
[fix docs]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices have multicast filter capability for each individual
virtual interface rather than just a global one. Add an interface
specific driver callback allowing such drivers to configure this.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several tracepoints are using STA_PR_FMT where STA_PR_ARG should be
used, resulting in messages like "phy0 sta:ARG TYPE NOT FIELD BUT 1".
Change these to STA_PR_ARG.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to be able to predict the next DTIM TBTT
in the driver, add the ability to use timing data
from beacons only with the new hardware flag
IEEE80211_HW_TIMING_BEACON_ONLY and the BSS info
value sync_dtim_count which is only valid if the
timing data came from a beacon. The data can only
come from a beacon, and if no beacon was received
before association it is updated later together
with the DTIM count notification.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The chandef tracing writes center_freq1 twice, so
that it is always 0 (no driver supports 80+80 yet)
and leaves center_freq2 unset. Fix this mistake.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.
Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.
When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some new APIs will require tracing a chandef without
it being part of a channel context, so separate out
the tracing macros for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.
Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers (e.g. wl12xx) might need to know the vif
to roc on (mainly in order to configure the
rx filters correctly).
Add the vif to the op params, and update the current
users (iwlwifi) to use the new api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
[fix hwsim]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver requests a restart (reconfiguration) it
gets all the normal method calls, but can't really tell
why they're happening. Call a new restart_complete op
in the driver when the restart completes, so it could
keep its own state about the restart and clear it there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Clearly the tracepoint drv_offchannel_tx was
forgotten when that functionality was removed,
remove it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While connected to a GO, parse the P2P NoA attribute
and pass the CT Window and opportunistic powersave
parameters to the driver.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even before channel contexts/multi-channel, having a
single global TX power limit was already problematic,
in particular if two managed interfaces connected to
two APs with different power constraints. The channel
context introduction completely broke this though and
in fact I had disabled TX power configuration there
for drivers using channel contexts.
Change everything to track TX power per interface so
that different user settings and different channel
maxima are treated correctly. Also continue tracking
the global TX power though for compatibility with
applications that attempt to configure the wiphy's
TX power globally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On each channel that the device is operating on, it
may need to listen using one or more chains depending
on the SMPS settings of the interfaces using it. The
previous channel context changes completely removed
this ability (before, it was available as the SMPS
mode).
Add per-context tracking of the required static and
dynamic RX chains and notify the driver on changes.
To achieve this, track the chains and SMPS mode used
on each virtual interface and update the channel
context whenever this changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Introduce channel context driver methods. The channel
on a context channel is immutable, but the channel type
and other properties can change.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With the move to multi-channel and away from
drv_config(), hw.conf.channel will not always
be set, only for devices using the current API
instead of the new channel context APIs. Check
the channel is set before adding its frequency
to the trace data.
Also break some overly long lines in the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After cfg80211 got a P2P Device abstraction, add
support to mac80211. Whether it really is supported
or not will depend on whether or not the driver has
support for it, but mac80211 needs to change to be
able to support drivers that need a P2P Device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers (iwlegacy, iwlwifi and rt2x00) today use the
bss_conf.last_tsf value. By itself though that value is
completely worthless since it may be ancient. What really
is needed is synchronisation between some device time and
the TSF.
To clarify this, rename bss_conf.last_tsf to sync_tsf and
add sync_device_ts which is obtained from rx_status which
gets a new field device_timestamp for this purpose. This
is intentionally not using the mactime field since that
is used for other things and in IBSS is expected to sync
with the IBSS's TSF which isn't necessarily true for the
device timestamp.
Also, since we have the information and it's useful even
before the connection has been established, give all the
timing details to the driver before authenticating.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some drivers require setup before being able to send
management frames in managed mode, in particular in
multi-channel cases.
Introduce API to allow the drivers to do such setup
while being able to sleep waiting for the setup to
finish in the device. This isn't possible inside the
TX call since that can't sleep.
A future patch may also restructure the TX retry to
wait for the driver to report the frame status, as
suggested by Arik in
http://mid.gmane.org/CA+XVXffKSEL6ZQPQ98x-zO-NL2=TNF1uN==mprRyUmAaRn254g@mail.gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It can be very useful to have all debug messages
available when debugging, but hard to correlate
between different sources, so add a trace event
for all mac80211 debug messages.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
