Pin PH11 is used on various A83T board to detect a change in the OTG
port's ID pin, as in when an OTG host cable is plugged in.
The incorrect offset meant the gpiochip/irqchip was activating the wrong
pin for interrupts.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We just changed the code so we apply bias disable on the correct
register but forgot to align the register calculation. The result
is that we apply the change on the correct register, but possibly
at the incorrect offset/bit
This went undetected because offsets tends to be the same between
REG_PULL and REG_PULLEN for a given pin the EE controller. This
is not true for the AO controller.
Fixes: e39f9dd820 ("pinctrl: meson: fix pinconf bias disable")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This was missed when tiles support was added in a revison and
causes the driver to fail to load.
Fixes: 9cf0c526bc ("pinctrl: qcom: Add sdm660 pinctrl driver")
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
AO pull register definition is inverted between pull (up/down) and
pull enable. Fixing this allows to properly apply bias setting
through pinconf
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a bias is enabled on a pin of an Amlogic SoC, calling .pin_config_set()
with PIN_CONFIG_BIAS_DISABLE will not disable the bias. Instead it will
force a pull-down bias on the pin.
Instead of the pull type register bank, the driver should access the pull
enable register bank.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
There were no significant changes to the core this time!
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO
subsystem and consolidated it all in the Ingenic pin control
driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin
controller family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else.
-----BEGIN PGP SIGNATURE-----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=rBtH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.20 series:
There were no significant changes to the core this time! Bur the new
Qualcomm, Mediatek and Broadcom drivers are quite interesting as they
will be used in a few million embedded devices the coming years as it
seems.
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO subsystem
and consolidated it all in the Ingenic pin control driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin controller
family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else"
* tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (153 commits)
pinctrl: sunxi: Fix a memory leak in 'sunxi_pinctrl_build_state()'
gpio: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
pinctrl: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
dt-bindings: pinctrl: bcm4708-pinmux: improve example binding
pinctrl: geminilake: Sort register offsets by value
pinctrl: geminilake: Get rid of unneeded ->probe() stub
pinctrl: geminilake: Update pin list for B0 stepping
pinctrl: renesas: Fix platform_no_drv_owner.cocci warnings
pinctrl: mediatek: Make eint_m u16
pinctrl: bcm: ns: Use uintptr_t for casting data
pinctrl: madera: Fix uninitialized variable bug in madera_mux_set_mux
pinctrl: gemini: Fix up TVC clock group
pinctrl: gemini: Drop noisy debug prints
pinctrl: gemini: Mask and set properly
pinctrl: mediatek: select GPIOLIB
pinctrl: rza1: don't manually release devm managed resources
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: bcm: add Northstar driver
dt-bindings: pinctrl: document Broadcom Northstar pin mux controller
pinctrl: qcom: fix 'const' pointer handling
...
If 'krealloc()' fails, 'pctl->functions' is set to NULL.
We should instead use a temp variable in order to be able to free the
previously allocated memeory, in case of OOM.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reason of including <linux/bitops.h> here is just for BIT() macro.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The local ->probe() stub does nothing except calling
a generic Intel pin control probe function. Thus,
it's not needed and generic function may be called directly.
This patch converts the driver accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to an updated pin list few names of the pins can be spelled better,
taking into account their primary functions.
Thus, update a pin list to cover B0 stepping.
Note, SPI numbering had been fixed even in A0 public documentation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For SoC's which lacks EINT support, U16_MAX is assigned to both eint_m
and eint_n through macro NO_EINT_SUPPORT. This will generate integer
overflow warning because eint_m is declared as u8 type. Hence modify
the eint_m type to u16.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix up a compiler error on 64bit architectures where pointers
and integers differ in size.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a potential execution path in which variable *ret* is checked
in an IF statement, and then its value is used to report an error at
line 659 without being properly initialized previously:
659 if (ret)
660 dev_err(priv->dev, "Failed to write to 0x%x (%d)\n", reg, ret);
Fix this by initializing variable *ret* to 0 in order to
avoid unpredictable or unintended results.
Addresses-Coverity-ID: 1471969 ("Uninitialized scalar variable")
Fixes: 218d72a77b ("pinctrl: madera: Add driver for Cirrus Logic Madera codecs")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The previous fix made the TVC clock get muxed in on the
D-Link DIR-685 instead of giving nagging warnings of this
not working. Not good. We didn't want that, as it breaks
video.
Create a specific group for the TVC CLK, and break out
a specific GPIO group for it on the SL3516 so we can use
that line as GPIO if we don't need the TVC CLK.
Fixes: d17f477c5b ("pinctrl: gemini: Mask and set properly")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since 'commit 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")' the
irq request isn't the last devm_* allocation. Without a deeper look at
the irq and testing this isn't a good solution. Since this driver relies
on the devm mechanism, requesting a interrupt should be the last thing
to avoid memory corruptions during unbinding.
'Commit 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")' fixed the
order for the interrupt-controller use case only. The
mcp23s08_irq_setup() must be split into two to fix it for the
interrupt-controller use case and to register the irq at last. So the
irq will be freed first during unbind.
Cc: stable@vger.kernel.org
Cc: Jan Kundrát <jan.kundrat@cesnet.cz>
Cc: Dmitry Mastykin <mastichi@gmail.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Fixes: 82039d244f ("pinctrl: mcp23s08: add pinconf support")
Fixes: 02e389e63e ("pinctrl: mcp23s08: fix irq setup order")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The code was written under the assumption that the
regmap_update_bits() would mask the bits in the mask and
set the bits in the value.
It missed the points that it will not set bits in the value
unless these are also masked in the mask. Set value bits
that are not in the mask will simply be ignored.
Fixes: 06351d133d ("pinctrl: add a Gemini SoC pin controller")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Removing the linux/gpio.h include means we no longer have a declaration
of gpiochip_lock_as_irq() when CONFIG_GPIOLIB is disabled:
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_request_resources':
drivers/pinctrl/mediatek/mtk-eint.c:247:8: error: implicit declaration of function 'gpiochip_lock_as_irq'; did you mean 'spin_lock_irq'? [-Werror=implicit-function-declaration]
drivers/pinctrl/mediatek/mtk-eint.c: In function 'mtk_eint_irq_release_resources':
drivers/pinctrl/mediatek/mtk-eint.c:272:2: error: implicit declaration of function 'gpiochip_unlock_as_irq'; did you mean 'spin_unlock_irq'? [-Werror=implicit-function-declaration]
Select it explictly instead.
Fixes: 1c5fb66afa ("pinctrl: Include <linux/gpio/driver.h> nothing else")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the probe function fails the driver core cares to return the allocated
resources automatically. So the driver can be simplified accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add support for the new RZ/N1D (R9A06G032) and RZ/N1S (R9A06G033)
SoCs,
- Add INTC-EX pin groups on R-Car E3.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW7dQmQAKCRCKwlD9ZEnx
cB04AQCj1PoCEotqH9TGaGeVXal35LUMP279vz3HoJweY0DF2AD/QKd/jC2mHz/c
EypfJAvBvckw9AsdfNSacrCIdMNg7gE=
=gtgr
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.20-tag3' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.20 (take three)
- Add support for the new RZ/N1D (R9A06G032) and RZ/N1S (R9A06G033)
SoCs,
- Add INTC-EX pin groups on R-Car E3.
The current code produces XPU violation if get_direction is called just
after the initialization.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Timur Tabi <timur@kernel.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver provides support for Northstar mux controller. It differs
from Northstar Plus one so a new binding and driver were needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'tiles' array is initialized to a constant pointers to constant
strings, but the declaration is only half as constant:
drivers/pinctrl/qcom/pinctrl-qcs404.c:1660:11: error: initialization discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
drivers/pinctrl/qcom/pinctrl-sdm660.c:1417:11: error: initialization discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
Let's make it more constant.
Fixes: 22eb8301db ("pinctrl: qcom: Add qcs404 pinctrl driver")
Fixes: a46d5e9819 ("pinctrl: qcom: Support dispersed tiles")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .to_irq() function obviously takes the per-chip offset
as parameter, not the global GPIO number.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The parameter 'community' had been spelled incorrectly.
Fix it here.
As a side effect it satisfies static checkers that issue
the following warnings:
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Function parameter or member 'community' not described in 'intel_gpio_to_pin'
drivers/pinctrl/intel/pinctrl-intel.c:845: warning: Excess function parameter 'commmunity' description in 'intel_gpio_to_pin'
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simple type conversion with no functional change implied.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and function for the Interrupt Controller for
External Devices (INTC-EX) on the R-Car E3 SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This provides a pinctrl driver for the Renesas RZ/N1 device family.
Based on a patch originally written by Michel Pollet at Renesas.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This code needs to select function #0, which is the first int in the
array of functions, not the number 0 which may or may not be the
function for "GPIO mode" per the enum mapping. We were getting lucky on
SDM845, where this was tested, because the function 0 matched the enum
value for "GPIO mode". On other platforms, e.g. MSM8996, the gpio enum
value is the last one in the list so this code doesn't work and we see a
warning at boot. Fix it by grabbing the first element out of the array
of functions.
Cc: Doug Anderson <dianders@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Fixes: 1de7ddb3a1 ("pinctrl: msm: Mux out gpio function with gpio_request()")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some drivers, for example, QCOM's qdf2xxx, set groups[gpio].name only
when gpio is valid, and leave invalid gpio names as null.
If we want to access the sys node "pinconf-groups",
pinctrl_get_group_selector() -> get_group_name() may return a null
pointer if group_selector is invalid, then the below Kernel panic
would happen since strcmp() uses this null pointer to do comparison.
Unable to handle kernel NULL pointer dereference at ss 00000000
el:Internal error: Oops: 9600000[ 143.080279]
SMP
CPU: 19 PID: 2493 Comm: read_all Tainted: G O
.aarch64 #1
Hardware name: HXT Semiconductor HXT REP-2 System
PC is at strcmp+0x18/0x154
LR is at pinctrl_get_group_selector+0x6c/0xe8
Process read_all (pid: 2493, stack limit =
Call trace:
Exception stack
strcmp+0x18/0x154
pin_config_group_get+0x64/0xd8
pinconf_generic_dump_one+0xd8/0x1c0
pinconf_generic_dump_pins+0x94/0xc8
pinconf_groups_show+0xb4/0x104
seq_read+0x178/0x464
full_proxy_read+0x6c/0xac
__vfs_read+0x58/0x178
vfs_read+0x94/0x164
SyS_read+0x60/0xc0
__sys_trace_return+0x0/0x4
--[ end trace]--
Kernel panic - not syncing: Fatal exception
Signed-off-by: Yanjiang Jin <yanjiang.jin@hxt-semitech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add MSIOF pin groups on R-Car E3 and D3,
- Add support for the new RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs,
- Add I2C4, DU0, QSPI0, SDHI2, and USB pin groups on RZ/G1C,
- Convert to SPDX license identifiers,
- Small cleanups.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCW63oXAAKCRCKwlD9ZEnx
cEZ3AP4zgrTOnA9iDjgqMPtkaHcIX4b2R8fykZeRBs0J5u9R3QD/Y4JqDXF/AbVB
fAX+GuCf1oMOflFlde7Dpp1nDYIaAg8=
=0a9P
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.20-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.20 (take two)
- Add MSIOF pin groups on R-Car E3 and D3,
- Add support for the new RZ/G1N (R8A7744) and RZ/G2E (R8A774C0) SoCs,
- Add I2C4, DU0, QSPI0, SDHI2, and USB pin groups on RZ/G1C,
- Convert to SPDX license identifiers,
- Small cleanups.
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rc6' into devel
This is the 4.19-rc6 release
I needed to merge this in because of extensive conflicts in
the MSM and Intel pin control drivers. I know how to resolve
them, so let's do it like this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Renesas RZ/G SoCs are pin compatible with R-Car SoCs, but lack several
automotive-specific peripherals.
Currently pin groups and functions for automotive-specific peripherals
are grouped in arrays named after the automative SoC part numbers.
Rename them to "automotive" for clarity and consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
It will be failed to select default or sleep state for pins hogged
by the pin controller device, since we hadn't parsed pins configuration
in device tree before registering the pin controller device. Thus
we should move the device tree parsing function before registering
the pin controller device.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mtk_eint_set_debounce and mtk_eint_find_irq are defined as stub functions
in a header file, but without marking them as 'static inline', we get
a copy for each file that includes the header:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o: In function `mtk_eint_set_debounce':
pinctrl-mtk-common-v2.c:(.text+0x134): multiple definition of `mtk_eint_set_debounce'
drivers/pinctrl/mediatek/pinctrl-moore.o:pinctrl-moore.c:(.text+0x7d0): first defined here
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.o: In function `mtk_eint_find_irq':
pinctrl-mtk-common-v2.c:(.text+0x13c): multiple definition of `mtk_eint_find_irq'
Fixes: e46df235b4 ("pinctrl: mediatek: refactor EINT related code for all MediaTek pinctrl can fit")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, the check on desc->eint.eint_n == EINT_NA is always false
because this is comparing a u16 to -1 which can never be true. Fix
this by casting EINT_NA to u16.
Detected by CoverityScan, CID#1473610 ("Operands don't affect result")
Fixes: fb5fa8dc15 ("pinctrl: mediatek: extend struct mtk_pin_desc to pinctrl-mtk-common-v2.c")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration with
pinctrl framework for qcs404.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Signed-off-by: Chintan Pandya <cpandya@codeaurora.org>
Signed-off-by: Anu Ramanathan <anur@codeaurora.org>
[bjorn: Reworked tile handling and did some minor rework]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some new platforms the tiles have been placed too far apart to be
covered in a single ioremap. Turn "regs" into an array of base addresses
and make the pingroup carry the information about which tile the pin
resides in.
For existing platforms we map the first entry regs and the existing
pingroups will all use tile 0, meaning that there's no functional
change.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation for the support for dispersed tiles move all readl and
writel calls to helper functions. This will allow us to isolate the
added complexity of another indirection.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 55aedef50d.
Commit 55aedef50d ("pinctrl: intel: Do pin translation when lock IRQ")
added special translation from GPIO number to hardware pin number to
irq_reqres/relres hooks to avoid failure when IRQs are requested. The
actual failure happened inside gpiochip_lock_as_irq() because it calls
gpiod_get_direction() and pinctrl-intel.c::intel_gpio_get_direction()
implementation originally missed the translation so the two hooks made
it work by skipping the ->get_direction() call entirely (it overwrote
the default GPIOLIB provided functions).
The proper fix that adds translation to GPIO callbacks was merged with
commit 96147db1e1 ("pinctrl: intel: Do pin translation in other GPIO
operations as well"). This allows us to use the default GPIOLIB provided
functions again.
In addition as find out by Benjamin Tissoires the two functions
(intel_gpio_irq_reqres()/intel_gpio_irq_relres()) now cause problems of
their own because they operate on pin numbers and pass that pin number
to gpiochip_lock_as_irq() which actually expects a GPIO number.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199911
Fixes: 55aedef50d ("pinctrl: intel: Do pin translation when lock IRQ")
Reported-and-tested-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
