Recent commit 8da645e101
sctp: Get rid of an extra routing lookup when adding a transport
introduced a regression in the connection setup. The behavior was
different between IPv4 and IPv6. IPv4 case ended up working because the
route lookup routing returned a NULL route, which triggered another
route lookup later in the output patch that succeeded. In the IPv6 case,
a valid route was returned for first call, but we could not find a valid
source address at the time since the source addresses were not set on the
association yet. Thus resulted in a hung connection.
The solution is to set the source addresses on the association prior to
adding peers.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainline commit 53ef99cad9 removed the
JBD compatibility layer from OCFS2. This patch removes the last remaining
remnants of that.
Signed-off-by: Sunil Mushran <sunil.mushran@oracle.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
The size of buf[] must account for the string termination needed for
the first strict_strtoul() call. Introduced in commit a02d6926.
Fábio Olivé Leite points out that strict_strtoul() requires _either_
'\n\0' _or_ '\0' termination, so use the simpler '\0' here instead.
See http://bugzilla.kernel.org/show_bug.cgi?id=14546 .
Reported-by: argp@census-labs.com
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Fábio Olivé Leite <fleite@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Add myself to the list of maintainers for the rt2x00 driver.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b8ecd988b1.
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The addition of rcv_nxt allows to discern whether the skb
was out of place or tp->copied. Also catch fancy combination
of flags if necessary (sadly we might miss the actual causer
flags as it might have already returned).
Btw, we perhaps would want to forward copied_seq in
somewhere or otherwise we might have some nice loop with
WARN stuff within but where to do that safely I don't
know at this stage until more is known (but it is not
made significantly worse by this patch).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable propagation of mbus errors to the CPU local bus, as this causes
mbus errors (which can occur for example for PCI aborts) to throw CPU
aborts, which we're not set up to deal with.
Reported-by: Dieter Kiermaier <dk-arm-linux@gmx.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
1. At the end of smtc_distribute_timer, nextstamp is valid and has already
passed so we goto repeat.
2. Nothing updates nextstamp (only updated if the timeout is in the future
And we just decided it is in the past)
3. At the end nextstamp still has the same value so it is still valid and
in the past.
4. This repeats until read_c0_count has a value which causes nextstamp to
be in the future.
Reported and initial patch and testing by Mikael Starvik
<mikael.starvik@axis.com>.
Signed-off-by: Kevin D. Kissell <kevink@paralogos.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: linux-mips@linux-mips.org
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Patchwork: http://patchwork.linux-mips.org/patch/621/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 22242681cf ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.
Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to to declare these arrays static with __initdata.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ohci-sm501 driver requires dma_declare_coherent_memory(). It is used
by the driver's local memory allocation with dma_alloc_coherent().
Tested on TANBAC TB0287(VR4131 + SM501).
[Ralf: Fixed reject in dma-default.c and removed the entire #if 0'ed block
in dma-mapping.h instead of just the #if 0.]
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Running a 64-bit kernel on a 64-bit CPU without an FPU would cause the
emulator to run in 32-bit mode. The c0_Status.FR bit is wired to zero
on systems without an FPU, so using that bit to decide how the emulator
behaves doesn't allow for proper emulation on 64-bit FPU-less
processors.
Instead, we need to select the emulator mode based on the user-space
ABI. Since the thread flag TIF_32BIT_REGS is used to set c0_Status.FR,
we can just use it to decide if the emulator should be in 32-bit or
64-bit mode.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On s390 there are two ways of specifying the system call number for
the svc instruction. The standard way is to use the immediate field
in the instruction (or to use EXecute for values unknown during
assemble time). This can encode 256 system calls.
The kernel ABI also allows to put the system call number in r1 and
then execute svc 0 to enable system call numbers > 255.
It turns out that single stepping svc 0 is broken, since the PER
program check handler uses r1. We have to use a different register.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In a system where the ctrl-alt-del init action initiated by signal
quiesce suspends the machine the quiesce handler override for
_machine_restart, _machine_halt and _machine_power_off needs to be
undone, otherwise the override is still present in the resumed
system. The next shutdown would then load the quiesce state psw
instead of performing the correct shutdown action.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After an IPL from NSS the uptime of the system is incorrect. The reason
is that the startup code in head.S is not executed in case of an IPL
from NSS. Due to that sched_clock_base_cc which is used to initialze
wall_to_monotonic contains the time stamp when the NSS has been created
instead of the time stamp of the system start.
Reinitialize the cputime accounting values in create_kernel_nss after
the SAVESYS CP command that created the NSS segment.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The monreader device driver doesn't set dev->driver_data to NULL after
freeing the corresponding data structure. This leads to a use after
free bug in the freeze/thaw suspend/resume functions after the device
has been opened and closed once. Fix this by clearing dev->driver_data
in the close() function.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Since MFP_PIN_GPIO* now includes 128-255, mfp_to_gpio() is no longer
valid for those additional pins, fix it.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The AC97 part wasn't initialized on Colibri/PXA320 because the macros
were wrong. Also, the code didn't compile because of a header file not
being included.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Commit d2c3706842 ([ARM] pxa:
initialize default interrupt priority and use ICHP for IRQ handling)
broke ISA interrupt support on pxa27x/3xx.
In such a case, PXA_IRQ(0) != 0, and the IRQ number computed from
ICHP must be offset by PXA_IRQ(0).
Tested on an Arcom Zeus (pxa270), with both CONFIG_PXA_HAVE_ISA_IRQS
enabled and disabled.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Tested-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should be sending EV_LED event down to drivers upon resume even in cases
when in-kernel state of the LED is off since device could come up with some
leds turned on.
Reported-and-tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Normally is it not safe to allow a raid5 that is both dirty and
degraded to be assembled without explicit request from that admin, as
it can cause hidden data corruption.
This is because 'dirty' means that the parity cannot be trusted, and
'degraded' means that the parity needs to be used.
However, if the device that is missing contains only parity, then
there is no issue and assembly can continue.
This particularly applies when a RAID5 is being converted to a RAID6
and there is an unclean shutdown while the conversion is happening.
So check for whether the degraded space only contains parity, and
in that case, allow the assembly.
Signed-off-by: NeilBrown <neilb@suse.de>
When a reshape finds that it can add spare devices into the array,
those devices might already be 'in_sync' if they are beyond the old
size of the array, or they might not if they are within the array.
The first case happens when we change an N-drive RAID5 to an
N+1-drive RAID5.
The second happens when we convert an N-drive RAID5 to an
N+1-drive RAID6.
So set the flag more carefully.
Also, ->recovery_offset is only meaningful when the flag is clear,
so only set it in that case.
This change needs the preceding two to ensure that the non-in_sync
device doesn't get evicted from the array when it is stopped, in the
case where v0.90 metadata is used.
Signed-off-by: NeilBrown <neilb@suse.de>
This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.
Signed-off-by: NeilBrown <neilb@suse.de>
pcpu_extend_area_map() had the following two bugs.
* It should return 1 if pcpu_lock was dropped and reacquired but it
returned 0. This could lead to oops if free_percpu() races with
area map extension.
* pcpu_mem_free() was called under pcpu_lock. pcpu_mem_free() might
end up calling vfree() which isn't IRQ safe. This could lead to
deadlock through lock order inversion via IRQ.
In addition, Linus pointed out that the temporary lock dropping and
subtle three-way return value of pcpu_extend_area_map() was very ugly
and suggested to split the function into two - pcpu_need_to_extend()
and pcpu_extend_area_map().
This patch restructures pcpu_extend_area_map() as suggested and fixes
the two bugs.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Because of an integer overflow on start_blk, various kind of wrong results
would be returned by the generic_block_fiemap() handler, such as no
extents when there is a 4GB+ hole at the beginning of the file, or wrong
fe_logical when an extent starts after the first 4GB.
Signed-off-by: Mike Hommey <mh@glandium.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Eric Sandeen <sandeen@sgi.com>
Cc: Josef Bacik <jbacik@redhat.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PPS events must be recorded according to PPS's mode settings.
If a process asks for (i.e.) capture-assert events only, when the PPS
client calls the pps_event() function to save the current PPS event, we
should verify the event type and then discard unwanted ones.
Also, without this patch userland processes waiting for a specific PPS
event (assert or clear but not both) may be awakened at wrong time.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: William S. Brasher <billb958@door.net>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Userland programs may read/write PPS parameters at same time and these
operations may corrupt PPS data.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TASK_INTERRUPTIBLE and friends are now only available after including
<linux/sched.h>, so include it when needed.
bus_id is no longer available/necessary, so remove that.
Android pmem driver is not available in mainline, so remove its hooks
from drivers/video.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails. Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
v3020_mmio_read_bit() always returns 0 when left_shift > 7.
v3020_mmio_read_bit()'s return type is (unsigned char). The code returns
a value masked by (1 << left_shift) that is casted to the return type. If
left_shift is larger than 7, the cast will always result in a 0 return
value. The problem was discovered with left_shift = 16, and the included
patch corrects the problem.
The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-vr41xx.c: In function 'vr41xx_rtc_irq_set_freq':
drivers/rtc/rtc-vr41xx.c:217: warning: comparison of distinct pointer types lacks a cast
drivers/rtc/rtc-vr41xx.c:217: warning: right shift count >= width of type
drivers/rtc/rtc-vr41xx.c:217: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In setup_arg_pages we work hard to assign a value to ret, but on exit we
always return 0.
Also remove a now duplicated exit path and branch to out_unlock instead.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The config FB_PRE_INIT_FB entry in drivers/video/Kconfig pushes all entries
below it out of the menuconfig selection. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use git.kernel.org not www.kernel.org
Signed-off-by: Joe Perches <joe@perches.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct uart_port::iobase is unsigned long, so use %lx as printk format
specifier.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
