When Qav mode is enabled, queue 0 should be kept on Stream Reservation
mode. From the i210 datasheet, section 8.12.19:
"Note: Queue0 QueueMode must be set to 1b when TransmitMode is set to
Qav." ("QueueMode 1b" represents the Stream Reservation mode)
The solution is to give queue 0 the all the credits it might need, so
it has priority over queue 1.
A situation where this can happen is when cbs is "installed" only on
queue 1, leaving queue 0 alone. For example:
$ tc qdisc replace dev enp2s0 handle 100: parent root mqprio num_tc 3 \
map 2 2 1 0 2 2 2 2 2 2 2 2 2 2 2 2 queues 1@0 1@1 2@2 hw 0
$ tc qdisc replace dev enp2s0 parent 100:2 cbs locredit -1470 \
hicredit 30 sendslope -980000 idleslope 20000 offload 1
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.
Taken from cfi_cmdset_0001 driver.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Some Micron chips does not work well wrt Erase suspend for
boot blocks. This avoids the issue by not allowing Erase suspend
for the boot blocks for the 28F00AP30(1GBit) chip.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently it is possible to read and/or write to suspend EB's.
Writing /dev/mtdX or /dev/mtdblockX from several processes may
break the flash state machine.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Currently in ext4_valid_block_bitmap() we expect the bitmap to be
positioned anywhere between 0 and s_blocksize clusters, but that's
wrong because the bitmap can be placed anywhere in the block group. This
causes false positives when validating bitmaps on perfectly valid file
system layouts. Fix it by checking whether the bitmap is within the group
boundary.
The problem can be reproduced using the following
mkfs -t ext3 -E stride=256 /dev/vdb1
mount /dev/vdb1 /mnt/test
cd /mnt/test
wget https://cdn.kernel.org/pub/linux/kernel/v4.x/linux-4.16.3.tar.xz
tar xf linux-4.16.3.tar.xz
This will result in the warnings in the logs
EXT4-fs error (device vdb1): ext4_validate_block_bitmap:399: comm tar: bg 84: block 2774529: invalid block bitmap
[ Changed slightly for clarity and to not drop a overflow test -- TYT ]
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Reported-by: Ilya Dryomov <idryomov@gmail.com>
Fixes: 7dac4a1726 ("ext4: add validity checks for bitmap block numbers")
Cc: stable@vger.kernel.org
The current error handling for failed resource setup for xdp_ring
data is a break out of the loop and returning 0 indicated everything
was OK, when in fact it is not. Fix this by exiting via the
error exit label err_setup_tx that will clean up the resources
correctly and return and error status.
Detected by CoverityScan, CID#1466879 ("Logically dead code")
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Temporarily disable AES-GCM, as AES-CCM is only currently
enabled mechanism on client side. This fixes SMB3.11
encrypted mounts to Windows.
Also the tree connect request itself should be encrypted if
requested encryption ("seal" on mount), in addition we should be
enabling encryption in 3.11 based on whether we got any valid
encryption ciphers back in negprot (the corresponding session flag is
not set as it is in 3.0 and 3.02)
Signed-off-by: Steve French <smfrench@gmail.com>
Reviewed-by: Pavel Shilovsky <pshilov@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Stable <stable@vger.kernel.org>
Dan Carpenter had pointed this out a while ago, but the code around
this had changed so wasn't causing any problems since that field
was not used in this error path.
Still, it is cleaner to always initialize this field, so changing
the error path to set it.
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steve French <smfrench@gmail.com>
The same fix in Commit dbe173079a ("bridge: fix netconsole
setup over bridge") is also needed for team driver.
While at it, remove the unnecessary parameter *team from
team_port_enable_netpoll().
v1->v2:
- fix it in a better way, as does bridge.
Fixes: 0fb52a27a0 ("team: cleanup netpoll clode")
Reported-by: João Avelino Bellomo Filho <jbellomo@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OUI for TC Electronic is 0x000166, for TC GROUP A/S. 0x001486 is for Echo
Digital Audio Corporation.
Fixes: 7cafc65b3a ('ALSA: dice: force to add two pcm devices for listed models')
Cc: <stable@vger.kernel.org> # v4.6+
Reference: http://standards-oui.ieee.org/oui/oui.txt
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Dell Dock USB-audio device with 0bda:4014 is behaving notoriously
bad, and we have already applied some workaround to avoid the firmware
hiccup. Yet we still need to skip one thing, the Extension Unit at ID
4, which doesn't react correctly to the mixer ctl access.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1090658
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The UAC2 jack detection support introduced the bmControls checks in a
couple of places, but they forgot the endian conversion; the
bmControls of UAC2 terminal descriptor is __le16, not a byte like in
UAC1.
Fixes: 5a222e8494 ("ALSA: usb-audio: UAC2 jack detection")
Tested-by: Andrew Chant <achant@google.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules such as nouveau.ko and i915.ko have a link time dependency on
acpi_lid_open(), and due to its use of acpi_bus_register_driver(),
the button.ko module that provides it is only loadable when booted in
ACPI mode. However, the ACPI button driver can be built into the core
kernel as well, in which case the dependency can always be satisfied,
and the dependent modules can be loaded regardless of whether the
system was booted in ACPI mode or not.
So let's fix this asymmetry by making the ACPI button driver loadable
as a module even if not booted in ACPI mode, so it can provide the
acpi_lid_open() symbol in the same way as when built into the kernel.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
[ rjw: Minor adjustments of comments, whitespace and names. ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When CONFIG_MMU_NOTIFIER is not enabled, struct mmu_notifier has an
incomplete type definition, which causes build errors.
../drivers/gpu/drm/amd/amdkfd/kfd_priv.h:607:22: error: field 'mmu_notifier' has incomplete type
../include/linux/kernel.h:979:32: error: dereferencing pointer to incomplete type
../include/linux/kernel.h:980:18: error: dereferencing pointer to incomplete type
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:434:2: error: implicit declaration of function 'mmu_notifier_unregister_no_release' [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:435:2: error: implicit declaration of function 'mmu_notifier_call_srcu' [-Werror=implicit-function-declaration]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:438:21: error: variable 'kfd_process_mmu_notifier_ops' has initializer but incomplete type
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: error: unknown field 'release' specified in initializer
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: warning: excess elements in struct initializer [enabled by default]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:439:2: warning: (near initialization for 'kfd_process_mmu_notifier_ops') [enabled by default]
../drivers/gpu/drm/amd/amdkfd/kfd_process.c:534:2: error: implicit declaration of function 'mmu_notifier_register' [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
This debug code was helpful while developing the driver, but it isn't
being used for anything anymore.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently if a user requests clock counters for a node without a GPU
resource we will always return EINVAL.
Instead if no GPU resource is attached, fill the gpu_clock_counter
argument with zeroes so that we may proceed and return valid CPU
counters.
Signed-off-by: Andres Rodriguez <andres.rodriguez@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Passing NULL pointer to PTR_ERR will result in return value of 0
indicating success which is clearly not what it is intended here.
This patch returns -EINVAL instead.
v2: change ret code to -ENODEV
Fixes: 5ec7e02854 ("drm/amdkfd: Add ioctls for GPUVM memory management")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
WDAT table on Lenovo Z50-70 is using RTC SRAM (ports 0x70 and 0x71) to
store state of the timer. This conflicts with Linux RTC driver
(rtc-cmos.c) who fails to reserve those ports for itself preventing RTC
from functioning. In addition the WDAT table seems not to be fully
functional because it does not reset the system when the watchdog times
out.
On this system iTCO_wdt works just fine so we simply prefer to use it
instead of WDAT. This makes RTC working again and also results working
watchdog via iTCO_wdt.
Reported-by: Peter Milley <pbmilley@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199033
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If we go without an established session for a while, backoff delay will
climb to 30 seconds. The keepalive timeout is also 30 seconds, so it's
pretty easily hit after a prolonged hunting for a monitor: we don't get
a chance to send out a keepalive in time, which means we never get back
a keepalive ack in time, cutting an established session and attempting
to connect to a different monitor every 30 seconds:
[Sun Apr 1 23:37:05 2018] libceph: mon0 10.80.20.99:6789 session established
[Sun Apr 1 23:37:36 2018] libceph: mon0 10.80.20.99:6789 session lost, hunting for new mon
[Sun Apr 1 23:37:36 2018] libceph: mon2 10.80.20.103:6789 session established
[Sun Apr 1 23:38:07 2018] libceph: mon2 10.80.20.103:6789 session lost, hunting for new mon
[Sun Apr 1 23:38:07 2018] libceph: mon1 10.80.20.100:6789 session established
[Sun Apr 1 23:38:37 2018] libceph: mon1 10.80.20.100:6789 session lost, hunting for new mon
[Sun Apr 1 23:38:37 2018] libceph: mon2 10.80.20.103:6789 session established
[Sun Apr 1 23:39:08 2018] libceph: mon2 10.80.20.103:6789 session lost, hunting for new mon
The regular keepalive interval is 10 seconds. After ->hunting is
cleared in finish_hunting(), call __schedule_delayed() to ensure we
send out a keepalive after 10 seconds.
Cc: stable@vger.kernel.org # 4.7+
Link: http://tracker.ceph.com/issues/23537
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
This means that if we do some backoff, then authenticate, and are
healthy for an extended period of time, a subsequent failure won't
leave us starting our hunting sequence with a large backoff.
Mirrors ceph.git commit d466bc6e66abba9b464b0b69687cf45c9dccf383.
Cc: stable@vger.kernel.org # 4.7+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
The addr parameter isn't used for anything. Let's simplify and get rid of
it, like arm.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Vitezslav reported a case where the
"Timeout during microcode update!"
panic would hit. After a deeper look, it turned out that his .config had
CONFIG_HOTPLUG_CPU disabled which practically made save_mc_for_early() a
no-op.
When that happened, the discovered microcode patch wasn't saved into the
cache and the late loading path wouldn't find any.
This, then, lead to early exit from __reload_late() and thus CPUs waiting
until the timeout is reached, leading to the panic.
In hindsight, that function should have been written so it does not return
before the post-synchronization. Oh well, I know better now...
Fixes: bb8c13d61a ("x86/microcode: Fix CPU synchronization routine")
Reported-by: Vitezslav Samel <vitezslav@samel.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vitezslav Samel <vitezslav@samel.cz>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180418081140.GA2439@pc11.op.pod.cz
Link: https://lkml.kernel.org/r/20180421081930.15741-2-bp@alien8.de
save_mc_for_early() was a no-op on !CONFIG_HOTPLUG_CPU but the
generic_load_microcode() path saves the microcode patches it has found into
the cache of patches which is used for late loading too. Regardless of
whether CPU hotplug is used or not.
Make the saving unconditional so that late loading can find the proper
patch.
Reported-by: Vitezslav Samel <vitezslav@samel.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Vitezslav Samel <vitezslav@samel.cz>
Tested-by: Ashok Raj <ashok.raj@intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20180418081140.GA2439@pc11.op.pod.cz
Link: https://lkml.kernel.org/r/20180421081930.15741-1-bp@alien8.de
The current code extracts the physical address for UE errors and then
hooks it up into memory failure infrastructure. On successful
extraction of physical address it wrongly sets "handled = 1" which
means this UE error has been recovered. Since MCE handler gets return
value as handled = 1, it assumes that error has been recovered and
goes back to same NIP. This causes MCE interrupt again and again in a
loop leading to hard lockup.
Also, initialize phys_addr to ULONG_MAX so that we don't end up
queuing undesired page to hwpoison.
Without this patch we see:
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
...
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
Severe Machine check interrupt [Recovered]
NIP: [000000001002588c] PID: 7109 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffd2755940
Physical address: 000020181a080000
Memory failure: 0x20181a08: recovery action for dirty LRU page: Recovered
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
Memory failure: 0x20181a08: already hardware poisoned
...
Watchdog CPU:38 Hard LOCKUP
After this patch we see:
Severe Machine check interrupt [Not recovered]
NIP: [00007fffaae585f4] PID: 7168 Comm: find
Initiator: CPU
Error type: UE [Load/Store]
Effective address: 00007fffaafe28ac
Physical address: 00002017c0bd0000
find[7168]: unhandled signal 7 at 00007fffaae585f4 nip 00007fffaae585f4 lr 00007fffaae585e0 code 4
Memory failure: 0x2017c0bd: recovery action for dirty LRU page: Recovered
Fixes: 01eaac2b05 ("powerpc/mce: Hookup ierror (instruction) UE errors")
Fixes: ba41e1e1cc ("powerpc/mce: Hookup derror (load/store) UE errors")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
aTom Lendacky says:
====================
amd-xgbe: AMD XGBE driver fixes 2018-04-23
This patch series addresses some issues in the AMD XGBE driver.
The following fixes are included in this driver update series:
- Improve KR auto-negotiation and training (2 patches)
- Add pre and post auto-negotiation hooks
- Use the pre and post auto-negotiation hooks to disable CDR tracking
during auto-negotiation page exchange in KR mode
- Check for SFP tranceiver signal support and only use the signal if the
SFP indicates that it is supported
This patch series is based on net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The SFP eeprom indicates the transceiver signals (Rx LOS, Tx Fault, etc.)
that it supports. Update the driver to include checking the eeprom data
when deciding whether to use a transceiver signal.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update xgbe-phy-v2.c to make use of the auto-negotiation (AN) phy hooks
to improve the ability to successfully complete Clause 73 AN when running
at 10gbps. Hardware can sometimes have issues with CDR lock when the
AN DME page exchange is being performed.
The AN and KR training hooks are used as follows:
- The pre AN hook is used to disable CDR tracking in the PHY so that the
DME page exchange can be successfully and consistently completed.
- The post KR training hook is used to re-enable the CDR tracking so that
KR training can successfully complete.
- The post AN hook is used to check for an unsuccessful AN which will
increase a CDR tracking enablement delay (up to a maximum value).
Add two debugfs entries to allow control over use of the CDR tracking
workaround. The debugfs entries allow the CDR tracking workaround to
be disabled and determine whether to re-enable CDR tracking before or
after link training has been initiated.
Also, with these changes the receiver reset cycle that is performed during
the link status check can be performed less often.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add hooks to the driver auto-negotiation (AN) flow to allow the different
phy implementations to perform any steps necessary to improve AN.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We must validate sockaddr_len, otherwise userspace can pass fewer data
than we expect and we end up accessing invalid data.
Fixes: 224cf5ad14 ("ppp: Move the PPP drivers")
Reported-by: syzbot+4f03bdf92fdf9ef5ddab@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check sockaddr_len before dereferencing sp->sa_protocol, to ensure that
it actually points to valid data.
Fixes: fd558d186d ("l2tp: Split pppol2tp patch into separate l2tp and ppp parts")
Reported-by: syzbot+a70ac890b23b1bf29f5c@syzkaller.appspotmail.com
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If WOL event happened once, the LED[2] interrupt pin will not be
cleared unless we read the CSISR register. If interrupts are in use,
the normal interrupt handling will clear the WOL event. Let's clear the
WOL event before enabling it if !phy_interrupt_is_valid().
Signed-off-by: Jingju Hou <Jingju.Hou@synaptics.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NPU has a limited number of address translation shootdown (ATSD)
registers and the GPU has limited bandwidth to process ATSDs. This can
result in contention of ATSD registers leading to soft lockups on some
threads, particularly when invalidating a large address range in
pnv_npu2_mn_invalidate_range().
At some threshold it becomes more efficient to flush the entire GPU
TLB for the given MM context (PID) than individually flushing each
address in the range. This patch will result in ranges greater than
2MB being converted from 32+ ATSDs into a single ATSD which will flush
the TLB for the given PID on each GPU.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There is a single npu context per set of callback parameters. Callers
should be prevented from overwriting existing callback values so
instead return an error if different parameters are passed.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The pnv_npu2_init_context() and pnv_npu2_destroy_context() functions
are used to allocate/free contexts to allow address translation and
shootdown by the NPU on a particular GPU. Context initialisation is
implicitly safe as it is protected by the requirement mmap_sem be held
in write mode, however pnv_npu2_destroy_context() does not require
mmap_sem to be held and it is not safe to call with a concurrent
initialisation for a different GPU.
It was assumed the driver would ensure destruction was not called
concurrently with initialisation. However the driver may be simplified
by allowing concurrent initialisation and destruction for different
GPUs. As npu context creation/destruction is not a performance
critical path and the critical section is not large a single spinlock
is used for simplicity.
Fixes: 1ab66d1fba ("powerpc/powernv: Introduce address translation services for Nvlink2")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alistair Popple <alistair@popple.id.au>
Reviewed-by: Mark Hairgrove <mhairgrove@nvidia.com>
Tested-by: Mark Hairgrove <mhairgrove@nvidia.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Don't do this via custom code, instead now that we have support in the
arch hotplug/hotunplug code, rely on those routines to do the right
thing.
The existing flush doesn't work because it uses ppc64_caches.l1d.size
instead of ppc64_caches.l1d.line_size.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This patch adds support for flushing potentially dirty cache lines
when memory is hot-plugged/hot-un-plugged. The support is currently
limited to 64 bit systems.
The bug was exposed when mappings for a device were actually
hot-unplugged and plugged in back later. A similar issue was observed
during the development of memtrace, but memtrace does it's own
flushing of region via a custom routine.
These patches do a flush both on hotplug/unplug to clear any stale
data in the cache w.r.t mappings, there is a small race window where a
clean cache line may be created again just prior to tearing down the
mapping.
The patches were tested by disabling the flush routines in memtrace
and doing I/O on the trace file. The system immediately
checkstops (quite reliablly if prior to the hot-unplug of the memtrace
region, we memset the regions we are about to hot unplug). After these
patches no custom flushing is needed in the memtrace code.
Fixes: 9d5171a8f2 ("powerpc/powernv: Enable removal of memory for in memory tracing")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Balbir Singh <bsingharora@gmail.com>
Acked-by: Reza Arbab <arbab@linux.ibm.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The current mail address is rejected, last activity (with a different
address) in git-history is from 2012. Remove this.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a spelling error found in Kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix SIP conntrack with phones sending session descriptions for different
media types but same port numbers, from Florian Westphal.
2) Fix incorrect rtnl_lock mutex logic from IPVS sync thread, from Julian
Anastasov.
3) Skip compat array allocation in ebtables if there is no entries, also
from Florian.
4) Do not lose left/right bits when shifting marks from xt_connmark, from
Jack Ma.
5) Silence false positive memleak in conntrack extensions, from Cong Wang.
6) Fix CONFIG_NF_REJECT_IPV6=m link problems, from Arnd Bergmann.
7) Cannot kfree rule that is already in list in nf_tables, switch order
so this error handling is not required, from Florian Westphal.
8) Release set name in error path, from Florian.
9) include kmemleak.h in nf_conntrack_extend.c, from Stepheh Rothwell.
10) NAT chain and extensions depend on NF_TABLES.
11) Out of bound access when renaming chains, from Taehee Yoo.
12) Incorrect casting in xt_connmark leads to wrong bitshifting.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The current Cadence QSPI driver caused a kernel panic when loading
a Root Filesystem from QSPI. The problem was caused by reading more
bytes than needed because the QSPI operated on 4 bytes at a time.
<snip>
[ 7.947754] spi_nor_read[1048]:from 0x037cad74, len 1 [bfe07fff]
[ 7.956247] cqspi_read[910]:offset 0x58502516, buffer=bfe07fff
[ 7.956247]
[ 7.966046] Unable to handle kernel paging request at virtual
address bfe08002
[ 7.973239] pgd = eebfc000
[ 7.975931] [bfe08002] *pgd=2fffb811, *pte=00000000, *ppte=00000000
</snip>
Notice above how only 1 byte needed to be read but by reading 4 bytes
into the end of a mapped page, an unrecoverable page fault occurred.
This patch uses a temporary buffer to hold the 4 bytes read and then
copies only the bytes required into the buffer. A min() function is
used to limit the length to prevent buffer overflows.
Request testing of this patch on other platforms. This was tested
on the Intel Arria10 SoCFPGA DevKit.
Fixes: 0cf1725676 ("mtd: spi-nor: cqspi: Fix build on arches missing readsl/writesl")
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
We're missing a sentinel entry in kpti_safe_list. Thus is_midr_in_range_list()
can walk past the end of kpti_safe_list. Depending on the contents of memory,
this could erroneously match a CPU's MIDR, cause a data abort, or other bad
outcomes.
Add the sentinel entry to avoid this.
Fixes: be5b299830 ("arm64: capabilities: Add support for checks based on a list of MIDRs")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
KMSAN reported use of uninit-value that I tracked to lack
of proper size check on RTA_TABLE attribute.
I also believe RTA_PREFSRC lacks a similar check.
Fixes: 86872cb579 ("[IPv6] route: FIB6 configuration using struct fib6_config")
Fixes: c3968a857a ("ipv6: RTA_PREFSRC support for ipv6 route source address selection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Commit 8a8efa22f5 ("bonding: sync netpoll code with bridge"), it
would set slave_dev npinfo in slave_enable_netpoll when enslaving a dev
if bond->dev->npinfo was set.
However now slave_dev npinfo is set with bond->dev->npinfo before calling
slave_enable_netpoll. With slave_dev npinfo set, __netpoll_setup called
in slave_enable_netpoll will not call slave dev's .ndo_netpoll_setup().
It causes that the lower dev of this slave dev can't set its npinfo.
One way to reproduce it:
# modprobe bonding
# brctl addbr br0
# brctl addif br0 eth1
# ifconfig bond0 192.168.122.1/24 up
# ifenslave bond0 eth2
# systemctl restart netconsole
# ifenslave bond0 br0
# ifconfig eth2 down
# systemctl restart netconsole
The netpoll won't really work.
This patch is to remove that slave_dev npinfo setting in bond_enslave().
Fixes: 8a8efa22f5 ("bonding: sync netpoll code with bridge")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command 'perf record' calls:
cmd_report()
record__auxtrace_init()
auxtrace_record__init()
On s390 function auxtrace_record__init() returns random return value due
to missing initialization.
This sometime causes 'perf record' to exit immediately without error
message and creating a perf.data file.
Fix this by setting error the return code to zero before returning from
platform specific functions which may not set the error code in call
cases.
Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Link: http://lkml.kernel.org/r/20180423142940.21143-1-tmricht@linux.ibm.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Several options were incorrectly described, some lacked describing
required arguments while others were simply not documented, fix it.
Signed-off-by: Sangwon Hong <qpakzk@gmail.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Link: http://lkml.kernel.org/r/1524382146-19609-1-git-send-email-qpakzk@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
.. and other related fields that do not need to be enabled
for events that have sampling leader.
It fixes the perf top usage Ingo reported broken:
# perf top -e '{cycles,msr/aperf/}:S'
The 'msr/aperf/' event is configured for write_back sampling, which is
not allowed by the MSR PMU, so it fails to create the event.
Adjusting related attr test.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180423090823.32309-6-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The recent code refactoring made the argument for some helper
functions to be the explicit UAC_CS_* and UAC2_CS_* value instead of
0-based offset. However, there was one place left forgotten, and it
caused a regression on some devices appearing as the inconsistent
mixer setup.
This patch corrects the forgotten conversion.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199449
Fixes: 21e9b3e931 ("ALSA: usb-audio: fix uac control query argument")
Tested-by: Nazar Mokrynskyi <nazar@mokrynskyi.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
