Add ip tunnel dst cache in ip_md_tunnel_xmit to make more
efficient for the route lookup.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accept MSG_ZEROCOPY in all the TCP states that allow sendmsg. Remove
the explicit check for ESTABLISHED and CLOSE_WAIT states.
This requires correctly handling zerocopy state (uarg, sk_zckey) in
all paths reachable from other TCP states. Such as the EPIPE case
in sk_stream_wait_connect, which a sendmsg() in incorrect state will
now hit. Most paths are already safe.
Only extension needed is for TCP Fastopen active open. This can build
an skb with data in tcp_send_syn_data. Pass the uarg along with other
fastopen state, so that this skb also generates a zerocopy
notification on release.
Tested with active and passive tcp fastopen packetdrill scripts at
1747eef03d
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a refactoring patch: without changing runtime behavior,
it moves rbtree-related code from IPv4-specific files/functions
into .h/.c defrag files shared with IPv6 defragmentation code.
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aggregation effects are extremely common with wifi, cellular, and cable
modem link technologies, ACK decimation in middleboxes, and LRO and GRO
in receiving hosts. The aggregation can happen in either direction,
data or ACKs, but in either case the aggregation effect is visible
to the sender in the ACK stream.
Previously BBR's sending was often limited by cwnd under severe ACK
aggregation/decimation because BBR sized the cwnd at 2*BDP. If packets
were acked in bursts after long delays (e.g. one ACK acking 5*BDP after
5*RTT), BBR's sending was halted after sending 2*BDP over 2*RTT, leaving
the bottleneck idle for potentially long periods. Note that loss-based
congestion control does not have this issue because when facing
aggregation it continues increasing cwnd after bursts of ACKs, growing
cwnd until the buffer is full.
To achieve good throughput in the presence of aggregation effects, this
algorithm allows the BBR sender to put extra data in flight to keep the
bottleneck utilized during silences in the ACK stream that it has evidence
to suggest were caused by aggregation.
A summary of the algorithm: when a burst of packets are acked by a
stretched ACK or a burst of ACKs or both, BBR first estimates the expected
amount of data that should have been acked, based on its estimated
bandwidth. Then the surplus ("extra_acked") is recorded in a windowed-max
filter to estimate the recent level of observed ACK aggregation. Then cwnd
is increased by the ACK aggregation estimate. The larger cwnd avoids BBR
being cwnd-limited in the face of ACK silences that recent history suggests
were caused by aggregation. As a sanity check, the ACK aggregation degree
is upper-bounded by the cwnd (at the time of measurement) and a global max
of BW * 100ms. The algorithm is further described by the following
presentation:
https://datatracker.ietf.org/meeting/101/materials/slides-101-iccrg-an-update-on-bbr-work-at-google-00
In our internal testing, we observed a significant increase in BBR
throughput (measured using netperf), in a basic wifi setup.
- Host1 (sender on ethernet) -> AP -> Host2 (receiver on wifi)
- 2.4 GHz -> BBR before: ~73 Mbps; BBR after: ~102 Mbps; CUBIC: ~100 Mbps
- 5.0 GHz -> BBR before: ~362 Mbps; BBR after: ~593 Mbps; CUBIC: ~601 Mbps
Also, this code is running globally on YouTube TCP connections and produced
significant bandwidth increases for YouTube traffic.
This is based on Ian Swett's max_ack_height_ algorithm from the
QUIC BBR implementation.
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because bbr_target_cwnd() is really a general-purpose BBR helper for
computing some volume of inflight data as a function of the estimated
BDP, refactor it into following helper functions:
- bbr_bdp()
- bbr_quantization_budget()
- bbr_inflight()
Signed-off-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the internal use of the skb_trimmed is reduced to
the ICMPv6/IGMP checksum verification. And for the length checks
the newly introduced helper functions are used instead of calculating
and checking with skb->len directly.
These changes should hopefully make it easier to verify that length
checks are performed properly.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been many people complaining about the inconsistent
behaviors of IPv4 and IPv6 devconf when creating new network
namespaces. Currently, for IPv4, we inherit all current settings
from init_net, but for IPv6 we reset all setting to default.
This patch introduces a new /proc file
/proc/sys/net/core/devconf_inherit_init_net to control the
behavior of whether to inhert sysctl current settings from init_net.
This file itself is only available in init_net.
As demonstrated below:
Initial setup in init_net:
# cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# cat /proc/sys/net/ipv6/conf/all/accept_dad
1
Default value 0 (current behavior):
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
0
Set to 1 (inherit from init_net):
# echo 1 > /proc/sys/net/core/devconf_inherit_init_net
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
2
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
1
Set to 2 (reset to default):
# echo 2 > /proc/sys/net/core/devconf_inherit_init_net
# ip netns del test
# ip netns add test
# ip netns exec test cat /proc/sys/net/ipv4/conf/all/rp_filter
0
# ip netns exec test cat /proc/sys/net/ipv6/conf/all/accept_dad
0
Set to a value out of range (invalid):
# echo 3 > /proc/sys/net/core/devconf_inherit_init_net
-bash: echo: write error: Invalid argument
# echo -1 > /proc/sys/net/core/devconf_inherit_init_net
-bash: echo: write error: Invalid argument
Reported-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Reported-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
v2: - improve extack messages (DaveA).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
v2: - new patch (DaveA).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have these fields cleared, then a clone
will also inherit zero values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have proper tp->rack value,
then a clone will also inherit proper initial value.
Note that fresh sockets init tp->rack from tcp_init_sock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have app_limited set to ~0U,
then a clone will also inherit proper initial value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure all listeners have these fields cleared, then a clone
will also inherit zero values.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All listeners have this field cleared already, since tcp_disconnect()
clears it and newly created sockets have also a zero value here.
So a clone will inherit a zero value here.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Passive connections can inherit proper value by cloning,
if we make sure all listeners have the proper values there.
tcp_disconnect() was setting snd_cwnd to 2, which seems
quite obsolete since IW10 adoption.
Also remove an obsolete comment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure a listener always has its mdev_us
field set to TCP_TIMEOUT_INIT, we do not need to rewrite
this field after a new clone is created.
tcp_disconnect() is very seldom used in real applications.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All listeners have this field cleared already, since tcp_disconnect()
clears it and newly created sockets have also a zero value here.
So a clone will inherit a zero value here.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sockets have this field cleared, and tcp_disconnect()
calls tcp_write_queue_purge() which among other things
also clear tp->packets_out
So a listener is guaranteed to have this field cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we make sure a listener always has its icsk_rto
field set to TCP_TIMEOUT_INIT, we do not need to rewrite
this field after a new clone is created.
tcp_disconnect() is very seldom used in real applications.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New sockets get the field set to TCP_INFINITE_SSTHRESH in tcp_init_sock()
In case a socket had this field changed and transitions to TCP_LISTEN
state, tcp_disconnect() also makes sure snd_ssthresh is set to
TCP_INFINITE_SSTHRESH.
So a listener has this field set to TCP_INFINITE_SSTHRESH already.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when the sender fails to send (original) data packet or
window probes due to congestion in the local host (e.g. throttling
in qdisc), it'll retry within an RTO or two up to 500ms.
In low-RTT networks such as data-centers, RTO is often far below
the default minimum 200ms. Then local host congestion could trigger
a retry storm pouring gas to the fire. Worse yet, the probe counter
(icsk_probes_out) is not properly updated so the aggressive retry
may exceed the system limit (15 rounds) until the packet finally
slips through.
On such rare events, it's wise to retry more conservatively
(500ms) and update the stats properly to reflect these incidents
and follow the system limit. Note that this is consistent with
the behaviors when a keep-alive probe or RTO retry is dropped
due to local congestion.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when the sender fails to retransmit a data packet on
timeout due to congestion in the local host (e.g. throttling in
qdisc), it'll retry within an RTO up to 500ms.
In low-RTT networks such as data-centers, RTO is often far
below the default minimum 200ms (and the cap 500ms). Then local
host congestion could trigger a retry storm pouring gas to the
fire. Worse yet, the retry counter (icsk_retransmits) is not
properly updated so the aggressive retry may exceed the system
limit (15 rounds) until the packet finally slips through.
On such rare events, it's wise to retry more conservatively (500ms)
and update the stats properly to reflect these incidents and follow
the system limit. Note that this is consistent with the behavior
when a keep-alive probe is dropped due to local congestion.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we use the next unsent skb's timestamp to determine
when to abort a socket stalling on window probes. This no longer
works as skb timestamp reflects the last instead of the first
transmission.
Instead we can estimate how long the socket has been stalling
with the probe count and the exponential backoff behavior.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper to model TCP exponential backoff for the next patch.
This is pure refactor w no behavior change.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses a corner issue on timeout behavior of a
passive Fast Open socket. A passive Fast Open server may write
and close the socket when it is re-trying SYN-ACK to complete
the handshake. After the handshake is completely, the server does
not properly stamp the recovery start time (tp->retrans_stamp is
0), and the socket may abort immediately on the very first FIN
timeout, instead of retying until it passes the system or user
specified limit.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP socket's retrans_stamp is not set if the
retransmission has failed to send. As a result if a socket is
experiencing local issues to retransmit packets, determining when
to abort a socket is complicated w/o knowning the starting time of
the recovery since retrans_stamp may remain zero.
This complication causes sub-optimal behavior that TCP may use the
latest, instead of the first, retransmission time to compute the
elapsed time of a stalling connection due to local issues. Then TCP
may disrecard TCP retries settings and keep retrying until it finally
succeed: not a good idea when the local host is already strained.
The simple fix is to always timestamp the start of a recovery.
It's worth noting that retrans_stamp is also used to compare echo
timestamp values to detect spurious recovery. This patch does
not break that because retrans_stamp is still later than when the
original packet was sent.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP skbs are not always timestamped if the transmission
failed due to memory or other local issues. This makes deciding
when to abort a socket tricky and complicated because the first
unacknowledged skb's timestamp may be 0 on TCP timeout.
The straight-forward fix is to always timestamp skb on every
transmission attempt. Also every skb retransmission needs to be
flagged properly to avoid RTT under-estimation. This can happen
upon receiving an ACK for the original packet and the a previous
(spurious) retransmission has failed.
It's worth noting that this reverts to the old time-stamping
style before commit 8c72c65b42 ("tcp: update skb->skb_mstamp more
carefully") which addresses a problem in computing the elapsed time
of a stalled window-probing socket. The problem will be addressed
differently in the next patches with a simpler approach.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously TCP only warns if its RTO timer fires and the
retransmission queue is empty, but it'll cause null pointer
reference later on. It's better to avoid such catastrophic failure
and simply exit with a warning.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4cdeeee925 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.
The issue was found with LTP/network tests (UDP-Lite test-cases).
Fixes: 4cdeeee925 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udp-tunnel setup allows binding sockets to a network device. Prefer
the new SO_BINDTOIFINDEX to avoid temporarily resolving the device-name
just to look it up in the ioctl again.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said in draft-foschiano-erspan-03#section4:
Different frame variants known as "ERSPAN Types" can be
distinguished based on the GRE "Protocol Type" field value: Type I
and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].
So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of
the connection and so transitions this socket to CLOSE_WAIT state.
Transmission in close wait state is acceptable. Other similar tests in
the stack (e.g., in FastOpen) accept both states. Relax this test, too.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Yuchung Cheng <ycheng@google.com>
CC: Neal Cardwell <ncardwell@google.com>
CC: Soheil Hassas Yeganeh <soheil@google.com>
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 routing tables are flushed in two cases:
1. In response to events in the netdev and inetaddr notification chains
2. When a network namespace is being dismantled
In both cases only routes associated with a dead nexthop group are
flushed. However, a nexthop group will only be marked as dead in case it
is populated with actual nexthops using a nexthop device. This is not
the case when the route in question is an error route (e.g.,
'blackhole', 'unreachable').
Therefore, when a network namespace is being dismantled such routes are
not flushed and leaked [1].
To reproduce:
# ip netns add blue
# ip -n blue route add unreachable 192.0.2.0/24
# ip netns del blue
Fix this by not skipping error routes that are not marked with
RTNH_F_DEAD when flushing the routing tables.
To prevent the flushing of such routes in case #1, add a parameter to
fib_table_flush() that indicates if the table is flushed as part of
namespace dismantle or not.
Note that this problem does not exist in IPv6 since error routes are
associated with the loopback device.
[1]
unreferenced object 0xffff888066650338 (size 56):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 b0 1c 62 61 80 88 ff ff ..........ba....
e8 8b a1 64 80 88 ff ff 00 07 00 08 fe 00 00 00 ...d............
backtrace:
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
unreferenced object 0xffff888061621c88 (size 48):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
6b 6b 6b 6b 6b 6b 6b 6b d8 8e 26 5f 80 88 ff ff kkkkkkkk..&_....
backtrace:
[<00000000733609e3>] fib_table_insert+0x978/0x1500
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
Fixes: 8cced9eff1 ("[NETNS]: Enable routing configuration in non-initial namespace.")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpfilter_umh will be stopped via __stop_umh() when the bpfilter
error occurred.
The bpfilter_umh() couldn't start again because there is no restart
routine.
The section of the bpfilter_umh_{start/end} is no longer .init.rodata
because these area should be reused in the restart routine. hence
the section name is changed to .bpfilter_umh.
The bpfilter_ops->start() is restart callback. it will be called when
bpfilter_umh is stopped.
The stop bit means bpfilter_umh is stopped. this bit is set by both
start and stop routine.
Before this patch,
Test commands:
$ iptables -vnL
$ kill -9 <pid of bpfilter_umh>
$ iptables -vnL
[ 480.045136] bpfilter: write fail -32
$ iptables -vnL
All iptables commands will fail.
After this patch,
Test commands:
$ iptables -vnL
$ kill -9 <pid of bpfilter_umh>
$ iptables -vnL
$ iptables -vnL
Now, all iptables commands will work.
Fixes: d2ba09c17a ("net: add skeleton of bpfilter kernel module")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, UMH process is killed, do_exit() calls the umh_info->cleanup callback
to release members of the umh_info.
This patch makes bpfilter_umh's cleanup routine to use the
umh_info->cleanup callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously upon SYN timeouts the sender recomputes the txhash to
try a different path. However this does not apply on the initial
timeout of SYN-data (active Fast Open). Therefore an active IPv6
Fast Open connection may incur one second RTO penalty to take on
a new path after the second SYN retransmission uses a new flow label.
This patch removes this undesirable behavior so Fast Open changes
the flow label just like the regular connections. This also helps
avoid falsely disabling Fast Open on the sender which triggers
after two consecutive SYN timeouts on Fast Open.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2efd4fca70 ("ip: in cmsg IP(V6)_ORIGDSTADDR call
pskb_may_pull") avoided a read beyond the end of the skb linear
segment by calling pskb_may_pull.
That function can trigger a BUG_ON in pskb_expand_head if the skb is
shared, which it is when when peeking. It can also return ENOMEM.
Avoid both by switching to safer skb_header_pointer.
Fixes: 2efd4fca70 ("ip: in cmsg IP(V6)_ORIGDSTADDR call pskb_may_pull")
Reported-by: syzbot <syzkaller@googlegroups.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 11789039da ("fou: Prevent unbounded recursion in GUE error
handler"), I didn't take care of the case where UDP-Lite is encapsulated
into UDP or UDP-Lite with GUE. From a syzbot report about a possibly
similar issue with GUE on IPv6, I just realised the same thing might
happen with a UDP-Lite inner payload.
Also skip exception handling for inner UDP-Lite protocol.
Fixes: 11789039da ("fou: Prevent unbounded recursion in GUE error handler")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes a regression in AF_INET/RTM_GETADDR and
AF_INET6/RTM_GETADDR.
Before this commit, the kernel would stop dumping addresses once the first
skb was full and end the stream with NLMSG_DONE(-EMSGSIZE). The error
shouldn't be sent back to netlink_dump so the callback is kept alive. The
userspace is expected to call back with a new empty skb.
Changes from V1:
- The error is not handled in netlink_dump anymore but rather in
inet_dump_ifaddr and inet6_dump_addr directly as suggested by
David Ahern.
Fixes: d7e38611b8 ("net/ipv4: Put target net when address dump fails due to bad attributes")
Fixes: 242afaa696 ("net/ipv6: Put target net when address dump fails due to bad attributes")
Cc: David Ahern <dsahern@gmail.com>
Cc: "David S . Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: Arthur Gautier <baloo@gandi.net>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Several fixes here. Basically split down the line between newly
introduced regressions and long existing problems:
1) Double free in tipc_enable_bearer(), from Cong Wang.
2) Many fixes to nf_conncount, from Florian Westphal.
3) op->get_regs_len() can throw an error, check it, from Yunsheng
Lin.
4) Need to use GFP_ATOMIC in *_add_hash_mac_address() of fsl/fman
driver, from Scott Wood.
5) Inifnite loop in fib_empty_table(), from Yue Haibing.
6) Use after free in ax25_fillin_cb(), from Cong Wang.
7) Fix socket locking in nr_find_socket(), also from Cong Wang.
8) Fix WoL wakeup enable in r8169, from Heiner Kallweit.
9) On 32-bit sock->sk_stamp is not thread-safe, from Deepa Dinamani.
10) Fix ptr_ring wrap during queue swap, from Cong Wang.
11) Missing shutdown callback in hinic driver, from Xue Chaojing.
12) Need to return NULL on error from ip6_neigh_lookup(), from Stefano
Brivio.
13) BPF out of bounds speculation fixes from Daniel Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
ipv6: Consider sk_bound_dev_if when binding a socket to an address
ipv6: Fix dump of specific table with strict checking
bpf: add various test cases to selftests
bpf: prevent out of bounds speculation on pointer arithmetic
bpf: fix check_map_access smin_value test when pointer contains offset
bpf: restrict unknown scalars of mixed signed bounds for unprivileged
bpf: restrict stack pointer arithmetic for unprivileged
bpf: restrict map value pointer arithmetic for unprivileged
bpf: enable access to ax register also from verifier rewrite
bpf: move tmp variable into ax register in interpreter
bpf: move {prev_,}insn_idx into verifier env
isdn: fix kernel-infoleak in capi_unlocked_ioctl
ipv6: route: Fix return value of ip6_neigh_lookup() on neigh_create() error
net/hamradio/6pack: use mod_timer() to rearm timers
net-next/hinic:add shutdown callback
net: hns3: call hns3_nic_net_open() while doing HNAE3_UP_CLIENT
ip: validate header length on virtual device xmit
tap: call skb_probe_transport_header after setting skb->dev
ptr_ring: wrap back ->producer in __ptr_ring_swap_queue()
net: rds: remove unnecessary NULL check
...
KMSAN detected read beyond end of buffer in vti and sit devices when
passing truncated packets with PF_PACKET. The issue affects additional
ip tunnel devices.
Extend commit 76c0ddd8c3 ("ip6_tunnel: be careful when accessing the
inner header") and commit ccfec9e5cb ("ip_tunnel: be careful when
accessing the inner header").
Move the check to a separate helper and call at the start of each
ndo_start_xmit function in net/ipv4 and net/ipv6.
Minor changes:
- convert dev_kfree_skb to kfree_skb on error path,
as dev_kfree_skb calls consume_skb which is not for error paths.
- use pskb_network_may_pull even though that is pedantic here,
as the same as pskb_may_pull for devices without llheaders.
- do not cache ipv6 hdrs if used only once
(unsafe across pskb_may_pull, was more relevant to earlier patch)
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warn this:
net/ipv4/fib_rules.c:203 fib_empty_table() warn:
always true condition '(id <= 4294967295) => (0-u32max <= u32max)'
'id' is u32, which always not greater than RT_TABLE_MAX
(0xFFFFFFFF), So add a check to break while wrap around.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
totalram_pages and totalhigh_pages are made static inline function.
Main motivation was that managed_page_count_lock handling was complicating
things. It was discussed in length here,
https://lore.kernel.org/patchwork/patch/995739/#1181785 So it seemes
better to remove the lock and convert variables to atomic, with preventing
poteintial store-to-read tearing as a bonus.
[akpm@linux-foundation.org: coding style fixes]
Link: http://lkml.kernel.org/r/1542090790-21750-4-git-send-email-arunks@codeaurora.org
Signed-off-by: Arun KS <arunks@codeaurora.org>
Suggested-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Reviewed-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reviewed-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
