Fix IP Reset processing - wait for RDY before proceeding
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix quarantined XRI recovery qualifier state in link bounce
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix discovery timeout during nameserver login
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: Dick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In prandom we have already reseeding mechanisms that trigger
periodically from a much better entropy source than just
feeding in jiffies through lpfc_mbx_cmpl_fcf_scan_read_fcf_rec()
[what a function name 8-)]. Therefore, just remove this.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
To be future-proof and for better readability the time comparisons
are modified to use time_after() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[PATCH 26/55] scsi: Mark function as static in lpfc/lpfc_bsg.c
Mark function as static in lpfc/lpfc_bsg.c because it is not used
outside this file.
This eliminates the following warning in lpfc/lpfc_bsg.c:
drivers/scsi/lpfc/lpfc_bsg.c:3348:1: warning: no previous prototype for ‘lpfc_bsg_issue_mbox_cmpl’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark functions as static in lpfc/lpfc_scsi.c because they are not used
outside this file.
This eliminates the following warnings in lpfc/lpfc_scsi.c:
drivers/scsi/lpfc/lpfc_scsi.c:299:1: warning: no previous prototype for ‘lpfc_change_queue_depth’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:795:1: warning: no previous prototype for ‘lpfc_sli4_post_scsi_sgl_list’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:3019:1: warning: no previous prototype for ‘lpfc_bg_crc’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:3035:1: warning: no previous prototype for ‘lpfc_bg_csum’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:3048:1: warning: no previous prototype for ‘lpfc_calc_bg_err’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark functions as static in lpfc/lpfc_init.c because they are not used
outside this file.
This eliminates the following warning in lpfc/lpfc_init.c:
drivers/scsi/lpfc/lpfc_init.c:652:1: warning: no previous prototype for ‘lpfc_hba_init_link’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_init.c:753:1: warning: no previous prototype for ‘lpfc_hba_down_link’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_init.c:3434:1: warning: no previous prototype for ‘lpfc_sli4_fcf_redisc_wait_tmo’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Mark functions as static in lpfc/lpfc_hbadisc.c because they are not
used outside this file.
This eliminates the following warnings in lpfc/lpfc_hbadisc.c:
drivers/scsi/lpfc/lpfc_hbadisc.c:2047:5: warning: no previous prototype for ‘lpfc_sli4_fcf_pri_list_add’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_hbadisc.c:2681:1: warning: no previous prototype for ‘lpfc_init_vfi_cmpl’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_hbadisc.c:4432:1: warning: no previous prototype for ‘lpfc_nlp_logo_unreg’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[PATCH 22/55] scsi: Mark functions as static in lpfc/lpfc_sli.c
Mark functions as static in lpfc/lpfc_sli.c because they are not used
outside this file.
This eliminates the following warnings in lpfc/lpfc_sli.c:
drivers/scsi/lpfc/lpfc_sli.c:13867:1: warning: no previous prototype for ‘lpfc_sli4_alloc_xri’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:13897:1: warning: no previous prototype for ‘__lpfc_sli4_free_xri’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:14317:1: warning: no previous prototype for ‘lpfc_update_rcv_time_stamp’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:14786:1: warning: no previous prototype for ‘lpfc_sli4_handle_unsol_abort’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:15331:1: warning: no previous prototype for ‘__lpfc_sli4_free_rpi’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:15769:1: warning: no previous prototype for ‘lpfc_check_next_fcf_pri_level’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:16000:1: warning: no previous prototype for ‘lpfc_mbx_cmpl_redisc_fcf_table’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
1) Assgning FIP_ALL_FCF_MACS to fcoe_all_fcfs allows VLAN request to be sent
to correct Mac address for VLAN Discovery otherwise VLAN request will be
sent to invalid address hence FLOGI never happens.
2) Simplify the copy_and_format_trace_data code and log the correct Link event
for fnic control path tracing in case of link status UP->UP.
3) Increment Fnic driver version
Signed-off-by: Hiral Shah <hishah@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The PCI register read checking introduced in commit fe1b806f4f
("qla2xxx: Disable adapter when we encounter a PCI disconnect") is
active during driver probe. Hold off scheduling any board removal until
the driver probe has completed. This ensures that the the board_disable
work structure is initialized and more importantly, avoids racing
qla2x00_probe_one.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduce mutual exclusion between the qla2xxx_remove_one PCI driver
callback and qla2x00_disable_board_on_pci_error, which is scheduled as
board_disable work by qla2x00_check_reg{32,16}_for_disconnect:
* Leave the driver-specific data attached to the underlying PCI device
intact in qla2x00_disable_board_on_pci_error, so that qla2x00_remove_one
has enough breadcrumbs to determine that any board_disable work has been
completed.
* In qla2xxx_remove_one, set a bit to prevent any subsequent
board_disable work from scheduling, then cancel and wait until pending
work has completed.
* Reuse the PCI device enable count check in qla2x00_remove_one to
determine if board_disable has occured. The original purpose of this
check was unnecessary since the driver remove function wasn't called
when the probe fails.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There are various callers of qla2x00_check_reg{32,16}_for_disconnect
that may schedule board removal on PCI-disconnect. Test-and-set a
dedicated flag before scheduling board_disable so it is invoked only
once.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add an uint16_t variant of qla2x00_check_reg_for_disconnect and use
these routines to check and schedule a PCI-disconnected board from a
centralized place.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Take advantage of commit fe1b806f4f ("qla2xxx: Refactor shutdown code
so some functionality can be reused") to remove an inlined copy of
qla2x00_clear_drv_active in the driver's probe hardware error path.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Once calling scsi_host_put, be careful to not access qla_hw_data through
the Scsi_Host private data (ie, scsi_qla_host base_vha).
Fixes: fe1b806f4f ("qla2xxx: Refactor shutdown code so some functionality can be reused")
Cc: stable@vger.kernel.org # 3.14, 3.15, 3.16
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas updates the driver version and
Documentation/scsi/ChangeLog.megaraid_sas.
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas fixes a reset_mutex leak in megasas_reset_fusion().
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas removes some unused variables from the megasas_instance structure.
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas adds a missing initial call to
megasas_get_ld_vf_affiliation() at the end of megasas_probe_one().
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The following patch for megaraid_sas fixes the LD/VF affiliation policy parsing
code to account for LD targetId's and Hidden LD's (not yet affiliated with any
Virtual Functions). This also breaks megasas_get_ld_vf_affiliation() into 2
separate functions: megasas_get_ld_vf_affiliation_111() and
megasas_get_ld_Vf_affiliation_12() to reduce indentation levels.
Signed-off-by: Adam Radford <aradford@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Since a lot of functionality from SPC-4 is supported by this
driver (e.g. LBP and PI) then bump the default INQUIRY version
from SPC-3 to SPC-4. Also update the INQUIRY version
descriptors.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Give existing errors priority over the generation of Task
Set Full (TSF) errors. So that max_queue is not exceeded,
existing errors may be sent back in the invocation thread.
This is done so errors like Unit Attentions are not hidden
and lost by either max_queue exceeded or real/injected
TSFs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch removes a NULL check for the scsi_cmnd::cmnd pointer
since many other instances in this driver and elsewhere assume
it is valid. Also redundant casts to 'unsigned char *' are removed
as the pointer has that type.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a second(kdump) kernel starts and the hard reset method is used
the driver calls pci_disable_device without previously enabling it,
so the kernel shows a warning -
[ 16.876248] WARNING: at drivers/pci/pci.c:1431 pci_disable_device+0x84/0x90()
[ 16.882686] Device hpsa
disabling already-disabled device
...
This patch fixes it, in addition to this I tried to balance also some other pairs
of enable/disable device in the driver.
Unfortunately I wasn't able to verify the functionality for the case of a sw reset,
because of a lack of proper hw.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of using the virt_ptr use request buffer for copying
back the nvmd response data and use the same in request function also
Signed-off-by: Suresh Thiagarajan <suresh.thiagarajan@pmcs.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Bump the driver version
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Driver should process the completion queue entries before a connection
resources are freed. While running mixed traffic due to latency, driver
processes the CQE after the connection resources are freed. This fix
processes all the completion queue before the connection resources are
freed.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
During port async event driver should check if there is any boot target
configured on the adapter. Update sysfs enteries with the boot target
parameters.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Change the copyright year to 2014
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Limiting which port update events will allow the driver to kick off a
name server scan has been problematic in some corner cases so remove the
restriction and restore the previous semantic. Also move the link
up/down informational messages to the LOOP_UP and LOOP_DOWN events.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Move the mailbox failure messages to a default debugging level so that
benign failures won't flood the system logs but will still show up if
default debug messaging is enabled (ql2xextended_error_logging=1).
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Log message code 0x00c6 preserved, although it is reported
after successful call to pci_enable_msix_range(), not before
possibly unsuccessful call to pci_enable_msix(). Consumers
of the error code should not notice the difference.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: qla2xxx-upstream@qlogic.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Kashyap Desai <Kashyap.desai@avagotech.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the driver fails to analize MSI-X re-enablement
status on resuming and always assumes the success. This
update checks the MSI-X initialization result and fails
to resume if MSI-Xs re-enablement failed.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Kashyap Desai <Kashyap.desai@avagotech.com>
Cc: Neela Syam Kolli <megaraidlinux@lsi.com>
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Cc: iss_storagedev@hp.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently the driver falls back to INTx mode when MSI-X
initialization failed. This is a suboptimal behaviour
for chips that also support MSI. This update changes that
behaviour and falls back to MSI mode in case MSI-X mode
initialization failed.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Cc: iss_storagedev@hp.com
Cc: linux-scsi@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
port_detect is only called from the module_init routine and thus implicitly
serialized, so remove the driver lock which was held over potentially
sleeping function calls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Fix build errors when CONFIG_SCSI_NETLINK is enabled but
CONFIG_NET is not enabled:
drivers/built-in.o: In function `scsi_nl_rcv_msg':
scsi_netlink.c:(.text+0x1850fa): undefined reference to `netlink_ack'
scsi_netlink.c:(.text+0x185105): undefined reference to `skb_pull'
scsi_netlink.c:(.text+0x18515d): undefined reference to `netlink_capable'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185244): undefined reference to `init_net'
drivers/built-in.o: In function `scsi_netlink_init':
(.text+0x185258): undefined reference to `__netlink_kernel_create'
drivers/built-in.o: In function `scsi_netlink_exit':
(.text+0x185291): undefined reference to `netlink_kernel_release'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SCSI Well-known logical units generally don't have any scsi driver
associated with it which means no one will call scsi_autopm_put_device()
on these wlun scsi devices and this would result in keeping the
corresponding scsi device always active (hence LLD can't be suspended as
well). Same exact problem can be seen for other scsi device representing
normal logical unit whose driver is yet to be loaded. This patch fixes
the above problem with this approach:
- make the scsi_autopm_put_device call at the end of scsi_sysfs_add_sdev
to make it balance out the get earlier in the function.
- let drivers do paired get/put calls in their probe methods.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI specification requires that the second Command Data Byte
should contain the LUN value in its high-order bits if the recipient
device reports SCSI level 2 or below. Nevertheless, some USB
mass-storage devices use those bits for other purposes in
vendor-specific commands. Currently Linux has no way to send such
commands, because the SCSI stack always overwrites the LUN bits.
Testing shows that Windows 7 and XP do not store the LUN bits in the
CDB when sending commands to a USB device. This doesn't matter if the
device uses the Bulk-Only or UAS transports (which virtually all
modern USB mass-storage devices do), as these have a separate
mechanism for sending the LUN value.
Therefore this patch introduces a flag in the Scsi_Host structure to
inform the SCSI midlayer that a transport does not require the LUN
bits to be stored in the CDB, and it makes usb-storage set this flag
for all devices using the Bulk-Only transport. (UAS is handled by a
separate driver, but it doesn't really matter because no SCSI-2 or
lower device is at all likely to use UAS.)
The patch also cleans up the code responsible for storing the LUN
value by adding a bitflag to the scsi_device structure. The test for
whether to stick the LUN value in the CDB can be made when the device
is probed, and stored for future use rather than being made over and
over in the fast path.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Tiziano Bacocco <tiziano.bacocco@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a use_cmd_list flag in struct Scsi_Host to request keeping track of
all outstanding commands per device.
Default behaviour is not to keep track of cmd_list per sdev, as this may
introduce lock contention. (overhead is more on multi-node NUMA.), and
only enable it on the two drivers that need it.
Signed-off-by: Kashyap Desai <kashyap.desai@avagotech.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SYNCHRONIZE_CACHE command is a medium write command and hence can
fail when the device is write protected. Avoid sending such commands by
making sure that write-cache-enable is disabled even though the device
claim to support it.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Convert spaces to tabs in kernel-doc notation.
Correct duplicated (copy-paste) kernel-doc comments that are incorrect.
Fix kernel-doc warning:
Warning(..//drivers/scsi/scsi_error.c:1647): No description found for parameter 'shost'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Just like CNIC, tristate of these two modules is also dependent on IPV6.
These need to be handled separately as they select CNIC, which can override
tristate for CNIC from 'm' to 'y', which can cause build failures when ipv6 is
compiled as a module even if CNIC's Kconfig will only 'm' or 'n' when ipv6 is
compiled as a module.
Fixes: c99d667e85 ("cnic : Cleanup CONFIG_IPV6 & VLAN check")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Required for avoiding recursive dependencies in the Kconfig, brought out
by fixing randconfig error for bnx2i/bnx2fc in the patch that follows.
As suggested by Randy Dunlap
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu.
This function is used by iscsi drivers and userspace to send iscsi PDUs/
commands. For login commands, we have a set buffer size. For all other
commands we do not support data buffers.
This was reported by Dan Carpenter here:
http://www.spinics.net/lists/linux-scsi/msg66838.html
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A bit of churn on the for-linus side that would be nice to have
in the core bits for 3.18, so pull it in to catch us up and make
forward progress easier.
Signed-off-by: Jens Axboe <axboe@fb.com>
Conflicts:
block/scsi_ioctl.c
Pull block layer fixes from Jens Axboe:
"A smaller collection of fixes that have come up since the initial
merge window pull request. This contains:
- error handling cleanup and support for larger than 16 byte cdbs in
sg_io() from Christoph. The latter just matches what bsg and
friends support, sg_io() got left out in the merge.
- an option for brd to expose partitions in /proc/partitions. They
are hidden by default for compat reasons. From Dmitry Monakhov.
- a few blk-mq fixes from me - killing a dead/unused flag, fix for
merging happening even if turned off, and correction of a few
comments.
- removal of unnecessary ->owner setting in systemace. From Michal
Simek.
- two related fixes for a problem with nesting freezing of queues in
blk-mq. One from Ming Lei removing an unecessary freeze operation,
and another from Tejun fixing the nesting regression introduced in
the merge window.
- fix for a BUG_ON() at bio_endio time when protection info is
attached and the IO has an error. From Sagi Grimberg.
- two scsi_ioctl bug fixes for regressions with scsi-mq from Tony
Battersby.
- a cfq weight update fix and subsequent comment update from Toshiaki
Makita"
* 'for-linus' of git://git.kernel.dk/linux-block:
cfq-iosched: Add comments on update timing of weight
cfq-iosched: Fix wrong children_weight calculation
block: fix error handling in sg_io
fix regression in SCSI_IOCTL_SEND_COMMAND
scsi-mq: fix requests that use a separate CDB buffer
block: support > 16 byte CDBs for SG_IO
block: cleanup error handling in sg_io
brd: add ram disk visibility option
block: systemace: Remove .owner field for driver
blk-mq: blk_mq_freeze_queue() should allow nesting
blk-mq: correct a few wrong/bad comments
block: Fix BUG_ON when pi errors occur
blk-mq: don't allow merges if turned off for the queue
blk-mq: get rid of unused BLK_MQ_F_SHOULD_SORT flag
blk-mq: fix WARNING "percpu_ref_kill() called more than once!"
The blk_get_request function may fail in low-memory conditions or during
device removal (even if __GFP_WAIT is set). To distinguish between these
errors, modify the blk_get_request call stack to return the appropriate
ERR_PTR. Verify that all callers check the return status and consider
IS_ERR instead of a simple NULL pointer check.
For consistency, make a similar change to the blk_mq_alloc_request leg
of blk_get_request. It may fail if the queue is dead, or the caller was
unwilling to wait.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd]
Acked-by: Boaz Harrosh <bharrosh@panasas.com> [for osd]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The blk-core dead queue checks introduce an error scenario to
blk_get_request that returns NULL if the request queue has been
shutdown. This affects the behavior for __GFP_WAIT callers, who should
verify the return value before dereferencing.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch fixes code such as the following with scsi-mq enabled:
rq = blk_get_request(...);
blk_rq_set_block_pc(rq);
rq->cmd = my_cmd_buffer; /* separate CDB buffer */
blk_execute_rq_nowait(...);
Code like this appears in e.g. sg_start_req() in drivers/scsi/sg.c (for
large CDBs only). Without this patch, scsi_mq_prep_fn() will set
rq->cmd back to rq->__cmd, causing the wrong CDB to be sent to the device.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These are the two bug fixes I mentioned in the final merge window pull. One
is a reversed logic check in the device busy tests which can cause a nasty
hang and another crash seen in the new SCSI pool support if the use count ever
goes to zero.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT85zGAAoJEDeqqVYsXL0Mnw4IAJ7BP+4nUlP7Oib8JfPu4Df2
b6dv3YEGe6th4awrHqUnATusjQLIybk/rgRKb6P50o1iX2VI+rs1mAm9esw9NalS
8aKzDMAv9pTRsRvAhe3AnIVGGCYAekV4AZWmsXQPCKqcsQZSZKAnIerLBf0lBemR
X3+1VhYtbB9z4o0Gpv4E5mR/7CqIouDpe5QGRKRY2+/Yyp2El6Vzwqr9XMLyOvmY
Y9WaIhM1UzABl+NAlDhMnA0Yw27UHJfWY6UWZ3Wa73DQCWsdZ6eydal4g8YNA5pB
+6UjMQKWh/bXHZl8v+eCuuXODXZQGazKOFFoc6SGumxAcuLraCBFsuU5m4AQ0NA=
=v+g2
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are the two bug fixes I mentioned in the final merge window
pull. One is a reversed logic check in the device busy tests which
can cause a nasty hang and another crash seen in the new SCSI pool
support if the use count ever goes to zero"
[ The device busy test already got merged from a patch earlier, so is
now duplicated. ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] save command pool address of Scsi_Host
[SCSI] fix qemu boot hang problem
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f9 ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a small set of updates which missed the first pull. It's more msix
updates, some iscsi and qla4xxx fixes, we also have some string null
termination fixes a return value fix and a couple of pm8001 firmware fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT7mGIAAoJEDeqqVYsXL0MikgIAKAa6LYOyOV8lK+BVBMR0Uhm
tV7ByzA2Ii1CX6I3QMeYziK9Jk9jfkPwia+gytef1gHui/O47m5oa0WJ6SaLJPa/
i5Zc2ZfhIi0tykEQQ6sXYZiIHkIx4yCJr/YPa/SzifyvDEKndtBUbXzpTTIWYMJG
gBjhVXapwNOJWfkWW6WE26DIpqr1Vhn3vU0IRFH9PQ1F8iLaKPwyJIpZSbZNxc9m
Uq3KKthKG2sZESHJpIjBq+fogGmtm0DSmiRPnDo5KsxoYXlrMgqK3JAs1NpIOZy/
Hg8raobuL2lzQFddBKx6PWZZgDb9P5KZvEEWpycNU8+xG1ny5qMe0AZoySs6eG4=
=JzXC
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI changes from James Bottomley:
"This is a small set of updates which missed the first pull. It's more
msix updates, some iscsi and qla4xxx fixes, we also have some string
null termination fixes a return value fix and a couple of pm8001
firmware fixes.
Just a note, we do have a couple of bug fixes coming under separate
cover, but they don't have to be part of the merge window"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
iscsi class: Fix freeing of skb in get host error path
scsi: fix u14-34f printk format warnings
pm8001: fix pm8001_store_update_fw
pm8001: Fix erratic calculation in update_flash
pm8001: Update MAINTAINERS list
libiscsi: return new error code when nop times out
iscsi class: fix get_host_stats return code when not supported
iscsi class: fix get_host_stats error handling
qla4xxx: fix get_host_stats error propagation
qla4xxx: check the return value of dma_alloc_coherent()
scsi: qla4xxx: ql4_mbx.c: Cleaning up missing null-terminate in conjunction with strncpy
scsi: qla4xxx: ql4_os.c: Cleaning up missing null-terminate in conjunction with strncpy
qla4xxx: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Use pci_enable_msix_exact() instead of pci_enable_msix()
If a scsi host driver specifies .cmd_len in it's scsi_host_template, a driver's
private command pool is needed. scsi_find_host_cmd_pool() will locate it, but
scsi_alloc_host_cmd_pool() isn't saving the pool address in the host template.
This will result in an access error when the host is removed.
Avoid the problem by saving the address of a new allocated command pool where
it is expected.
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 89d9a56795
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The latest kernel fails to boot qemu arm images when using scsi
for disk access. Boot gets stuck after the following messages.
brd: module loaded
sym53c8xx 0000:00:0c.0: enabling device (0100 -> 0103)
sym0: <895a> rev 0x0 at pci 0000:00:0c.0 irq 93
sym0: No NVRAM, ID 7, Fast-40, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi host0: sym-2.2.3
Bisect points to commit 71e75c97f9 ("scsi: convert device_busy to
atomic_t"). Code inspection shows the following suspicious change
in scsi_request_fn.
out_delay:
- if (sdev->device_busy == 0 && !scsi_device_blocked(sdev))
+ if (atomic_read(&sdev->device_busy) && !scsi_device_blocked(sdev))
blk_delay_queue(q, SCSI_QUEUE_DELAY);
}
'sdev->device_busy == 0' was replaced with 'atomic_read(&sdev->device_busy)',
meaning the logic was reversed. Changing this expression to
'!atomic_read(&sdev->device_busy)' fixes the problem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Acked-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: 71e75c97f9
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
Pull networking fixes from David Miller:
"I'm sending this out, in particular, to get the iwlwifi fix
propagated:
1) Fix build due to missing include in i40e driver, from Lucas
Tanure.
2) Memory leak in openvswitch port allocation, from Chirstoph Jaeger.
3) Check DMA mapping errors in myri10ge, from Stanislaw Gruszka.
4) Fix various deadlock scenerios in sunvnet driver, from Sowmini
Varadhan.
5) Fix cxgb4i build failures with incompatible Kconfig settings of
the driver vs ipv6, from Anish Bhatt.
6) Fix generation of ACK packet timestamps in the presence of TSO
which will be split up, from Willem de Bruijn.
7) Don't enable sched scan in iwlwifi driver, it causes firmware
crashes in some revisions. From Emmanuel Grumbach.
8) Revert a macvlan simplification that causes crashes.
9) Handle RTT calculations properly in the presence of repair'd SKBs,
from Andrey Vagin.
10) SIT tunnel lookup uses wrong device index in compares, from
Shmulik Ladkani.
11) Handle MTU reductions in TCP properly for ipv4 mapped ipv6
sockets, from Neal Cardwell.
12) Add missing annotations in rhashtable code, from Thomas Graf.
13) Fix false interpretation of two RTOs as being from the same TCP
loss event in the FRTO code, from Neal Cardwell"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
netlink: Annotate RCU locking for seq_file walker
rhashtable: fix annotations for rht_for_each_entry_rcu()
rhashtable: unexport and make rht_obj() static
rhashtable: RCU annotations for next pointers
tcp: fix ssthresh and undo for consecutive short FRTO episodes
tcp: don't allow syn packets without timestamps to pass tcp_tw_recycle logic
tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
sit: Fix ipip6_tunnel_lookup device matching criteria
net: ethernet: ibm: ehea: Remove duplicate object from Makefile
net: xgene: Check negative return value of xgene_enet_get_ring_size()
tcp: don't use timestamp from repaired skb-s to calculate RTT (v2)
net: xilinx: Remove .owner field for driver
Revert "macvlan: simplify the structure port"
iwlwifi: mvm: disable scheduled scan to prevent firmware crash
xen-netback: remove loop waiting function
xen-netback: don't stop dealloc kthread too early
xen-netback: move NAPI add/remove calls
xen-netback: fix debugfs entry creation
xen-netback: fix debugfs write length check
net-timestamp: fix missing tcp fragmentation cases
...
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wOm0
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
"Main set of InfiniBand/RDMA updates for 3.17 merge window:
- MR reregistration support
- MAD support for RMPP in userspace
- iSER and SRP initiator updates
- ocrdma hardware driver updates
- other fixes..."
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (52 commits)
IB/srp: Fix return value check in srp_init_module()
RDMA/ocrdma: report asic-id in query device
RDMA/ocrdma: Update sli data structure for endianness
RDMA/ocrdma: Obtain SL from device structure
RDMA/uapi: Include socket.h in rdma_user_cm.h
IB/srpt: Handle GID change events
IB/mlx5: Use ARRAY_SIZE instead of sizeof/sizeof[0]
IB/mlx4: Use ARRAY_SIZE instead of sizeof/sizeof[0]
RDMA/amso1100: Check for integer overflow in c2_alloc_cq_buf()
IPoIB: Remove unnecessary test for NULL before debugfs_remove()
IB/mad: Add user space RMPP support
IB/mad: add new ioctl to ABI to support new registration options
IB/mad: Add dev_notice messages for various umad/mad registration failures
IB/mad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid multicast join attempts with invalid P_key
IB/umad: Update module to [pr|dev]_* style print messages
IB/ipoib: Avoid flushing the workqueue from worker context
IB/ipoib: Use P_Key change event instead of P_Key polling mechanism
IB/ipath: Add P_Key change event support
mlx4_core: Add support for secure-host and SMP firewall
...
Previous guard of IS_ENABLED(CONFIG_IPV6) is not sufficient when cxgbi drivers
are built into kernel but ipv6 is not.
v2: Use Kconfig to disable compiling cxgbi built into kernel when ipv6 is
compiled as a module
Fixes: e81fbf6cd6 ("libcxgbi:cxgb4i Guard ipv6 code with a config check")
Fixes: fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace obsolete strict_strto with more appropriate kstrto calls
Signed-off-by: Daniel Walter <dwalter@google.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
These belong to the t4 msg header, will ensure there is no accidental code
duplication in the future
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to the ftrace function callback infrastructure. It's introducing a
way to allow different functions to call directly different trampolines
instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which always
had a different trampoline, but the function tracer trampoline was called
and did basically nothing, and then the function graph tracer trampoline
was called. The difference now, is that the function graph tracer
trampoline can be called directly if a function is only being traced by
the function graph trampoline. If function tracing is also happening on
the same function, the old way is still done.
The accounting for this takes up more memory when function graph tracing
is activated, as it needs to keep track of which functions it uses.
I have a new way that wont take as much memory, but it's not ready yet
for this merge window, and will have to wait for the next one.
Another big change was the removal of the ftrace_start/stop() calls that
were used by the suspend/resume code that stopped function tracing when
entering into suspend and resume paths. The stop of ftrace was done
because there was some function that would crash the system if one called
smp_processor_id()! The stop/start was a big hammer to solve the issue
at the time, which was when ftrace was first introduced into Linux.
Now ftrace has better infrastructure to debug such issues, and I found
the problem function and labeled it with "notrace" and function tracing
can now safely be activated all the way down into the guts of suspend
and resume.
Other changes include clean ups of uprobe code.
Clean up of the trace_seq() code.
And other various small fixes and clean ups to ftrace and tracing.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT35zXAAoJEKQekfcNnQGuOz0H/38zqM0nLFhrgvz3EPk2UOjn
xqpX8qyb2V7TJZL+IqeXU2a5cQZl5ba0D4WtBGpxbTae3CJYiuQ87iKUNFoH0om5
FDpn80igb368k8V3qRdRsziKVCCf0XBd/NkHJXc0ZkfXGyzB2Ga4bBxALxp2gj9y
bnO+vKo6+tWYKG4hyQb4P3LRXUrK8/LWEsPr39cH2QH1Rdj69Lx9CgrCdUVJmwcb
Bj8hEiLXL/RYCFNn79A3wNTUvW0rG/AOIf4SLqXtasSRZ0ToaU0ZyDnrNv+0Ol47
rX8tSk+LfXchL9hpIvjCf1vlAYq3pO02favteR/jip3lx/dTjEDE4RJ9qtJzZ4Q=
=fwQY
-----END PGP SIGNATURE-----
Merge tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"This pull request has a lot of work done. The main thing is the
changes to the ftrace function callback infrastructure. It's
introducing a way to allow different functions to call directly
different trampolines instead of all calling the same "mcount" one.
The only user of this for now is the function graph tracer, which
always had a different trampoline, but the function tracer trampoline
was called and did basically nothing, and then the function graph
tracer trampoline was called. The difference now, is that the
function graph tracer trampoline can be called directly if a function
is only being traced by the function graph trampoline. If function
tracing is also happening on the same function, the old way is still
done.
The accounting for this takes up more memory when function graph
tracing is activated, as it needs to keep track of which functions it
uses. I have a new way that wont take as much memory, but it's not
ready yet for this merge window, and will have to wait for the next
one.
Another big change was the removal of the ftrace_start/stop() calls
that were used by the suspend/resume code that stopped function
tracing when entering into suspend and resume paths. The stop of
ftrace was done because there was some function that would crash the
system if one called smp_processor_id()! The stop/start was a big
hammer to solve the issue at the time, which was when ftrace was first
introduced into Linux. Now ftrace has better infrastructure to debug
such issues, and I found the problem function and labeled it with
"notrace" and function tracing can now safely be activated all the way
down into the guts of suspend and resume
Other changes include clean ups of uprobe code, clean up of the
trace_seq() code, and other various small fixes and clean ups to
ftrace and tracing"
* tag 'trace-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (57 commits)
ftrace: Add warning if tramp hash does not match nr_trampolines
ftrace: Fix trampoline hash update check on rec->flags
ring-buffer: Use rb_page_size() instead of open coded head_page size
ftrace: Rename ftrace_ops field from trampolines to nr_trampolines
tracing: Convert local function_graph functions to static
ftrace: Do not copy old hash when resetting
tracing: let user specify tracing_thresh after selecting function_graph
ring-buffer: Always run per-cpu ring buffer resize with schedule_work_on()
tracing: Remove function_trace_stop and HAVE_FUNCTION_TRACE_MCOUNT_TEST
s390/ftrace: remove check of obsolete variable function_trace_stop
arm64, ftrace: Remove check of obsolete variable function_trace_stop
Blackfin: ftrace: Remove check of obsolete variable function_trace_stop
metag: ftrace: Remove check of obsolete variable function_trace_stop
microblaze: ftrace: Remove check of obsolete variable function_trace_stop
MIPS: ftrace: Remove check of obsolete variable function_trace_stop
parisc: ftrace: Remove check of obsolete variable function_trace_stop
sh: ftrace: Remove check of obsolete variable function_trace_stop
sparc64,ftrace: Remove check of obsolete variable function_trace_stop
tile: ftrace: Remove check of obsolete variable function_trace_stop
ftrace: x86: Remove check of obsolete variable function_trace_stop
...
If get_host_stats failes we are using kfree to free the
skb. We should be using kfree_skb.
This patch was made over Christoph's scsi-queue drivers-for-3.17 branch.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As pointed out by the intel guys, there is no need to hold rcu read lock in
cxgbi_inet6addr_handler(), this patch removes it.
Fixes: 759a0cc5a3 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6 api")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If scsi_remove_host() is called while an rport is in the blocked state
then scsi_remove_host() will only finish if the rport is unblocked
from inside a timer function. Make sure that an rport only enters the
blocked state if a timer will be started that will unblock it. This
avoids that unloading the ib_srp kernel module after having
disconnected the initiator from the target system results in a
deadlock if both the fast_io_fail_tmo and dev_loss_tmo parameters have
been set to "off".
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: David Dillow <dave@thedillows.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix printk format warnings (seen on i386 builds):
../drivers/scsi/u14-34f.c: In function 'port_detect':
../drivers/scsi/u14-34f.c:630:28: warning: format '%u' expects argument of type 'unsigned int', but argument 4 has type 'u64' [-Wformat=]
../drivers/scsi/u14-34f.c: In function 'u14_34f_queuecommand_lck':
../drivers/scsi/u14-34f.c:1290:25: warning: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type 'int' [-Wformat=]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The current implementation may mix the negative value returned from
pm8001_set_nvmd with count. -(-ENOMEM) could be interpreted as bytes
programmed, this patch fixes it.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The loopcount is calculated by using some weird magic. Use instead a boring
macro.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a iscsi nop as ping timedout we were failing with the
common connection error code, ISCSI_ERR_CONN_FAILED. This
patch adds a new error code for this problem so can properly
track/distinguish in userspace.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When the get_host_stats call was not supported we were
returing EINVAL. This has us return ENOSYS, because for
software iscsi drivers where there is no host it is ok to not
have this callout.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
iscsi_get_host_stats was dropping the error code returned
by drivers like qla4xxx.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
qla4xxx was not always returning -EXYZ error codes when
qla4xxx_get_host_stats failed.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
the qla4xxx_alloc_fw_dump() calls dma_alloc_coherent() but does not
check its return value.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-By: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
And in some cases modified to copy one character less than the overall
length, as the entire area is already zeroed.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-By: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-By: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Reviewed-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some devices don't like REPORT SUPPORTED OPERATION CODES and will
simply timeout causing sd_mod init to take a very very long time.
Introduce BLIST_NO_RSOC scsi scan flag, that stops RSOC from being
issued. Add it to Promise Vtrak E610f entry in scsi scan
blacklist. Fixes bug #79901 reported at
https://bugzilla.kernel.org/show_bug.cgi?id=79901
Fixes: 98dcc2946adb ("SCSI: sd: Update WRITE SAME heuristics")
Signed-off-by: Janusz Dziemidowicz <rraptorr@nails.eu.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Arvind Kumar <arvindkumar@vmware.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When a call to request_irq() failed pm8001_setup_msix()
still returns the success. This udate fixes the described
misbehaviour.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Artur Paszkiewicz <artur.paszkiewicz@intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Function pci_enable_msix() should not be called in case
it threw a negative errno from a previous call.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: "Suma Ramars (sramars)" <sramars@cisco.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
hostt->name might contain space, so use the ->proc_name short name instead
when creating per-driver command slabs.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: poma <pomidorabelisima@gmail.com>
Tested-by: poma <pomidorabelisima@gmail.com>
Reviewed-by: Vladimir Davydov <vdavydov@parallels.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
- add host_lock option whose default value is 0 which removes the
host_lock around all queued commands
- accept delay=-1 (_hi_) or -2 which use a tasklet to invoke
the scsi_done callback into the mid-layer. The default
is still delay=1 which uses a timer to delay 1 jiffy
- wire .change_queue_depth and .change_queue_type
functions to better simulate queueing in a modern LLD
- add SCSI_DEBUG_OPT_Q_NOISE (0x200) mask to only produce
debug output associated with queue full, plus from
.change_queue_depth and .change_queue_type functions
- add SCSI_DEBUG_OPT_ALL_TSF (0x400) mask which reports
all queued_arr fulls at TASK_SET_FULL, otherwise
SCSI_MLQUEUE_HOST_BUSY is returned
- add SCSI_DEBUG_OPT_RARE_TSF (0x800) mask which works
together with the every_nth option (> 0) to count
occurrences of num_in_q==queue_depth. When every_nth
is reached the victim (a command) yields TASK SET FULL
- clean up many debug messages.
- add ndelay=<nanosecs> option that uses high resolution
timers; active if > 0 and then overrides delay= option
- expand Unit Attention handling: POR, BUS_RESET and
MODE PARAMETERS CHANGED
- support .eh_target_reset_handler and drop .bios_param
- add OPT_N_WCE mask so caching page yields WCE=0
- add OPT_RESET_NOISE mask to log aborts and resets
- add OPT_NO_CDB_NOISE mask to not log each cdb
- MODE SELECT support for changing caching page's WCE
- name common ioctls in log
- when fake_rw=1, do not vmalloc fake store; make
UNMAP and WRITE SAME obey fake_rw
- more logging and code improvements including better
sense buffer handling
With fio and four (pseudo) devices I have observed 1.2 M IOPS
on my equipment. Rob Elliott who has done much testing and made
numerous suggestions, has better IOPS results than mine.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add blist flags to permit the reading of the VPD pages even when
the target may claim SPC-2 compliance. MSFT targets currently
claim SPC-2 compliance while they implement post SPC-2 features.
With this patch we can correctly handle WRITE_SAME_16 issues.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix many warnings with incorrect endian assumptions
which makes the code unportable to new architectures.
The UFS specification defines the byte order as big-endian
for UPIU structure and little-endian for the host controller
transfer/task management descriptors.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Instead of copying information to fw_control_context free it.
The task is forgotten thus also the reference to fw_control_context
and the completion thread takes the info from virt_ptr again.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The driver checks the return valu, but after he tries to wait_for_completion
which might never happen. Also the ioctl buffer is freed at the end of the
function, so the first removal is not needed.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
ccb->fw_control_context is copied to local fw_control_context and
the local variable is never used later
Free ccb->fw_control_context. The task is forgotten thus also the
reference to fw_control_context and the completion thread takes the info
from virt_ptr again.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppche
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Removal of null pointer checks that could never happen
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The driver ignores the return value in a lot of places, fix
it at least somewhere (and release the resources in such cases),
to avoid that bad things happen.
A memory leak is fixed too.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Patch adds a new spinlock to protect the ccb management.
It may happen that concurrent threads become the same tag value
from the 'alloc' function', the spinlock prevents this situation.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The driver ignores the return value in a lot of places, fix
it at least somewhere (and release the resources in such cases),
to avoid that bad things happen.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In the driver two different functions are used to free the same resource,
this patch makes the code easier to read. In addittion to that, some
minor optimisations were made too.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
During hibernation, the HBA firmware may lose power and forget the device
id info. This causes the HBA to reject IO upon resume. The fix is
to call the libsas power management routines to make the domain device
forgetful.
This fixes bug 76681: https://bugzilla.kernel.org/show_bug.cgi?id=76681
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_probe, delay the call to scsi_add_host until the host has been
fully set up.
Otherwise, the default .can_queue value of 1 causes scsi-mq to set the block
layer request queue size to its minimum size, resulting in awful performance.
In _scsih_probe error handling, call mpt3sas_base_detach rather than
scsi_remove_host to properly clean up in reverse order.
In _scsih_remove, call scsi_remove_host earlier to clean up in reverse order.
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@avagotech.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_probe, delay the call to scsi_add_host until the host has been
fully set up.
Otherwise, the default .can_queue value of 1 causes scsi-mq to set the block
layer request queue size to its minimum size, resulting in awful performance.
In _scsih_probe error handling, call mpt3sas_base_detach rather than
scsi_remove_host to properly clean up in reverse order.
In _scsih_remove, call scsi_remove_host earlier to clean up in reverse order.
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@avagotech.com>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On some Windows hosts on FC SANs, TEST_UNIT_READY can return SRB_STATUS_ERROR.
Correctly handle this. Note that there is sufficient sense information to
support scsi error handling even in this case.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Correctly set SRB flags for all valid I/O directions. Some IHV drivers on the
Windows host require this. The host validates the command and SRB flags
prior to passing the command down to native driver stack.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On Azure, we have seen instances of unbounded I/O latencies. To deal with
this issue, implement handler that can reset the timeout. Note that the
host gaurantees that it will respond to each command that has been issued.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
[hch: added a better comment explaining the issue]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Based on the negotiated VMBUS protocol version, we adjust the size of the storage
protocol messages. The two sizes we currently handle are pre-win8 and post-win8.
In WS2012 R2, we are negotiating higher VMBUS protocol version than the win8
version. Make adjustments to correctly handle this.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Going forward it is possible that some of the commands that are not currently
implemented will be implemented on future Windows hosts. Even if they are not
implemented, we are told the host will corrrectly handle unsupported
commands (by returning appropriate return code and sense information).
Make command filtering depend on the host version.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Set cmd_per_lun to reflect value supported by the Host.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Hyper-V hosts can support multiple targets and multiple channels and larger number of
LUNs per target. Update the code to reflect this. With this patch we can correctly
enumerate all the paths in a multi-path storage environment.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
If the controller doesn't support 64-bit addressing mode, it must not
set the DMA mask to 64-bit. But it's unconditionally trying to set to
64-bit without checking 64-bit addressing support in the controller
capabilities.
It was correctly checked before commit 3b1d05807a
("[SCSI] ufs: Segregate PCI Specific Code"), this aims to restores
the correct behaviour.
To achieve this in a generic way, firstly we should push down the DMA
mask setting routine ufshcd_set_dma_mask() from PCI glue driver to core
driver in order to do it for both PCI glue driver and Platform glue
driver. Secondly, we should change pci_ DMA mapping API to dma_ DMA
mapping API because core driver is independent of glue drivers.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The data byte count field of PRDT indicates the length of data block
which is a segment of data transfer for SCSI commands. The value of
this field shall have Dword granularity and the the maximum of length
is 256KB.
This adjusts dma pad mask and max segment size to the above-mentioned
PRDT limitations.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Vinayak Holikatti <vinholikatti@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
UFS 1.1 specification does not support MAINTENANCE IN(0xA3) SCSI
command and hence it doesn't support REPORT SUPPORTED OPERATION CODES
as well.
Change-Id: Ic09c5b46b2511b1c28db478023c32b898ac69e6d
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In interrupt context, after reading and comparing the UTRLDBR to
hba->outstanding_request and before resetting the interrupt aggregation,
there might be completion of another transfer request (TR). Such TRs might
get stuck, pending, until the next interrupt is generated (if any).
Changing the sequence of resetting the interrupt aggregation first and
then reading UTRLDBR status, will assure that completed TRs won't get
stuck pending.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some UFS devices may expose bLUQueueDepth field as zero indicating
that the queue depth depends on the number of resources available
for LUN at a particular instant to handle the outstanding transfer
requests. Currently, when response for SCSI command is TASK_FULL
the LLD decrements the queue depth but fails to increment when the
resources are available. The scsi mid-layer handles the change in
queue depth heuristically and offers simple interface with
->change_queue_depth.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Some of the UFS devices may support different number of commands
that can be queued per LU. At the current implementation,
SW configure each of the UFS devices LU's according to the
controller capability.
In this patch the queue depth available per LU is read and updated in
the LU's SW structure.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Check query response status before copying the response.
Add descriptor query response size check, before copying it to buffer.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Introduces the API for sending queries with descriptors.
A descriptor is a block or page of parameters that describe the device.
The descriptors are classified into types and can range in size
from 2 bytes through 255 bytes.
All descriptors have a length value as their first element, and a type
identification element as their second byte.
All descriptors are readable and some may be write once.
They are accessed using their type, index and selector.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Acked-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The if_info pointer is not released by the mgmt_set_ip() function
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
change_queue_depth allows changing per-target queue depth via sysfs.
It also allows the SCSI midlayer to ramp down the number of concurrent
inflight requests in response to a SCSI BUSY status response and allows
the midlayer to ramp the count back up to the device maximum when the
BUSY condition has resolved.
Signed-off-by: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The spinlock of tgt_lock is only for serializing read and write
req_vq, one lockless seqcount is enough for the purpose.
On one 16core VM with vhost-scsi backend, the patch can improve
IOPS with 3% on random read test.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
[Add initialization in virtscsi_target_alloc. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When copy_from_user fails, return -EFAULT, not -ENOMEM
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Joe Handzik <joseph.t.handzik@hp.com>
Reviewed-by: Scott Teel <scott.teel@hp.com>
Reviewed by: Mike MIller <michael.miller@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
When devices come on line, they should be removed from the list of
offline devices that are monitored.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reviewed-by: Scott Teel <scott.teel@hp.com>
Reviewed-by: Joe Handzik <joseph.t.handzik@hp.com>
Reviewed by: Mike MIller <michael.miller@canonical.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
commit 28e1344647 "[SCSI] hpsa: enable unit attention reporting"
turns on unit attention notifications, but got the change wrong for
all architectures other than x86, which now store an uninitialized
value into the device register.
Gcc helpfully warns about this:
../drivers/scsi/hpsa.c: In function 'hpsa_set_driver_support_bits':
../drivers/scsi/hpsa.c:6373:17: warning: 'driver_support' is used uninitialized in this function [-Wuninitialized]
driver_support |= ENABLE_UNIT_ATTN;
^
This moves the #ifdef so only the prefetch-enable is conditional
on x86, not also reading the initial register contents.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 28e1344647 "[SCSI] hpsa: enable unit attention reporting"
Cc: stable@vger.kernel.org # v3.14+
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reviewed-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
a 6-byte READ/WRITE CDB with a 0 block data transfer really
means a 256 block data transfer. The RAID mapping code failed
to handle this case. For 10/12/16 byte READ/WRITEs, 0 just means
no data should be transferred, and should not trigger BUG_ON.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reported-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Reviewed-by: Joe Handzik <joseph.t.handzik@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands bnx2fc driver as a QLogic driver
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands bnx2i driver as a QLogic driver
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On systems with a non power-of-two CPU count the existing MSI-X grouping
code failed to distribute interrupts correctly. Rework the code to
handle arbitrary processor counts.
Also remove the hardcoded upper limit on the number of processors so we
can boot on large systems.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
On systems with a non power-of-two CPU count the existing MSI-X grouping
code failed to distribute interrupts correctly. Rework the code to
handle arbitrary processor counts.
Also remove the hardcoded upper limit on the number of processors so we
can boot on large systems.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Sreekanth Reddy <Sreekanth.reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tack the firmware reply event_data payload to the end of its
corresponding struct fw_event_work allocation. This matches the
convention in the mptfusion driver and simplifies the code.
This avoids the following smatch warning:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:2519
mpt3sas_send_trigger_data_event() warn: possible memory leak of
'fw_event'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_{slave,target}_alloc, an incorrect structure type is passed
to sizeof() when allocating storage for hostdata. Luckily larger
structure types were used, so at least the wrong sizes were safe:
struct scsi_device (1784 bytes) > struct MPT3SAS_DEVICE (24 bytes)
struct scsi_target (760 bytes) > struct MPT3SAS_TARGET (32 bytes)
This fixes the following smatch warnings:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1166 _scsih_target_alloc()
warn: struct type mismatch 'MPT3SAS_TARGET vs scsi_target'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:1280 _scsih_slave_alloc()
warn: struct type mismatch 'MPT3SAS_DEVICE vs scsi_device'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The MPT2SAS_ADAPTER reply_post_host_index[] holds calculated addresses
in memory mapped register space. Add an "__iomem" annotation to silence
the following sparse warnings:
drivers/scsi/mpt2sas/mpt2sas_base.c:1006:43:
warning: incorrect type in argument 2 (different address spaces)
expected void volatile [noderef] <asn:2>*addr
got unsigned long long [usertype] *<noident>
drivers/scsi/mpt2sas/mpt2sas_base.c:4299:22:
warning: cast removes address space of expression
drivers/scsi/mpt2sas/mpt2sas_base.c:4303:27:
warning: cast removes address space of expression
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tack the firmware reply event_data payload to the end of its
corresponding struct fw_event_work allocation. This matches the
convention in the mptfusion driver and simplifies the code.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In _scsih_{slave,target}_alloc, an incorrect structure type is passed
to sizeof() when allocating storage for hostdata. Luckily larger
structure types were used, so at least the wrong sizes were safe:
struct scsi_device (1784 bytes) > struct MPT2SAS_DEVICE (24 bytes)
struct scsi_target (760 bytes) > struct MPT2SAS_TARGET (40 bytes)
This fixes the following smatch warnings:
drivers/scsi/mpt2sas/mpt2sas_scsih.c:1295 _scsih_target_alloc()
warn: struct type mismatch 'MPT2SAS_TARGET vs scsi_target'
drivers/scsi/mpt2sas/mpt2sas_scsih.c:1409 _scsih_slave_alloc()
warn: struct type mismatch 'MPT2SAS_DEVICE vs scsi_device'
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Building an allmodconfig ARM kernel, I get multiple such
warnings because of a spinlock contained in packed structure
in the 3w-xxxx driver:
../drivers/scsi/3w-xxxx.c: In function 'tw_chrdev_ioctl':
../drivers/scsi/3w-xxxx.c:1001:68: warning: mis-aligned access used for structure member [-fstrict-volatile-bitfields]
timeout = wait_event_timeout(tw_dev->ioctl_wqueue, tw_dev->chrdev_request_id == TW_IOCTL_CHRDEV_FREE, timeout);
^
../drivers/scsi/3w-xxxx.c:1001:68: note: when a volatile object spans multiple type-sized locations, the compiler must choose between using a single mis-aligned access to preserve the volatility, or using multiple aligned accesses to avoid runtime faults; this code may fail at runtime if the hardware does not allow this access
The same bug apparently was present in 3w-sas and 3w-9xxx, but has been
fixed in the past. This patch uses the same fix by moving the pragma
in front of the TW_Device_Extension definition, so it only covers
hardware structures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adam Radford <aradford@gmail.com>
Cc: Adam Radford <linuxraid@lsi.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The NCR53c406a scsi driver normally does not use DMA, unless
the USE_PIO macro is disabled by modifying the source code.
The call to free_dma() for some reason uses #ifdef USE_DMA,
which does not do the right thing, since USE_DMA is defined
as a boolean that is either 0 or 1, but always present.
One case where it gets in the way is randconfig builds on ARM,
which depending on the configuration does not provide a free_dma()
function, causing this build error:
drivers/scsi/NCR53c406a.c: In function 'NCR53c406a_release':
drivers/scsi/NCR53c406a.c:600:3: error: implicit declaration of function 'free_dma' [-Werror=implicit-function-declaration]
free_dma(shost->dma_channel);
^
This changes the code to use #if USE_DMA, to match the
rest of the file, which seems to be what the author intended.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The qlogicfas scsi driver does not use DMA, and the call to free_dma()
in its exit function seems to have been copied incorrectly from
another driver but never caused trouble.
One case where it gets in the way is randconfig builds on ARM,
which depending on the configuration does not provide a free_dma()
function, causing this build error:
drivers/scsi/qlogicfas.c: In function 'qlogicfas_release':
drivers/scsi/qlogicfas.c:175:3: error: implicit declaration of function 'free_dma' [-Werror=implicit-function-declaration]
free_dma(shost->dma_channel);
^
Removing the incorrect function calls should be the obvious
fix for this, with no downsides.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The pas16 scsi driver does not use DMA, and the call to free_dma()
in its exit function seems to have been copied incorrectly from
another driver but never caused trouble.
One case where it gets in the way is randconfig builds on ARM,
which depending on the configuration does not provide a free_dma()
function, causing this build error:
drivers/scsi/pas16.c: In function 'pas16_release':
drivers/scsi/pas16.c:611:3: error: implicit declaration of function 'free_dma' [-Werror=implicit-function-declaration]
free_dma(shost->dma_channel);
Removing the incorrect function calls should be the obvious
fix for this, with no downsides.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The advansys SCSI driver uses the dma_cache_sync function, which is
not available on the ARM architecture, and cannot be implemented
correctly, so we always get this build error:
drivers/scsi/advansys.c: In function 'advansys_get_sense_buffer_dma':
drivers/scsi/advansys.c:7882:2: error: implicit declaration of function 'dma_cache_sync' [-Werror=implicit-function-declaration]
dma_cache_sync(board->dev, scp->sense_buffer,
^
It seems nobody has missed this driver so far, so let's just
disable it for ARM to help randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Added big endian annotations to relevant data structure fields, and necessary
byte swappings to support little endian builds.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use macro definition
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
bfa_swap_words() shifts its argument (assumed to be 64-bit) by 32 bits
each way. In two places the argument type is dma_addr_t, which may be
32-bit, in which case the effect of the bit shift is undefined:
drivers/scsi/bfa/bfa_fcpim.c: In function 'bfa_ioim_send_ioreq':
drivers/scsi/bfa/bfa_fcpim.c:2497:4: warning: left shift count >= width of type [enabled by default]
addr = bfa_sgaddr_le(sg_dma_address(sg));
^
drivers/scsi/bfa/bfa_fcpim.c:2497:4: warning: right shift count >= width of type [enabled by default]
drivers/scsi/bfa/bfa_fcpim.c:2509:4: warning: left shift count >= width of type [enabled by default]
addr = bfa_sgaddr_le(sg_dma_address(sg));
^
drivers/scsi/bfa/bfa_fcpim.c:2509:4: warning: right shift count >= width of type [enabled by default]
Avoid this by adding casts to u64 in bfa_swap_words().
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Cc: stable@vger.kernel.org
Fixes: f16a17507b ('[SCSI] bfa: remove all OS wrappers')
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Anil Gurumurthy <anil.gurumurthy@qlogic.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Use kstrdup when the goal of an allocation is copy a string into the
allocated region.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression from,to;
expression flag,E1,E2;
statement S;
@@
- to = kmalloc(strlen(from) + 1,flag);
+ to = kstrdup(from, flag);
... when != \(from = E1 \| to = E1 \)
if (to==NULL || ...) S
... when != \(from = E2 \| to = E2 \)
- strcpy(to, from);
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Christoph Hellwig <hch@lst.de>
These speeds are to support the next generation of FCoE port speeds.
Signed-off-by: Dick Kennedy <Dick.Kennedy@Emulex.Com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The custom stats is an array with custom_length indicating the length
of the array. This patch fixes bnx2i and be2iscsi's setting of the
custom stats length. They both just have the one, eh_abort_cnt, so that should
be in the first entry of the custom array and custom_length should then
be one.
Reported-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Remove two redundant casts from char * to char *.
Signed-off-by: Nick Black <nlb@google.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The Kconfig symbols SCSI_TGT and SCSI_FC_TGT_ATTRS are unused since
"tgt: removal". Setting them has no effect. Remove these symbols.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Commit ID: 7e660100d8 added code to derive the
FLUSH_TIMEOUT from the basic I/O timeout. However, this patch did not use the
basic I/O timeout of the device. Fix this bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Despite supporting modern SCSI features some storage devices continue to
claim conformance to an older version of the SPC spec. This is done for
compatibility with legacy operating systems.
Linux by default will not attempt to read VPD pages on devices that
claim SPC-2 or older. Introduce a blacklist flag that can be used to
trigger VPD page inquiries on devices that are known to support them.
Reported-by: KY Srinivasan <kys@microsoft.com>
Tested-by: KY Srinivasan <kys@microsoft.com>
Reviewed-by: KY Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We currently set the field in common code based on the device type,
but then only use it in the cdrom driver which also overrides the
value previously set in the generic code.
Just leave this entirely to the CDROM driver to make everyones life
simpler.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Add two new device types, most importantly the zoned block device
one.
Split from an earlier patch by Hannes Reinecke.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Current the midlayer fakes up a struct request for the explicit reset
ioctls, and those don't have a tag allocated to them. The fnic driver pokes
into midlayer structures to paper over this design issue, but that won't
work for the blk-mq case.
Either someone who can actually test the hardware will have to come up with
a similar hack for the blk-mq case, or we'll have to bite the bullet and fix
the way the EH ioctls work for real, but until that happens we fail these
explicit requests here.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Cc: Hiral Patel <hiralpat@cisco.com>
Cc: Suma Ramars <sramars@cisco.com>
Cc: Brian Uchino <buchino@cisco.com>
This patch adds support for an alternate I/O path in the scsi midlayer
which uses the blk-mq infrastructure instead of the legacy request code.
Use of blk-mq is fully transparent to drivers, although for now a host
template field is provided to opt out of blk-mq usage in case any unforseen
incompatibilities arise.
In general replacing the legacy request code with blk-mq is a simple and
mostly mechanical transformation. The biggest exception is the new code
that deals with the fact the I/O submissions in blk-mq must happen from
process context, which slightly complicates the I/O completion handler.
The second biggest differences is that blk-mq is build around the concept
of preallocated requests that also include driver specific data, which
in SCSI context means the scsi_cmnd structure. This completely avoids
dynamic memory allocations for the fast path through I/O submission.
Due the preallocated requests the MQ code path exclusively uses the
host-wide shared tag allocator instead of a per-LUN one. This only
affects drivers actually using the block layer provided tag allocator
instead of their own. Unlike the old path blk-mq always provides a tag,
although drivers don't have to use it.
For now the blk-mq path is disable by defauly and must be enabled using
the "use_blk_mq" module parameter. Once the remaining work in the block
layer to make blk-mq more suitable for slow devices is complete I hope
to make it the default and eventually even remove the old code path.
Based on the earlier scsi-mq prototype by Nicholas Bellinger.
Thanks to Bart Van Assche and Robert Elliot for testing, benchmarking and
various sugestions and code contributions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Blk-mq drivers usually preallocate their S/G list as part of the request,
but if we want to support the very large S/G lists currently supported by
the SCSI code that would tie up a lot of memory in the preallocated request
pool. Add support to the scatterlist code so that it can initialize a
S/G list that uses a preallocated first chunks and dynamically allocated
additional chunks. That way the scsi-mq code can preallocate a first
page worth of S/G entries as part of the request, and dynamically extend
the S/G list when needed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Replace the calls to the various blk_end_request variants with opencode
equivalents. Blk-mq is using a model that gives the driver control
between the bio updates and the actual completion, and making the old
code follow that same model allows us to keep the code more similar for
both paths.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
This saves us an atomic operation for each I/O submission and completion
for the usual case where the driver doesn't set a per-target can_queue
value. Only a few iscsi hardware offload drivers set the per-target
can_queue value at the moment.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Seems like these counters are missing any sort of synchronization for
updates, as a over 10 year old comment from me noted. Fix this by
using atomic counters, and while we're at it also make sure they are
in the same cacheline as the _busy counters and not needlessly stored
to in every I/O completion.
With the new model the _busy counters can temporarily go negative,
so all the readers are updated to check for > 0 values. Longer
term every successful I/O completion will reset the counters to zero,
so the temporarily negative values will not cause any harm.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Avoid taking the queue_lock to check the per-device queue limit. Instead
we do an atomic_inc_return early on to grab our slot in the queue,
and if necessary decrement it after finishing all checks.
Unlike the host and target busy counters this doesn't allow us to avoid the
queue_lock in the request_fn due to the way the interface works, but it'll
allow us to prepare for using the blk-mq code, which doesn't use the
queue_lock at all, and it at least avoids a queue_lock round trip in
scsi_device_unbusy, which is still important given how busy the queue_lock
is.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Avoid taking the host-wide host_lock to check the per-host queue limit.
Instead we do an atomic_inc_return early on to grab our slot in the queue,
and if necessary decrement it after finishing all checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Avoid taking the host-wide host_lock to check the per-target queue limit.
Instead we do an atomic_inc_return early on to grab our slot in the queue,
and if necessary decrement it after finishing all checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Prepare for not taking a host-wide lock in the dispatch path by pushing
the lock down into the places that actually need it. Note that this
patch is just a preparation step, as it will actually increase lock
roundtrips and thus decrease performance on its own.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
The blk-mq code path will set this to a different function, so make the
code simpler by setting it up in a legacy-request specific place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Make sure we only have the logic for requeing commands in one place.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Factor out a helper to set the _blocked values, which we'll reuse for the
blk-mq code path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Webb Scales <webbnh@hp.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Robert Elliott <elliott@hp.com>
Factor out command setup code that will be shared with the blk-mq code path.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Fixes: fc8d0590d9 ("libcxgbi: Add ipv6 api to driver")
Fixes: 759a0cc5a3 ("cxgb4i: Add ipv6 code to driver, call into libcxgbi ipv6
api")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out a function to initialize regular read/write commands and leave
sd_init_command as a simple dispatcher to the different prepare routines.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Currently cmd->allowed is initialized from rq->retries for discard
commands, but retries is always 0 for non-BLOCK_PC requests. Set it
to the standard number of retries instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Currently cmd->allowed is initialized from rq->retries for write same
commands, but retries is always 0 for non-BLOCK_PC requests. Set it
to the standard number of retries instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Simplify handling of discard requests by setting up the command directly
instead of initializing request fields and then calling
scsi_setup_blk_pc_cmnd to propagate the information into the command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Simplify handling of write same requests by setting up the command directly
instead of initializing request fields and then calling
scsi_setup_blk_pc_cmnd to propagate the information into the command.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Simplify handling of flush requests by setting up the command directly
instead of initializing request fields and then calling
scsi_setup_blk_pc_cmnd to propagate the information into the command.
Also rename scsi_setup_flush_cmnd to sd_setup_flush_cmnd for consistency.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The data direction fiel in the SCSI command is derived only from the block
request structure. Move setting it up into common code instead of
duplicating it in the ULDs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
We should call the device handler prep_fn for all TYPE_FS requests,
not just simple read/write calls that are handled by the disk driver.
Restructure the common I/O code to call the prep_fn handler and zero
out the CDB, and just leave the call to scsi_init_io to the ULDs.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
scsi_init_io should only be called for requests that transfer data,
so move the assert that a request has segments from the callers into
scsi_init_io.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
During IO with fabric faults, one generally sees several "Unhandled error
code" messages in the syslog as shown below:
sd 4:0:6:2: [sdbw] Unhandled error code
sd 4:0:6:2: [sdbw] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 4:0:6:2: [sdbw] CDB: Read(10): 28 00 00 00 00 00 00 00 08 00
end_request: I/O error, dev sdbw, sector 0
This comes from scsi_io_completion (in scsi_lib.c) while handling error
codes other than DID_RESET or not deferred sense keys i.e. this is
actually handled by the SCSI mid layer. But what gets displayed here is
"Unhandled error code" which is quite misleading as it indicates
something that is not addressed by the mid layer.
The description string is based on the sense key and sometimes on the
additional sense code;
since the ACTION_FAIL case always prints the sense key and the
additional sense code, this patch removes the description string
completely because it does not add useful information.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
While checking what scsi_adjust_queue_depth() did I thought its switch
statement could be clearer:
- remove redundant assignment (to sdev->queue_depth)
- re-order cases (thus removing the fall-through)
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that the ibmvstgt driver as the only user of scsi_tgt is gone, the
scsi_tgt kernel module, the CONFIG_SCSI_TGT, CONFIG_SCSI_SRP_TGT_ATTRS and
CONFIG_SCSI_FC_TGT_ATTRS kbuild variable, the scsi_host_template
transfer_response method are no longer needed.
[hch: minor updates to the current tree, changelog update]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Remove the libsrp module which was only used by the now removed ibmvstgt
driver.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
The IBM virtual SCSI protocol has been obsoleted by ibmvfc, and there
are no reported of the driver left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Using dev_printk variants prefixes the logging message with
the originating device, which makes debugging easier.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update the st driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update the ch driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update the sg driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Doug Gilbert <dgilbert@interlog.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Update the sr driver to use dev_printk() variants instead of
plain printk(); this will prefix logging messages with the
appropriate device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
scsilun_to_int() has an error which prevents it from generating
correct LUN numbers for 64bit values.
Also we should remove the misleading comment about portions of
the LUN being ignored; the initiator should treat the LUN as
an opaque value.
And, finally, the example given should use the correct
prefix (here: extended flat space addressing scheme).
This patch includes the modifications suggested by
Bart van Assche.
Cc: Bart van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: James Bottomley <jbottomley@parallels.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Now that we're using 64-bit LUNs internally we need to increase
the size of max_luns to 64 bits, too.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Older HBAs are only capable of supporting 16-bit LUNs,
so we need to make sure to adjust max_lun accordingly.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Chad Dupuis <chad.dupuis@qlogic.com>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Sequential scan for more than 256 LUNs is very fragile as
LUNs might not be numbered sequentially after that point.
SAM revisions later than SCSI-3 impose a structure on
LUNs larger than 256, making LUN numbers between 256
and 16384 illegal.
SCSI-3, however allows for plain 64-bit numbers with
no internal structure.
So restrict sequential LUN scan to 256 LUNs and add a
new blacklist flag 'BLIST_SCSI3LUN' to scan up to
max_lun devices.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Obsolete; either use 'max_lun' if the host supports only a
limited number of LUNs or BLIST_NOLUN if the target has
problems addressing more than one LUN.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This addresses a problem reported by Vaughan Cao concerning
the correctness of the O_EXCL logic in the sg driver. POSIX
doesn't defined O_EXCL semantics on devices but "allow only
one open file descriptor at a time per sg device" is a rough
definition. The sg driver's semantics have been to wait
on an open() when O_NONBLOCK is not given and there are
O_EXCL headwinds. Nasty things can happen during that wait
such as the device being detached (removed). So multiple
locks are reworked in this patch making it large and hard
to break down into digestible bits.
This patch is against Linus's current git repository which
doesn't include any sg patches sent in the last few weeks.
Hence this patch touches as little as possible that it
doesn't need to and strips out most SCSI_LOG_TIMEOUT()
changes in v3 because Hannes said he was going to rework all
that stuff.
The sg3_utils package has several test programs written to
test this patch. See examples/sg_tst_excl*.cpp .
Not all the locks and flags in sg have been re-worked in
this patch, notably sg_request::done . That can wait for
a follow-up patch if this one meets with approval.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
When the SG_IO ioctl was copied into the block layer and
later into the bsg driver, subtle differences emerged.
One difference is the way injected commands are queued through
the block layer (i.e. this is not SCSI device queueing nor SATA
NCQ). Summarizing:
- SG_IO in the block layer: blk_exec*(at_head=false)
- sg SG_IO: at_head=true
- bsg SG_IO: at_head=true
Some time ago Boaz Harrosh introduced a sg v4 flag called
BSG_FLAG_Q_AT_TAIL to override the bsg driver default.
This patch does the equivalent for the sg driver.
ChangeLog:
Introduce SG_FLAG_Q_AT_TAIL flag to cause commands
to be injected into the block layer with
at_head=false.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
- remove the 16 byte CDB (SCSI command) length limit from the sg driver
by handling longer CDBs the same way as the bsg driver. Remove comment
from sg.h public interface about the cmd_len field being limited to 16
bytes.
- remove some dead code caused by this change
- cleanup comment block at the top of sg.h, fix urls
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Until now the per-command transfer length has exclusively been gated by
the max_sectors parameter in the scsi_host template. Given that the size
of this parameter has been bumped to an unsigned int we have to be
careful not to exceed the target device's capabilities.
If the if the device specifies a Maximum Transfer Length in the Block
Limits VPD we'll use that value. Otherwise we'll use 0xffffffff for
devices that have use_16_for_rw set and 0xffff for the rest. We then
combine the chosen disk limit with max_sectors in the host template. The
smaller of the two will be used to set the max_hw_sectors queue limit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In init_sd function, if kmem_cache_create or mempool_create_slab_pools
calls fail, the error will not be correclty reported because
class_register previously set the value of err to 0.
Signed-off-by: Clément Calmels <clement.calmels@free.fr>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is a fix for commit 39c60a0948
"sd: fix array cache flushing bug causing performance problems"
We must notify the block layer via q->flush_flags after a temporary change
of the cache_type to write through. Without this, a SYNCHRONIZE CACHE
command will still be generated. This patch factors out a helper that
can be called from sd_revalidate_disk and cache_type_store.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change enables to test read/write commands with huge transfer
length such as 1GB. For example:
# modprobe scsi_debug dev_size_mb=1024 clustering=1 opts=1
# cat /sys/block/$DEV/queue/max_hw_sectors_kb > \
/sys/block/$DEV/queue/max_sectors_kb
# fio --name=test --rw=write --bs=1g --size=1g --filename=/dev/$DEV \
--mem=mmaphuge --direct=1
The data type of max_sectors in scsi_host_template has been extended
to unsigned int by the previous change. So we can increase it from
0xffff to 0xffffffff to allow such huge transfer length.
Also, this increases sg_tablesize and max_segment_size, otherwise the
maximum transfer length is limited to 64MB.
(sg_tablesize * max_segment_size = 256 * 256KB)
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This change makes the scsi disk driver handle the requests whose
transfer length is greater than 0xffff with READ_16 or WRITE_16.
However, this is a preparation for extending the data type of
max_sectors in struct Scsi_Host and scsi_host_template. So, it is
impossible to happen this condition for now, because SCSI low-level
drivers can not specify max_sectors greater than 0xffff due to the
data type limitation.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This prevents integer overflow when converting the request queue's
max_sectors from sectors to bytes. However, this is a preparation for
extending the data type of max_sectors in struct Scsi_Host and
scsi_host_template. So, it is impossible to happen this integer
overflow for now, because SCSI low-level drivers can not specify
max_sectors greater than 0xffff due to the data type limitation.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
scsi_put_command() is either invoked before blk_start_request() or
after block layer processing has completed. scsi_cmnd.abort_work
is scheduled from inside the SCSI timeout handler. The block layer
guarantees that either the regular completion handler
(softirq_done_fn()) or the timeout handler (rq_timed_out_fn()) is
invoked but not both. This means that scsi_put_command() is never
invoked while abort_work is scheduled. Hence remove the
cancel_delayed_work() call from scsi_put_command().
Similarly, scsi_abort_command() is only invoked from the SCSI
timeout handler. If scsi_abort_command() is invoked for a SCSI
command with the SCSI_EH_ABORT_SCHEDULED flag set this means that
scmd_eh_abort_handler() has already invoked scsi_queue_insert() and
hence that scsi_cmnd.abort_work is no longer pending. Hence also
remove the cancel_delayed_work() call from scsi_abort_command().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Flush commands don't transfer data and thus need to be special cased
in the I/O completion handler so that we can propagate errors to
the block layer and filesystem.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Steven Haber <steven@qumulo.com>
Tested-by: Steven Haber <steven@qumulo.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
This is a set of 13 fixes, a MAINTAINERS update and a sparse update. The
fixes are mostly correct value initialisations, avoiding NULL derefs and some
uninitialised pointer avoidance.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJTuNEhAAoJEDeqqVYsXL0MYC4H/2gpxHA9rELiqPRLJGNjt9v3
YlGrIwVAAdYLBSgwtkpAYj6oDJtwRmZvP3Saj2n5Lga+32mgFsPjvy+JsM3O41SL
k5QRlAs10wMbOB/dSoGxFsKdGnig4NolCIe5p0MGQvAbcCvh9z2Tr876ssvSfMCh
1mh0xmTCIutD7R2f5WjRckA+HZo+qmLLz5ZyogDasI3mSRAHjcZ+j5HdWBQbEsag
U6lPDR5VpUjGpigwJ+BPWwKTbIAIW1v2TB1YjWSHr5h2QPLBa+hfbyc15S1AjsGb
9F5/L432yk4UXQUKyKIpCKi8rDCoioM8dt8ofjjTNfNNjDlYRRHKutalef1yOw8=
=HPXQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of 13 fixes, a MAINTAINERS update and a sparse update.
The fixes are mostly correct value initialisations, avoiding NULL
derefs and some uninitialised pointer avoidance.
All the patches have been incubated in -next for a few days. The
final patch (use the scsi data buffer length to extract transfer size)
has been rebased to add a cc to stable, but only the commit message
has changed"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] use the scsi data buffer length to extract transfer size
virtio-scsi: fix various bad behavior on aborted requests
virtio-scsi: avoid cancelling uninitialized work items
ibmvscsi: Add memory barriers for send / receive
ibmvscsi: Abort init sequence during error recovery
qla2xxx: Fix sparse warning in qla_target.c.
bnx2fc: Improve stats update mechanism
bnx2fc: do not scan uninitialized lists in case of error.
fc: ensure scan_work isn't active when freeing fc_rport
pm8001: Fix potential null pointer dereference and memory leak.
MAINTAINERS: Update LSILOGIC MPT FUSION DRIVERS (FC/SAS/SPI) maintainers Email IDs
be2iscsi: remove potential junk pointer free
be2iscsi: add an missing goto in error path
scsi_error: set DID_TIME_OUT correctly
scsi_error: fix invalid setting of host byte
There's several locations in the kernel that open code the calculation
of the next location in the trace_seq buffer. This is usually done with
p->buffer + p->len
Instead of having this open coded, supply a helper function in the
header to do it for them. This function is called trace_seq_buffer_ptr().
Link: http://lkml.kernel.org/p/20140626220129.452783019@goodmis.org
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though the virtio-scsi spec guarantees that all requests related
to the TMF will have been completed by the time the TMF itself completes,
the request queue's callback might not have run yet. This causes requests
to be completed more than once, and as a result triggers a variety of
BUGs or oopses.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Calling the workqueue interface on uninitialized work items isn't a
good idea even if they're zeroed. It's not failing catastrophically only
through happy accidents.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a memory barrier prior to sending a new command to the VIOS
to ensure the VIOS does not receive stale data in the command buffer.
Also add a memory barrier when processing the CRQ for completed commands.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
If a CRQ reset is triggered for some reason while in the middle
of performing VSCSI adapter initialization, we don't want to
call the done function for the initialization MAD commands as
this will only result in two threads attempting initialization
at the same time, resulting in failures.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Signed-off-by: Christoph Hellwig <hch@lst.de>
Recently had this warning reported:
[ 290.489047] Call Trace:
[ 290.489053] [<ffffffff8169efec>] dump_stack+0x19/0x1b
[ 290.489055] [<ffffffff810ac7a9>] __might_sleep+0x179/0x230
[ 290.489057] [<ffffffff816a4ad5>] mutex_lock_nested+0x55/0x520
[ 290.489061] [<ffffffffa01b9905>] ? bnx2fc_l2_rcv_thread+0xc5/0x4c0 [bnx2fc]
[ 290.489065] [<ffffffffa0174c1a>] fc_vport_id_lookup+0x3a/0xa0 [libfc]
[ 290.489068] [<ffffffffa01b9a6c>] bnx2fc_l2_rcv_thread+0x22c/0x4c0 [bnx2fc]
[ 290.489070] [<ffffffffa01b9840>] ? bnx2fc_vport_destroy+0x110/0x110 [bnx2fc]
[ 290.489073] [<ffffffff8109e0cd>] kthread+0xed/0x100
[ 290.489075] [<ffffffff8109dfe0>] ? insert_kthread_work+0x80/0x80
[ 290.489077] [<ffffffff816b2fec>] ret_from_fork+0x7c/0xb0
[ 290.489078] [<ffffffff8109dfe0>] ? insert_kthread_work+0x80/0x80
Its due to the fact that we call a potentially sleeping function from the bnx2fc
rcv path with preemption disabled (via the get_cpu call embedded in the per-cpu
variable stats lookup in bnx2fc_l2_rcv_thread.
Easy enough fix, we can just move the stats collection later in the function
where we are sure we won't preempt or sleep. This also allows us to not have to
enable pre-emption when doing a per-cpu lookup, since we're certain not to get
rescheduled.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
In case of of error, the bnx2fc_cmd_mgr_alloc() function will call
the bnx2fc_cmd_mgr_free() to perform the cleanup.
The problem is that in one case the latter may try to scan
some not-yet initialized lists, resulting in a kernel panic.
This patch prevents this from happening by freeing the lists
before calling bnx2fc_cmd_mgr_free().
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
