* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
* pm-runtime:
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Runtime: Consistent utilization of deferred_resume
PM / Runtime: Prevent runtime_resume from racing with probe
PM / Runtime: Replace "run-time" with "runtime" in documentation
PM / Runtime: Improve documentation of enable, disable and barrier
PM: Limit race conditions between runtime PM and system sleep (v2)
PCI / PM: Detect early wakeup in pci_pm_prepare()
PM / Runtime: Return special error code if runtime PM is disabled
PM / Runtime: Update documentation of interactions with system sleep
Until these drivers are runtime PM converted, their device power
states are managed by calling custom driver hooks late in the
idle/suspend path. Therefore, do not let the suspend/resume core code
automatically idle these devices since they will be managed manually
by the OMAP PM core very late in the idle/suspend path.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If an ARM system has multiple cpus in the same socket and the
kernel is booted with maxcpus=1, secondary cpus are possible but
not present due to how platform_smp_prepare_cpus() is called.
Since most typical ARM processors don't actually support physical
hotplug, initialize the present map to be equal to the possible
map in generic ARM SMP code. Also, always call
platform_smp_prepare_cpus() as long as max_cpus is non-zero (0
means no SMP) to allow platform code to do any SMP setup.
After applying this patch it's possible to boot an ARM system
with maxcpus=1 on the command line and then hotplug in secondary
cpus via sysfs. This is more in line with how x86 does things.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pointers to statically declared platform device structures which are
registered with platform_device_register() are then used during run time
to access these structure members, for example from platform_uevent()
and much more. Therefore, these structures should never be placed inside
sections which are dropped after boot. Fix platform devices incorrectly
tagged with __initdata which happen to exist inside OMAP sub-trees.
This bug has exhibited itself on my ARM/OMAP1 based Amstrad Delta
videophone after commit 6d3163ce86, "mm:
check if any page in a pageblock is reserved before marking it
MIGRATE_RESERVE", resulting in reading from several
/sys/device/platform/*/uevent files always ending up with segmentation
faults.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Varadarajan, Charulatha <charu@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are SoCs where attempting to enter a low power state is ignored,
and the CPU continues executing instructions with all state preserved.
It is over-complex at that point to disable the MMU just to call the
resume path.
Instead, allow the suspend finisher to return error codes to abort
suspend in this circumstance, where the cpu_suspend internals will then
unwind the saved state on the stack. Also omit the tlb flush as no
changes to the page tables will have happened.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the saving of the auxiliary control registers into C; there's
no need for this to be in assembly code. This results in less
assembly code to deal with in OMAP.
Kevin tested full-chip retention and off on 3430/n900, 3530/Overo and
3630/Zoom3.
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of the ASM sleep code (in arch/arm/mach-omap2/sleep34xx.S)
is copied to internal SRAM at boot and after wake-up from CORE OFF
mode. However only a small part of the code really needs to run from
internal SRAM.
This fix lets most of the ASM idle code run from the DDR in order to
minimize the SRAM usage and the overhead in the code copy.
The only pieces of code that are mandatory in SRAM are:
- the i443 erratum WA,
- the i581 erratum WA,
- the security extension code.
SRAM usage:
- original code:
. 560 bytes for omap3_sram_configure_core_dpll (used by DVFS),
. 852 bytes for omap_sram_idle (used by suspend/resume in RETention),
. 124 bytes for es3_sdrc_fix (used by suspend/resume in OFF mode on ES3.x),
. 108 bytes for save_secure_ram_context (used on HS parts only).
With this fix the usage for suspend/resume in RETention goes down 288
bytes, so the gain in SRAM usage for suspend/resume is 564 bytes.
Also fixed the SRAM initialization sequence to avoid an unnecessary
copy to SRAM at boot time and for readability.
Tested on Beagleboard (ES2.x) in idle with full RET and OFF modes.
Kevin Hilman tested retention and off on 3430/n900, 3530/Overo and
3630/Zoom3
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Platforms provide an empty irq_prio_table macro, and as nothing uses
this macro, it can simply be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The first and second arguments shouldn't concern platform code, so
hide them from each platforms caller.
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Upon return from off-mode, the ROM code jumps to a restore function
saved in the scratchpad. Based on SoC revision or errata, this
restore entry point is different. Current code uses some helper
functions in sleep34xx.S (get_*_restore_pointer) to get the restore
function entry point.
When returning from off-mode, this code is executed from SDRAM, so
there's no reason to use these helper functions when using the SDRAM
entry points directly would work just fine.
This patch uses ENTRY/ENDPROC to create "real" entry points for these
functions, and uses those values directly when writing the scratchpad.
Tested all three entry points
- restore_es3: 3430/n900
- restore_3630: 3630/Zoom3
- restore: 3530/Overo
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert omap34xx to use the generic CPU suspend/resume support, rather
than implementing its own version. Tested on 3430 LDP.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code alludes to r9 being used to indicate what was lost over the
suspend/resume transition. However, although r9 is set, it is never
actually used.
Also, the comments before the code (which refer to the value of r9)
and the comments against the assignment of r9 contradict each other,
so just remove them to avoid confusion.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ABI allows called functions to corrupt r0-r3 and ip (r12). So
its pointless saving these registers in the suspend code - the
calling function will expect them to be corrupted and so won't rely
on their contents after resume.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove cpu_is_* checks from gpio_show_revision() by passing in the
revision address offset from platform data. SoCs with no revision
register (15xx, 7xx, and all MPUIOs) use -1 (actually, USHRT_MAX) to
signify no register.
While here, all GPIO banks are assumed to be the same revision, so fix
show_revision() to only show the revision for the first bank it finds.
This removes duplicate GPIO revision prints during boot.
Thanks to Charulatha V <charu@ti.com> for finding/fixing a few -1s
that were missed in the original patch.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup GPIO IRQ enable/disable handling by removing SoC-specific
Also split enable/disable IRQ into separate functions for better
readability and also facilitate potentially moving to generic irq_chip
in the future.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Cleanup IRQ status handling by passing IRQ status register offsets
via platform data.
Cleans up clearing of GPIO IRQ status and GPIO ISR handler.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offset fields to GPIO platform_data for registers.
This patch adds registers that control direction, input and output
data. Using these register offsets in the common driver allows
removal of #ifdefs and greatly improves readability.
Also create dedicated data out functions: one for banks with dedicated
set/clear registers, and another for banks with a single mask
register.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Commit d5ce2b65 "omap3630: nand: fix device size to work in polled mode"
changed values for .devsize in nand platform data, now we have to pass
NAND_BUSWIDTH_16 instead of '1' to select 16bit NAND.
Update pandora's platform data accordingly, also specify appropriate
transfer type.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x423c): Section mismatch in reference from the function pm_dbg_regset_init() to the function .init.text:pm_dbg_init()
The function pm_dbg_regset_init() references
the function __init pm_dbg_init().
This is often because pm_dbg_regset_init lacks a __init
annotation or the annotation of pm_dbg_init is wrong.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
4 micro seconds is not enough for PBIAS if MMC regulator is
enabled from MMC regulator OFF.
Increase the delay for PBIAS to stabilize.
Wait for PBIAS and timeout if not.
Resolves MMC/SD failure on OMAP4
"Pbias Voltage is not same as LDO"
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Several boards defining mtd partitions also defined NAND_BLOCK_SIZE as
SZ_128K. Move the define to common-board-devices.h
This removes multiple defines of NAND_BLOCK_SIZE.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 407a6888f7 (OMAP4: hwmod data:
Add AESS, McPDM, bandgap, counter_32k, MMC, KBD, ISS & IPU) added the
entry for keypad, but did not enable it.
Enable the keypad in the hwmod database so it works.
Signed-off-by: Shubhrajyoti D<shubhrajyoti@ti.com>
Acked-by: Benoit Cousson<b-cousson@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Free Beagle rev gpios when they are read, so others can read them later
Signed-off-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without msecure beeing high it isn't possible to set (or start)
the RTC.
Tested with a BeagleBoard C4.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Speaker amplifier is accidentally powered up in early TWL gpio setup. This
causes a few mA of needless battery current consumption. Without this patch
the amplifier can be shutdown only by having one active audio playback and
shutdown cycle to speaker output.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The V28_A domain in Nokia N900 that supplies VDD voltages to TLV320AIC34 and
TPA6130A2 should not be shutdown. This is because otherwise there will be
leak from VIO to VDD in TLV320AIC34 and this leak consumes more battery
current that is saved from keeping V28_A off. With this patch the battery
current consumption is approximately 1.5 mA lower.
Thanks to Kalle Jokiniemi <kalle.jokiniemi@nokia.com> for noticing the issue.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Kalle Jokiniemi <kalle.jokiniemi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
introduced by: 96974a24
(omap: consolidate touch screen initialization among different boards)
ads7846 driver can use either gpio_pendown or get_pendown_state()
callback. In case of gpio_pendown, it requests the provided gpio_pendown
thus resulting in double requesting that gpio:
ads7846 spi1.0: failed to request pendown GPIO57
ads7846: probe of spi1.0 failed with error -16
Fix this by restricting the gpio request to the case of
get_pendown_state() callback is used.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 contains two separate instances of the padconf registers,
one in the core system config and one in the wakeup system config.
Pass in two tables to apply the correct values to each instance.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has two mux instances, and the board may not have settings
for one of them. Allow the board file to pass NULL for an
instance's mux settings, which will initialize the mux instance
but skip writing board settings.
Signed-off-by: Colin Cross <ccross@android.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't PTR_ERR() a non-error pointer:
initcall omap4_l3_init+0x0/0xdc returned -544980480 after 0 usecs
initcall omap4_l3_init+0x0/0xdc returned with error code -544980480
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix below compilation warnings.
arch/arm/mach-omap2/omap_hwmod.c: In function 'omap_hwmod_for_each':
arch/arm/mach-omap2/omap_hwmod.c:1631: warning: 'ret' may be used uninitialized in this function
arch/arm/mach-omap2/mux.c: In function 'omap_mux_get_gpio':
arch/arm/mach-omap2/mux.c:917: warning: 'm' may be used uninitialized in this function
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
WARNING: arch/arm/mach-omap2/built-in.o(.text+0x11014): Section mismatch
in reference from the function cm_t3517_init_usbh() to the (unknown
reference) .init.data:(unknown)
The function cm_t3517_init_usbh() references
the (unknown reference) __initdata (unknown).
This is often because cm_t3517_init_usbh lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The serial*_data should have been marked as __initdata as per
it's usage in the board files. Fix the same to remove the
section mismatch warnings caused by it.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Silesh C V <silesh@ti.com>
[tony@atomide.com: updated with additional fixes from Silesh]
Signed-off-by: Tony Lindgren <tony@atomide.com>
I got some build error like below while executing "make omap2plus_defconfig".
CC arch/arm/mach-omap2/board-2430sdp.o
arch/arm/mach-omap2/board-2430sdp.c: In function 'omap_2430sdp_init':
arch/arm/mach-omap2/board-2430sdp.c:247: error: 'GPIOF_OUT_INIT_LOW' undeclared (first use in this function)
arch/arm/mach-omap2/board-2430sdp.c:247: error: (Each undeclared identifier is reported only once
arch/arm/mach-omap2/board-2430sdp.c:247: error: for each function it appears in.)
This patch fixes the build error by include linux/gpio.h instead of mach/gpio.h.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Syed Mohammed Khasim <x0khasim@ti.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* git://git.infradead.org/battery-2.6:
PXA: Use dev_pm_ops in z2_battery
ds2760_battery: Fix rated capacity of the hx4700 1800mAh battery
ds2760_battery: Fix indexing of the 4 active full EEPROM registers
power: Make test_power driver more dynamic.
bq27x00_battery: Name of cycle count property
max8903_charger: Add GENERIC_HARDIRQS as a dependency (fixes S390 build)
ARM: RX-51: Enable isp1704 power on/off
isp1704_charger: Allow board specific powering routine
gpio-charger: Add gpio_charger_resume
power_supply: Add driver for MAX8903 charger
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (57 commits)
regulator: Fix 88pm8607.c printk format warning
input: Add support for Qualcomm PMIC8XXX power key
input: Add Qualcomm pm8xxx keypad controller driver
mfd: Add omap-usbhs runtime PM support
mfd: Fix ASIC3 SD Host Controller Configuration size
mfd: Fix omap_usbhs_alloc_children error handling
mfd: Fix omap usbhs crash when rmmoding ehci or ohci
mfd: Add ASIC3 LED support
leds: Add ASIC3 LED support
mfd: Update twl4030-code maintainer e-mail address
mfd: Correct the name and bitmask for ab8500-gpadc BTempPullUp
mfd: Add manual ab8500-gpadc batt temp activation for AB8500 3.0
mfd: Provide ab8500-core enumerators for chip cuts
mfd: Check twl4030-power remove script error condition after i2cwrite
mfd: Fix twl6030 irq definitions
mfd: Add phoenix lite (twl6025) support to twl6030
mfd: Avoid to use constraint name in 88pm860x regulator driver
mfd: Remove checking on max8925 regulator[0]
mfd: Remove unused parameter from 88pm860x API
mfd: Avoid to allocate 88pm860x static platform data
...
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
OMAP3: PM: Boot message is not an error, and not helpful, remove it
OMAP3: cpuidle: change the power domains modes determination logic
OMAP3: cpuidle: code rework for improved readability
OMAP3: cpuidle: re-organize the C-states data
OMAP3: clean-up mach specific cpuidle data structures
OMAP3 cpuidle: remove useless SDP specific timings
usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
usb: otg: OMAP4430: Fixing the omap4430_phy_init function
usb: musb: am35x: fix compile error when building am35x
usb: musb: OMAP4430: Power down the PHY during board init
omap: drop board-igep0030.c
omap: igep0020: add support for IGEP3
omap: igep0020: minor refactoring
omap: igep0020: name refactoring for future merge with IGEP3
omap: Remove support for omap2evm
arm: omap2plus: GPIO cleanup
omap: musb: introduce default board config
omap: move detection of NAND CS to common-board-devices
omap: use common initialization for PMIC i2c bus
omap: consolidate touch screen initialization among different boards
...
Modifying the macro name Main_Ref to all caps(MAIN_REF).
Suggested by Nishanth Menon <nm@ti.com>
Signed-off-by: Lesly A M <leslyam@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
