The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) nft_compat accidently truncates ethernet protocol to 8-bits, from
Arturo Borrero.
2) Memory leak in ip_vs_proc_conn(), from Julian Anastasov.
3) Don't allow the space required for nftables rules to exceed the
maximum value representable in the dlen field. From Patrick
McHardy.
4) bcm63xx_enet can accidently leave interrupts permanently disabled
due to errors in the NAPI polling exit logic. Fix from Nicolas
Schichan.
5) Fix OOPSes triggerable by the ping protocol module, due to missing
address family validations etc. From Lorenzo Colitti.
6) Don't use RCU locking in sleepable context in team driver, from Jiri
Pirko.
7) xen-netback miscalculates statistic offset pointers when reporting
the stats to userspace. From David Vrabel.
8) Fix a leak of up to 256 pages per VIF destroy in xen-netaback, also
from David Vrabel.
9) ip_check_defrag() cannot assume that skb_network_offset(),
particularly when it is used by the AF_PACKET fanout defrag code.
From Alexander Drozdov.
10) gianfar driver doesn't query OF node names properly when trying to
determine the number of hw queues available. Fix it to explicitly
check for OF nodes named queue-group. From Tobias Waldekranz.
11) MID field in macb driver should be 12 bits, not 16. From Punnaiah
Choudary Kalluri.
12) Fix unintentional regression in traceroute due to timestamp socket
option changes. Empty ICMP payloads should be allowed in
non-timestamp cases. From Willem de Bruijn.
13) When devices are unregistered, we have to get rid of AF_PACKET
multicast list entries that point to it via ifindex. Fix from
Francesco Ruggeri.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
tipc: fix bug in link failover handling
net: delete stale packet_mclist entries
net: macb: constify macb configuration data
MAINTAINERS: add Marc Kleine-Budde as co maintainer for CAN networking layer
MAINTAINERS: linux-can moved to github
can: kvaser_usb: Read all messages in a bulk-in URB buffer
can: kvaser_usb: Avoid double free on URB submission failures
can: peak_usb: fix missing ctrlmode_ init for every dev
can: add missing initialisations in CAN related skbuffs
ip: fix error queue empty skb handling
bgmac: Clean warning messages
tcp: align tcp_xmit_size_goal() on tcp_tso_autosize()
net: fec: fix unbalanced clk disable on driver unbind
net: macb: Correct the MID field length value
net: gianfar: correctly determine the number of queue groups
ipv4: ip_check_defrag should not assume that skb_network_offset is zero
net: bcmgenet: properly disable password matching
net: eth: xgene: fix booting with devicetree
bnx2x: Force fundamental reset for EEH recovery
xen-netback: refactor xenvif_handle_frag_list()
...
Add missing "cdns,at91sam9260-macb", "atmel,sama5d3-gem" and
"atmel,sama5d4-gem" compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove reference to obsolete ifconfig command.
MTU can be changed with ip command instead.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other serial
driver bugfixes as well. Most notable is a wait_until_sent bugfix that
was traced back to being around since before 2.6.12 that Johan has fixed
up.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlT8RCYACgkQMUfUDdst+yk62QCgycxS4giC2hyRver3dyvaNR6g
zYYAn2w0uRndW+AqP4Tls54isRz6owpF
=gA2k
-----END PGP SIGNATURE-----
Merge tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for 4.0-rc3.
Along with the atime fix that you know about, here are some other
serial driver bugfixes as well. Most notable is a wait_until_sent
bugfix that was traced back to being around since before 2.6.12 that
Johan has fixed up.
All have been in linux-next successfully"
* tag 'tty-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
TTY: fix tty_wait_until_sent maximum timeout
TTY: fix tty_wait_until_sent on 64-bit machines
USB: serial: fix infinite wait_until_sent timeout
TTY: bfin_jtag_comm: remove incorrect wait_until_sent operation
net: irda: fix wait_until_sent poll timeout
serial: uapi: Declare all userspace-visible io types
serial: core: Fix iotype userspace breakage
serial: sprd: Fix missing spin_unlock in sprd_handle_irq()
console: Fix console name size mismatch
tty: fix up atime/mtime mess, take four
serial: 8250_dw: Fix get_mctrl behaviour
serial:8250:8250_pci: delete unneeded quirk entries
serial:8250:8250_pci: fix redundant entry report for WCH_CH352_2S
Change email address for 8250_pci
serial: 8250: Revert "tty: serial: 8250_core: read only RX if there is something in the FIFO"
Revert "tty/serial: of_serial: add DT alias ID handling"
This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTwygoACgkQMUfUDdst+yk8ZQCdFYB9t3ZIzxiobR1pQy/PJ6Ld
dxEAnRrKzKn1FaJKCkHg35YrInKVwScZ
=tRWZ
-----END PGP SIGNATURE-----
Merge tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull "code of conflict" from Greg KH:
"This file tries to set the rational basis for our code reviews, gives
some advice on how to conduct them, and provides an excalation channel
for any kernel developers if they so desire it"
[ Let's see how this works ]
* tag 'cc-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Code of Conflict
Pull i2c fixes from Wolfram Sang:
"A set of updates and bugfixes for the new designware-baytrail driver.
And a documentation bugfix"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: imx: add required clocks property to binding
i2c: designware-baytrail: baytrail_i2c_acquire() might sleep
i2c: designware-baytrail: cross-check lock functions
i2c: designware-baytrail: fix sparse warnings
i2c: designware-baytrail: fix typo in error path
i2c: designware-baytrail: describe magic numbers
Fixed behaviour of get_mctrl() serial driver function as documented in:
https://www.kernel.org/doc/Documentation/serial/driver
Added device-tree properties 'dcd-override', 'dsr-override',
'cts-override', and 'ri-override' specific to the Synopsis 8250
DesignWare UART driver. Allows one to force Data Carrier Detect,
Clear To Send, and Data Set Ready signals to permanently be reported as
active. The Ring indicator can be forced to be reported as inactive.
It is possible that if modem control signalling is enabled on a port
that doesn't have these pins (e.g. - a simple two wire Tx/Rx port), the
driver can hang indefinitely waiting for the state to change. The new
DT properties allow the driver to ignore the state of these pins on
serial ports that don't support them, as recommended in the kernel
documentation.
Reviewed-by: JD (Jiandong) Zheng <jdzheng@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A clock specifier is required for i.MX I2C and is
provided in all DTS implementations. Add this to the
list of required properties in the binding.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Namely tcp_probe_interval to control how often to restart
a probe. And tcp_probe_threshold to control when stop the
probing in respect to the width of search range in bytes
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while
at it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to
an unexpected combination of interrupt action handler flags.
However, on at91 a timer IRQ is shared with some other devices
(including system wakeup ones) and that leads to the unusual
combination of flags in question. To make it possible to avoid
the warning introduce a new interrupt action handler flag (which
can be used by drivers to indicate the special case to the core)
and rework the problematic at91 drivers to use it and work as
expected during system suspend/resume. From Boris Brezillon,
Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nc5T
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These are fixes for recent regressions (ACPI resources management,
suspend-to-idle), stable-candidate fixes (ACPI backlight), fixes
related to the wakeup IRQ management changes made in v3.18, other
fixes (suspend-to-idle, cpufreq ppc driver) and a couple of cleanups
(suspend-to-idle, generic power domains, ACPI backlight).
Specifics:
- Fix ACPI resources management problems introduced by the recent
rework of the code in question (Jiang Liu) and a build issue
introduced by those changes (Joachim Nilsson).
- Fix a recent suspend-to-idle regression on systems where entering
idle states causes local timers to stop, prevent suspend-to-idle
from crashing in restricted configurations (no cpuidle driver,
cpuidle disabled etc.) and clean up the idle loop somewhat while at
it (Rafael J Wysocki).
- Fix build problem in the cpufreq ppc driver (Geert Uytterhoeven).
- Allow the ACPI backlight driver module to be loaded if ACPI is
disabled which helps the i915 driver in those configurations
(stable-candidate) and change the code to help debug unusual use
cases (Chris Wilson).
- Wakeup IRQ management changes in v3.18 caused some drivers on the
at91 platform to trigger a warning from the IRQ core related to an
unexpected combination of interrupt action handler flags. However,
on at91 a timer IRQ is shared with some other devices (including
system wakeup ones) and that leads to the unusual combination of
flags in question.
To make it possible to avoid the warning introduce a new interrupt
action handler flag (which can be used by drivers to indicate the
special case to the core) and rework the problematic at91 drivers
to use it and work as expected during system suspend/resume. From
Boris Brezillon, Rafael J Wysocki and Mark Rutland.
- Clean up the generic power domains subsystem's debugfs interface
(Kevin Hilman)"
* tag 'pm+acpi-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
genirq / PM: describe IRQF_COND_SUSPEND
tty: serial: atmel: rework interrupt and wakeup handling
watchdog: at91sam9: request the irq with IRQF_NO_SUSPEND
cpuidle / sleep: Use broadcast timer for states that stop local timer
clk: at91: implement suspend/resume for the PMC irqchip
rtc: at91rm9200: rework wakeup and interrupt handling
rtc: at91sam9: rework wakeup and interrupt handling
PM / wakeup: export pm_system_wakeup symbol
genirq / PM: Add flag for shared NO_SUSPEND interrupt lines
ACPI / video: Propagate the error code for acpi_video_register
ACPI / video: Load the module even if ACPI is disabled
PM / Domains: cleanup: rename gpd -> genpd in debugfs interface
cpufreq: ppc: Add missing #include <asm/smp.h>
x86/PCI/ACPI: Relax ACPI resource descriptor checks to work around BIOS bugs
x86/PCI/ACPI: Ignore resources consumed by host bridge itself
cpuidle: Clean up fallback handling in cpuidle_idle_call()
cpuidle / sleep: Do sanity checks in cpuidle_enter_freeze() too
idle / sleep: Avoid excessive disabling and enabling interrupts
PCI: versatile: Update for list_for_each_entry() API change
genirq / PM: better describe IRQF_NO_SUSPEND semantics
With certain restrictions it is possible for a wakeup device to share
an IRQ with an IRQF_NO_SUSPEND user, and the warnings introduced by
commit cab303be91 are spurious. The new
IRQF_COND_SUSPEND flag allows drivers to tell the core when these
restrictions are met, allowing spurious warnings to be silenced.
This patch documents how IRQF_COND_SUSPEND is expected to be used,
updating some of the text now made invalid by its addition.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This sysctl gives two benefits. By defaulting the table size to 0
mpls even when compiled in and enabled defaults to not forwarding
any packets. This prevents unpleasant surprises for users.
The other benefit is that as mpls labels are allocated locally a dense
table a small dense label table may be used which saves memory and
is extremely simple and efficient to implement.
This sysctl allows userspace to choose the restrictions on the label
table size userspace applications need to cope with.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) If an IPVS tunnel is created with a mixed-family destination
address, it cannot be removed. Fix from Alexey Andriyanov.
2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
Neira Ayuso.
3) Generic statistics infrastructure can reference variables sitting on
a released function stack, therefore use dynamic allocation always.
Fix from Ignacy Gawędzki.
4) skb_copy_bits() return value test is inverted in ip_check_defrag().
5) Fix network namespace exit in openvswitch, we have to release all of
the per-net vports. From Pravin B Shelar.
6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.
7) Fix rhashtable grow/shrink behavior, only expand during inserts and
shrink during deletes. From Daniel Borkmann.
8) Netdevice names with semicolons should never be allowed, because
they serve as a separator. From Matthew Thode.
9) Use {,__}set_current_state() where appropriate, from Fabian
Frederick.
10) Revert byte queue limits support in r8169 driver, it's causing
regressions we can't figure out.
11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
measure packets in flight, properly use tcp_packets_in_flight()
instead. From Neal Cardwell.
12) Fix accidental removal of support for bluetooth in CSR based Intel
wireless cards. From Marcel Holtmann.
13) We accidently added a behavioral change between native and compat
tasks, wrt testing the MSG_CMSG_COMPAT bit. Just ignore it if the
user happened to set it in a native binary as that was always the
behavior we had. From Catalin Marinas.
14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
handling, from Bob Copeland.
15) Fix stale ->radar_required setting in mac80211 that can prevent
starting new scans, from Eliad Peller.
16) Fix memory leak in nl80211 monitor, from Johannes Berg.
17) Fix race in TX index handling in xen-netback, from David Vrabel.
18) Don't enable interrupts in amx-xgbe driver until all software et al.
state is ready for the interrupt handler to run. From Thomas
Lendacky.
19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
W Biederman.
20) The amount of header space needed in macvtap was not calculated
properly, fix it otherwise we splat past the beginning of the
packet. From Eric Dumazet.
21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.
22) Don't raw initialize or mod timers, use setup_timer() and
mod_timer() instead. From Vaishali Thakkar.
23) Fix software maintained statistics in bcmgenet and systemport
drivers, from Florian Fainelli.
24) DMA descriptor updates in sh_eth need proper memory barriers, from
Ben Hutchings.
25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
Kubecek.
26) Openvswitch's non-masked set actions aren't constructed properly
into netlink messages, fix from Joe Stringer.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
openvswitch: Fix serialization of non-masked set actions.
gianfar: Reduce logging noise seen due to phy polling if link is down
ibmveth: Add function to enable live MAC address changes
net: bridge: add compile-time assert for cb struct size
udp: only allow UFO for packets from SOCK_DGRAM sockets
sh_eth: Really fix padding of short frames on TX
Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
sh_eth: Ensure proper ordering of descriptor active bit write/read
net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
net/mlx4_core: Fix wrong mask and error flow for the update-qp command
net: systemport: fix software maintained statistics
net: bcmgenet: fix software maintained statistics
rxrpc: don't multiply with HZ twice
rxrpc: terminate retrans loop when sending of skb fails
net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
net: pasemi: Use setup_timer and mod_timer
net: stmmac: Use setup_timer and mod_timer
net: 8390: axnet_cs: Use setup_timer and mod_timer
net: 8390: pcnet_cs: Use setup_timer and mod_timer
...
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A small batch with accumulated updates in nf-next, mostly IPVS updates,
they are:
1) Add 64-bits stats counters to IPVS, from Julian Anastasov.
2) Move NETFILTER_XT_MATCH_ADDRTYPE out of NETFILTER_ADVANCED as docker
seem to require this, from Anton Blanchard.
3) Use boolean instead of numeric value in set_match_v*(), from
coccinelle via Fengguang Wu.
4) Allows rescheduling of new connections in IPVS when port reuse is
detected, from Marcelo Ricardo Leitner.
5) Add missing bits to support arptables extensions from nft_compat,
from Arturo Borrero.
Patrick is preparing a large batch to enhance the set infrastructure,
named expressions among other things, that should follow up soon after
this batch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-02
Here's the first bluetooth-next pull request targeting the 4.1 kernel:
- ieee802154/6lowpan cleanups
- SCO routing to host interface support for the btmrvl driver
- AMP code cleanups
- Fixes to AMP HCI init sequence
- Refactoring of the HCI callback mechanism
- Added shutdown routine for Intel controllers in the btusb driver
- New config option to enable/disable Bluetooth debugfs information
- Fix for early data reception on L2CAP fixed channels
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The memcg control knobs indicate the highest possible value using the
symbolic name "infinity", which is long and awkward to type.
Switch to the string "max", which is just as descriptive but shorter and
sweeter.
This changes a user interface, so do it before the release and before
the development flag is dropped from the default hierarchy.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Tejun Heo <tj@kernel.org>
Cc: Vladimir Davydov <vdavydov@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We (the Ocfs2 project) recently moved the location of our ocfs2-tools
git tree and project web page. The pertinent discussion can be seen
here:
https://oss.oracle.com/pipermail/ocfs2-devel/2015-February/010579.html
The following patch updates the Ocfs2 documentation in MAINTAINERS,
ocfs2.txt, and dlmfs.txt. I added our new official web page, changed
the location of our tools git tree and removed the link to Joel's
ancient kernel git tree - Andrew has handled our patches for a while
now.
Signed-off-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This file provides a basic guide for how to handle conflict resolution
when it comes up in the development process.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Arjan van de Ven <arjanvandeven@gmail.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Chris Ball <chris@printf.net>
Acked-by: Chris Mason <clm@fb.com>
Acked-by: Chris Metcalf <cmetcalf@ezchip.com>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Dave Airlie <airlied@redhat.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Acked-by: Josh Triplett <josh@joshtriplett.org>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Acked-by: NeilBrown <neilb@suse.de>
Acked-by: Olof Johansson <olof@lixom.net>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Sachin Prabhu <sprabhu@redhat.com>
Acked-by: Shuah Khan <shuahkh@osg.samsung.com>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Willy Tarreau <w@1wt.eu>
Acked-by: Zefan Li <lizefan@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While testing I experience a deadlock while using the at86rf233 on a
raspberry pi. The reason was an edge triggered gpio irq because the irq
triggered while irq was disabled. This issue doesn't happend on a level
triggered irq because the irq will hit after calling enable_irq.
This patch adds a warning that it's not recommended to use a edge-triggered
irq type. Also change the examples to high-level irqtype.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds support for setting the xtal trim register. Some at86rf2xx
transceiver boards needs fine tuning the xtal capacitor.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The IRQF_NO_SUSPEND flag is intended to be used for interrupts required
to be enabled during the suspend-resume cycle. This mostly consists of
IPIs and timer interrupts, potentially including chained irqchip
interrupts if these are necessary to handle timers or IPIs. If an
interrupt does not fall into one of the aforementioned categories,
requesting it with IRQF_NO_SUSPEND is likely incorrect.
Using IRQF_NO_SUSPEND does not guarantee that the interrupt can wake the
system from a suspended state. For an interrupt to be able to trigger a
wakeup, it may be necessary to program various components of the system.
In these cases it is necessary to use {enable,disabled}_irq_wake.
Unfortunately, several drivers assume that IRQF_NO_SUSPEND ensures that
an IRQ can wake up the system, and the documentation can be read
ambiguously w.r.t. this property.
This patch updates the documentation regarding IRQF_NO_SUSPEND to make
this caveat explicit, hopefully making future misuse rarer. Cleanup of
existing misuse will occur as part of later patch series.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PHY requires different settings for the Decision Feedback Analyzer
(DFE) when running in KX mode vs. KR mode. Update the code to change
these settings when changing modes in order to provide a more stable
link.
Additionally, adjust the 10GbE PQ skew default setting to a more sane
value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when TCP/SCTP port reusing happens, IPVS will find the old
entry and use it for the new one, behaving like a forced persistence.
But if you consider a cluster with a heavy load of small connections,
such reuse will happen often and may lead to a not optimal load
balancing and might prevent a new node from getting a fair load.
This patch introduces a new sysctl, conn_reuse_mode, that allows
controlling how to proceed when port reuse is detected. The default
value will allow rescheduling of new connections only if the old entry
was in TIME_WAIT state for TCP or CLOSED for SCTP.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Drop the '.o' suffix so this text properly covers both the
built-in and modular cases.
'insmod pktgen' obviously won't work; the command should be modprobe.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are Robert Olsson's samples which used to be available from
<ftp://robur.slu.se/pub/Linux/net-development/pktgen-testing/examples/>
but currently are not.
Change the documentation to refer to these consistently as 'sample
scripts', matching the directory name used here.
Cc: Robert Olsson <robert@herjulf.se>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thanks to Rob Jones for suggesting some of the changes.
Cc: Rob Jones <rob.jones@codethink.co.uk>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has been updated quite a few times since 2004, and git can
keep track of the actual date for us.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more vfs updates from Al Viro:
"Assorted stuff from this cycle. The big ones here are multilayer
overlayfs from Miklos and beginning of sorting ->d_inode accesses out
from David"
* 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (51 commits)
autofs4 copy_dev_ioctl(): keep the value of ->size we'd used for allocation
procfs: fix race between symlink removals and traversals
debugfs: leave freeing a symlink body until inode eviction
Documentation/filesystems/Locking: ->get_sb() is long gone
trylock_super(): replacement for grab_super_passive()
fanotify: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
Cachefiles: Fix up scripted S_ISDIR/S_ISREG/S_ISLNK conversions
VFS: (Scripted) Convert S_ISLNK/DIR/REG(dentry->d_inode) to d_is_*(dentry)
SELinux: Use d_is_positive() rather than testing dentry->d_inode
Smack: Use d_is_positive() rather than testing dentry->d_inode
TOMOYO: Use d_is_dir() rather than d_inode and S_ISDIR()
Apparmor: Use d_is_positive/negative() rather than testing dentry->d_inode
Apparmor: mediated_filesystem() should use dentry->d_sb not inode->i_sb
VFS: Split DCACHE_FILE_TYPE into regular and special types
VFS: Add a fallthrough flag for marking virtual dentries
VFS: Add a whiteout dentry type
VFS: Introduce inode-getting helpers for layered/unioned fs environments
Infiniband: Fix potential NULL d_inode dereference
posix_acl: fix reference leaks in posix_acl_create
autofs4: Wrong format for printing dentry
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS:
- a number of fixes that didn't make the 3.19 release.
- a number of cleanups.
- preliminary support for Cavium's Octeon 3 SOCs which feature up to
48 MIPS64 R3 cores with FPU and hardware virtualization.
- support for MIPS R6 processors.
Revision 6 of the MIPS architecture is a major revision of the MIPS
architecture which does away with many of original sins of the
architecture such as branch delay slots. This and other changes in
R6 require major changes throughout the entire MIPS core
architecture code and make up for the lion share of this pull
request.
- finally some preparatory work for eXtendend Physical Address
support, which allows support of up to 40 bit of physical address
space on 32 bit processors"
[ Ahh, MIPS can't leave the PAE brain damage alone. It's like
every CPU architect has to make that mistake, but pee in the snow
by changing the TLA. But whether it's called PAE, LPAE or XPA,
it's horrid crud - Linus ]
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (114 commits)
MIPS: sead3: Corrected get_c0_perfcount_int
MIPS: mm: Remove dead macro definitions
MIPS: OCTEON: irq: add CIB and other fixes
MIPS: OCTEON: Don't do acknowledge operations for level triggered irqs.
MIPS: OCTEON: More OCTEONIII support
MIPS: OCTEON: Remove setting of processor specific CVMCTL icache bits.
MIPS: OCTEON: Core-15169 Workaround and general CVMSEG cleanup.
MIPS: OCTEON: Update octeon-model.h code for new SoCs.
MIPS: OCTEON: Implement DCache errata workaround for all CN6XXX
MIPS: OCTEON: Add little-endian support to asm/octeon/octeon.h
MIPS: OCTEON: Implement the core-16057 workaround
MIPS: OCTEON: Delete unused COP2 saving code
MIPS: OCTEON: Use correct instruction to read 64-bit COP0 register
MIPS: OCTEON: Save and restore CP2 SHA3 state
MIPS: OCTEON: Fix FP context save.
MIPS: OCTEON: Save/Restore wider multiply registers in OCTEON III CPUs
MIPS: boot: Provide more uImage options
MIPS: Remove unneeded #ifdef __KERNEL__ from asm/processor.h
MIPS: ip22-gio: Remove legacy suspend/resume support
mips: pci: Add ifdef around pci_proc_domain
...
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU51MsAAoJEMUj8QotnQNan8wH/3Oa2/ofbX8zNYtdDxFBK7W0
pHwVA2CH9yzDDi90X9GsQODmXerMrYf+SHo/RsQTpSnt5WI/4ZVP/1EoNGu6T2Yr
XiaKc/Jwo+ScxdhoHSNtyGL5vKeipX6clgz1wcd/4/UBcBAr0Vxj25s8Ta7naK2V
hZyWnt3MCGEDQ45NVBmLOU78Cl68LGf8JOUY0l3cd8ehQjGyR9a12GXwRktepslp
hw9xu8uYmE93fD+MIe/fUs7W/WvIVgFSskhswlvD3kAFpEAsMczjLGVSRQlBE90L
OK7v1HKxiIUJa17g3LmiCFa59ZjrnSHGpOOv9IPAFU/LzFIU47lcFwRFjgfB8po=
=8vFi
-----END PGP SIGNATURE-----
Merge tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull more device mapper changes from Mike Snitzer:
- Significant dm-crypt CPU scalability performance improvements thanks
to changes that enable effective use of an unbound workqueue across
all available CPUs. A large battery of tests were performed to
validate these changes, summary of results is available here:
https://www.redhat.com/archives/dm-devel/2015-February/msg00106.html
- A few additional stable fixes (to DM core, dm-snapshot and dm-mirror)
and a small fix to the dm-space-map-disk.
* tag 'dm-3.20-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix a possible invalid memory access on unload
dm: fix a race condition in dm_get_md
dm crypt: sort writes
dm crypt: add 'submit_from_crypt_cpus' option
dm crypt: offload writes to thread
dm crypt: remove unused io_pool and _crypt_io_pool
dm crypt: avoid deadlock in mempools
dm crypt: don't allocate pages for a partial request
dm crypt: use unbound workqueue for request processing
dm io: reject unsupported DISCARD requests with EOPNOTSUPP
dm mirror: do not degrade the mirror on discard error
dm space map disk: fix sm_disk_count_is_more_than_one()
Pull more input updates from Dmitry Torokhov:
"The second round of updates for the input subsystem.
Updates to ALPS an bfin_roraty drivers and a couple oother fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - use IS_ENABLED instead of homegrown code
Input: bfin_rotary - introduce open and close methods
Input: bfin_rotary - convert to use managed resources
Input: bfin_rotary - use generic IO functions
Input: bfin_rotary - move pin lists into into platform data
Input: bfin_rotary - move platform header to linux/platform_data
Input: bfin_rotary - mark suspend and resume code as __maybe_unused
Input: bfin_rotary - fix potential oops in interrupt handler
Input: ALPS - move v7 packet info to Documentation and v6 packet info
Input: ALPS - fix confusing comment in protocol data
Input: ALPS - do not mix trackstick and external PS/2 mouse data
Input: ALPS - fix trackstick detection on some Dell Latitudes
Input: ALPS - consolidate setting protocol parameters
Input: ALPS - split protocol data from model info
Input: ALPS - make Rushmore a separate protocol
Input: ALPS - renumber protocol numbers
Input: adi - remove an unnecessary check
Input: pxa27x_keypad - remove an unneeded NULL check
Input: soc_button_array - use "Windows" key for "Home"
Pull i2c updates from Wolfram Sang:
"Summary:
- legacy PM code removed from the core, there were no users anymore
(thanks to Lars-Peter Clausen)
- new driver for Broadcom iProc
- bigger driver updates for designware, rk3x, cadence, ocores
- a bunch of smaller updates and bugfixes"
* 'i2c/for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (31 commits)
i2c: ocores: rework clk code to handle NULL cookie
i2c: designware-baytrail: another fixup for proper Kconfig dependencies
i2c: fix reference to functionality constants definition
i2c: iproc: Add Broadcom iProc I2C Driver
i2c: designware-pci: update Intel copyright line
i2c: ocores: add common clock support
i2c: hix5hd2: add COMPILE_TEST
i2c: clarify comments about the dev_released completion
i2c: ocores: fix clock-frequency binding usage
i2c: tegra: Maintain CPU endianness
i2c: designware-baytrail: use proper Kconfig dependencies
i2c: designware: Do not calculate SCL timing parameters needlessly
i2c: do not try to load modules for of-registered devices
i2c: designware: Add Intel Baytrail PMIC I2C bus support
i2c: designware: Add i2c bus locking support
of: i2c: Add i2c-mux-idle-disconnect DT property to PCA954x mux driver
i2c: designware: use {readl|writel}_relaxed instead of readl/writel
i2c: designware-pci: no need to provide clk_khz
i2c: designware-pci: remove Moorestown support
i2c: imx: whitespace and checkpatch cleanup
...
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Pull misc x86 fixes from Ingo Molnar:
"This contains:
- EFI fixes
- a boot printout fix
- ASLR/kASLR fixes
- intel microcode driver fixes
- other misc fixes
Most of the linecount comes from an EFI revert"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm/ASLR: Avoid PAGE_SIZE redefinition for UML subarch
x86/microcode/intel: Handle truncated microcode images more robustly
x86/microcode/intel: Guard against stack overflow in the loader
x86, mm/ASLR: Fix stack randomization on 64-bit systems
x86/mm/init: Fix incorrect page size in init_memory_mapping() printks
x86/mm/ASLR: Propagate base load address calculation
Documentation/x86: Fix path in zero-page.txt
x86/apic: Fix the devicetree build in certain configs
Revert "efi/libstub: Call get_memory_map() to obtain map and desc sizes"
x86/efi: Avoid triple faults during EFI mixed mode calls
* KDB: improved searching
* No longer enter debug core on panic if panic timeout is set
KGDB/KDB regressions / cleanups
* fix pdf doc build errors
* prevent junk characters on kdb console from printk levels
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TH0R
-----END PGP SIGNATURE-----
Merge tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb
Pull kgdb/kdb updates from Jason Wessel:
"KGDB/KDB New:
- KDB: improved searching
- No longer enter debug core on panic if panic timeout is set
KGDB/KDB regressions / cleanups
- fix pdf doc build errors
- prevent junk characters on kdb console from printk levels"
* tag 'for_linux-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/kgdb:
kgdb, docs: Fix <para> pdfdocs build errors
debug: prevent entering debug mode on panic/exception.
kdb: Const qualifier for kdb_getstr's prompt argument
kdb: Provide forward search at more prompt
kdb: Fix a prompt management bug when using | grep
kdb: Remove stack dump when entering kgdb due to NMI
kdb: Avoid printing KERN_ levels to consoles
kdb: Fix off by one error in kdb_cpu()
kdb: fix incorrect counts in KDB summary command output
- Use of_irq_init() to initialize interrupt controllers
- Get rid of some unlikely()
- Add CIB to support SATA and other interrupts
- Add support for CIU SUM2 interrupt sources
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Leonid Rosenboim <lrosenboim@caviumnetworks.com>
Signed-off-by: Aleksey Makarov <aleksey.makarov@auriga.com>
Signed-off-by: Peter Swain <peter.swain@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8947/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull more thermal managament updates from Zhang Rui:
"Specifics:
- Exynos thermal driver refactoring. Several cleanups, code
optimization, unused symbols removal, and unused feature removal in
Exynos thermal driver. Thanks Lukasz for this effort.
- Exynos thermal driver support to OF thermal. After the code
refactoring, the driver earned the support to OF thermal. Chip
thermal data were moved from driver code to DTS, reducing the code
footprint. Thanks Lukasz for this.
- After receiving the OF thermal support, the exynos thermal driver
now must allow modular build. Thanks Arnd for detecting, reporting
and fixing this.
- Exynos thermal driver support to Exynos 7 SoC. Thanks Abhilash for
this.
- Accurate temperature reporting on Rockchip thermal driver, thanks
to Caesar.
- Fix on how OF thermal enables its zones, thanks Lukasz for fixing.
- Fixes in OF thermal examples under Documentation/. Thanks Srinivas
for fixing"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: exynos: Add TMU support for Exynos7 SoC
dts: Documentation: Add documentation for Exynos7 SoC thermal bindings
cpufreq: exynos: allow modular build
thermal: Fix examples in DT documentation
thermal: exynos: Correct sanity check at exynos_report_trigger() function
thermal: Kconfig: Remove config for not used EXYNOS_THERMAL_CORE
thermal: exynos: Remove exynos_tmu_data.c file
thermal: rockchip: make temperature reporting much more accurate
thermal: exynos: Remove exynos_thermal_common.[c|h] files
thermal: samsung: core: Exynos TMU rework to use device tree for configuration
dts: Documentation: Update exynos-thermal.txt example for Exynos5440
dts: Documentation: Extending documentation entry for exynos-thermal
cpufreq: exynos: Use device tree to determine if cpufreq cooling should be registered
thermal: exynos: Modify exynos thermal code to use device tree for cpu cooling configuration
thermal: exynos: Provide thermal_exynos.h file to be included in device tree files
thermal: exynos: cosmetic: Correct comment format
thermal: of: Enable thermal_zoneX when sensor is correctly added
toshiba_acpi: Add support for missing features from the Windows driver,
bump the sysfs version, and clean up the driver.
thinkpad_acpi: BIOS string versions, unhandled hkey events.
samsung-laptop: Add native backlight quirk, enable better lid handling.
intel_scu_ipc: Read resources from PCI configuration
other: Fix sparse warnings, general cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU5Xg2AAoJEKbMaAwKp364WaUH/Akf1jrGGaC8czGVsvAz4syV
jV+4yHA1z/E1sy1LjS7gKxpaYO5j5a6Nv0488kaM/RPZoVPSXgGsrCS/HPjpRJIR
90PGQuZ3gUWpqt6ICqjs22fHVQ/k0NF7uiLgqOsACnLWAN7ts3GXNs6CLpzlwhQY
+YXzw3ac1QeB3lSKYxTmRKRZ9qCoHBmONSG/DzyHw8cmXI9LuSd7LCs8BHsg3M1v
/WYJlLTJRgS5POfPenWoW1GQ0tN9OgC19Hk4dtFMv0U1s6au7z0a8rFqHc0qR18b
tMkf9/8kaatTrKLlWhxX2/Wyenu8wpVjSYvRrRHsMCJRaWHyQQStd3Lhvw0Kzyg=
=W5L5
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull platform driver update from Darren Hart:
"This includes a significant update to the toshiba_acpi driver,
bringing it to feature parity with the Windows driver, followed by
some needed cleanups.
The other changes are mostly minor updates, quirks, sparse fixes, or
cleanups.
Details:
- toshiba_acpi:
Add support for missing features from the Windows driver, bump the
sysfs version, and clean up the driver.
- thinkpad_acpi:
BIOS string versions, unhandled hkey events.
- msamsung-laptop:
Add native backlight quirk, enable better lid handling.
- intel_scu_ipc:
Read resources from PCI configuration
- other:
Fix sparse warnings, general cleanups"
* tag 'platform-drivers-x86-v3.20-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (34 commits)
toshiba_acpi: Cleanup GPL header
toshiba_acpi: Cleanup comment blocks and capitalization
toshiba_acpi: Make use of DEVICE_ATTR_{RO, RW} macros
toshiba_acpi: Drop the toshiba_ prefix from sysfs function names
toshiba_acpi: Move sysfs function and struct declarations further down
Documentation/ABI: Add file describing the sysfs entries for toshiba_acpi
toshiba_acpi: Clean file according to coding style
toshiba_acpi: Bump version number to 0.21
toshiba_acpi: Add support to enable/disable USB 3
toshiba_acpi: Add support for Panel Power ON
toshiba_acpi: Add support for Keyboard functions mode
toshiba_acpi: Add fan entry to sysfs
toshiba_acpi: Add version entry to sysfs
thinkpad_acpi: support new BIOS version string pattern
thinkpad_acpi: unhandled hkey event
toshiba_acpi: Make toshiba_eco_mode_available more robust
classmate-laptop: Fix sparse warning (0 as NULL)
Sony-laptop: Fix sparse warning (make undeclared var static)
thinkpad_acpi.c: Fix sparse warning (make undeclared var static)
samsung-laptop.c: Prefer kstrtoint over single variable sscanf
...
kgdb.pdf failed to build from 'make pdfdocs' giving errors such as:
jade:... Documentation/DocBook/kgdb.xml:200:8:E:
document type does not allow element "para" here; missing one of
"footnote", "caution", "important", "note", "tip", "warning",
"blockquote", "informalexample" start-tag
Fixing minor <para> and <sect> issues allows kgdb.pdf to be generated
under Fedora20.
Originally submitted by rajaneesh.acharya@yahoo.com in 2011, discussed here:
http://permalink.gmane.org/gmane.linux.documentation/3954
as patch:
The following are the enhancements that removed the errors
while issuing "make pdfdocs"
[graham.whaley@intel.com: Improved commit message and ported to 3.18.1]
Signed-off-by: Graham Whaley <graham.whaley@intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Pull misc kbuild changes from Michal Marek:
"Just a few non-critical kbuild changes:
- builddeb adds the actual distribution name in the changelog
- documentation fixes"
* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: trivial - fix the help doc of CONFIG_CC_OPTIMIZE_FOR_SIZE
kbuild: Update documentation of clean-files and clean-dirs
builddeb: Try to determine distribution
builddeb: Update year and git repository URL in debian/copyright
Pull kbuild updates from Michal Marek:
- several cleanups in kbuild
- serialize multiple *config targets so that 'make defconfig kvmconfig'
works
- The cc-ifversion macro got support for an else-branch
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild,gcov: simplify kernel/gcov/Makefile more
kbuild: allow cc-ifversion to have the argument for false condition
kbuild,gcov: simplify kernel/gcov/Makefile
kbuild,gcov: remove unnecessary workaround
kbuild: do not add $(call ...) to invoke cc-version or cc-fullversion
kbuild: fix cc-ifversion macro
kbuild: drop $(version_h) from MRPROPER_FILES
kbuild: use mixed-targets when two or more config targets are given
kbuild: remove redundant line from bounds.h/asm-offsets.h
kbuild: merge bounds.h and asm-offsets.h rules
kbuild: Drop support for clean-rule
Since commit 607ca46e97 ('UAPI: (Scripted) Disintegrate include/linux') the
list of functionality constants moved to include/uapi/linux/i2c.h. Update the
reference accordingly.
Fixes: 607ca46e97 ('UAPI: (Scripted) Disintegrate include/linux')
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
