2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2024-12-22 20:23:57 +08:00
Commit Graph

137 Commits

Author SHA1 Message Date
Oliver Hartkopp
a2ec19f888 can: remove obsolete assignment for CAN protocol error type
The assignment 'cf->data[2] |= CAN_ERR_PROT_UNSPEC' used at CAN error message
creation time is obsolete as CAN_ERR_PROT_UNSPEC is zero and cf->data[2] is
initialized with zero in alloc_can_err_skb() anyway.

So we could either assign 'cf->data[2] = CAN_ERR_PROT_UNSPEC' correctly or we
can remove the obsolete OR operation entirely.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2015-11-23 09:37:38 +01:00
Mirza Krak
7cecd9ab80 can: sja1000: clear interrupts on start
According to SJA1000 data sheet error-warning (EI) interrupt is not
cleared by setting the controller in to reset-mode.

Then if we have the following case:
- system is suspended (echo mem > /sys/power/state) and SJA1000 is left
  in operating state
- A bus error condition occurs which activates EI interrupt, system is
  still suspended which means EI interrupt will be not be handled nor
  cleared.

If the above two events occur, on resume there is no way to return the
SJA1000 to operating state, except to cycle power to it.

By simply reading the IR register on start we will clear any previous
conditions that could be present.

Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Reported-by: Christian Magnusson <Christian.Magnusson@semcon.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2015-11-23 09:35:21 +01:00
Stephane Grosjean
7253054e5d can: peak_pci: add unused device id. in devices table
While new PEAK_PCIE_OEM_ID has been defined since 3.17, no corresponding
entry has been added in the peak_pci_tbl[] of the peak_pci CAN driver.

This patch enables now users of the PCAN-PCI Express OEM card to run the
peak_pci driver too.

Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2015-09-30 12:57:58 +02:00
Marc Kleine-Budde
889dd06e10 can: sja1000: don't touch skb after netif_rx()
There is no guarantee that the skb is in the same state after calling
net_receive_skb() or netif_rx(). It might be freed or reused. Not really
harmful as its a read access, except you turn on the proper debugging options
which catch a use after free.

Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2015-07-15 09:04:28 +02:00
Fabian Frederick
486e957033 can: constify of_device_id array
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)

Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-03-17 15:00:23 -04:00
Linus Torvalds
e6b5be2be4 Driver core patches for 3.19-rc1
Here's the set of driver core patches for 3.19-rc1.
 
 They are dominated by the removal of the .owner field in platform
 drivers.  They touch a lot of files, but they are "simple" changes, just
 removing a line in a structure.
 
 Other than that, a few minor driver core and debugfs changes.  There are
 some ath9k patches coming in through this tree that have been acked by
 the wireless maintainers as they relied on the debugfs changes.
 
 Everything has been in linux-next for a while.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
 53kAoLeteByQ3iVwWurwwseRPiWa8+MI
 =OVRS
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core update from Greg KH:
 "Here's the set of driver core patches for 3.19-rc1.

  They are dominated by the removal of the .owner field in platform
  drivers.  They touch a lot of files, but they are "simple" changes,
  just removing a line in a structure.

  Other than that, a few minor driver core and debugfs changes.  There
  are some ath9k patches coming in through this tree that have been
  acked by the wireless maintainers as they relied on the debugfs
  changes.

  Everything has been in linux-next for a while"

* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
  Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
  fs: debugfs: add forward declaration for struct device type
  firmware class: Deletion of an unnecessary check before the function call "vunmap"
  firmware loader: fix hung task warning dump
  devcoredump: provide a one-way disable function
  device: Add dev_<level>_once variants
  ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
  ath: use seq_file api for ath9k debugfs files
  debugfs: add helper function to create device related seq_file
  drivers/base: cacheinfo: remove noisy error boot message
  Revert "core: platform: add warning if driver has no owner"
  drivers: base: support cpu cache information interface to userspace via sysfs
  drivers: base: add cpu_device_create to support per-cpu devices
  topology: replace custom attribute macros with standard DEVICE_ATTR*
  cpumask: factor out show_cpumap into separate helper function
  driver core: Fix unbalanced device reference in drivers_probe
  driver core: fix race with userland in device_add()
  sysfs/kernfs: make read requests on pre-alloc files use the buffer.
  sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
  fs: sysfs: return EGBIG on write if offset is larger than file size
  ...
2014-12-14 16:10:09 -08:00
Andri Yngvason
215db1856e can: sja1000: Consolidate and unify state change handling
Replacing error state change handling with the new mechanism.

Signed-off-by: Andri Yngvason <andri.yngvason@marel.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-12-07 21:22:09 +01:00
Sudip Mukherjee
4e2061b1e1 can: remove unused variable
these variable were only assigned some values, but then never
reused again.
so they are safe to be removed.

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-11-18 16:52:18 +01:00
Wolfram Sang
ac52841ce7 net: can: sja1000: drop owner assignment from platform_drivers
A platform_driver does not need to set an owner, it will be populated by the
driver core.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2014-10-20 16:21:01 +02:00
David S. Miller
1f6d80358d Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	arch/mips/net/bpf_jit.c
	drivers/net/can/flexcan.c

Both the flexcan and MIPS bpf_jit conflicts were cases of simple
overlapping changes.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-09-23 12:09:27 -04:00
Oliver Hartkopp
4be0015c95 can: peak_pci: add PCI ID definition pcie card variant
Add PCI ID definition for the single channel PCAN ExpressCard 34 adapter. Due
to the subsystem id evaluation the correct number of channels (here 1) is
created at initialization time. Tested including the LED functionality.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-09-18 11:15:09 +02:00
David S. Miller
f9474ddfaa Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pulling to get some TIPC fixes that a net-next series depends
upon.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-08-23 11:12:08 -07:00
Mirza Krak
9e37bc6c63 can: sja1000: Validate initialization state in start method
When sja1000 is not compiled as module the SJA1000 chip is only
initialized during device registration on kernel boot. Should the chip
get a hardware reset there is no way to reinitialize it without re-
booting the Linux kernel.

This patch adds a check in sja1000_start if the chip is initialized, if
not we initialize it.

Signed-off-by: Mirza Krak <mirza.krak@hostmobility.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-08-21 10:49:34 +02:00
Wolfram Sang
4ade6feb52 net: can: use kbuild magic to inherit debug settings
No need to manually copy debug settings into subdir Makefiles. kbuild
has a mechanism for inheriting, so let's use it.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-08-18 01:03:38 +02:00
Benoit Taine
9baa3c34ac PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-08-12 12:15:14 -06:00
Nikita Edward Baruzdin
5b853ec349 can: sja1000: Add support for CAN_CTRLMODE_PRESUME_ACK
SJA1000 has a self test mode (STM) which does not require
acknowledgement for the successful message transmission. In this mode a
node test is possible without any other active node on the bus.

This patch adds a possibility to set STM for SJA1000 controller through
specifying the corresponding CAN_CTRLMODE_PRESUME_ACK netlink flag.

Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:34:27 +02:00
Nikita Edward Baruzdin
dcf9e15267 can: sja1000: Add support for CAN_CTRLMODE_LOOPBACK
This adds support for hardware loopback in SJA1000 by utilising its self
reception request (SRR) feature. Upon SRR the message is transmitted and
received simultaneously, meaning you can't have hardware loopback
without actually sending a message to the CAN bus in case of SJA1000.

Signed-off-by: Nikita Edward Baruzdin <nebaruzdin@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-07-15 09:34:23 +02:00
Stephane Grosjean
0b5a958cf4 can: peak_pci: prevent use after free at netdev removal
As remarked by Christopher R. Baker in his post at

http://marc.info/?l=linux-can&m=139707295706465&w=2

there's a possibility for an use after free condition at device removal.

This simplified patch introduces an additional variable to prevent the issue.
Thanks for catching this.

Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Christopher R. Baker <cbaker@rec.ri.cmu.edu>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-05-21 08:17:03 +02:00
Oliver Hartkopp
a9edcdedbd can: sja1000_isa: add locking for indirect register access mode
When accessing the SJA1000 controller registers in the indirect access mode,
writing the register number and reading/writing the data has to be an atomic
attempt.

As the sja1000_isa driver is an old style driver with a fixed number of
instances the locking variable depends on the same index like all the other
configuration elements given on the module command line.

As a positive side effect dev->dev_id is populated by the instance index,
which was missing in 3e66d0138c ("can: populate netdev::dev_id for udev
discrimination").

Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-04-24 22:22:53 +02:00
Uwe Kleine-König
ce816fa88c Kconfig: rename HAS_IOPORT to HAS_IOPORT_MAP
If the renamed symbol is defined lib/iomap.c implements ioport_map and
ioport_unmap and currently (nearly) all platforms define the port
accessor functions outb/inb and friend unconditionally.  So
HAS_IOPORT_MAP is the better name for this.

Consequently NO_IOPORT is renamed to NO_IOPORT_MAP.

The motivation for this change is to reintroduce a symbol HAS_IOPORT
that signals if outb/int et al are available.  I will address that at
least one merge window later though to keep surprises to a minimum and
catch new introductions of (HAS|NO)_IOPORT.

The changes in this commit were done using:

	$ git grep -l -E '(NO|HAS)_IOPORT' | xargs perl -p -i -e 's/\b((?:CONFIG_)?(?:NO|HAS)_IOPORT)\b/$1_MAP/'

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2014-04-07 16:36:11 -07:00
Christopher R. Baker
3e66d0138c can: populate netdev::dev_id for udev discrimination
My objective is to be able to totally discriminate CAN ports on multi-port
cards via udev so as to rename them to semantically interesting/unique names
for my system (e.g., "ecuCAN" and "auxCAN" instead of "can0" and "can1").

The following patch assigns the dev_id field to match the channel number on all
multi-channel devices. I can only test my two-port Peak PCI card, but it works
as expected: ATTRS{dev_id} now expresses the port number and my udev rules now
unambiguously pick out and rename my individual CAN ports.

Signed-off-by: Christopher R. Baker <cbaker@rec.ri.cmu.edu>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net> [PEAK PCAN-USB pro and EMS PCMCIA]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-03-17 09:20:16 +01:00
Oliver Hartkopp
c971fa2ae4 can: Unify MTU settings for CAN interfaces
CAN interfaces only support MTU values of 16 (CAN 2.0) and 72 (CAN FD).
Setting the MTU to other values is pointless but it does not really hurt.
With the introduction of the CAN FD support in drivers/net/can a new
function to switch the MTU for CAN FD has been introduced.

This patch makes use of this can_change_mtu() function to check for correct
MTU settings also in legacy CAN (2.0) devices.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-03-17 09:20:16 +01:00
Florian Vaussard
b18ec27c65 can: sja1000: of: add reg-io-width property for 8, 16 and 32-bit register access
Add the 'reg-io-width' property for 8, 16 and 32-bit access, like
what is currently done with IORESOURCE_MEM_{8,16,32}BIT for non-OF
boot.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-02-06 11:50:57 +01:00
Florian Vaussard
02729c3d08 can: sja1000: fuse of_platform into platform
The OpenFirmware probe can be merged into the standard platform
probe to leverage common code.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-02-04 10:10:51 +01:00
Florian Vaussard
342180f7dc can: sja1000: platform: use devm_* APIs
Simplify probe and remove functions by converting most of the resources
to use devm_* APIs.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-02-04 10:10:47 +01:00
Florian Vaussard
909285c437 can: sja1000: convert printk to use netdev API
Use netdev_* where applicable.

Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-02-04 10:04:21 +01:00
Oleg Moroz
2dcb90ef4f can: sja1000: add support for Elcus CAN200PCI
This patch adds support for Elcus CAN200PCI card.

Signed-off-by: Oleg Moroz <oleg.moroz@mcc.vniiem.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2014-01-11 19:43:16 +01:00
Jeff Kirsher
05780d9808 can: Fix FSF address in file headers
Several files refer to an old address for the Free Software Foundation
in the file header comment.  Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.

CC: Wolfgang Grandegger <wg@grandegger.com>
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-12-17 11:47:21 +01:00
Oliver Hartkopp
2fea6cd303 can: sja1000: fix {pre,post}_irq() handling and IRQ handler return value
This patch fixes the issue that the sja1000_interrupt() function may have
returned IRQ_NONE without processing the optional pre_irq() and post_irq()
function before. Further the irq processing counter 'n' is moved to the end of
the while statement to return correct IRQ_[NONE|HANDLED] values at error
conditions.

Reported-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-11-25 21:16:53 +01:00
Linus Torvalds
42a2d923cc Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) The addition of nftables.  No longer will we need protocol aware
    firewall filtering modules, it can all live in userspace.

    At the core of nftables is a, for lack of a better term, virtual
    machine that executes byte codes to inspect packet or metadata
    (arriving interface index, etc.) and make verdict decisions.

    Besides support for loading packet contents and comparing them, the
    interpreter supports lookups in various datastructures as
    fundamental operations.  For example sets are supports, and
    therefore one could create a set of whitelist IP address entries
    which have ACCEPT verdicts attached to them, and use the appropriate
    byte codes to do such lookups.

    Since the interpreted code is composed in userspace, userspace can
    do things like optimize things before giving it to the kernel.

    Another major improvement is the capability of atomically updating
    portions of the ruleset.  In the existing netfilter implementation,
    one has to update the entire rule set in order to make a change and
    this is very expensive.

    Userspace tools exist to create nftables rules using existing
    netfilter rule sets, but both kernel implementations will need to
    co-exist for quite some time as we transition from the old to the
    new stuff.

    Kudos to Patrick McHardy, Pablo Neira Ayuso, and others who have
    worked so hard on this.

 2) Daniel Borkmann and Hannes Frederic Sowa made several improvements
    to our pseudo-random number generator, mostly used for things like
    UDP port randomization and netfitler, amongst other things.

    In particular the taus88 generater is updated to taus113, and test
    cases are added.

 3) Support 64-bit rates in HTB and TBF schedulers, from Eric Dumazet
    and Yang Yingliang.

 4) Add support for new 577xx tigon3 chips to tg3 driver, from Nithin
    Sujir.

 5) Fix two fatal flaws in TCP dynamic right sizing, from Eric Dumazet,
    Neal Cardwell, and Yuchung Cheng.

 6) Allow IP_TOS and IP_TTL to be specified in sendmsg() ancillary
    control message data, much like other socket option attributes.
    From Francesco Fusco.

 7) Allow applications to specify a cap on the rate computed
    automatically by the kernel for pacing flows, via a new
    SO_MAX_PACING_RATE socket option.  From Eric Dumazet.

 8) Make the initial autotuned send buffer sizing in TCP more closely
    reflect actual needs, from Eric Dumazet.

 9) Currently early socket demux only happens for TCP sockets, but we
    can do it for connected UDP sockets too.  Implementation from Shawn
    Bohrer.

10) Refactor inet socket demux with the goal of improving hash demux
    performance for listening sockets.  With the main goals being able
    to use RCU lookups on even request sockets, and eliminating the
    listening lock contention.  From Eric Dumazet.

11) The bonding layer has many demuxes in it's fast path, and an RCU
    conversion was started back in 3.11, several changes here extend the
    RCU usage to even more locations.  From Ding Tianhong and Wang
    Yufen, based upon suggestions by Nikolay Aleksandrov and Veaceslav
    Falico.

12) Allow stackability of segmentation offloads to, in particular, allow
    segmentation offloading over tunnels.  From Eric Dumazet.

13) Significantly improve the handling of secret keys we input into the
    various hash functions in the inet hashtables, TCP fast open, as
    well as syncookies.  From Hannes Frederic Sowa.  The key fundamental
    operation is "net_get_random_once()" which uses static keys.

    Hannes even extended this to ipv4/ipv6 fragmentation handling and
    our generic flow dissector.

14) The generic driver layer takes care now to set the driver data to
    NULL on device removal, so it's no longer necessary for drivers to
    explicitly set it to NULL any more.  Many drivers have been cleaned
    up in this way, from Jingoo Han.

15) Add a BPF based packet scheduler classifier, from Daniel Borkmann.

16) Improve CRC32 interfaces and generic SKB checksum iterators so that
    SCTP's checksumming can more cleanly be handled.  Also from Daniel
    Borkmann.

17) Add a new PMTU discovery mode, IP_PMTUDISC_INTERFACE, which forces
    using the interface MTU value.  This helps avoid PMTU attacks,
    particularly on DNS servers.  From Hannes Frederic Sowa.

18) Use generic XPS for transmit queue steering rather than internal
    (re-)implementation in virtio-net.  From Jason Wang.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
  random32: add test cases for taus113 implementation
  random32: upgrade taus88 generator to taus113 from errata paper
  random32: move rnd_state to linux/random.h
  random32: add prandom_reseed_late() and call when nonblocking pool becomes initialized
  random32: add periodic reseeding
  random32: fix off-by-one in seeding requirement
  PHY: Add RTL8201CP phy_driver to realtek
  xtsonic: add missing platform_set_drvdata() in xtsonic_probe()
  macmace: add missing platform_set_drvdata() in mace_probe()
  ethernet/arc/arc_emac: add missing platform_set_drvdata() in arc_emac_probe()
  ipv6: protect for_each_sk_fl_rcu in mem_check with rcu_read_lock_bh
  vlan: Implement vlan_dev_get_egress_qos_mask as an inline.
  ixgbe: add warning when max_vfs is out of range.
  igb: Update link modes display in ethtool
  netfilter: push reasm skb through instead of original frag skbs
  ip6_output: fragment outgoing reassembled skb properly
  MAINTAINERS: mv643xx_eth: take over maintainership from Lennart
  net_sched: tbf: support of 64bit rates
  ixgbe: deleting dfwd stations out of order can cause null ptr deref
  ixgbe: fix build err, num_rx_queues is only available with CONFIG_RPS
  ...
2013-11-13 17:40:34 +09:00
Rob Herring
fc84b0c3dc drivers: remove unnecessary prom.h includes
Remove unnecessary prom.h includes in preparation to remove implicit
includes of prom.h.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-can@vger.kernel.org
Cc: netdev@vger.kernel.org
2013-10-09 20:03:58 -05:00
Jingoo Han
a0c7d83322 can: sja1000: remove unnecessary pci_set_drvdata()
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-09-21 15:43:16 +02:00
Jingoo Han
ecd78d9753 can: sja1000: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-09-21 15:43:14 +02:00
Jingoo Han
00e4bbc8cd net: can: use platform_{get,set}_drvdata()
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.

Also, unnecessary dev_set_drvdata() is removed, because the driver core
clears the driver data to NULL after device_release or on probe failure.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-06-03 13:13:49 +02:00
Linus Torvalds
73287a43cc Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:
 "Highlights (1721 non-merge commits, this has to be a record of some
  sort):

   1) Add 'random' mode to team driver, from Jiri Pirko and Eric
      Dumazet.

   2) Make it so that any driver that supports configuration of multiple
      MAC addresses can provide the forwarding database add and del
      calls by providing a default implementation and hooking that up if
      the driver doesn't have an explicit set of handlers.  From Vlad
      Yasevich.

   3) Support GSO segmentation over tunnels and other encapsulating
      devices such as VXLAN, from Pravin B Shelar.

   4) Support L2 GRE tunnels in the flow dissector, from Michael Dalton.

   5) Implement Tail Loss Probe (TLP) detection in TCP, from Nandita
      Dukkipati.

   6) In the PHY layer, allow supporting wake-on-lan in situations where
      the PHY registers have to be written for it to be configured.

      Use it to support wake-on-lan in mv643xx_eth.

      From Michael Stapelberg.

   7) Significantly improve firewire IPV6 support, from YOSHIFUJI
      Hideaki.

   8) Allow multiple packets to be sent in a single transmission using
      network coding in batman-adv, from Martin Hundebøll.

   9) Add support for T5 cxgb4 chips, from Santosh Rastapur.

  10) Generalize the VXLAN forwarding tables so that there is more
      flexibility in configurating various aspects of the endpoints.
      From David Stevens.

  11) Support RSS and TSO in hardware over GRE tunnels in bxn2x driver,
      from Dmitry Kravkov.

  12) Zero copy support in nfnelink_queue, from Eric Dumazet and Pablo
      Neira Ayuso.

  13) Start adding networking selftests.

  14) In situations of overload on the same AF_PACKET fanout socket, or
      per-cpu packet receive queue, minimize drop by distributing the
      load to other cpus/fanouts.  From Willem de Bruijn and Eric
      Dumazet.

  15) Add support for new payload offset BPF instruction, from Daniel
      Borkmann.

  16) Convert several drivers over to mdoule_platform_driver(), from
      Sachin Kamat.

  17) Provide a minimal BPF JIT image disassembler userspace tool, from
      Daniel Borkmann.

  18) Rewrite F-RTO implementation in TCP to match the final
      specification of it in RFC4138 and RFC5682.  From Yuchung Cheng.

  19) Provide netlink socket diag of netlink sockets ("Yo dawg, I hear
      you like netlink, so I implemented netlink dumping of netlink
      sockets.") From Andrey Vagin.

  20) Remove ugly passing of rtnetlink attributes into rtnl_doit
      functions, from Thomas Graf.

  21) Allow userspace to be able to see if a configuration change occurs
      in the middle of an address or device list dump, from Nicolas
      Dichtel.

  22) Support RFC3168 ECN protection for ipv6 fragments, from Hannes
      Frederic Sowa.

  23) Increase accuracy of packet length used by packet scheduler, from
      Jason Wang.

  24) Beginning set of changes to make ipv4/ipv6 fragment handling more
      scalable and less susceptible to overload and locking contention,
      from Jesper Dangaard Brouer.

  25) Get rid of using non-type-safe NLMSG_* macros and use nlmsg_*()
      instead.  From Hong Zhiguo.

  26) Optimize route usage in IPVS by avoiding reference counting where
      possible, from Julian Anastasov.

  27) Convert IPVS schedulers to RCU, also from Julian Anastasov.

  28) Support cpu fanouts in xt_NFQUEUE netfilter target, from Holger
      Eitzenberger.

  29) Network namespace support for nf_log, ebt_log, xt_LOG, ipt_ULOG,
      nfnetlink_log, and nfnetlink_queue.  From Gao feng.

  30) Implement RFC3168 ECN protection, from Hannes Frederic Sowa.

  31) Support several new r8169 chips, from Hayes Wang.

  32) Support tokenized interface identifiers in ipv6, from Daniel
      Borkmann.

  33) Use usbnet_link_change() helper in USB net driver, from Ming Lei.

  34) Add 802.1ad vlan offload support, from Patrick McHardy.

  35) Support mmap() based netlink communication, also from Patrick
      McHardy.

  36) Support HW timestamping in mlx4 driver, from Amir Vadai.

  37) Rationalize AF_PACKET packet timestamping when transmitting, from
      Willem de Bruijn and Daniel Borkmann.

  38) Bring parity to what's provided by /proc/net/packet socket dumping
      and the info provided by netlink socket dumping of AF_PACKET
      sockets.  From Nicolas Dichtel.

  39) Fix peeking beyond zero sized SKBs in AF_UNIX, from Benjamin
      Poirier"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1722 commits)
  filter: fix va_list build error
  af_unix: fix a fatal race with bit fields
  bnx2x: Prevent memory leak when cnic is absent
  bnx2x: correct reading of speed capabilities
  net: sctp: attribute printl with __printf for gcc fmt checks
  netlink: kconfig: move mmap i/o into netlink kconfig
  netpoll: convert mutex into a semaphore
  netlink: Fix skb ref counting.
  net_sched: act_ipt forward compat with xtables
  mlx4_en: fix a build error on 32bit arches
  Revert "bnx2x: allow nvram test to run when device is down"
  bridge: avoid OOPS if root port not found
  drivers: net: cpsw: fix kernel warn on cpsw irq enable
  sh_eth: use random MAC address if no valid one supplied
  3c509.c: call SET_NETDEV_DEV for all device types (ISA/ISAPnP/EISA)
  tg3: fix to append hardware time stamping flags
  unix/stream: fix peeking with an offset larger than data in queue
  unix/dgram: fix peeking with an offset larger than data in queue
  unix/dgram: peek beyond 0-sized skbs
  openvswitch: Remove unneeded ovs_netdev_get_ifindex()
  ...
2013-05-01 14:08:52 -07:00
Linus Torvalds
4f567cbc95 Char / Misc driver update for 3.10-rc1
Here's the big char / misc driver update for 3.10-rc1
 
 A number of various driver updates, the majority being new functionality
 in the MEI driver subsystem (it's now a subsystem, it started out just a
 single driver), extcon updates, memory updates, hyper-v updates, and a
 bunch of other small stuff that doesn't fit in any other tree.
 
 All of these have been in linux-next for a while
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2.0.19 (GNU/Linux)
 
 iEYEABECAAYFAlF+mtYACgkQMUfUDdst+ymFXQCfdLsD4Cxz+jkgW+tljh9i70XD
 OFkAnRPMMhLS8/kddf02lLMYzYUFdy1U
 =zaFJ
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver update from Greg Kroah-Hartman:
 "Here's the big char / misc driver update for 3.10-rc1

  A number of various driver updates, the majority being new
  functionality in the MEI driver subsystem (it's now a subsystem, it
  started out just a single driver), extcon updates, memory updates,
  hyper-v updates, and a bunch of other small stuff that doesn't fit in
  any other tree.

  All of these have been in linux-next for a while"

* tag 'char-misc-3.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (148 commits)
  Tools: hv: Fix a checkpatch warning
  tools: hv: skip iso9660 mounts in hv_vss_daemon
  tools: hv: use FIFREEZE/FITHAW in hv_vss_daemon
  tools: hv: use getmntent in hv_vss_daemon
  Tools: hv: Fix a checkpatch warning
  tools: hv: fix checks for origin of netlink message in hv_vss_daemon
  Tools: hv: fix warnings in hv_vss_daemon
  misc: mark spear13xx-pcie-gadget as broken
  mei: fix krealloc() misuse in in mei_cl_irq_read_msg()
  mei: reduce flow control only for completed messages
  mei: reseting -> resetting
  mei: fix reading large reposnes
  mei: revamp mei_irq_read_client_message function
  mei: revamp mei_amthif_irq_read_message
  mei: revamp hbm state machine
  Revert "drivers/scsi: use module_pcmcia_driver() in pcmcia drivers"
  Revert "scsi: pcmcia: nsp_cs: remove module init/exit function prototypes"
  scsi: pcmcia: nsp_cs: remove module init/exit function prototypes
  mei: wd: fix line over 80 characters
  misc: tsl2550: Use dev_pm_ops
  ...
2013-04-29 11:18:34 -07:00
David S. Miller
6e0895c2ea Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/emulex/benet/be_main.c
	drivers/net/ethernet/intel/igb/igb_main.c
	drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
	include/net/scm.h
	net/batman-adv/routing.c
	net/ipv4/tcp_input.c

The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.

The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.

An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.

Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.

Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.

Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-22 20:32:51 -04:00
Oliver Hartkopp
06e1d1d718 can: sja1000: use common prefix for all sja1000 defines
This is a follow up patch to:

    f901b6b can: sja1000: fix define conflict on SH

That patch fixed a define conflict between the SH architecture and the sja1000
driver, by addind a prefix to one macro only. This patch consistently renames
the prefix of the SJA1000 controller registers from "REG_" to "SJA1000_".

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-04-16 12:39:14 +02:00
Greg Kroah-Hartman
2f093e2aa4 Merge 3.9-rc7 into char-misc-next
We want the fixes in there.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-04-14 18:21:35 -07:00
Christoph Fritz
0443de5fbf can: sja1000: fix handling on dt properties on little endian systems
To get correct endianes on little endian cpus (like arm) while reading device
tree properties, this patch replaces of_get_property() with
of_property_read_u32(). While there use of_property_read_bool() for the
handling of the boolean "nxp,no-comparator-bypass" property.

Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-04-12 13:03:01 +02:00
Marc Kleine-Budde
3fd33497f8 can: sja1000: limit PEAK PCAN-PC Card to HAS_IOPORT
This patch limits the PEAK PCAN-PC Card driver to systems with ioports. Fixes a
compile time breakage on SH:

    drivers/net/can/sja1000/peak_pcmcia.c:626:2: error:
        implicit declaration of function 'ioport_unmap'

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-03-27 14:51:49 +01:00
Marc Kleine-Budde
f901b6bc40 can: sja1000: fix define conflict on SH
Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:

    drivers/net/can/sja1000/sja1000.h:59:0: warning:
        "REG_SR" redefined [enabled by default]
    arch/sh/include/asm/ptrace_32.h:25:0: note:
         this is the location of the previous definition

A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.

Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-03-27 13:39:42 +01:00
H Hartley Sweeten
fdd3f29edd drivers/net: use module_pcmcia_driver() in pcmcia drivers
Use the new module_pcmcia_driver() macro to remove the boilerplate
module init/exit code in the pcmcia drivers.

Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-03-15 12:27:33 -07:00
Linus Torvalds
a0b1c42951 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking update from David Miller:

 1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
    timestamp offset.  From Andrey Vagin.

 2) VMWARE VM VSOCK layer, from Andy King.

 3) Much improved support for virtual functions and SR-IOV in bnx2x,
    from Ariel ELior.

 4) All protocols on ipv4 and ipv6 are now network namespace aware, and
    all the compatability checks for initial-namespace-only protocols is
    removed.  Thanks to Tom Parkin for helping deal with the last major
    holdout, L2TP.

 5) IPV6 support in netpoll and network namespace support in pktgen,
    from Cong Wang.

 6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
    Protocol (MVRP) support, from David Ward.

 7) Compute packet lengths more accurately in the packet scheduler, from
    Eric Dumazet.

 8) Use per-task page fragment allocator in skb_append_datato_frags(),
    also from Eric Dumazet.

 9) Add support for connection tracking labels in netfilter, from
    Florian Westphal.

10) Fix default multicast group joining on ipv6, and add anti-spoofing
    checks to 6to4 and 6rd.  From Hannes Frederic Sowa.

11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
    times, rearrange inet frag datastructures for better cacheline
    locality, and move more operations outside of locking.  From Jesper
    Dangaard Brouer.

12) Instead of strict master <--> slave relationships, allow arbitrary
    scenerios with "upper device lists".  From Jiri Pirko.

13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
    Pirko.

14) Add a BPF filter netfilter match target, from Willem de Bruijn.

15) Orphan and delete a bunch of pre-historic networking drivers from
    Paul Gortmaker.

16) Add TSO support for GRE tunnels, from Pravin B SHelar.  Although
    this still needs some minor bug fixing before it's %100 correct in
    all cases.

17) Handle unresolved IPSEC states like ARP, with a resolution packet
    queue.  From Steffen Klassert.

18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
    Hemminger.  This was long overdue.

19) Support SO_REUSEPORT, from Tom Herbert.

20) Allow locking a socket BPF filter, so that it cannot change after a
    process drops capabilities.

21) Add VLAN filtering to bridge, from Vlad Yasevich.

22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
    the ipv6 routes, from YOSHIFUJI Hideaki.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
  ipv6: fix race condition regarding dst->expires and dst->from.
  net: fix a wrong assignment in skb_split()
  ip_gre: remove an extra dst_release()
  ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
  atl1c: restore buffer state
  net: fix a build failure when !CONFIG_PROC_FS
  net: ipv4: fix waring -Wunused-variable
  net: proc: fix build failed when procfs is not configured
  Revert "xen: netback: remove redundant xenvif_put"
  net: move procfs code to net/core/net-procfs.c
  qmi_wwan, cdc-ether: add ADU960S
  bonding: set sysfs device_type to 'bond'
  bonding: fix bond_release_all inconsistencies
  b44: use netdev_alloc_skb_ip_align()
  xen: netback: remove redundant xenvif_put
  net: fec: Do a sanity check on the gpio number
  ip_gre: propogate target device GSO capability to the tunnel device
  ip_gre: allow CSUM capable devices to handle packets
  bonding: Fix initialize after use for 3ad machine state spinlock
  bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
  ...
2013-02-20 18:58:50 -08:00
Joe Perches
09da6c5f60 can: Remove unnecessary alloc/OOM messages
alloc failures already get standardized OOM
messages and a dump_stack.

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-02-04 13:22:33 -05:00
Fabio Baltieri
a04282f54b can: sja1000: add LED trigger support
Add support for canbus activity led indicators on sja1000 devices by
calling appropriate can_led functions.

These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.

Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-01-26 16:59:00 +01:00
Marc Kleine-Budde
af5fd6da40 can: sja1000: correct indention of Kconfig help text
This patch changes the indention of the Kconfig help text to the default
<tab> + 2 <space>.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-01-26 16:58:58 +01:00
Marc Kleine-Budde
6586c5d74e can: Kconfig: convert 'depends on CAN_DEV' into 'if CAN_DEV...endif' block
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2013-01-26 16:58:58 +01:00
Tejun Heo
1cab3f9fcc sja1000: don't use [delayed_]work_pending()
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it.  Most uses are unnecessary
and quite a few of them are buggy.

Remove unnecessary pending tests from sja1000.  Only compile tested.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: netdev@vger.kernel.org
2012-12-28 13:40:15 -08:00
Marc Kleine-Budde
50077cd2dd can: sja1000: fix compilation on x86
Since commit:
04df251 can: sja1000: Make sja1000_of_platform selectable and compilable on SPARC
the driver can be activated on non powerpc platform like x86 or sparc. Without
this patch the driver fails to compile on platform that don't define NO_IRQ,
like x86.

Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-12-15 17:14:38 -08:00