Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver did not work anymore since I2C has gone broken due
to recent commit:
commit 37ebaf6891
[media] dvb-frontends: Don't use dynamic static allocation
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable@vger.kernel.org
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv090x.c:750:1: warning: 'stv090x_write_regs.constprop.6' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stv0367.c:791:1: warning: 'stv0367_writeregs.constprop.4' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/stb0899_drv.c:540:1: warning: 'stb0899_write_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/af9013.c:77:1: warning: 'af9013_wr_regs_i2c' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:188:1: warning: 'af9033_wr_reg_val_tab' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/af9033.c:68:1: warning: 'af9033_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/cxd2820r_core.c:84:1: warning: 'cxd2820r_rd_regs_i2c.isra.1' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2830.c:56:1: warning: 'rtl2830_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/rtl2832.c:187:1: warning: 'rtl2832_wr' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:52:1: warning: 'tda10071_wr_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda10071.c:84:1: warning: 'tda10071_rd_regs' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/bcm3510.c:230:1: warning: 'bcm3510_do_hab_cmd' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/itd1000.c:69:1: warning: 'itd1000_write_regs.constprop.0' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/mt312.c:126:1: warning: 'mt312_write' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/nxt200x.c:111:1: warning: 'nxt200x_writebytes' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stb6100.c:216:1: warning: 'stb6100_write_reg_range.constprop.3' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110.c:98:1: warning: 'stv6110_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/stv6110x.c:85:1: warning: 'stv6110x_write_regs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/tda18271c2dd.c:147:1: warning: 'WriteRegs' uses dynamic stack allocation [enabled by default]
drivers/media/dvb-frontends/zl10039.c:119:1: warning: 'zl10039_write' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer. Considering that I2C
transfers are generally limited, and that devices used on USB has a
max data length of 64 bytes for the control URBs.
So, it seem safe to use 64 bytes as the hard limit for all those devices.
On most cases, the limit is a way lower than that, but this limit
is small enough to not affect the Kernel stack, and it is a no brain
limit, as using smaller ones would require to either carefully each
driver or to take a look on each datasheet.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Dynamic static allocation is evil, as Kernel stack is too low, and
compilation complains about it on some archs:
drivers/media/dvb-frontends/s5h1420.c:851:1: warning: 's5h1420_tuner_i2c_tuner_xfer' uses dynamic stack allocation [enabled by default]
Instead, let's enforce a limit for the buffer.
In the specific case of this frontend, only ttpci uses it. The maximum
number of messages there is two, on I2C read operations. As the logic
can add an extra operation, change the size to 3.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Use R820T config for R828D too as those are about same tuner.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxk_hard.c:1086:62: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxk_hard.c:2784:63: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/dvb-frontends/drxd_hard.c:1017:70: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:1038:69: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2836:33: warning: Using plain integer as NULL pointer
drivers/media/dvb-frontends/drxd_hard.c:2972:30: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
These aren't necessary after switch and while statements.
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch will fix the situation where the mutex was left in a
locked state if for some reason the FE init failed.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for the cx24117 dual DVB-S/S2 frontend.
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Changeset 9e8da9e8 added a parameter to specify the frequency
divisor, used by the driver. However, not all places are passing
this parameter. So, preserve the previous default, to avoid breaking
the existing drivers.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When the tuner part of the ds3000 driver was split to share code with the m88rs2000 driver, the ts2020 driver used
the frequency divider value from the m88rs2000 driver. However the ds3000 driver requires a different value, and this
resulted in some frequecies being invisible to the tuner. This patch adds back in the value needed for the ds3000 driver
and configured as an option in the dw2102 frontend driver.
It may also apply to su3000 devices, which use the same ds3000 driver, but for now it is only applied to the s660 device.
Signed-off-by: John Horan <knasher@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Make sure that a format string cannot accidentally
leak into the printk buffer.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
SIZEOF_ARRAY is not used (anymore). Besides, ARRAY_SIZE, defined in
include/linux/kernel.h, should be used rather than explicitly coding some
variant of it.
Signed-off-by: Christoph Jaeger <christophjaeger@linux.com>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Reading firmware status register to detect whether firmware is
running or not didn't work 100% reliably. That register was
likely set by firmware itself which means it could not contain
reasonable values until firmware is up and running. Usually it
just worked as some garbage value was returned accidentally but it
appears that in some cases returned garbage value was 0x00 which
was considered "firmware is up and running" by the driver and
firmware loading was skipped leaving device to non-working state.
Fix problem by removing unreliable check and let the driver keep
count whether firmware is loaded or not.
Signed-off-by: Andreas Matthies <a.matthies@gmx.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
changeset 768e6dadd7 caused a regression on using mb86a20s
in parallel mode, as the parallel mode selection got
overriden by mb86a20s_init2.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series contain:
- new i2c video drivers: ml86v7667 (video decoder),
ths8200 (video encoder)
- a new video driver for EasyCap cards based on Fushicai USBTV007
- Improved support for OF and embedded systems, with V4L2 async
initialization and a better support for clocks
- API cleanups on the ioctls used by the v4l2 debug tool
- Lots of cleanups
- As usual, several driver improvements and new cards additions
- Revert two changesets that change the minimal symbol rate for
stv0399, as request by Manu
- Update MAINTAINERS and other files to point to my new e-mail"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (378 commits)
MAINTAINERS & ABI: Update to point to my new email
[media] stb0899: restore minimal rate to 5Mbauds
[media] exynos4-is: Correct colorspace handling at FIMC-LITE
[media] exynos4-is: Set valid initial format on FIMC.n subdevs
[media] exynos4-is: Set valid initial format on FIMC-IS-ISP subdev pads
[media] exynos4-is: Fix format propagation on FIMC-IS-ISP subdev
[media] exynos4-is: Set valid initial format at FIMC-LITE
[media] exynos4-is: Fix format propagation on FIMC-LITE.n subdevs
[media] MAINTAINERS: Update S5P/Exynos FIMC driver entry
[media] Documentation: Update driver's directory in video4linux/fimc.txt
[media] exynos4-is: Change fimc-is firmware file names
[media] exynos4-is: Add support for Exynos5250 MIPI-CSIS
[media] exynos4-is: Add Exynos5250 SoC support to fimc-lite driver
[media] exynos4-is: Drop drvdata handling in fimc-lite for non-dt platforms
[media] media: i2c: tvp514x: remove manual setting of subdev name
[media] media: i2c: tvp7002: remove manual setting of subdev name
[media] mem2mem: set missing v4l2_dev pointer
[media] wl128x: add missing struct v4l2_device
[media] tvp514x: Fix init seqeunce
[media] saa7134: Fix sparse warnings by adding __user annotation
...
According with Manu Abraham, stb0899 seek algorithm is broken
for symbol rates bellow to 5Mbauds. So, revert those patches:
55b3318 [media] stb0899: allow minimum symbol rate of 2000000
2eeed77 [media] stb0899: allow minimum symbol rate of 1000000
Requested-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is no longer needed since the core now handles this through DBG_G_CHIP_INFO.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are a few cases where breaking the code into separate
lines make it worse to read. However, on several places,
breaking it to make checkpatch.pl happier is OK and improves
code readability.
So, break longer lines where that won't cause harm.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
There are several places where: state->var = (some_var)
The parenthesis there are doing nothing but making it
harder to read and breaking the 80 columns soft limits.
Just get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Almost all 80-col warnings are related to comments. There's
one, however, that it is due to a one-line enum declaration
for enum agc_ctrl_mode.
Break it into one line per enumered data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
The comments markup language used on Kernel is defined at:
Documentation/kernel-doc-nano-HOWTO.txt
Remove invalid markups from the header file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Fixes the following checkpatch.pl warnings:
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(10);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+ msleep(1);
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
replace all occurrences of printk(KERN_* by
pr_info/pr_warn/pr_err/pr_debug/pr_cont macros.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Thare are lots of CamelCase warnings produced by checkpatch.pl.
This weren't fixed at the time the driver got submitted due
to the lack of manpower do to such cleanup.
Now that I have one script that automates this task, cleans
it. That makes the driver almost checkpatch-compliant,
except for 80 column warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
X-Patchwork-Delegate: mchehab@redhat.com
Log10 routine is already defined at dvb_math.h and provides a good
enough approximation for 100 x log10(). So, instead of reinventing
the wheel, use the already existing function.
While here, don't use CamelCase on the function name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For consistency, it is necessary to use the autodetected inversion
instead of the configured one.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In non S2 mode, the device is able to autodetect inversion. So
let's store it for tuning to S2 transponders.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Usually, inversion doesn't change in a system. Storing the last
successful inversion value speeds up tuning of DVB-S2 transponders.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like product datasheets for tuners containing STB0899 are
suggesting specification for min. symbol rate of 2MS/s.
Some specs found here, all suggesting 2MS/s for min. symbol rate:
Comtech DVBS2-6899
http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
TechniSat SkyStar HD2
http://www.scaistar.com/skystar2/skystarhd2.htm
Azurewave AD-SP400
http://www.pulsat.com/products/AzureWave-AD%252dSP400-High-Definition-PC-Card.html
New patch:
This makes minimum symbol rate driver capabilities on par with some
accessible datasheet specifications*, and allows tuning on linux to
transponders that have symbol rate between 2000000-5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (2000000 < symbol rate < 5000000):
* DVB/S 12507050 V 2532000 3/4
* DVB/S2 12574000 V 4355000 3/4 8PSK
* DVB/S 12593000 V 2500000 2/3
* DVB/S 12596940 V 2848000 2/3
* DVB/S 12600750 V 2500000 1/2
* DVB/S 12675590 H 4248000 3/4
(*) Datasheet: http://comtech.sg1002.myweb.hinet.net/pdf/dvbs2-6899.pdf
Maximum Symbol Rate
QPSK/LDPC/PCH: 20-30Mbps
8PSK/LDPC/BCH: 10-30Mbps
DVB: 2-45Mbps
^--------- min. symbol rate
Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Throughout the zig-zag-implementations, inversion is taken into
account when reading and writing the CFR register, which contains
the derotator frequency. As swapping IQ signals changes the sign
of that register for example, the idea is to compensate that sign
change by multiplying the register value with the inversion enum
value.
The current enum values 0 and 1 for IQ_SWAP_OFF and IQ_SWAP_ON
don't work in the case IQ_SWAP_OFF, due to the multiplication by
zero (I've only found a single device which actually uses
IQ_SWAP_OFF in it's config).
I've changed the enum values to +1 and -1 to accommodate to the
intended usage.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It seems that current inversion handling addresses only the signal
routing on the PCB, i. e. IQ signals are either swapped or not.
But when the device is operated in a Satellite Channel Router (SCR)
environment, an additional inversion is required due to the way how
the SCR works. Therefore it makes sense to me to always enable auto
inversion handling and drop the enum value IQ_SWAP_AUTO.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes minimum symbol rate driver capabilities on par with
windows driver, and allows tuning on linux to transponders that
have symbol rate below 5000000, too.
Patch was tested successfully on Eutelsat 16A transponders that
became reachable with it (1000000 < symbol rate < 5000000):
* DVB/S 12507050 V 2532000 3/4
* DVB/S2 12574000 V 4355000 3/4 8PSK
* DVB/S 12593000 V 2500000 2/3
* DVB/S 12596940 V 2848000 2/3
* DVB/S 12600750 V 2500000 1/2
* DVB/S 12675590 H 4248000 3/4
Signed-off-by: Zoran Turalija <zoran.turalija@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Contrary to the chip's specs, the register's value is signed, so we
need to sign extend the value before using it in calculations like
when determining the offset frequency.
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb-frontends/dib8000.c: In function ‘dib8000_set_frontend’:
drivers/media/dvb-frontends/dib8000.c:3556: warning: ‘ret’ is used uninitialized in this function
Remove the variable and return zero instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes check for EPERM in dbg_g/s_register
as this check is already performed by core.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The check if the values for c, h and n are within the range is
always true, as, if one of this values is out of range, the
previous "if" clauses will default to a value within the
range.
That fixes the following warning:
drivers/media/dvb-frontends/dib0090.c: In function 'dib0090_set_EFUSE':
drivers/media/dvb-frontends/dib0090.c:1545:5: warning: comparison is always true due to limited range of data type [-Wtype-limits]
and makes the code easier to read.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
