Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/993162
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
as the start can be called after stop again, we need to reset state
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
during pause the core should maintain the status-quo on the device and pointers
and not wake up. If app needs it should call DROP explcitly.
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCI ID entries of Creative SoundCore3D HD-audio controllers should
be before the wildcard for vendor = Creative.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When VGA_SWITCHEROO support is enabled hda_intel initialises the HDMI
audio device on the current VGA device. When it's not enabled it only
initialises the HDMI device on the default VGA adaptor, this means
secondary cards get no audio support which is very unhelpful for
multi-seat!
With this patch, when SUPPORT_VGA_SWITCHEROO is disabled hda_intel
initialises all HDMI audio devices, not just the default VGA.
[minor optimizations by tiwai]
Signed-off-by: Steven Newbury <steve@snewbury.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When VGA-switcheroo is built in but unused on systems with multiple
graphics cards, the initializations of non-default graphics cards are
skipped and never enabled (because the switcheroo is activated only
when the controller supports). The current behavior is for avoiding
the system lockup by accessing the disabled GPU, but due to the recent
change in VGA-switcheroo, it determines the state simply by checking
with the default VGA device. This is the culprit.
Now with the new vga_switcheroo_get_client_state(), we can know the
initial state of the bound GPU, thus can determine the initial audio
client state more correctly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In 3.5 kernel, the endpoint is assigned dynamically for the
substreams, but the PCM assignment still checks the presence of the
endpoint pointer. This ended up in duplicated PCM substream creations
at probing time, resulting in kernel warnings like:
WARNING: at fs/proc/generic.c:586 proc_register+0x169/0x1a6()
Pid: 1152, comm: modprobe Not tainted 3.5.0-rc1-00110-g71fae7e #2
Call Trace:
[<ffffffff8102a400>] warn_slowpath_common+0x83/0x9c
[<ffffffff8102a4bc>] warn_slowpath_fmt+0x46/0x48
[<ffffffff813829ad>] ? add_preempt_count+0x39/0x3b
[<ffffffff811292f0>] proc_register+0x169/0x1a6
[<ffffffff8112962e>] create_proc_entry+0x74/0x8c
[<ffffffffa018eb63>] snd_info_register+0x3e/0xc3 [snd]
[<ffffffffa01fde2e>] snd_pcm_new_stream+0xb1/0x404 [snd_pcm]
[<ffffffffa024861f>] snd_usb_add_audio_stream+0xd2/0x230 [snd_usb_audio]
[<ffffffffa0241d33>] ? snd_usb_parse_audio_format+0x252/0x34f [snd_usb_audio]
[<ffffffff810d6b17>] ? kmem_cache_alloc_trace+0xab/0xbb
[<ffffffffa0248c29>] snd_usb_parse_audio_interface+0x4ac/0x567 [snd_usb_audio]
[<ffffffffa023f0ff>] snd_usb_create_stream+0xe9/0x125 [snd_usb_audio]
[<ffffffffa023f9b1>] usb_audio_probe+0x62a/0x72c [snd_usb_audio]
.....
This patch fixes the regression by checking the fixed endpoint number
for each substream instead of the endpoint pointer.
Reported-and-tested-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows the module to automatically load when instantiated from
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than having varying timeouts depending on the transition always
use a 4s timeout. This provides better diagnostics for clocking errors
and ensures compatibility with current calibration firmwares.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should only add source widgets to the input list.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure that the dpcm_get_be() only returns BE DAI links.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Volume updates may not be acted upon if there is no clock applied when
the volume update is written. Ensure this doesn't happen by writing out
registers with volume updates after we enable each of the clocks.
There are more registers updated than before as previously we were
relying on wm_hubs to set those for controls it manages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Ensure that all the actions get taken at appropriate times by calling the
_PRE and _POST events for the aifNclk_ev functions explicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we check the correct path for capture.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Small driver-specific updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Ch46
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: A few bug fixes for the merge window
Small driver-specific updates.
On PCI RME MADI cards, the PLL register does not contain the proper
value, so the calculated system_sample_rate is wrong. In this case, we
simply return the cached rate from struct hdspm.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The array of sample rates is reallocated every time when opening
the PCM device, but was freed only once when unplugging the device.
Reported-by: "Alexander E. Patrakov" <patrakov@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
FSI DMAEngine has to be stopped certainly at the start/stop time.
Without this patch, it will include noise on playback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
FSI driver is using dma_sync_single_xxx(),
but the dma area was not correct.
This patch fix it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DMA stream handler didn't care about master clock.
This patch fixes it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
This is the second updates for 3.5-rc1. It's mainly for OMAP4 HDMI
updates and the device tree updates for OMAP, in addition to a couple
of PCM accuray improvement and Realtek ALC269VD codec support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=88ho
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound update from Takashi Iwai:
"This is the second updates for 3.5-rc1. It's mainly for OMAP4 HDMI
updates and the device tree updates for OMAP, in addition to a couple
of PCM accuray improvement and Realtek ALC269VD codec support."
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek - Add new codec support for ALC269VD
ALSA: core: group read of pointer, tstamp and jiffies
ASoC: OMAP: HDMI: Rename sound card source file
ASoC: OMAP: HDMI: Make sound card naming more generic
ASoC: OMAP: HDMI: Make build config options more generic
ASoC: OMAP: HDMI: Expand capabilities of the HDMI DAI
ASoC: OMAP: HDMI: Improve how the display state is verified
ASoC: OMAP: HDMI: Expand configuration of hw_params
ASoC: OMAP: HDMI: Use the DSS audio interface
ASoC: OMAP: HDMI: Create a structure for private data of the CPU DAI
ASoC: OMAP: HDMI: Change error values in HDMI CPU DAI
ASoC: OMAP: HDMI: Update the platform device names
ASoC: omap-abe-twl6040: Introduce driver data for runtime parameters
ASoC: omap-abe-twl6040: Move Digital Mic widget into dapm table
ASoC: omap-abe-twl6040: Keep only one snd_soc_dai_link structure
ASoC: omap-dmic: Add device tree bindings
ASoC: omap-mcpdm: Add device tree bindings
ASoC: omap-mcbsp: buffer size constraint only applies to playback stream
ASoC: omap-mcbsp: Use the common interrupt line if supported by the SoC
ASoC: omap-mcbsp: Remove unused FRAME dma_op_mode
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=to5n
-----END PGP SIGNATURE-----
Merge tag 'hda-switcheroo' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull VGA-switcheroo audio client support for HD-audio from Takashi Iwai.
This depended on the recent drm pull.
* tag 'hda-switcheroo' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - unlock on error in azx_interrupt()
ALSA: hda - Support VGA-switcheroo
ALSA: hda - Export snd_hda_lock_devices()
ALSA: hda - Check the dead HDMI audio controller by vga-switcheroo
- Fix mismatch between DMA mapping direction (was wrong) and DMA synchronization
direction (was correct) of isochronous reception buffers of userspace drivers
if vma-mapped for R/W access. For example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and improved
failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in firewire-sbp2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=fulr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates from Stefan Richter:
- Fix mismatch between DMA mapping direction (was wrong) and DMA
synchronization direction (was correct) of isochronous reception
buffers of userspace drivers if vma-mapped for R/W access. For
example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and
improved failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in
firewire-sbp2
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: document the absence of alignment requirements
firewire: sbp2: remove superfluous blk_queue_max_segment_size() call
firewire: sbp2: use scsi_dma_(un)map
firewire: sbp2: give correct DMA device to scsi framework
firewire: core: fw_device_refresh(): clean up error handling
firewire: core: log config rom reading errors
firewire: core: log error in case of failed bus manager lock
firewire: move rcode_string() to core
firewire: core: improve reread_config_rom() interface
firewire: core: wait for inaccessible devices after bus reset
firewire: ohci: omit spinlock IRQ flags where possible
firewire: ohci: correct signedness of a local variable
firewire: core: fix DMA mapping direction
firewire: use module_pci_driver
Pull media updates from Mauro Carvalho Chehab:
- some V4L2 API updates needed by embedded devices
- DVB API extensions for ATSC-MH delivery system, used in US for mobile
TV
- new tuners for fc0011/0012/0013 and tua9001
- a new dvb driver for af9033/9035
- a new ATSC-MH frontend (lg2160)
- new remote controller keymaps
- Removal of a few legacy webcam driver that got replaced by gspca on
several kernel versions ago
- a new driver for Exynos 4/5 webcams(s5pp fimc-lite)
- a new webcam sensor driver (smiapp)
- a new video input driver for embedded (sta2x1xx)
- several improvements, fixes, cleanups, etc inside the drivers.
Manually fix up conflicts due to err() -> dev_err() conversion in
drivers/staging/media/easycap/easycap_main.c
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (484 commits)
[media] saa7134-cards: Remove a PCI entry added by mistake
[media] radio-sf16fmi: add support for SF16-FMD
[media] rc-loopback: remove duplicate line
[media] patch for Asus My Cinema PS3-100 (1043:48cd)
[media] au0828: Move the Kconfig knob under V4L_USB_DRIVERS
[media] em28xx: simple comment fix
[media] [resend] radio-sf16fmr2: add PnP support for SF16-FMD2
[media] smiapp: Use v4l2_ctrl_new_int_menu() instead of v4l2_ctrl_new_custom()
[media] smiapp: Add support for 8-bit uncompressed formats
[media] smiapp: Allow generic quirk registers
[media] smiapp: Use non-binning limits if the binning limit is zero
[media] smiapp: Initialise rval in smiapp_read_nvm()
[media] smiapp: Round minimum pre_pll up rather than down in ip_clk_freq check
[media] smiapp: Use 8-bit reads only before identifying the sensor
[media] smiapp: Quirk for sensors that only do 8-bit reads
[media] smiapp: Pass struct sensor to register writing commands instead of i2c_client
[media] smiapp: Allow using external clock from the clock framework
[media] zl10353: change .read_snr() to report SNR as a 0.1 dB
[media] media: add support to gspca/pac7302.c for 093a:2627 (Genius FaceCam 300)
[media] m88rs2000 - only flip bit 2 on reg 0x70 on 16th try
...
This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten
for the better support of "implicit feedback". If anything about USB
got broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up immediately
at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital links
between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid the accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal routing
through components with tight sequencing and formatting constraints
within their internal paths or where there are multiple components
connected with CPU managed DMA controllers inside the SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like digital
basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124, Texas
Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be
sent slightly later as partly depending on the changes of DRM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQIcBAABAgAGBQJPvD/9AAoJEGwxgFQ9KSmkPsIP/AuBGpAZy7b7FiEEIy1Hhdws
US8WVuPzyDslMVdzZ8OFqyPXanIcL9gscoOGMZOEy7UFtMBiR4GuYiPRPubEMxuP
/gopUqK4SqIsIwT238qqYszSJSxE7gNEZ/2jhSGtkX4EkaSZ4bAskn0iOKX5uw2f
kTUQknA1rNLIGba2z6rJbgIW7hdxGfpFy05ruv3ct81nO+5JlgyLuP/v5R6jL+do
cum0N4dJFRd9YSEi2BG612gdz8LJyzOgPqBKmxMEva6BfqLkR8EdP80FtE3eEOiP
Et1q2LhZwOlBt0BEjsjjOVxMsgxVax6ps9cuNRTk5ECEOldU5dbDatC45L/e9mSD
OQVUjYAX1mQAtYva4U4PPn6WU6ma2L5yjy4peCObtyCMkEchXk1bfs4CEfVqCXUP
yFYN8C+y6osZOyWE3+Enn9ifZdWyLeSVq6CT33Yt+fyKlswp6gRkhKYiEPqTA5aU
p71X59Pp7q1y3tQwiMJNpf2QdkxuxfKURHswdc4BS9ct0mdZhQX0GyDS7OffkTd4
Lq5UkVMHA1rLlF9oRPd2C9P4BuMEuvLjf662YCKiw+mWFYdBC036DHLLjm1Hcwuj
UkpQ2PSrrdHG1u0c3ooZ9dQj1BNX4LoABLqvaMtce6sESD/hJ5gcprYJWvtituwM
ZzZiJavIWsoJ+SWQWBHe
=+JSm
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"This is the first big chunk for 3.5 merges of sound stuff.
There are a few big changes in different areas. First off, the
streaming logic of USB-audio endpoints has been largely rewritten for
the better support of "implicit feedback". If anything about USB got
broken, this change has to be checked.
For HD-audio, the resume procedure was changed; instead of delaying
the resume of the hardware until the first use, now waking up
immediately at resume. This is for buggy BIOS.
For ASoC, dynamic PCM support and the improved support for digital
links between off-SoC devices are major framework changes.
Some highlights are below:
* HD-audio
- Avoid accesses of invalid pin-control bits that may stall the codec
- V-ref setup cleanups
- Fix the races in power-saving code
- Fix the races in codec cache hashes and connection lists
- Split some common codes for BIOS auto-parser to hda_auto_parser.c
- Changed the PM resume code to wake up immediately for buggy BIOS
- Creative SoundCore3D support
- Add Conexant CX20751/2/3/4 codec support
* ASoC
- Dynamic PCM support, allowing support for SoCs with internal
routing through components with tight sequencing and formatting
constraints within their internal paths or where there are multiple
components connected with CPU managed DMA controllers inside the
SoC.
- Greatly improved support for direct digital links between off-SoC
devices, providing a much simpler way of connecting things like
digital basebands to CODECs.
- Much more fine grained and robust locking, cleaning up some of the
confusion that crept in with multi-component.
- CPU support for nVidia Tegra 30 I2S and audio hub controllers and
ST-Ericsson MSP I2S controolers
- New CODEC drivers for Cirrus CS42L52, LAPIS Semiconductor ML26124,
Texas Instruments LM49453.
- Some regmap changes needed by the Tegra I2S driver.
- mc13783 audio support.
* Misc
- Rewrite with module_pci_driver()
- Xonar DGX support for snd-oxygen
- Improvement of packet handling in snd-firewire driver
- New USB-endpoint streaming logic
- Enhanced M-audio FTU quirks and relevant cleanups
- Increment the support of OSS devices to 256
- snd-aloop accuracy improvement
There are a few more pending changes for 3.5, but they will be sent
slightly later as partly depending on the changes of DRM."
Fix up conflicts in regmap (due to duplicate patches, with some further
updates then having already come in from the regmap tree). Also some
fairly trivial context conflicts in the imx and mcx soc drivers.
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (280 commits)
ALSA: snd-usb: fix stream info output in /proc
ALSA: pcm - Add proper state checks to snd_pcm_drain()
ALSA: sh: Fix up namespace collision in sh_dac_audio.
ALSA: hda/realtek - Fix unused variable compile warning
ASoC: sh: fsi: enable chip specific data transfer mode
ASoC: sh: fsi: call fsi_hw_startup/shutdown from fsi_dai_trigger()
ASoC: sh: fsi: use same format for IN/OUT
ASoC: sh: fsi: add fsi_version() and removed meaningless version check
ASoC: sh: fsi: use register field macro name on IN/OUT_DMAC
ASoC: tegra: Add machine driver for WM8753 codec
ALSA: hda - Fix possible races of accesses to connection list array
ASoC: OMAP: HDMI: Introduce codec
ARM: mx31_3ds: Add sound support
ASoC: imx-mc13783 cleanup
mx31moboard: Add sound support
ASoC: mc13783 codec cleanups
ASoC: add imx-mc13783 sound support
ASoC: Add mc13783 codec
mfd: mc13xxx: add codec platform data
ASoC: don't flip master of DT-instantiated DAI links
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
Group read of hw_ptr, tstamp and jiffies in a sequence
for better correlation. Previous code took timestamp at the
end, which could introduce delays between audio time and
system time.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Rename sound card driver source file to encompass not only OMAP4 but future
OMAP versions that feature HDMI.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Rename all the relevant structures, variables and functions to not
make specific reference to OMAP4. This is to make the driver encompass
future OMAP versions that feature HDMI and not only OMAP4. These
changes are only in naming. There are not functional changes.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Make Kconfig and Makefile more generic to encompass not only
OMAP4 but other OMAP processors featuring HDMI.
Also, relax the dependency list to depend only on any OMAP processor
supporting OMAP2_DSS and OMAP4_DSS_HDMI. As HDMI support for
future OMAP versions is added, the dependency list must change
accordingly.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
According to the HDMI specification, a source is permitted to
transmit L-PCM audio in the following sample rates: 32kHz, 44.1kHz,
48kHz, 88.2kHz, 96kHz, 176.4kHz or 192kHz.
It also supports up to 8 audio channels.
The sink may not necessarily support all these sample rates and
channels. However, as this CPU DAI describes the HDMI source, it
makes sense to include them. The limitation of capabilities as
supported by the sink should be done in the ASoC HDMI codec.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Before starting to play audio, we need to make sure that the
display is active and the current video mode supports audio. instead
of using the overlay manager in the machine driver, we use the DSS audio
interface's audio_supported function. As we already have a pointer to
the correct dssdev, we do not have to look for it every time audio is
to be played. Also, the CPU DAI startup function is called earlier
than the card hw_param function. Hence and we can detect the state of
the display earlier.
While there, add a error message if the constraint cannot be applied.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
squash to improve err
Signed-off-by: Liam Girdwood <lrg@ti.com>
Expand the configuration of the hw_params to include the IEC-60958
channel status word and the CEA-861 audio infoframe. The configuration
of such structures depends on the snd_pcm_hw_params received. A
omap_dss_audio is used to pass the configuration parameters to DSS.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Instead of accessing the HDMI IP directly, the CPU DAI driver takes
advantage of the audio interface provided by the DSS device driver.
The ASoC driver will link the DSS audio functionality with ALSA by
calling the appropriate DSS device driver functions at the relevant
moments. For this, three new DAI operations are added: trigger, prepare
and shutdown operations.
At the moment, it is assumed that only one HDMI display is available
in the system, as it is the case in OMAP4. However, in the future,
one DAI for each HDMI display should be provided.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Create a struct hdmi_priv to store the relevant data of the CPU DAI
driver. As more data is added to the driver, having all the data
in the same location eases its handling. At the moment, only the DMA
configuration parameters are included in the structure.
Also, the required memory is allocated using devm_kzalloc rather than
using a static global variable.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
When getting the needed resources fails, return -ENODEV. This is more
in line with other drivers do and it gives a more descriptive error.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In order to utilize the new OMAP HDMI codec and the updated name of
the device of the CPU DAI, update the names at the drivers accordingly.
While there, also update the name of the machine driver to be more
generic and encompass more OMAP processors featuring HDMI and not
only OMAP4.
Signed-off-by: Ricardo Neri <ricardo.neri@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In preparation to Device Tree support.
With DT booted kernel we can not rely on pdata which used to
hold information needed for the driver at runtime.
Use the card's driver data to hold these informations from now on.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
The needed change in routing will be done runtime for the non
twl6040 connected widgets, like the Digital microphone.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
There is no need to have two snd_soc_dai_link structure for the two setup
the machine driver supports.
We can just tell core to register only the first link if the DMIC link is
not in use on the device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ dmic cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
Device tree support for OMAP4+ McPDM cpu dai driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
In capture stream the buffer size does not need to be constrained to be
bigger then the McBSP FIFO.
In capture the FIFO content is taken out in period length burst, this
enusres that the FIFO is not going to overflow.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Liam Girdwood <lrg@ti.com>
