- add debugfs support for dumping dma-debug information (Corentin Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
-----BEGIN PGP SIGNATURE-----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=nAMI
-----END PGP SIGNATURE-----
Merge tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping
Pull DMA mapping updates from Christoph Hellwig:
- add debugfs support for dumping dma-debug information (Corentin
Labbe)
- Kconfig cleanups (Andy Shevchenko and me)
- debugfs cleanups (Greg Kroah-Hartman)
- improve dma_map_resource and use it in the media code
- arch_setup_dma_ops / arch_teardown_dma_ops cleanups
- various small cleanups and improvements for the per-device coherent
allocator
- make the DMA mask an upper bound and don't fail "too large" dma mask
in the remaning two architectures - this will allow big driver
cleanups in the following merge windows
* tag 'dma-mapping-5.1' of git://git.infradead.org/users/hch/dma-mapping: (21 commits)
Documentation/DMA-API-HOWTO: update dma_mask sections
sparc64/pci_sun4v: allow large DMA masks
sparc64/iommu: allow large DMA masks
sparc64: refactor the ali DMA quirk
ccio: allow large DMA masks
dma-mapping: remove the DMA_MEMORY_EXCLUSIVE flag
dma-mapping: remove dma_mark_declared_memory_occupied
dma-mapping: move CONFIG_DMA_CMA to kernel/dma/Kconfig
dma-mapping: improve selection of dma_declare_coherent availability
dma-mapping: remove an incorrect __iommem annotation
of: select OF_RESERVED_MEM automatically
device.h: dma_mem is only needed for HAVE_GENERIC_DMA_COHERENT
mfd/sm501: depend on HAS_DMA
dma-mapping: add a kconfig symbol for arch_teardown_dma_ops availability
dma-mapping: add a kconfig symbol for arch_setup_dma_ops availability
dma-mapping: move debug configuration options to kernel/dma
dma-debug: add dumping facility via debugfs
dma: debug: no need to check return value of debugfs_create functions
videobuf2: replace a layering violation with dma_map_resource
dma-mapping: don't BUG when calling dma_map_resource on RAM
...
Core changes:
- The big change this time around is the irqchip handling in
the qualcomm pin controllers, closely coupled with the
gpiochip. This rework, in a classic fall-between-the-chairs
fashion has been sidestepped for too long. The Qualcomm
IRQchips using the SPMI and SSBI transport mechanisms have
been rewritten to use hierarchical irqchip. This creates
the base from which I intend to gradually pull support for
hierarchical irqchips into the gpiolib irqchip helpers to
cut down on duplicate code. We have too many hacks in the
kernel because people have been working around the missing
hierarchical irqchip for years, and once it was there,
noone understood it for a while. We are now slowly adapting
to using it. This is why this pull requests include changes
to MFD, SPMI, IRQchip core and some ARM Device Trees
pertaining to the Qualcomm chip family. Since Qualcomm have
so many chips and such large deployments it is paramount
that this platform gets this right, and now it (hopefully)
does.
- Core support for pull-up and pull-down configuration, also
from the device tree. When a simple GPIO chip support a
"off or on" pull-up or pull-down resistor, we provide a
way to set this up using machine descriptors or device tree.
If more elaborate control of pull up/down (such as
resistance shunt setting) is required, drivers should be
phased over to use pin control. We do not yet provide a
userspace ABI for this pull up-down setting but I suspect
the makers are going to ask for it soon enough. PCA953x
is the first user of this new API.
- The GPIO mockup driver has been revamped after some
discussion improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for
both testing and virtual prototyping, e.g. when you do
not yet have a GPIO expander to play with but really
want to get something to develop code around before
hardware is available. It's neat. The blackbox testing
usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating
flags.
- A new device core helper for devm_platform_ioremap_resource()
is funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped
I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum
driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers.
-----BEGIN PGP SIGNATURE-----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=VoVC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.1 cycle:
Core changes:
- The big change this time around is the irqchip handling in the
qualcomm pin controllers, closely coupled with the gpiochip. This
rework, in a classic fall-between-the-chairs fashion has been
sidestepped for too long.
The Qualcomm IRQchips using the SPMI and SSBI transport mechanisms
have been rewritten to use hierarchical irqchip. This creates the
base from which I intend to gradually pull support for hierarchical
irqchips into the gpiolib irqchip helpers to cut down on duplicate
code.
We have too many hacks in the kernel because people have been
working around the missing hierarchical irqchip for years, and once
it was there, noone understood it for a while. We are now slowly
adapting to using it.
This is why this pull requests include changes to MFD, SPMI,
IRQchip core and some ARM Device Trees pertaining to the Qualcomm
chip family. Since Qualcomm have so many chips and such large
deployments it is paramount that this platform gets this right, and
now it (hopefully) does.
- Core support for pull-up and pull-down configuration, also from the
device tree. When a simple GPIO chip supports an "off or on" pull-up
or pull-down resistor, we provide a way to set this up using
machine descriptors or device tree.
If more elaborate control of pull up/down (such as resistance shunt
setting) is required, drivers should be phased over to use pin
control. We do not yet provide a userspace ABI for this pull
up-down setting but I suspect the makers are going to ask for it
soon enough. PCA953x is the first user of this new API.
- The GPIO mockup driver has been revamped after some discussion
improving the IRQ simulator in the process.
The idea is to make it possible to use the mockup for both testing
and virtual prototyping, e.g. when you do not yet have a GPIO
expander to play with but really want to get something to develop
code around before hardware is available. It's neat. The blackbox
testing usecase is currently making its way into kernelci.
- ACPI GPIO core preserves non direction flags when updating flags.
- A new device core helper for devm_platform_ioremap_resource() is
funneled through the GPIO tree with Greg's ACK.
New drivers:
- TQ-Systems QTMX86 GPIO controllers (using port-mapped I/O)
- Gateworks PLD GPIO driver (vaccumed up from OpenWrt)
- AMD G-Series PCH (Platform Controller Hub) GPIO driver.
- Fintek F81804 & F81966 subvariants.
- PCA953x now supports NXP PCAL6416.
Driver improvements:
- IRQ support on the Nintendo Wii (Hollywood) GPIO.
- get_direction() support for the MVEBU driver.
- Set the right output level on SAMA5D2.
- Drop the unused irq trigger setting on the Spreadtrum driver.
- Wakeup support for PCA953x.
- A slew of cleanups in the various Intel drivers"
* tag 'gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (110 commits)
gpio: gpio-omap: fix level interrupt idling
gpio: amd-fch: Set proper output level for direction_output
x86: apuv2: remove unused variable
gpio: pca953x: Use PCA_LATCH_INT
platform/x86: fix PCENGINES_APU2 Kconfig warning
gpio: pca953x: Fix dereference of irq data in shutdown
gpio: amd-fch: Fix type error found by sparse
gpio: amd-fch: Drop const from resource
gpio: mxc: add check to return defer probe if clock tree NOT ready
gpio: ftgpio: Register per-instance irqchip
gpio: ixp4xx: Add DT bindings
x86: pcengines apuv2 gpio/leds/keys platform driver
gpio: AMD G-Series PCH gpio driver
drivers: depend on HAS_IOMEM for devm_platform_ioremap_resource()
gpio: tqmx86: Set proper output level for direction_output
gpio: sprd: Change to use SoC compatible string
gpio: sprd: Use SoC compatible string instead of wildcard string
gpio: of: Handle both enable-gpio{,s}
gpio: of: Restrict enable-gpio quirk to regulator-gpio
gpio: davinci: use devm_platform_ioremap_resource()
...
As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP,
NVIDIA, Amlogic and Qualcomm.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+DOl
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"As usual, the drivers/tee and drivers/reset subsystems get merged
here, with the expected set of smaller updates and some new hardware
support. The tee subsystem now supports device drivers to be attached
to a tee, the first example here is a random number driver with its
implementation in the secure world.
Three new power domain drivers get added for specific chip families:
- Broadcom BCM283x chips (used in Raspberry Pi)
- Qualcomm Snapdragon phone chips
- Xilinx ZynqMP FPGA SoCs
One new driver is added to talk to the BPMP firmware on NVIDIA
Tegra210
Existing drivers are extended for new SoC variants from NXP, NVIDIA,
Amlogic and Qualcomm"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (113 commits)
tee: optee: update optee_msg.h and optee_smc.h to dual license
tee: add cancellation support to client interface
dpaa2-eth: configure the cache stashing amount on a queue
soc: fsl: dpio: configure cache stashing destination
soc: fsl: dpio: enable frame data cache stashing per software portal
soc: fsl: guts: make fsl_guts_get_svr() static
hwrng: make symbol 'optee_rng_id_table' static
tee: optee: Fix unsigned comparison with less than zero
hwrng: Fix unsigned comparison with less than zero
tee: fix possible error pointer ctx dereferencing
hwrng: optee: Initialize some structs using memset instead of braces
tee: optee: Initialize some structs using memset instead of braces
soc: fsl: dpio: fix memory leak of a struct qbman on error exit path
clk: tegra: dfll: Make symbol 'tegra210_cpu_cvb_tables' static
soc: qcom: llcc-slice: Fix typos
qcom: soc: llcc-slice: Consolidate some code
qcom: soc: llcc-slice: Clear the global drv_data pointer on error
drivers: soc: xilinx: Add ZynqMP power domain driver
firmware: xilinx: Add APIs to control node status/power
dt-bindings: power: Add ZynqMP power domain bindings
...
This API is primarily used through DT entries, but two architectures
and two drivers call it directly. So instead of selecting the config
symbol for random architectures pull it in implicitly for the actual
users. Also rename the Kconfig option to describe the feature better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/mfd/mxs-lradc.c: In function ‘mxs_lradc_probe’:
drivers/mfd/mxs-lradc.c:179:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (lradc->soc == IMX28_LRADC) {
^
drivers/mfd/mxs-lradc.c:185:3: note: here
default:
^~~~~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cleanup the formatting to have consistent style across the file (only
white-space issues). No expected difference in code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The QMX86 is a PLD present on some TQ-Systems ComExpress modules. It
provides 1 or 2 I2C bus masters, 8 GPIOs and a watchdog timer. Add an
MFD which will instantiate the individual drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We now using a common macro for PM operations in Intel LPSS driver,
and, since that macro relies on the definition and macro from linux/pm.h
header file, it's logical to include it directly in intel-lpss.h.
Otherwise it's a bit fragile and requires a proper ordering
of header inclusion in C files.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
-----BEGIN PGP SIGNATURE-----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=t5+u
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom ARM/ARM64/MIPS based SoCs changes
for 5.1, please pull the following:
- Stefan updates the BCM2835 SoC driver with downstream properties and
uses that to implement a reboot notifier to tell the VC4 firmware when
Linux on the ARM CPU is rebooting
- Eric adds a proper power domain driver for the BCM283x SoCs and
updates a bunch of drivers to have a better and clearer Device Tree
definition to support power domains/breaking up of functionality. This
requires converting the existing watchdog driver into a MFD and then
breaking up the functionality into separate drivers and finally
updating the DTS files to leverage the power domains information.
- Wei provides a fix for making a symbol static
* tag 'arm-soc/for-5.1/drivers' of https://github.com/Broadcom/stblinux:
ARM: bcm283x: Switch V3D over to using the PM driver instead of firmware.
ARM: bcm283x: Extend the WDT DT node out to cover the whole PM block. (v4)
soc: bcm: bcm2835-pm: Make local symbol static
soc: bcm: Make PM driver default for BCM2835
soc: bcm: bcm2835-pm: Add support for power domains under a new binding.
bcm2835-pm: Move bcm2835-watchdog's DT probe to an MFD.
dt-bindings: soc: Add a new binding for the BCM2835 PM node. (v4)
firmware: raspberrypi: notify VC4 firmware of a reboot
soc: bcm2835: sync firmware properties with downstream
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Select IRQ_DOMAIN_HIERARCHY for pm8xxx in Kconfig since this driver uses
the version 2 IRQ interfaces. IRQ_DOMAIN_HIERARCHY selects IRQ_DOMAIN,
so it can be removed from here.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the sm501 mfd driver can be compiled without any dependencies,
but through the use of dma_declare_coherent it really depends on
having DMA and iomem support. Normally we don't explicitly require DMA
support as we have stubs for it if on UML, but in this case the driver
selects support for dma_declare_coherent and thus also requires
memmap support. Guard this by an explicit dependency.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Now that ssbi-gpio is a proper hierarchical IRQ chip, and all in-tree
users of device tree have been updated, we can now drop the hack that
was introduced to disassociate the old Linux virq if a hwirq mapping
already exists. That patch was introduced to not break git bisect for
any existing boards.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Check to see if the hwirq is already associated with another virq on
this IRQ domain. If so, then disassociate it before associating the
hwirq with the new virq.
This is a temporary hack that is needed in order to not break git
bisect for existing boards. The next patch in this series converts
ssbi-gpio to be a hierarchical IRQ chip, then there are several patches
to update all of the device tree files, and finally this patch will be
reverted within the same patch series.
IRQs for ssbi-gpio are all initially setup without an IRQ hierarchy
this driver is probed due to the interrupts property in device tree.
Once ssbi-gpio is converted to be a hierarchical IRQ chip in the next
patch, existing users of gpio[d]_to_irq() will call pmic_gpio_to_irq(),
and that will use the new IRQ chip code in ssbi-gpio that sets up the
IRQ in an IRQ hierarchy. The hwirq is now associated with two Linux
virqs and interrupts will not work as expected. This patch corrects
that issue.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the PM8XXX IRQ code to use the version 2 IRQ interface in order
to support hierarchical IRQ chips. This is necessary so that ssbi-gpio
can be setup as a hierarchical IRQ chip with PM8xxx as the parent. IRQ
chips in device tree should be usable from the start without having to
make an additional call to gpio[d]_to_irq() to get the proper IRQ on the
parent.
pm8821_irq_domain_ops and pm8821_irq_domain_map are removed by this
patch since the irq_chip is now contained in the pm_irq_data struct, and
that allows us to use a common IRQ mapping function.
This change was tested on an APQ8060 DragonBoard.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While ioctls normally return a negative error or 0 on success, this is not
the case for CROS_EC_DEV_IOCXCMD in the cros_ec driver, which returns the
number of bytes read instead. However, CROS_EC_DEV_IOCRDMEM in the same
driver does not return the number of byte read on success. This is both
inconsistent and problematic, since the amount of returned data can be
dynamic. Have it return the number of data bytes for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_TPS68470
drivers/mfd/Kconfig: bool "TI TPS68470 Power Management / LED chips"
...meaning that it currently is not being built as a module by anyone.
Hence we remove the MODULE_DEVICE_TABLE since it is a no-op for
non-modular code.
There is no removal of <linux/module.h> here because there isn't one.
Instead, it is relying on including that implicitly from an ACPI header.
In cleaning up the ACPI instance of module.h (which also isn't strictly
needed), then this mfd driver breaks when MODULE_DEVICE_TABLE becomes
undefined here.
The easiest dependency solution is to simply defer the ACPI cleanup
until this change is present in mainline.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
They are never get changed, make them constant.
While at it, fix indent as well.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Lochnagar is an evaluation and development board for Cirrus
Logic Smart CODEC and Amp devices. It allows the connection of
most Cirrus Logic devices on mini-cards, as well as allowing
connection of various application processor systems to provide a
full evaluation platform. This driver supports the board
controller chip on the Lochnagar board. Audio system topology,
clocking and power can all be controlled through the Lochnagar
controller chip, allowing the device under test to be used in
a variety of possible use cases.
As the Lochnagar is a fairly complex device this MFD driver
allows the drivers for the various features to be bound
in. Initially clocking, regulator and pinctrl will be added as
these are necessary to configure the system. But in time at least
audio and voltage/current monitoring will also be added.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Replace impossible BUG() in probe with a proper return. This can be
triggered only in case of a clear bug (e.g. adding broken half-support
for new S2MPSXX flavor) but BUG() is discouraged and the boot process
can actually try to continue.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a potential NULL pointer dereference in case devm_kzalloc()
fails and returns NULL.
Fix this by adding a NULL check on *lookup*
This bug was detected with the help of Coccinelle.
Fixes: b2e6355559 ("i2c: gpio: Convert to use descriptors")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
INTEL_SOC_PMIC, INTEL_SOC_PMIC_CHTWC and MFD_TPS68470 select the
I2C_DESIGNWARE_PLATFORM without its dependencies making it possible to see
warning and build error like below:
WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
Selected by [y]:
- MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_resume':
i2c-designware-platdrv.c:(.text+0x62): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_suspend':
i2c-designware-platdrv.c:(.text+0x9a): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: drivers/i2c/busses/i2c-designware-platdrv.o: in function `dw_i2c_plat_probe':
i2c-designware-platdrv.c:(.text+0x41c): undefined reference to `i2c_dw_prepare_clk'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x438): undefined reference to `i2c_dw_read_comp_param'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x545): undefined reference to `i2c_dw_probe'
/usr/bin/ld: i2c-designware-platdrv.c:(.text+0x727): undefined reference to `i2c_dw_probe_slave'
Fix this by making above options to depend on I2C_DESIGNWARE_PLATFORM
being built-in. I2C_DESIGNWARE_PLATFORM is a visible symbol with
dependencies so in general the select should be avoided.
Fixes: acebcff9ed ("mfd: intel_soc_pmic: Select designware i2c-bus driver")
Fixes: de85d79f4a ("mfd: Add Cherry Trail Whiskey Cove PMIC driver")
Fixes: 9bbf6a15ce ("mfd: Add support for TPS68470 device")
Cc: Stable <stable@vger.kernel.org> # v4.14+
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Lee Jones <lee.jones@linaro.org>
These options apply to all regulators in this chip.
ti,strict-supply-voltage-supervision:
Set STRICT flag in CONFIG1
ti,under-voltage-limit-microvolt:
Select 2.75, 2.95, 3.25 or 3.35 V UVLO in CONFIG1
ti,under-voltage-hyst-microvolt:
Select 200mV or 400mV UVLOHYS in CONFIG2
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_WM8400
drivers/mfd/Kconfig: bool "Wolfson Microelectronics WM8400"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
A trivial function rename from wm8400_module_init to the name
wm8400_driver_init is also done to reduce possible confusion.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_WM8350
drivers/mfd/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Previous demodularizaion work has made wm8350_device_exit() no longer
used, so it is also removed from the 8350 core code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_WM8350_I2C
drivers/mfd/Kconfig: bool "Wolfson Microelectronics WM8350 with I2C"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
But we do delete an unused moduleparam.h
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_WM831X
drivers/mfd/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Previous demodularizaion work has made wm831x_device_exit() no longer
used, so it is also removed from the 831x core code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_WM831X_I2C
drivers/mfd/Kconfig: bool "Wolfson Microelectronics WM831x/2x PMICs with I2C"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_WM831X_SPI
drivers/mfd/Kconfig: bool "Wolfson Microelectronics WM831x/2x PMICs with SPI"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_TPS80031
drivers/mfd/Kconfig: bool "TI TPS80031/TPS80032 Power Management chips"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_TPS65910
drivers/mfd/Kconfig- bool "TI TPS65910 Power Management chip"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We do delete an unused moduleparam.h include though.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_TPS65090
drivers/mfd/Kconfig: bool "TI TPS65090 Power Management chips"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_SYSCON
drivers/mfd/Kconfig: bool "System Controller Register R/W Based on Regmap"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_STA2X11
drivers/mfd/Kconfig: bool "STMicroelectronics STA2X11"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Davide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_RC5T583
drivers/mfd/Kconfig: bool "Ricoh RC5T583 Power Management system device"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_MAX8925
drivers/mfd/Kconfig: bool "Maxim Semiconductor MAX8925 PMIC Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig for this option is currently:
config HTC_I2CPLD
bool "HTC I2C PLD chip support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_DB8500_PRCMU
drivers/mfd/Kconfig: bool "ST-Ericsson DB8500 Power Reset Control Management Unit"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_AS3711
drivers/mfd/Kconfig: bool "AMS AS3711"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Makefile/Kconfig currently controlling compilation of this code is:
drivers/mfd/Makefile:obj-$(CONFIG_PMIC_ADP5520) += adp5520.o
drivers/mfd/Kconfig:config PMIC_ADP5520
drivers/mfd/Kconfig: bool "Analog Devices ADP5520/01 MFD PMIC Core Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_AAT2870_CORE
drivers/mfd/Kconfig: bool "AnalogicTech AAT2870"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The cros-ec-vbc driver is DT-only and there is a DT property that
indicates if the EC has the VCB NVRAM, in such case instantiate the
driver but don't instantiate on the other cases.
To do this move the check code to its parent instead of play with the
attribute group visibility. This changes a bit the actual behaviour.
Before the patch if an EC doesn't have a VBC NVRAM an empty vbc folder
is created in /sys/class/chromeos/<ec-device-name>, after the patch the
empty folder is not created, so, the folder is only created if the vbc
is set.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros debugfs attibutes are created is broken.
cros_ec_sysfs should be its own driver and its attributes should be
associated with the sysfs driver not the mfd driver.
The patch also adds the sysfs documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros debugfs attibutes are created is broken.
cros_ec_debugfs should be its own driver and its attributes should be
associated with a debugfs driver not the mfd driver.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros sysfs attibutes are created is broken.
cros_ec_vbc should be its own driver and its attributes should be
associated with a vbc driver not the mfd driver. In order to retain
the path, the vbc attributes are attached to the cros_class.
The patch also adds the sysfs documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The entire way how cros sysfs attibutes are created is broken.
cros_ec_lightbar should be its own driver and its attributes should be
associated with a lightbar driver not the mfd driver. In order to retain
the path, the lightbar attributes are attached to the cros_class.
The patch also adds the sysfs documentation.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
