commit ff097ddd4 (x86/PCI: MMCONFIG: manage pci_mmcfg_region as a
list, not a table) introduced a nasty memory corruption when
pci_mmcfg_list is empty.
pci_mmcfg_check_end_bus_number() dereferences pci_mmcfg_list.prev even
when the list is empty. The following write hits some variable near to
pci_mmcfg_list.
Further down a similar problem exists, where cfg->list.next is
dereferenced unconditionally and a comparison with some variable near
to pci_mmcfg_list happens.
Add a check for the last element into the for_each_entry() loop and
remove all the other crappy logic which is just a leftover of the old
array based code which was replaced by the list conversion.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The code in stop_machine that modifies the kernel text has a bit
of logic to handle the case of NMIs. stop_machine does not prevent
NMIs from executing, and if an NMI were to trigger on another CPU
as the modifying CPU is changing the NMI text, a GPF could result.
To prevent the GPF, the NMI calls ftrace_nmi_enter() which may
modify the code first, then any other NMIs will just change the
text to the same content which will do no harm. The code that
stop_machine called must wait for NMIs to finish while it changes
each location in the kernel. That code may also change the text
to what the NMI changed it to. The key is that the text will never
change content while another CPU is executing it.
To make the above work, the call to ftrace_nmi_enter() must also
do a smp_mb() as well as atomic_inc(). But for applications like
perf that require a high number of NMIs for profiling, this can have
a dramatic effect on the system. Not only is it doing a full memory
barrier on both nmi_enter() as well as nmi_exit() it is also
modifying a global variable with an atomic operation. This kills
performance on large SMP machines.
Since the memory barriers are only needed when ftrace is in the
process of modifying the text (which is seldom), this patch
adds a "modifying_code" variable that gets set before stop machine
is executed and cleared afterwards.
The NMIs will check this variable and store it in a per CPU
"save_modifying_code" variable that it will use to check if it
needs to do the memory barriers and atomic dec on NMI exit.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Distros generally (I looked at Debian, RHEL5 and SLES11) seem to
enable CONFIG_HIGHPTE for any x86 configuration which has highmem
enabled. This means that the overhead applies even to machines which
have a fairly modest amount of high memory and which therefore do not
really benefit from allocating PTEs in high memory but still pay the
price of the additional mapping operations.
Running kernbench on a 4G box I found that with CONFIG_HIGHPTE=y but
no actual highptes being allocated there was a reduction in system
time used from 59.737s to 55.9s.
With CONFIG_HIGHPTE=y and highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 175.396 (0.238914)
User Time 515.983 (5.85019)
System Time 59.737 (1.26727)
Percent CPU 263.8 (71.6796)
Context Switches 39989.7 (4672.64)
Sleeps 42617.7 (246.307)
With CONFIG_HIGHPTE=y but with no highmem PTEs being allocated:
Average Optimal load -j 4 Run (std deviation):
Elapsed Time 174.278 (0.831968)
User Time 515.659 (6.07012)
System Time 55.9 (1.07799)
Percent CPU 263.8 (71.266)
Context Switches 39929.6 (4485.13)
Sleeps 42583.7 (373.039)
This patch allows the user to control the allocation of PTEs in
highmem from the command line ("userpte=nohigh") but retains the
status-quo as the default.
It is possible that some simple heuristic could be developed which
allows auto-tuning of this option however I don't have a sufficiently
large machine available to me to perform any particularly meaningful
experiments. We could probably handwave up an argument for a threshold
at 16G of total RAM.
Assuming 768M of lowmem we have 196608 potential lowmem PTE
pages. Each page can map 2M of RAM in a PAE-enabled configuration,
meaning a maximum of 384G of RAM could potentially be mapped using
lowmem PTEs.
Even allowing generous factor of 10 to account for other required
lowmem allocations, generous slop to account for page sharing (which
reduces the total amount of RAM mappable by a given number of PT
pages) and other innacuracies in the estimations it would seem that
even a 32G machine would not have a particularly pressing need for
highmem PTEs. I think 32G could be considered to be at the upper bound
of what might be sensible on a 32 bit machine (although I think in
practice 64G is still supported).
It's seems questionable if HIGHPTE is even a win for any amount of RAM
you would sensibly run a 32 bit kernel on rather than going 64 bit.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
LKML-Reference: <1266403090-20162-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This will save 64K bytes from memory when loading linux if DMI is
disabled, which is good for embedded systems.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
LKML-Reference: <1265758732-19320-1-git-send-email-cascardo@holoscopio.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
init_fpu() already ensures that the used_math() is set for the stopped child.
Remove the redundant set_stopped_child_used_math() in [x]fpregs_set()
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100222225240.642169080@sbs-t61.sc.intel.com>
Acked-by: Rolan McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
48 bytes (bytes 464..511) of the xstateregs payload come from the
kernel defined structure (xstate_fx_sw_bytes). Rest comes from the
xstate regs structure in the thread struct. Instead of having multiple
user_regset_copyout()'s, simplify the xstateregs_get() by first
copying the SW bytes into the xstate regs structure in the thread structure
and then using one user_regset_copyout() to copyout the xstateregs.
Requested-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100222225240.494688491@sbs-t61.sc.intel.com>
Acked-by: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Oleg Nesterov <oleg@redhat.com>
The main benefit of using ACPI host bridge window information is that
we can do better resource allocation in systems with multiple host bridges,
e.g., http://bugzilla.kernel.org/show_bug.cgi?id=14183
Sometimes we need _CRS information even if we only have one host bridge,
e.g., https://bugs.launchpad.net/ubuntu/+source/linux/+bug/341681
Most of these systems are relatively new, so this patch turns on
"pci=use_crs" only on machines with a BIOS date of 2008 or newer.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Previously we used a table of size PCI_BUS_NUM_RESOURCES (16) for resources
forwarded to a bus by its upstream bridge. We've increased this size
several times when the table overflowed.
But there's no good limit on the number of resources because host bridges
and subtractive decode bridges can forward any number of ranges to their
secondary buses.
This patch reduces the table to only PCI_BRIDGE_RESOURCE_NUM (4) entries,
which corresponds to the number of windows a PCI-to-PCI (3) or CardBus (4)
bridge can positively decode. Any additional resources, e.g., PCI host
bridge windows or subtractively-decoded regions, are kept in a list.
I'd prefer a single list rather than this split table/list approach, but
that requires simultaneous changes to every architecture. This approach
only requires immediate changes where we set up (a) host bridges with more
than four windows and (b) subtractive-decode P2P bridges, and we can
incrementally change other architectures to use the list.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Merge reason:
Conflicts in arch/x86/kernel/apic/io_apic.c
Resolved Conflicts:
arch/x86/kernel/apic/io_apic.c
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Merge reason: conflict in arch/x86/kernel/apic/io_apic.c
Resolved Conflicts:
arch/x86/kernel/apic/io_apic.c
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On VIVT ARM, when we have multiple shared mappings of the same file
in the same MM, we need to ensure that we have coherency across all
copies. We do this via make_coherent() by making the pages
uncacheable.
This used to work fine, until we allowed highmem with highpte - we
now have a page table which is mapped as required, and is not available
for modification via update_mmu_cache().
Ralf Beache suggested getting rid of the PTE value passed to
update_mmu_cache():
On MIPS update_mmu_cache() calls __update_tlb() which walks pagetables
to construct a pointer to the pte again. Passing a pte_t * is much
more elegant. Maybe we might even replace the pte argument with the
pte_t?
Ben Herrenschmidt would also like the pte pointer for PowerPC:
Passing the ptep in there is exactly what I want. I want that
-instead- of the PTE value, because I have issue on some ppc cases,
for I$/D$ coherency, where set_pte_at() may decide to mask out the
_PAGE_EXEC.
So, pass in the mapped page table pointer into update_mmu_cache(), and
remove the PTE value, updating all implementations and call sites to
suit.
Includes a fix from Stephen Rothwell:
sparc: fix fallout from update_mmu_cache API change
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The code for setting standard VGA modes probes for the current mode,
and skips the mode setting if the mode is 3 (color text 80x25) or 7
(mono text 80x25). Unfortunately, there are BIOSes, including the
VMware BIOS, which report the previous mode if function 0F is queried
while the screen is in a VESA mode, and of course, nothing can help a
mode poked directly into the hardware.
As such, the safe option is to set the mode anyway, and only query to
see if we should be using mode 7 rather than mode 3. People who don't
want any mode setting at all should probably use vga=0x0f04
(VIDEO_CURRENT_MODE). It's possible that should be the kernel
default.
Reported-by Rene Arends <R.R.Arends@hro.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
When the user enables breakpoints through dr7, he can choose
between "local" or "global" enable bits but given how linux is
implemented, both have the same effect.
That said we don't keep track how the user enabled the breakpoints
so when the user requests the dr7 value, we only translate the
"enabled" status using the global enabled bits. It means that if
the user enabled a breakpoint using the local enabled bit, reading
back dr7 will set the global bit and clear the local one.
Apps like Wine expect a full dr7 POKEUSER/PEEKUSER match for emulated
softwares that implement old reverse engineering protection schemes.
We fix that by keeping track of the whole dr7 value given by the user
in the thread structure to drop this bug. We'll think about
something more proper later.
This fixes a 2.6.32 - 2.6.33-x ptrace regression.
Reported-and-tested-by: Michael Stefaniuc <mstefani@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Maneesh Soni <maneesh@linux.vnet.ibm.com>
Cc: Alexandre Julliard <julliard@winehq.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Before we had a generic breakpoint API, ptrace was accepting
breakpoints on NULL address in x86. The new API refuse them,
without given strong reasons. We need to follow the previous
behaviour as some userspace apps like Wine need such NULL
breakpoints to ensure old emulated software protections
are still working.
This fixes a 2.6.32 - 2.6.33-x ptrace regression.
Reported-and-tested-by: Michael Stefaniuc <mstefani@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: K.Prasad <prasad@linux.vnet.ibm.com>
Acked-by: Roland McGrath <roland@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Maneesh Soni <maneesh@linux.vnet.ibm.com>
Cc: Alexandre Julliard <julliard@winehq.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Inhibit output from the kernel decompressor if the video information
is invalid. This was already the case for 32 bits, make 64 bits
match.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
Final stage linking can fail with
arch/x86/built-in.o: In function `store_cache_disable':
intel_cacheinfo.c:(.text+0xc509): undefined reference to `amd_get_nb_id'
arch/x86/built-in.o: In function `show_cache_disable':
intel_cacheinfo.c:(.text+0xc7d3): undefined reference to `amd_get_nb_id'
when CONFIG_CPU_SUP_AMD is not enabled because the amd_get_nb_id
helper is defined in AMD-specific code but also used in generic code
(intel_cacheinfo.c). Reorganize the L3 cache index disable code under
CONFIG_CPU_SUP_AMD since it is AMD-only anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100218184210.GF20473@aftab>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The show/store_cache_disable routines depend unnecessarily on NUMA's
cpu_to_node and the disabling of cache indices broke when !CONFIG_NUMA.
Remove that dependency by using a helper which is always correct.
While at it, enable L3 Cache Index disable on rev D1 Istanbuls which
sport the feature too.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100218184339.GG20473@aftab>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Version 4: use get_irq_chip_data() in destroy_irq() to get rid of some
local vars.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20100207210250.GB8256@jenkins.home.ifup.org>
Signed-off-by: Brandon Phiilps <bphilips@suse.de>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When we restore the screen content after a mode change, we return the
cursor to its former position. However, we need to also update
boot_params.screen_info accordingly, so that the decompression code
knows where on the screen the cursor is. Just in case the video BIOS
does something extra screwy, read the cursor position back from the
BIOS instead of relying on it doing the right thing.
While we're at it, make sure we cap the cursor position to the new
screen coordinates.
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Bugzilla-Reference: http://bugzilla.kernel.org/show_bug.cgi?id=15329
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On x86, before prefill_possible_map(), nr_cpu_ids will be NR_CPUS aka
CONFIG_NR_CPUS.
Add nr_cpus= to set nr_cpu_ids. so we can simulate cpus <=8 are installed on
normal config.
-v2: accordging to Christoph, acpi_numa_init should use nr_cpu_ids in stead of
NR_CPUS.
-v3: add doc in kernel-parameters.txt according to Andrew.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-34-git-send-email-yinghai@kernel.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Tony Luck <tony.luck@intel.com>
So keep nr_irqs == NR_IRQS. With radix trees is matters less.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-33-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This is a fix for bug #14845 (bugzilla.kernel.org). The update_checksum()
function in mm/kmemleak.c calls kmemcheck_is_obj_initialised() before scanning
an object. When KMEMCHECK_PARTIAL_OK is enabled, this function returns true.
However, the crc32_le() reads smaller intervals (32-bit) for which
kmemleak_is_obj_initialised() may be false leading to a kmemcheck warning.
Note that kmemcheck_is_obj_initialized() is currently only used by
kmemleak before scanning a memory location.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Cc: Vegard Nossum <vegardno@ifi.uio.no>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
x86/mm is on 32-rc4 and missing the spinlock namespace changes which
are needed for further commits into this topic.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
KPROBES_EVENT actually depends on the regs and stack access API
(b1cf540f) and not on x86.
So introduce a new config option which architectures can select if
they have the API implemented and switch x86.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20100210162517.GB6933@osiris.boeblingen.de.ibm.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Most implementations of arch_syscall_addr() are the same, so create a
default version in common code and move the one piece that differs (the
syscall table) to asm/syscall.h. New arch ports don't have to waste
time copying & pasting this simple function.
The s390/sparc versions need to be different, so document why.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <1264498803-17278-1-git-send-email-vapier@gentoo.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
On the iMac9,1 /sbin/reboot results in a black mangled screen. Adding
this DMI entry gets the machine to reboot cleanly as it should.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
LKML-Reference: <1266362249-3337-1-git-send-email-justinmattock@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This makes the range reservation feature available to other
architectures.
-v2: add get_max_mapped, max_pfn_mapped only defined in x86...
to fix PPC compiling
-v3: according to hpa, add CONFIG_HAVE_EARLY_RES
-v4: fix typo about EARLY_RES in config
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B7B5723.4070009@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For some reason the 64-bit tree was doing this differently and
I can't see why it would need to.
This correct behaviour when you have two GPUs plugged in and
32-bit put the console in one place and 64-bit in another.
Signed-off-by: Dave Airlie <airlied@redhat.com>
LKML-Reference: <1262847894-27498-1-git-send-email-airlied@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The 64-bit version of ELF_PLAT_INIT() clears TIF_IA32, but at this point
it has already been cleared by SET_PERSONALITY == set_personality_64bit.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The atomic ops emulation for 32bit legacy CPUs floods the tracer with
irq off/on entries. The irq disabled regions are short and therefor
not interesting when chasing long irq disabled latencies. Mark them
raw and keep them out of the trace.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We realized when we broke acpi=ht
http://bugzilla.kernel.org/show_bug.cgi?id=14886
that acpi=ht is not needed on this box
and folks have been using acpi=force on it anyway.
Signed-off-by: Len Brown <len.brown@intel.com>
Fixes bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=12558
Fixes bugzilla: http://bugzilla.kernel.org/show_bug.cgi?id=12317
(and if this really needed to be a warn you'd be responding to the bugs left
in bugzilla from it...)
Signed-off-by: Alan Cox <alan@linux.intel.com>
LKML-Reference: <20100208100239.2568.2940.stgit@localhost.localdomain>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Now that numa=fake=<size>[MG] is implemented, it is possible to remove
configurable node size support. The command-line parsing was already
broken (numa=fake=*128, for example, would not work) and since fake nodes
are now interleaved over physical nodes, this support is no longer
required.
Signed-off-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1002151343080.26927@chino.kir.corp.google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
numa=fake=N specifies the number of fake nodes, N, to partition the
system into and then allocates them by interleaving over physical nodes.
This requires knowledge of the system capacity when attempting to
allocate nodes of a certain size: either very large nodes to benchmark
scalability of code that operates on individual nodes, or very small
nodes to find bugs in the VM.
This patch introduces numa=fake=<size>[MG] so it is possible to specify
the size of each node to allocate. When used, nodes of the size
specified will be allocated and interleaved over the set of physical
nodes.
FAKE_NODE_MIN_SIZE was also moved to the more-appropriate
include/asm/numa_64.h.
Signed-off-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1002151342510.26927@chino.kir.corp.google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
numa=fake=N uses split_nodes_interleave() to partition the system into N
fake nodes. Each node size must have be a multiple of
FAKE_NODE_MIN_SIZE, otherwise it is possible to get strange alignments.
Because of this, the remaining memory from each node when rounded to
FAKE_NODE_MIN_SIZE is consolidated into a number of "big nodes" that are
bigger than the rest.
The calculation of the number of big nodes is incorrect since it is using
a logical AND operator when it should be multiplying the rounded-off
portion of each node with N.
Signed-off-by: David Rientjes <rientjes@google.com>
LKML-Reference: <alpine.DEB.2.00.1002151342230.26927@chino.kir.corp.google.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch adds code to cpu initialization path to detect
the extended virtualization features of AMD cpus to show
them in /proc/cpuinfo.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <1260792521-15212-1-git-send-email-joerg.roedel@amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Intel Architecture Optimization Reference Manual states that a short
load that follows a long store to the same object will suffer a store
forwading penalty, particularly if the two accesses use different addresses.
Trivially, a long load that follows a short store will also suffer a penalty.
__downgrade_write() in rwsem incurs both penalties: the increment operation
will not be able to reuse a recently-loaded rwsem value, and its result will
not be reused by any recently-following rwsem operation.
A comment in the code states that this is because 64-bit immediates are
special and expensive; but while they are slightly special (only a single
instruction allows them), they aren't expensive: a test shows that two loops,
one loading a 32-bit immediate and one loading a 64-bit immediate, both take
1.5 cycles per iteration.
Fix this by changing __downgrade_write to use the same add instruction on
i386 and on x86_64, so that it uses the same operand size as all the other
rwsem functions.
Signed-off-by: Avi Kivity <avi@redhat.com>
LKML-Reference: <1266049992-17419-1-git-send-email-avi@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
... so we can move early_res up.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-27-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
... in preparation of moving early_res to kernel/.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-26-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Let's make 32bit consistent with 64bit.
-v2: Andrew pointed out for 32bit that we should use -1ULL
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-25-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
... to make it always try to start from low at first.
This makes it less likely for early_memtest to reserve a bad range, in
particular it puts new early_res in a range that is already tested.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-24-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Makes early_res.c more clean, so later could move it to /kernel.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-23-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare to move bck find_e820_area_size back to e820.c.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-22-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
... to make e820.c smaller.
-v2: fix 32bit compiling with MAX_DMA32_PFN
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-21-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
So prepare to make one more clean of early_res.c.
-v2: don't need to reserve first page in early_res
because we already mark that in e820 as reserved already.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-20-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add vmemmap_alloc_block_buf for mem map only.
It will fallback to the old way if it cannot get a block that big.
Before this patch, when a node have 128g ram installed, memmap are
split into two parts or more.
[ 0.000000] [ffffea0000000000-ffffea003fffffff] PMD -> [ffff880100600000-ffff88013e9fffff] on node 1
[ 0.000000] [ffffea0040000000-ffffea006fffffff] PMD -> [ffff88013ec00000-ffff88016ebfffff] on node 1
[ 0.000000] [ffffea0070000000-ffffea007fffffff] PMD -> [ffff882000600000-ffff8820105fffff] on node 0
[ 0.000000] [ffffea0080000000-ffffea00bfffffff] PMD -> [ffff882010800000-ffff8820507fffff] on node 0
[ 0.000000] [ffffea00c0000000-ffffea00dfffffff] PMD -> [ffff882050a00000-ffff8820709fffff] on node 0
[ 0.000000] [ffffea00e0000000-ffffea00ffffffff] PMD -> [ffff884000600000-ffff8840205fffff] on node 2
[ 0.000000] [ffffea0100000000-ffffea013fffffff] PMD -> [ffff884020800000-ffff8840607fffff] on node 2
[ 0.000000] [ffffea0140000000-ffffea014fffffff] PMD -> [ffff884060a00000-ffff8840709fffff] on node 2
[ 0.000000] [ffffea0150000000-ffffea017fffffff] PMD -> [ffff886000600000-ffff8860305fffff] on node 3
[ 0.000000] [ffffea0180000000-ffffea01bfffffff] PMD -> [ffff886030800000-ffff8860707fffff] on node 3
[ 0.000000] [ffffea01c0000000-ffffea01ffffffff] PMD -> [ffff888000600000-ffff8880405fffff] on node 4
[ 0.000000] [ffffea0200000000-ffffea022fffffff] PMD -> [ffff888040800000-ffff8880707fffff] on node 4
[ 0.000000] [ffffea0230000000-ffffea023fffffff] PMD -> [ffff88a000600000-ffff88a0105fffff] on node 5
[ 0.000000] [ffffea0240000000-ffffea027fffffff] PMD -> [ffff88a010800000-ffff88a0507fffff] on node 5
[ 0.000000] [ffffea0280000000-ffffea029fffffff] PMD -> [ffff88a050a00000-ffff88a0709fffff] on node 5
[ 0.000000] [ffffea02a0000000-ffffea02bfffffff] PMD -> [ffff88c000600000-ffff88c0205fffff] on node 6
[ 0.000000] [ffffea02c0000000-ffffea02ffffffff] PMD -> [ffff88c020800000-ffff88c0607fffff] on node 6
[ 0.000000] [ffffea0300000000-ffffea030fffffff] PMD -> [ffff88c060a00000-ffff88c0709fffff] on node 6
[ 0.000000] [ffffea0310000000-ffffea033fffffff] PMD -> [ffff88e000600000-ffff88e0305fffff] on node 7
[ 0.000000] [ffffea0340000000-ffffea037fffffff] PMD -> [ffff88e030800000-ffff88e0707fffff] on node 7
after patch will get
[ 0.000000] [ffffea0000000000-ffffea006fffffff] PMD -> [ffff880100200000-ffff88016e5fffff] on node 0
[ 0.000000] [ffffea0070000000-ffffea00dfffffff] PMD -> [ffff882000200000-ffff8820701fffff] on node 1
[ 0.000000] [ffffea00e0000000-ffffea014fffffff] PMD -> [ffff884000200000-ffff8840701fffff] on node 2
[ 0.000000] [ffffea0150000000-ffffea01bfffffff] PMD -> [ffff886000200000-ffff8860701fffff] on node 3
[ 0.000000] [ffffea01c0000000-ffffea022fffffff] PMD -> [ffff888000200000-ffff8880701fffff] on node 4
[ 0.000000] [ffffea0230000000-ffffea029fffffff] PMD -> [ffff88a000200000-ffff88a0701fffff] on node 5
[ 0.000000] [ffffea02a0000000-ffffea030fffffff] PMD -> [ffff88c000200000-ffff88c0701fffff] on node 6
[ 0.000000] [ffffea0310000000-ffffea037fffffff] PMD -> [ffff88e000200000-ffff88e0701fffff] on node 7
-v2: change buf to vmemmap_buf instead according to Ingo
also add CONFIG_SPARSEMEM_ALLOC_MEM_MAP_TOGETHER according to Ingo
-v3: according to Andrew, use sizeof(name) instead of hard coded 15
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-19-git-send-email-yinghai@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Finally we can use early_res to replace bootmem for x86_64 now.
Still can use CONFIG_NO_BOOTMEM to enable it or not.
-v2: fix 32bit compiling about MAX_DMA32_PFN
-v3: folded bug fix from LKML message below
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4B747239.4070907@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add the xstate regset support which helps extend the kernel ptrace and the
core-dump interfaces to support AVX state etc.
This regset interface is designed to support all the future state that gets
supported using xsave/xrstor infrastructure.
Looking at the memory layout saved by "xsave", one can't say which state
is represented in the memory layout. This is because if a particular state is
in init state, in the xsave hdr it can be represented by bit '0'. And hence
we can't really say by the xsave header wether a state is in init state or
the state is not saved in the memory layout.
And hence the xsave memory layout available through this regset
interface uses SW usable bytes [464..511] to convey what state is represented
in the memory layout.
First 8 bytes of the sw_usable_bytes[464..467] will be set to OS enabled xstate
mask(which is same as the 64bit mask returned by the xgetbv's xCR0).
The note NT_X86_XSTATE represents the extended state information in the
core file, using the above mentioned memory layout.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <20100211195614.802495327@sbs-t61.sc.intel.com>
Signed-off-by: Hongjiu Lu <hjl.tools@gmail.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, apic: Don't use logical-flat mode when CPU hotplug may exceed 8 CPUs
x86-32: Make AT_VECTOR_SIZE_ARCH=2
x86/agp: Fix amd64-agp module initialization regression
x86, doc: Fix minor spelling error in arch/x86/mm/gup.c
64bit NUMA already make enough space under 4G with new early_node_mem.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-16-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Use early_res_count to track the num, and use find_e820 to get a new
buffer, then copy from the old to the new one.
Also, clear early_res to prevent later invalid usage.
-v2 _check_and_double_early_res should take new start
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-14-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
To prepare allocate early res array from fine_e820_area.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-13-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Simplify setup_node_mem: don't use bootmem from other node, instead
just find_e820_area in early_node_mem.
This keeps the boundary between early_res and boot mem more clear, and
lets us only call early_res_to_bootmem() one time instead of for all
nodes.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-12-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
So we can check that early in the bootlog.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-11-git-send-email-yinghai@kernel.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
So make interface more consistent with early_res.
Later we can share some code with early_res.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-10-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Should be good for 32bit too.
-v3: cast res->start
-v4: according to Linus, to use %pR instead of cast
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-9-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare for 32bit pci root bus
-v2: hpa said we should compare with (resource_size_t)~0
-v3: according to Linus to use MAX_RESOURCE instead.
also need need to put related patches together
-v4: according to Andrew, use min in cap_resource()
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-8-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare to enable it for 32bit.
-v2: remove not needed cast
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-7-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Found MSI amd k8 based laptops is hiding [0x70000000, 0x80000000) RAM
from e820.
enable amd one chain even for all.
-v2: use bool for found, according to Andrew
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-6-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Prepare to enable 32bit intel and amd bus.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-5-git-send-email-yinghai@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We have almost the same code for mtrr cleanup and amd_bus checkup, and
this code will also be used in replacing bootmem with early_res,
so try to move them together and reuse it from different parts.
Also rename update_range to subtract_range as that is what the
function is actually doing.
-v2: update comments as Christoph requested
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-4-git-send-email-yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Keep chip_data in create_irq_nr and destroy_irq.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Brandon Phililps <bphilips@suse.de>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
Later all kind of devices fail...
and bisect it down to this commit:
commit b9c61b7007
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de>
Bisected-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Do not set current->mm->mmap to NULL in 32-bit emulation on 64-bit
load_aout_binary after flush_old_exec as it would destroy already
set brpm mapping with arguments.
Introduced by b6a2fea393
mm: variable length argument support
where the argument mapping in bprm was added.
[ hpa: this is a regression from 2.6.22... time to kill a.out? ]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
LKML-Reference: <1265831716-7668-1-git-send-email-jslaby@suse.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ollie Wild <aaw@google.com>
Cc: x86@kernel.org
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When hotadd new cpu to system, if its affinitive node is online,
should map the cpu to its own node. Otherwise, let kernel select one
online node for the new cpu later.
Signed-off-by: Haicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <4B6AAA39.6000300@linux.intel.com>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'kvm-updates/2.6.33' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PIT: control word is write-only
kvmclock: count total_sleep_time when updating guest clock
Export the symbol of getboottime and mmonotonic_to_bootbased
We need to fall back from logical-flat APIC mode to physical-flat mode
when we have more than 8 CPUs. However, in the presence of CPU
hotplug(with bios listing not enabled but possible cpus as disabled cpus in
MADT), we have to consider the number of possible CPUs rather than
the number of current CPUs; otherwise we may cross the 8-CPU boundary
when CPUs are added later.
32bit apic code can use more cleanups (like the removal of vendor checks in
32bit default_setup_apic_routing()) and more unifications with 64bit code.
Yinghai has some patches in works already. This patch addresses the boot issue
that is reported in the virtualization guest context.
[ hpa: incorporated function annotation feedback from Yinghai Lu ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1265767304.2833.19.camel@sbs-t61.sc.intel.com>
Acked-by: Shaohui Zheng <shaohui.zheng@intel.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both x86-32 and x86-64 with 32-bit compat use ARCH_DLINFO_IA32,
which defines two saved_auxv entries. But system.h only defines
AT_VECTOR_SIZE_ARCH as 2 for CONFIG_IA32_EMULATION, not for
CONFIG_X86_32. Fix that.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
LKML-Reference: <20100209023502.GA15408@us.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Current kvm wallclock does not consider the total_sleep_time which could cause
wrong wallclock in guest after host suspend/resume. This patch solve
this issue by counting total_sleep_time to get the correct host boot time.
Cc: stable@kernel.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Glauber Costa <glommer@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] Fix ondemand to not request targets outside policy limits
[CPUFREQ] Fix use after free of struct powernow_k8_data
[CPUFREQ] fix default value for ondemand governor
Fixes these warnings:
arch/x86/kernel/alternative.c: In function 'alternatives_text_reserved':
arch/x86/kernel/alternative.c:402: warning: comparison of distinct pointer types lacks a cast
arch/x86/kernel/alternative.c:402: warning: comparison of distinct pointer types lacks a cast
arch/x86/kernel/alternative.c:405: warning: comparison of distinct pointer types lacks a cast
arch/x86/kernel/alternative.c:405: warning: comparison of distinct pointer types lacks a cast
Caused by:
2cfa197: ftrace/alternatives: Introducing *_text_reserved functions
Changes in v2:
- Use local variables to compare, instead of type casts.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Masami Hiramatsu <mhiramat@redhat.com>
Cc: systemtap <systemtap@sources.redhat.com>
Cc: DLE <dle-develop@lists.sourceforge.net>
LKML-Reference: <20100205171647.15750.37221.stgit@dhcp-100-2-132.bos.redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: x86@kernel.org
LKML-Reference: <1265478443-31072-10-git-send-email-elendil@planet.nl>
[ Left out the KVM bits. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add function to direct Legacy VGA I/O traffic to correct I/O Hub.
Signed-off-by: Mike Travis <travis@sgi.com>
LKML-Reference: <201002022238.o12McEbi018727@imap1.linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Robin Holt <holt@sgi.com>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
io_32.h and io_64.h are now identical. Merge them into io.h.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-8-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Always make it an inline instead of using a macro for the no-op case.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-7-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Iomem has no special significance on x86. Use the standard mem*
functions instead of trying to call other versions. Some fixups
are needed to match the function prototypes.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-6-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Copied from io_32.h.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-5-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make it more similar to io_32.h. No real code changes.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-4-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
These were leftover from the numaq support that was removed in commit
1fba38703d.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-3-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The XQUAD stuff is part of the NUMAQ architecture, so move it there.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-2-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pass the clocksource as an argument to the clocksource resume callback.
Needed so we can point out which CMT channel the sh_cmt.c driver shall
resume.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The last reference to the helpers in
<arch/x86/kernel/cpu/mtrr/state.c> went away with
9a6b344ea9 leaving unused code.
Remove it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <20100204085128.GA513@liondog.tnic>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We cannot assume that because hwc->idx == assign[i], we can avoid
reprogramming the counter in hw_perf_enable().
The event may have been scheduled out and another event may have been
programmed into this counter. Thus, we need a more robust way of
verifying if the counter still contains config/data related to an event.
This patch adds a generation number to each counter on each cpu. Using
this mechanism we can verify reliabilty whether the content of a counter
corresponds to an event.
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <4b66dc67.0b38560a.1635.ffffae18@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
