As documented in Application Note SWPA117 v2.1(NDA), LDO override has a
requirement that when switching from Bias active + override active
mode(FBB/RBB) to Bypass(nominal) mode, LDO reset must be performed
*after* LDO transitions to Bypass(nominal) mode.
The same rule in reverse applies when switching from a ABB bypass mode
to ABB enabled - LDO override *must* be performed prior to transition to
required ABB mode, if we do not do that, the same glitch takes place.
Currently while transitioning to ABB bypass, we reset the LDO overide
prior to the transition which causes a few milliseconds where ABB LDO
voltage could go all the way to 800mV(based on SoC process node),
during this period, the delta voltage between VDD rail and VBB rail
could cause the system to improperly function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Fix the linear range settings in commit 5ff26a14c3
"regulator: wm831x-ldo: Convert to use linear ranges".
For wm831x_gp_ldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xe:
volt = 0.9-1.6V in 50mV steps
sel <= 0x1f:
volt = 1.7-3.3V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
For wm831x_aldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xc:
volt = 1-1.6V in 50mV steps
sel <= 0x1f
volt = 1.7-3.5V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet, voltage range for LDOs are as follows:
0000 = 0.9V
...(50mV steps)
01111 = 1.65V
10000 = 1.8V
... (100mV stepns)
11111 = 3.3V
So, there is no selector for 1.65V to 1.8V.
Correcting the range for max_uV for selector between 0 to 15.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current equation on the comment is wrong.
For linear mapping starting from 0, the equation is (maxV-minV)/stepV + 1.
Since the linear mapping for PALMAS is not all starting from 0, the equation
on the comment is not useful and misleading. Thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If CONFIG_OF=n:
drivers/regulator/da9063-regulator.c: In function ‘da9063_parse_regulators_dt’:
drivers/regulator/da9063-regulator.c:712: warning: passing argument 1 of ‘PTR_ERR’ makes pointer from integer without a cast
drivers/regulator/da9063-regulator.c:712: warning: return makes pointer from integer without a cast
Use ERR_PTR() to encode an error code in a pointer.
PTR_ERR() is meant to decode an error code from a pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet (Referred TPS65913), the on-time for LDO is
500micro second. If LDO6 is in vibrator mode then the on-time
is 2000us.
Set the enable_time on regulator descriptor accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
With the following change
---------
commit ad02e84687
Author: Axel Lin <axel.lin@ingics.com>
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
----------
The list_voltage() takes the true value of selector which is
programmed in the register. As per smsp voltage table
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
121 1650000 (0.49V + 116 * 0.1) * RANGE
Hence making n_voltages for smps to 122.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
da9063_ldo_lim_event() is only referenced in this driver, make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
lp872x regulator driver can be built a module after commit 631a1fc
"regulator: build: Allow most regulators to be built as modules".
Make REGULATOR_LP872X depend on I2C to allow building lp872x module when I2C=m.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Below is the equation in original code:
tps65217_uv1_ranges:
0 ... 24: uV = vsel * 25000 + 900000;
25 ... 52: uV = (vsel - 24) * 50000 + 1500000;
= (vsel - 25) * 50000 + 1550000;
53 ... 55: uV = (vsel - 52) * 100000 + 2900000;
= (vsel - 53) * 100000 + 3000000;
56 ... 62: uV = 3300000;
tps65217_uv2_ranges:
0 ... 8: uV = vsel * 50000 + 1500000;
9 ... 13: uV = (vsel - 8) * 100000 + 1900000;
= (vsel - 9) * 100000 + 2000000;
14 ... 31: uV = (vsel - 13) * 50000 + 2400000;
= (vsel - 14) * 50000 + 2450000;
The voltage tables are composed of linear ranges.
This patch converts this driver to use multiple linear ranges APIs.
In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range
for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in
tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52.
This change makes it possible to reuse the same linear_ranges table for DCDCx.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_register() does not return NULL, it returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All the current limit tables have the values in ascend order.
So we can slightly optimize the for loop iteration because the first match
is the minimal value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver adds support for the following DA9063 PMIC regulators:
- 11x LDOs (named LDO1 - LDO11),
- 6x buck converters (BCORE1, BCORE2, BPRO, BMEM, BIO, BPERI),
Regulators provide following operations:
- REGULATOR_CHANGE_STATUS and REGULATOR_CHANGE_VOLTAGE for all regulators,
- REGULATOR_CHANGE_MODE for LDOs and buck converters, where:
- LDOs allow REGULATOR_MODE_NORMAL and REGULATOR_MODE_STANDBY,
- buck converters allow REGULATOR_MODE_FAST, REGULATOR_MODE_NORMAL
and REGULATOR_MODE_STANDBY,
- REGULATOR_CHANGE_CURRENT for buck converters (current limits).
The driver generates REGULATOR_EVENT_OVER_CURRENT for LDO3, LDO4, LDO7, LDO8
and LDO11.
Internally, PMIC provides two voltage configurations for normal and suspend
system state for each regulator. The driver switches between those on
suspend/wake-up to provide quick and fluent output voltage change.
This driver requires MFD core driver for operation.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is supposed to be testing "i < ARRAY_SIZE()" instead of just
"ARRAY_SIZE()".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The code to check whether num_regulator is valid is wrong because it should
iterate all array entries rather than break from the for loop if
pdata->regulators[i] is NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code has wrong mask and val arguments for updating ramp_delay. Fix it.
Also ensure the return value of get_ramp_delay() won't greater than 3 because
the mask field for ramp_val only takes 2 bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SMPS10 has two outputs OUT1 and OUT2 and have one input IN1.
SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either
in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures
it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be
used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using
regulator_enable().
[ axel.lin@ingics.com : Simplify regulator_desc setting for SMPS10_[OUT1|OUT2]
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move regulator_list_voltage_{linear,linear_range,table} helper functions to
helpers.c.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix a build warning for !CONFIG_OF and a cast from void* to
unsigned int which is invalid on 64bit machines.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I2C driver for the Dialog DA9210 Multi-phase 12A DC-DC Buck.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
