This adds interrupt functionality for i2c chips to the driver.
They can act as a interrupt-controller and generate interrupts, if
the inputs change.
This is tested with a mcp23017 chip on an arm based platform.
v3:
- be a bit more clear that the irq functionality is also available
on spi versions of the chips, but the linux driver does not support
this yet
v2:
- some more word about irq-mirror property in binding doc
- use of_read_bool instead of of_find_property for
"interrupt-contrller" and "irq-mirror"
- cache the "interrupt-controller" for remove function
- do set the irq-mirror bit only if device is marked as
interrupt-controller
- do create the irq mapping and setup of irq_desc of all possible
interrupts in probe path instead of in gpio_to_irq
- mark gpios as in use as interrupts in irq in irq_startup and
unlock it in irq_shutdown
- rename virq to child_irq
- remove dev argument from mcp23s08_irq_setup function
- move gpiochip_add before mcp23s08_irq_setup in probe path
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* pm-cpufreq: (40 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
powernow-k6: reorder frequencies
powernow-k6: correctly initialize default parameters
powernow-k6: disable cache when changing frequency
Documentation: add ABI entry for intel_pstate
cpufreq: exynos: Convert exynos-cpufreq to platform driver
...
Since the support for software and hardware controlled boosting has
been added, update the corresponding documentation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The macb driver uses the clock bindings. Document the required
properties, especially the driver specific clock-names.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Rob Herring <robh@kernel.org>
fix a typo in the "clock specifiers" discussion,
clarify that clock specifiers (the integer cells
part that goes with the phandle) may be empty
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: devicetree@vger.kernel.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Document the multimedia clock controller found on Qualcomm devices
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Document the global clock controller found on Qualcomm devices.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some of Qualcomm's clocks can change their parent and rate at the
same time with a single register write. Add support for this
hardware to the common clock framework by adding a new
set_rate_and_parent() op. When the clock framework determines
that both the parent and the rate are going to change during
clk_set_rate() it will call the .set_rate_and_parent() op if
available and fall back to calling .set_parent() followed by
.set_rate() otherwise.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The cache's policy may have been established using the "default" alias,
which is currently the "mq" policy but the default policy may change in
the future. It is useful to know exactly which policy is being used.
Add a 'real' member to the dm_cache_policy_type structure and have the
"default" dm_cache_policy_type point to the real "mq"
dm_cache_policy_type. Update dm_cache_policy_get_name() to check if
real is set, if so report the name of the real policy (not the alias).
Requested-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
device_type is deprecated. There is no need to check for it in device
driver code and no need to specify it in the device tree. Remove the
property from stock .dts files and remove the check for it from device
drivers. This change should be 100% backwards compatible with old device
trees.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
device_type is deprecated and the kernel doesn't require it in most
cases. The only exceptions for flat tree users are the "gianfar",
"ucc_geth" and "ibm,emac" bindings, and arguably that requirement could
be relaxed for ucc_geth and ibm,emac (that is a task for separate
patches though).
This patch removes references to device_type="network" from the binding
documentation where possible and removes the properties from ARM and
microblaze dts files. This patch does not modify the powerpc .dts files
since there are a much larger number of them affected and I think the
ucc_geth, ibm,emac and gianfar users should be addressed before clearing
out the references to reduce the chance of breakage.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Michal Simek <monstr@monstr.eu>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
device_type is a deprecated property, but some MDIO bus nodes still have
it. Except for a couple of old binding (compatible="gianfar" and
compatible="ucc_geth_phy") the kernel doesn't look for
device_type="mdio" at all.
This patch removes all instances of device_type="mdio" from the binding
documentation and the .dts files.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The linux,phandle property is essentially an internal structural element
of the DT data structure. The dtc toolchain takes care of maintaining it
at compile time. It does not need to appear as part of the binding
documentation. This patch removes it so that users don't think they need
to add a phandle property manually.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
A scheduled horkage patch will conflict with HORKAGE changes in
for-3.13-fixes. Pull in to avoid unnecessary merge conflicts.
Signed-off-by: Tejun Heo <tj@kernel.org>
The device_type property is deprecated for the flattened device tree and
the value "ethernet-phy" has never been defined as having a useful
meaning. Neither the kernel nor u-boot depend on it. It should never
have appeared in PHY bindings. This patch removes all references to
"ethernet-phy" as a device_type value from the documentation and the
.dts files.
This patch was generated mechanically with the following command and
then verified by looking at the diff.
sed -i '/"ethernet-phy"/d' `git grep -l '"ethernet-phy"'`
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When booting a kexec/kdump kernel on a system that has specific memory
hotplug regions the boot will fail with warnings like:
swapper/0: page allocation failure: order:9, mode:0x84d0
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.10.0-65.el7.x86_64 #1
Hardware name: QCI QSSC-S4R/QSSC-S4R, BIOS QSSC-S4R.QCI.01.00.S013.032920111005 03/29/2011
0000000000000000 ffff8800341bd8c8 ffffffff815bcc67 ffff8800341bd950
ffffffff8113b1a0 ffff880036339b00 0000000000000009 00000000000084d0
ffff8800341bd950 ffffffff815b87ee 0000000000000000 0000000000000200
Call Trace:
[<ffffffff815bcc67>] dump_stack+0x19/0x1b
[<ffffffff8113b1a0>] warn_alloc_failed+0xf0/0x160
[<ffffffff815b87ee>] ? __alloc_pages_direct_compact+0xac/0x196
[<ffffffff8113f14f>] __alloc_pages_nodemask+0x7ff/0xa00
[<ffffffff815b417c>] vmemmap_alloc_block+0x62/0xba
[<ffffffff815b41e9>] vmemmap_alloc_block_buf+0x15/0x3b
[<ffffffff815b1ff6>] vmemmap_populate+0xb4/0x21b
[<ffffffff815b461d>] sparse_mem_map_populate+0x27/0x35
[<ffffffff815b400f>] sparse_add_one_section+0x7a/0x185
[<ffffffff815a1e9f>] __add_pages+0xaf/0x240
[<ffffffff81047359>] arch_add_memory+0x59/0xd0
[<ffffffff815a21d9>] add_memory+0xb9/0x1b0
[<ffffffff81333b9c>] acpi_memory_device_add+0x18d/0x26d
[<ffffffff81309a01>] acpi_bus_device_attach+0x7d/0xcd
[<ffffffff8132379d>] acpi_ns_walk_namespace+0xc8/0x17f
[<ffffffff81309984>] ? acpi_bus_type_and_status+0x90/0x90
[<ffffffff81309984>] ? acpi_bus_type_and_status+0x90/0x90
[<ffffffff81323c8c>] acpi_walk_namespace+0x95/0xc5
[<ffffffff8130a6d6>] acpi_bus_scan+0x8b/0x9d
[<ffffffff81a2019a>] acpi_scan_init+0x63/0x160
[<ffffffff81a1ffb5>] acpi_init+0x25d/0x2a6
[<ffffffff81a1fd58>] ? acpi_sleep_proc_init+0x2a/0x2a
[<ffffffff810020e2>] do_one_initcall+0xe2/0x190
[<ffffffff819e20c4>] kernel_init_freeable+0x17c/0x207
[<ffffffff819e18d0>] ? do_early_param+0x88/0x88
[<ffffffff8159fea0>] ? rest_init+0x80/0x80
[<ffffffff8159feae>] kernel_init+0xe/0x180
[<ffffffff815cca2c>] ret_from_fork+0x7c/0xb0
[<ffffffff8159fea0>] ? rest_init+0x80/0x80
Mem-Info:
Node 0 DMA per-cpu:
CPU 0: hi: 0, btch: 1 usd: 0
Node 0 DMA32 per-cpu:
CPU 0: hi: 42, btch: 7 usd: 0
active_anon:0 inactive_anon:0 isolated_anon:0
active_file:0 inactive_file:0 isolated_file:0
unevictable:0 dirty:0 writeback:0 unstable:0
free:872 slab_reclaimable:13 slab_unreclaimable:1880
mapped:0 shmem:0 pagetables:0 bounce:0
free_cma:0
because the system has run out of memory at boot time. This occurs
because of the following sequence in the boot:
Main kernel boots and sets E820 map. The second kernel is booted with a
map generated by the kdump service using memmap= and memmap=exactmap.
These parameters are added to the kernel parameters of the kexec/kdump
kernel. The kexec/kdump kernel has limited memory resources so as not
to severely impact the main kernel.
The system then panics and the kdump/kexec kernel boots (which is a
completely new kernel boot). During this boot ACPI is initialized and the
kernel (as can be seen above) traverses the ACPI namespace and finds an
entry for a memory device to be hotadded.
ie)
[<ffffffff815a1e9f>] __add_pages+0xaf/0x240
[<ffffffff81047359>] arch_add_memory+0x59/0xd0
[<ffffffff815a21d9>] add_memory+0xb9/0x1b0
[<ffffffff81333b9c>] acpi_memory_device_add+0x18d/0x26d
[<ffffffff81309a01>] acpi_bus_device_attach+0x7d/0xcd
[<ffffffff8132379d>] acpi_ns_walk_namespace+0xc8/0x17f
[<ffffffff81309984>] ? acpi_bus_type_and_status+0x90/0x90
[<ffffffff81309984>] ? acpi_bus_type_and_status+0x90/0x90
[<ffffffff81323c8c>] acpi_walk_namespace+0x95/0xc5
[<ffffffff8130a6d6>] acpi_bus_scan+0x8b/0x9d
[<ffffffff81a2019a>] acpi_scan_init+0x63/0x160
[<ffffffff81a1ffb5>] acpi_init+0x25d/0x2a6
At this point the kernel adds page table information and the the kexec/kdump
kernel runs out of memory.
This can also be reproduced by using the memmap=exactmap and mem=X
parameters on the main kernel and booting.
This patchset resolves the problem by adding a kernel parameter,
acpi_no_memhotplug, to disable ACPI memory hotplug.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Toshi Kani <toshi.kani@hp.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Introduce functions to enable and disable bridgeport address
notification feature, sysfs attributes for access to these
functions from userspace, and udev events emitted when a host
joins or exits a bridgeport-enabled HiperSocket channel.
Signed-off-by: Eugene Crosser <eugene.crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce functions to assign roles and check state of bridgeport-capable
HiperSocket devices, and sysfs attributes providing access to these
functions from userspace. Introduce udev events emitted when the state
of a bridgeport device changes.
Signed-off-by: Eugene Crosser <eugene.crosser@ru.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add disable_cpu_apicid kernel parameter. To use this kernel parameter,
specify an initial APIC ID of the corresponding CPU you want to
disable.
This is mostly used for the kdump 2nd kernel to disable BSP to wake up
multiple CPUs without causing system reset or hang due to sending INIT
from AP to BSP.
Kdump users first figure out initial APIC ID of the BSP, CPU0 in the
1st kernel, for example from /proc/cpuinfo and then set up this kernel
parameter for the 2nd kernel using the obtained APIC ID.
However, doing this procedure at each boot time manually is awkward,
which should be automatically done by user-land service scripts, for
example, kexec-tools on fedora/RHEL distributions.
This design is more flexible than disabling BSP in kernel boot time
automatically in that in kernel boot time we have no choice but
referring to ACPI/MP table to obtain initial APIC ID for BSP, meaning
that the method is not applicable to the systems without such BIOS
tables.
One assumption behind this design is that users get initial APIC ID of
the BSP in still healthy state and so BSP is uniquely kept in
CPU0. Thus, through the kernel parameter, only one initial APIC ID can
be specified.
In a comparison with disabled_cpu_apicid, we use read_apic_id(), not
boot_cpu_physical_apicid, because on some platforms, the variable is
modified to the apicid reported as BSP through MP table and this
function is executed with the temporarily modified
boot_cpu_physical_apicid. As a result, disabled_cpu_apicid kernel
parameter doesn't work well for apicids of APs.
Fixing the wrong handling of boot_cpu_physical_apicid requires some
reviews and tests beyond some platforms and it could take some
time. The fix here is a kind of workaround to focus on the main topic
of this patch.
Signed-off-by: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/20140115064458.1545.38775.stgit@localhost6.localdomain6
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
I had been trying to learn a bit more about the pinctrl subsystem, and I
realized several typos and grammar issues while going through the documentation.
I have probably not caught all the possible issues, but this change is
addressing several places for improvement.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sata_mv driver supports the SATA IP found in several Marvell SoCs.
As some new SATA registers have been introduced with the Armada 370/XP
SoCs, a way to identify them is needed.
This patch introduces a new compatible string for the SATA IP found in
Armada 370/XP SoCs.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
Remove extra comma in pinctrl-single documentation.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes to select missing configuration options, and update of the maintainer
file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=TOqs
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.14-2' of https://github.com/mripard/linux into next/soc
From Maxime Ripard:
Second round of core additions for the Allwinner SoCs
Fixes to select missing configuration options, and update of the maintainer
file.
* tag 'sunxi-core-for-3.14-2' of https://github.com/mripard/linux:
ARM: sunxi: select ARM_PSCI
MAINTAINERS: Update Allwinner sunXi maintainer files
ARM: sunxi: Select RESET_CONTROLLER
ARM: sun6i: Add SMP support for the Allwinner A31
dt-bindings: fix example of allwinner interrupt controller
ARM: sunxi: Register the A31 reset IP in init_time
ARM: sunxi: Select ARCH_HAS_RESET_CONTROLLER
reset: Add Allwinner SoCs Reset Controller Driver
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Use the simple-bus node to discover the io area, and remap the cached and
bypass io ranges. The parent-bus-address value of the first triplet in the
"ranges" property is used. This value is rounded down to the nearest 256MB
boundary. The length of the io area is fixed at 256MB; the "ranges" property
length value is ignored.
Other limitations: (1) only the first simple-bus node is considered, and (2)
only the first triplet of the "ranges" property is considered.
See ePAPR 1.1 §6.5 for the simple-bus node description, and §2.3.8 for the
"ranges" property description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Make the WT entry match table 4-52 of the Xtensa ISA RM (RD-2012.5).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=tliU
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu into next/fixes-non-critical
From Jason Cooper:
mvebu late fixes for v3.13
- mvebu
- fix boot hang on Armada XP due to broken i2c offloading in A0 SoC revision
(specifically experienced on some early OpenBlocks AX3-4 boards)
* tag 'mvebu-fixes-3.13' of git://git.infradead.org/linux-mvebu:
i2c: mv64xxx: Document the newly introduced Armada XP A0 compatible
i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
ARM: mvebu: Add support to get the ID and the revision of a SoC
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Pull clocksource/clockevent updates from Daniel Lezcano:
* Axel Lin removed an unused structure defining the ids for the
bcm kona driver.
* Ezequiel Garcia enabled the timer divider only when the 25MHz
timer is not used for the armada 370 XP.
* Jingoo Han removed a pointless platform data initialization for
the sh_mtu and sh_mtu2.
* Laurent Pinchart added the clk_prepare/clk_unprepare for sh_cmt.
* Linus Walleij added a useful warning in clk_of when no clocks
are found while the old behavior was to silently hang at boot time.
* Maxime Ripard added the high speed timer drivers for the
Allwinner SoCs (A10, A13, A20). He increased the rating, shared the
irq across all available cpus and fixed the clockevent's irq
initialization for the sun4i.
* Michael Opdenacker removed the usage of the IRQF_DISABLED for the
all the timers driver located in drivers/clocksource.
* Stephen Boyd switched to sched_clock_register for the
arm_global_timer, cadence_ttc, sun4i and orion timers.
Conflicts:
drivers/clocksource/clksrc-of.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Conflicts:
net/xfrm/xfrm_policy.c
Steffen Klassert says:
====================
This pull request has a merge conflict between commits be7928d20b
("net: xfrm: xfrm_policy: fix inline not at beginning of declaration") and
da7c224b1b ("net: xfrm: xfrm_policy: silence compiler warning") from
the net-next tree and commit 2f3ea9a95c ("xfrm: checkpatch erros with
inline keyword position") from the ipsec-next tree.
The version from net-next can be used, like it is done in linux-next.
1) Checkpatch cleanups, from Weilong Chen.
2) Fix lockdep complaints when pktgen is used with IPsec,
from Fan Du.
3) Update pktgen to allow any combination of IPsec transport/tunnel mode
and AH/ESP/IPcomp type, from Fan Du.
4) Make pktgen_dst_metrics static, Fengguang Wu.
5) Compile fix for pktgen when CONFIG_XFRM is not set,
from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- drop dependency against CRC16
- move to new release version
- add size check at compile time for packet structs
- update copyright years in every file
- implement new bonding/interface alternation feature
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BKos
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- drop dependency against CRC16
- move to new release version
- add size check at compile time for packet structs
- update copyright years in every file
- implement new bonding/interface alternation feature
Signed-off-by: David S. Miller <davem@davemloft.net>
The default audit_backlog_limit is 64. This was a reasonable limit at one time.
systemd causes so much audit queue activity on startup that auditd doesn't
start before the backlog queue has already overflowed by more than a factor of
2. On a system with audit= not set on the kernel command line, this isn't an
issue since that history isn't kept for auditd when it is available. On a
system with audit=1 set on the kernel command line, kaudit tries to keep that
history until auditd is able to drain the queue.
This default can be changed by the "-b" option in audit.rules once the system
has booted, but won't help with lost messages on boot.
One way to solve this would be to increase the default backlog queue size to
avoid losing any messages before auditd is able to consume them. This would
be overkill to the embedded community and insufficient for some servers.
Another way to solve it might be to add a kconfig option to set the default
based on the system type. An embedded system would get the current (or
smaller) default, while Workstations might get more than now and servers might
get more.
None of these solutions helps if a system's compiled default is too small to
see the lost messages without compiling a new kernel.
This patch adds a kernel set-up parameter (audit already has one to
enable/disable it) "audit_backlog_limit=<n>" that overrides the default to
allow the system administrator to set the backlog limit.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Add the "audit=" kernel start-up parameter to Documentation/kernel-parameters.txt.
Signed-off-by: Richard Guy Briggs <rgb@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
The first variants of Armada XP SoCs (A0 stepping) have issues related
to the i2c controller which prevent to use the offload mechanism and
lead to a kernel hang during boot.
The commit introduces a new the compatible string
marvell,mv78230-a0-i2c for the i2c controller.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
cc: devicetree@vger.kernel.org
Cc: stable@vger.kernel.org # v3.12+: af8d1c63af: ARM: mvebu: Add support to get the ID and the revision of a SoC
Cc: stable@vger.kernel.org # v3.12+: 85e618a1be: ARM: mvebu: Add quirk for i2c for the OpenBlocks AX3-4 board
Cc: stable@vger.kernel.org # v3.12+: 6cf70ae928: i2c: mv64xxx: Fix bus hang on A0 version of the Armada XP SoCs
Cc: stable@vger.kernel.org # v3.12+
Fixes: 930ab3d403 (i2c: mv64xxx: Add I2C Transaction Generator support)
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Now that the DWC2 driver has been moved to drivers/usb, move its
bindings doc to the correct place
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document how to use one AF_PACKET mmap socket for RX and TX.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new ip_no_pmtu_disc mode only allowes fragmentation-needed errors
to be honored by protocols which do more stringent validation on the
ICMP's packet payload. This knob is useful for people who e.g. want to
run an unmodified DNS server in a namespace where they need to use pmtu
for TCP connections (as they are used for zone transfers or fallback
for requests) but don't want to use possibly spoofed UDP pmtu information.
Currently the whitelisted protocols are TCP, SCTP and DCCP as they check
if the returned packet is in the window or if the association is valid.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Suggested-by: Florian Weimer <fweimer@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While forwarding we should not use the protocol path mtu to calculate
the mtu for a forwarded packet but instead use the interface mtu.
We mark forwarded skbs in ip_forward with IPSKB_FORWARDED, which was
introduced for multicast forwarding. But as it does not conflict with
our usage in unicast code path it is perfect for reuse.
I moved the functions ip_sk_accept_pmtu, ip_sk_use_pmtu and ip_skb_dst_mtu
along with the new ip_dst_mtu_maybe_forward to net/ip.h to fix circular
dependencies because of IPSKB_FORWARDED.
Because someone might have written a software which does probe
destinations manually and expects the kernel to honour those path mtus
I introduced a new per-namespace "ip_forward_use_pmtu" knob so someone
can disable this new behaviour. We also still use mtus which are locked on a
route for forwarding.
The reason for this change is, that path mtus information can be injected
into the kernel via e.g. icmp_err protocol handler without verification
of local sockets. As such, this could cause the IPv4 forwarding path to
wrongfully emit fragmentation needed notifications or start to fragment
packets along a path.
Tunnel and ipsec output paths clear IPCB again, thus IPSKB_FORWARDED
won't be set and further fragmentation logic will use the path mtu to
determine the fragmentation size. They also recheck packet size with
help of path mtu discovery and report appropriate errors.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Cc: John Heffner <johnwheffner@gmail.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for Arasan's SDHCI controller core.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Rob Herring <rob.herring@calxeda.com> [binding]
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Chris Ball <chris@printf.net>
Add v4l2 controls to set desired profile for VP8 encoder.
Acceptable levels for VP8 encoder are
0: Version 0
1: Version 1
2: Version 2
3: Version 3
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Pawel Osciak <posciak@chromium.org>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Adds v4l2 controls to set MIN, MAX QP values and
I, P frame QP for vp8 encoder.
Signed-off-by: Kiran AVND <avnd.kiran@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add tlv320aic32x4 to the compatible list in the binding documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJS0miqAAoJEHm+PkMAQRiGbfgIAJSWEfo8ludknhPcHJabBtxu
75SQAKJlL3sBVnxEc58Rtt8gsKYQIrm4IY5Slunklsn04RxuDUIQMgFoAYR5gQwz
+Myqkw/HOqDe5VStGxtLYpWnfglxVwGDCd7ISfL9AOVy5adMWBxh4Tv+qqQc7aIZ
eF7dy+DD+C6Q3Z5OoV8s0FZDxse29vOf17Nki7+7t8WMqyegYwjoOqNeqocGKsPi
eHLrJgTl4T6jB4l9LKKC154DSKjKOTSwZMWgwK8mToyNLT/ufCiKgXloIjEvZZcY
VVKUtncdHiTf+iqVojgpGBzOEeB5DM83iiapFeDiJg8C9yBzvT8lBtA9aPb5Wgw=
=lEeV
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc8' into core/locking
Refresh the tree with the latest fixes, before applying new changes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This makes it possible to debug kernel over FireWire without the need to
recompile it.
[Stefan R: changed description from "...0" to "...N"]
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The old firewire stack is long dead now and a new version firescope has
been released with support for current kernels.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Rob Landley <rob@landley.net>
Cc: Justin P. Mattock <justinmattock@gmail.com>
Cc: Bernhard Kaindl <bk@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add missing sysfs attributes in the proper section of the README
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The LOCK and UNLOCK barriers as described in our barrier document are
generally known as ACQUIRE and RELEASE barriers in other literature.
Since we plan to introduce the acquire and release nomenclature in
generic kernel primitives we should amend the document to avoid
confusion as to what an acquire/release means.
Reviewed-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Victor Kaplansky <VICTORK@il.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Link: http://lkml.kernel.org/r/20131217092435.GC21999@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Often, usb drivers need some driver_info to get a device to work. To
have access to driver_info when using new_id, allow to pass a reference
vendor:product tuple from which new_id will inherit driver_info.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve cache_status to emit:
<metadata block size> <#used metadata blocks>/<#total metadata blocks>
<cache block size> <#used cache blocks>/<#total cache blocks>
...
Adding the block sizes allows for easier calculation of the overall size
of both the metadata and cache devices. Adding <#total cache blocks>
provides useful context for how much of the cache is used.
Unfortunately these additions to the status will require updates to
users' scripts that monitor the cache status. But these changes help
provide more comprehensive information about the cache device and will
simplify tools that are being developed to manage dm-cache devices --
because they won't need to issue 3 operations to cobble together the
information that we can easily provide via a single status ioctl.
While updating the status documentation in cache.txt spaces were
tabify'd.
Requested-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
Changed from "Please not that" to "Please note that"
Signed-off-by: David E. Narvaez <david.narvaez@computer.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch implements a device-tree-only CPU DAI driver for Freescale ESAI
controller that supports:
- 12 channels playback and 8 channels record.
[ Some of the inner transmitters and receivers are sharing same group of
pins. So the maxmium 12 output or 8 input channels are only valid if
there is no pin conflict occurring to it. ]
- Independent (asynchronous mode) or shared (synchronous mode) transmit and
receive sections with separate or shared internal/external clocks and frame
syncs, operating in Master or Slave mode.
[ Current ALSA seems not to allow CPU DAI drivers to configure DAI format
separately for PLAYBACK and CAPTURE. So this first version only supports
the case that uses the same DAI format for both directions. ]
- Various DAI formats: I2S, Left-Justified, Right-Justified, DSP-A and DSP-B.
- Programmable word length (8, 16, 20 or 24bits)
- Flexible selection between system clock or external oscillator as input
clock source, programmable internal clock divider and frame sync generation.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Documentation/i2c/fault-codes illustrates EINVAL error code
as follows:
"One example would be a driver trying an SMBus Block Write
with block size outside the range of 1-32 bytes."
However, the actual implementation of i2c subsystem truncates
data length to be 32 bytes.
Hence this example cannot happen anymore, and since it's obsolete,
let's simply remove it from Documentation/i2c/fault-codes.
Signed-off-by: Helia Correia <helia.correia@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is no list of compatibles that are supported. This patch adds a
list of compatibles to the documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds missing some description of sysfs entries in
- Documentation/ABI/testing/sysfs-fs-f2fs
- Documentation/filesystems/f2fs.txt.
And it adds a maintained document entry of F2FS in MAINTAINERS.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patchset add new driver of extcon-max14577.c which detect various external
connector and fix minor issue of extcon provider driver(extcon-arizona/palams/
gpio.c). Also, update documentation of previous 'switch' porting guide and
extcon git repository url.
Detailed description for patchset:
- New driver of extcon-max14577.c
: Add extcon-max14577.c drvier to support Maxim MUIC(Micro USB Interface
Controller) which detect USB/TA/JIG/AUDIO-DOCK and additional accessory
according to each resistance when connected external connector.
- extcon-arizoan.c driver
: Code clean to use define macro instead of hex value
: Fix minor issue to reset back to our staring state
: Fix race with microphone detection and removal
- extcon-palmas.c driver
: Fix minor issue and renaming compatible string of Devicetree
- extcon-gpio.c driver
: Fix bug about ordering initialization of gpio pin on probe()
: Send uevent after wakeup from suspend state because some SoC
haven't wakeup interrupt on suspend state.
- Documentation (Documentation/extcon/porting-android-switch-class)
: Fix switch class porting guide
- Update extcon git repository url
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eIUL
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next
Chanwoo writes:
Update extcon for v3.14
This patchset add new driver of extcon-max14577.c which detect various external
connector and fix minor issue of extcon provider driver(extcon-arizona/palams/
gpio.c). Also, update documentation of previous 'switch' porting guide and
extcon git repository url.
Detailed description for patchset:
- New driver of extcon-max14577.c
: Add extcon-max14577.c drvier to support Maxim MUIC(Micro USB Interface
Controller) which detect USB/TA/JIG/AUDIO-DOCK and additional accessory
according to each resistance when connected external connector.
- extcon-arizoan.c driver
: Code clean to use define macro instead of hex value
: Fix minor issue to reset back to our staring state
: Fix race with microphone detection and removal
- extcon-palmas.c driver
: Fix minor issue and renaming compatible string of Devicetree
- extcon-gpio.c driver
: Fix bug about ordering initialization of gpio pin on probe()
: Send uevent after wakeup from suspend state because some SoC
haven't wakeup interrupt on suspend state.
- Documentation (Documentation/extcon/porting-android-switch-class)
: Fix switch class porting guide
- Update extcon git repository url
The update did not applied on Korean translation although it applied on
English documentation. Apply it on Korean translation now.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
English version HOWTO updated the versioning but Korean version didn't.
Update it now.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
English version HOWTO updated the address but Korean version didn't.
Update it now.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
English version HOWTO updated the link but Korean version didn't. Update
it now.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Building mei-amt-version.o triggers a GCC warning:
Documentation/misc-devices/mei/mei-amt-version.c: In function 'main':
Documentation/misc-devices/mei/mei-amt-version.c:103:5: warning: 'acmd.fd' is used uninitialized in this function [-Wuninitialized]
if (cl->fd != -1)
^
Documentation/misc-devices/mei/mei-amt-version.c:443:21: note: 'acmd.fd' was declared here
struct amt_host_if acmd;
^
GCC is correct. See, the call chain that GCC detects must be
main()
amt_host_if_init()
mei_init()
mei_deinit()
But when we enter mei_deinit() struct amt_host_if acmd is still
unitialized. That makes the test for (effectively) amt_host_if->mei_cl->fd
bogus.
But it turns out that call of mei_deinit() isn't needed at all. All of
the members of mei_cl will be set later in mei_init() and none will be
used before they are set. So we can simply drop this call of
mei_deinit().
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Tomas Winkler <tomas.winkler@intel.com>
Reported-by: David Howells <dhowells@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attribute can be used to set and read the value and the
mask of the skb mark which will be used to classify the
source non-mesh client as ISOLATED. In this way a client can
be advertised as such and the mark can potentially be
restored at the receiving node before delivering the skb.
This can be helpful for creating network wide netfilter
policies.
This sysfs file expects a string of the shape "$mark/$mask".
Where $mark has to be a 32-bit number in any base, while
$mask must be a 32bit mask expressed in hex base. Only bits
in $mark covered by the bitmask are really stored.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
If max77686 chip is instantiated from device tree, it is desirable to
have an OF clock provider to allow device tree based look-up of clocks.
This patch adds OF clock provider registration to the clk-max77686
driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
SoC family definitions at the moment are reactive to board needs.
This results in potentially wrong matches taking place for board types.
Eventually, we will have descriptors match only with SoC types and
should not contain anything specific to board handling and pave the
way to getting rid of soc_is_XYZ checks and allow this determination
done with matches at of level.
Existing implicit definitions(as part of board descriptions) are
explicitly documented.
NOTE: Even though we prefer to have dt compatibility to explicit,
"ti,dra7xx", "ti,am33xx", "ti,omap36xx" preexist in current dts and
are maintained for backward compatibility. It is also expected that
any future SoC addition will keep this documentation updated.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AudioSS block on Exynos 5420 has an additional clock gate for the
ADMA bus clock.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
There is no gate for the PCM clock input to the AudioSS block, so
the parent of sclk_pcm is div_pcm0. Add a clock ID for it so that
we can reference it in device trees.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
This allows the input clocks to the Exynos AudioSS block to be
specified via device-tree bindings. Default names will be used
when an input clock is not given.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
The Chunghwa CLAA101WA01A is a 10.1" 1366x768 panel, which can be
supported by the simple panel driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Samsung LNT101NT05 10.1" WXVGA panel can be supported by the simple panel
driver.
Cc: linux-fbdev@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Update the documentation also to reflect the fact that there are no ACPI
specific GPIO interfaces anymore but drivers should instead use the
descriptor based GPIO APIs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
TWR-P1025 Overview
-----------------
512Mbyte DDR3 (on board DDR)
64MB Nor Flash
eTSEC1: Connected to RGMII PHY AR8035
eTSEC3: Connected to RGMII PHY AR8035
Two USB2.0 Type A
One microSD Card slot
One mini-PCIe slot
One mini-USB TypeB dual UART
Signed-off-by: Michael Johnston <michael.johnston@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
[scottwood@freescale.com: use pr_info rather than KERN_INFO]
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch replace custom handling of IrDA feature with N_IRDA
line discipline, so IrDA mode can be used with irtty driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have already renamed the file name, change doc name at this
patch.
Cc: devicetree@vger.kernel.org
Cc: linux-doc@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PCI-DMA-mapping.txt moved to general docs and became DMA-API-HOWTO.txt
in 5e07c2c730 ("Documentation: rename PCI/PCI-DMA-mapping.txt to
DMA-API-HOWTO.txt"). Add new file about PCI Express I/O Virtualization.
Signed-off-by: Erik Ekman <erik@kryo.se>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This change allows to follow a recommandation of RFC4942.
- Add "anycast_src_echo_reply" sysctl to control the use of anycast addresses
as source addresses for ICMPv6 echo reply. This sysctl is false by default
to preserve existing behavior.
- Add inline check ipv6_anycast_destination().
- Use them in icmpv6_echo_reply().
Reference:
RFC4942 - IPv6 Transition/Coexistence Security Considerations
(http://tools.ietf.org/html/rfc4942#section-2.1.6)
2.1.6. Anycast Traffic Identification and Security
[...]
To avoid exposing knowledge about the internal structure of the
network, it is recommended that anycast servers now take advantage of
the ability to return responses with the anycast address as the
source address if possible.
Signed-off-by: Francois-Xavier Le Bail <fx.lebail@yahoo.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
hardware.h inclusion is no longer needed. Update the documentation section
related to it and fix a file path.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the ASoC overview to bring it up to date with the current code base
and include multi-component.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
LDO indices start from 1. Update the example accordingly.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for DMA controller of BCM2835 as used in the Raspberry Pi.
Currently it only supports cyclic DMA.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Even though we might not have rigor rule for the simple card property names,
according to the existing ones, they are all in a same pattern:
[simple-audio-card,]XXX;
Rename simple-audio-routing to simple-audio-card,routing, and make the simple
card's properties has one unified name.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Internally the mq policy maintains a promotion threshold variable. If
the hit count of a block not in the cache goes above this threshold it
gets promoted to the cache.
This patch introduces three new tunables that allow you to tweak the
promotion threshold by adding a small value. These adjustments depend
on the io type:
read_promote_adjustment: READ io, default 4
write_promote_adjustment: WRITE io, default 8
discard_promote_adjustment: READ/WRITE io to a discarded block, default 1
If you're trying to quickly warm a new cache device you may wish to
reduce these to encourage promotion. Remember to switch them back to
their defaults after the cache fills though.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
If the pool runs out of data or metadata space, the pool can either
queue or error the IO destined to the data device. The default is to
queue the IO until more space is added.
An admin may now configure the pool to error IO when no space is
available by setting the 'error_if_no_space' feature when loading the
thin-pool table.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
As discussed on the media summit 2013, there is no reason for the width
and height to be signed.
Therefore this patch is an attempt to convert those fields from __s32 to
__u32.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi> (documentation and smiapp)
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are already video output drivers that allow STREAMON without
any buffers queued, and with the change in vb2 there are now more
drivers like that.
So saying "The ioctl will succeed only when at least one output
buffer is in the incoming queue." isn't true. Just drop the word
'only'. We cannot say that it will also work if no output buffers are
queued as long as not all drivers are converted to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Change "packet" to "packed" where the doc is talking about packed data
formats.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The xref to the v4l2-mbus-pixelcode-yuv8 table gets rendered as "Table
4.22, “YUV Formats”", so use the verb in the third person singular
because it refers to "Table":
s/list/lists/
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The Palmas device contains only a USB VBUS-ID detector, so added a
compatible type *ti,palmas-usb-vid*. Didn't remove the existing compatible
types for backward compatibility.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a Documentation/ABI entry for
/sys/devices/system/cpu/intel_pstate/max_perf_pct,
/sys/devices/system/cpu/intel_pstate/min_perf_pct, and
/sys/devices/system/cpu/intel_pstate/no_turbo.
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=0B0x
-----END PGP SIGNATURE-----
Merge tag 'samsung-clk-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tfiga/samsung-clk into clk-fixes
Samsung Clock fixes for 3.13-rc7
* Several patches fixing up incorrectly defined register addresses and
bitfield offsets that could lead to undefined operation when accessing
respective registers or bitfields.
1) clk: exynos5250: fix sysmmu_mfc{l,r} gate clocks
2a) clk: samsung: exynos5250: Fix ACP gate register offset
2b) clk: samsung: exynos5250: Add MDMA0 clocks
2c) ARM: dts: exynos5250: Fix MDMA0 clock number
3) clk: samsung: exynos4: Correct SRC_MFC register
All three issues have been present since Exynos5250 and Exynos4 clock
drivers were added by commits 6e3ad26816 ("clk: exynos5250:
register clocks using common clock framework") and e062b57177
("clk: exynos4: register clocks using common clock framework")
respectively.
* Patch to fix automatic disabling of Exynos5250 sysreg clock that could
cause undefined operation of several peripherals, such as USB, I2C,
MIPI or display block.
4) clk: samsung: exynos5250: Add CLK_IGNORE_UNUSED flag for the sysreg
clock
Present since Exynos5250 clock drivers was added by commits
6e3ad26816 ("clk: exynos5250: register clocks using common clock
framework").
* Patch fixing compilation warning in clk-exynos-audss driver when
CONFIG_PM_SLEEP is disabled.
5) clk: exynos: File scope reg_save array should depend on PM_SLEEP
Present since the driver was added by commit 1241ef94cc ("clk:
samsung: register audio subsystem clocks using common clock
framework").
Pablo Neira Ayuso says:
====================
netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next tree,
they are:
* Add full port randomization support. Some crazy researchers found a way
to reconstruct the secure ephemeral ports that are allocated in random mode
by sending off-path bursts of UDP packets to overrun the socket buffer of
the DNS resolver to trigger retransmissions, then if the timing for the
DNS resolution done by a client is larger than usual, then they conclude
that the port that received the burst of UDP packets is the one that was
opened. It seems a bit aggressive method to me but it seems to work for
them. As a result, Daniel Borkmann and Hannes Frederic Sowa came up with a
new NAT mode to fully randomize ports using prandom.
* Add a new classifier to x_tables based on the socket net_cls set via
cgroups. These includes two patches to prepare the field as requested by
Zefan Li. Also from Daniel Borkmann.
* Use prandom instead of get_random_bytes in several locations of the
netfilter code, from Florian Westphal.
* Allow to use the CTA_MARK_MASK in ctnetlink when mangling the conntrack
mark, also from Florian Westphal.
* Fix compilation warning due to unused variable in IPVS, from Geert
Uytterhoeven.
* Add support for UID/GID via nfnetlink_queue, from Valentina Giusti.
* Add IPComp extension to x_tables, from Fan Du.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel P-state driver is currently undocumented. Add some
documentation based on the cover-letter sent with the original series.
Cc: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Ramkumar Ramachandra <artagnon@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for the MXS DCP block. The driver currently supports
SHA-1/SHA-256 hashing and AES-128 CBC/ECB modes. The non-standard
CRC32 is not yet supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Document the clock properties required by the at91 i2c bus driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add device tree support for twl4030 keypad driver.
Tested on Nokia N900.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cCZc
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
From Linus Walleij:
Some Integrator patches that matured for v3.14:
- Use PATCH_PHYS_TO_VIRT and AUTO_ZRELADDR.
- Support cascaded interrupts on the SIC.
- Complete clock implementation for the IM-PD1.
* tag 'integrator-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
clk: versatile: fixup IM-PD1 clock implementation
clk: versatile: pass a name to ICST clock provider
ARM: integrator: pass parent IRQ to the SIC
irqchip: versatile FPGA: support cascaded interrupts from DT
ARM: integrator: Default enable ARM_PATCH_PHYS_VIRT, AUTO_ZRELADDR
Signed-off-by: Olof Johansson <olof@lixom.net>
This mostly adds the reset controller initialisation for the A31 and the SMP
operations for this SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zEQv
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-3.14' of https://github.com/mripard/linux into next/drivers
From Maxime Ripard:
Allwinner core changes for 3.14
This mostly adds the reset controller initialisation for the A31 and the SMP
operations for this SoC.
* tag 'sunxi-core-for-3.14' of https://github.com/mripard/linux:
ARM: sun6i: Add SMP support for the Allwinner A31
dt-bindings: fix example of allwinner interrupt controller
ARM: sunxi: Register the A31 reset IP in init_time
ARM: sunxi: Select ARCH_HAS_RESET_CONTROLLER
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds pci_enable_msi_range(), which supersedes the pci_enable_msi()
and pci_enable_msi_block() MSI interfaces.
It also adds pci_enable_msix_range(), which supersedes the
pci_enable_msix() MSI-X interface.
The old interfaces have three categories of return values:
negative: failure; caller should not retry
positive: failure; value indicates number of interrupts that *could*
have been allocated, and caller may retry with a smaller request
zero: success; at least as many interrupts allocated as requested
It is error-prone to handle these three cases correctly in drivers.
The new functions return either a negative error code or a number of
successfully allocated MSI/MSI-X interrupts, which is expected to lead to
clearer device driver code.
pci_enable_msi(), pci_enable_msi_block() and pci_enable_msix() still exist
unchanged, but are deprecated and may be removed after callers are updated.
[bhelgaas: tweak changelog]
Suggested-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
This creates an MSI-X counterpart for pci_msi_vec_count(). Device drivers
can use this function to obtain maximum number of MSI-X interrupts the
device supports and use that number in a subsequent call to
pci_enable_msix().
pci_msix_vec_count() supersedes pci_msix_table_size() and returns a
negative errno if device does not support MSI-X interrupts. After this
update, callers must always check the returned value.
The only user of pci_msix_table_size() was the PCI-Express port driver,
which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Device drivers can use this interface to obtain the maximum number of MSI
interrupts the device supports and use that number, e.g., in a subsequent
call to pci_enable_msi_block().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
It would be useful e.g. in a server or desktop environment to have
a facility in the notion of fine-grained "per application" or "per
application group" firewall policies. Probably, users in the mobile,
embedded area (e.g. Android based) with different security policy
requirements for application groups could have great benefit from
that as well. For example, with a little bit of configuration effort,
an admin could whitelist well-known applications, and thus block
otherwise unwanted "hard-to-track" applications like [1] from a
user's machine. Blocking is just one example, but it is not limited
to that, meaning we can have much different scenarios/policies that
netfilter allows us than just blocking, e.g. fine grained settings
where applications are allowed to connect/send traffic to, application
traffic marking/conntracking, application-specific packet mangling,
and so on.
Implementation of PID-based matching would not be appropriate
as they frequently change, and child tracking would make that
even more complex and ugly. Cgroups would be a perfect candidate
for accomplishing that as they associate a set of tasks with a
set of parameters for one or more subsystems, in our case the
netfilter subsystem, which, of course, can be combined with other
cgroup subsystems into something more complex if needed.
As mentioned, to overcome this constraint, such processes could
be placed into one or multiple cgroups where different fine-grained
rules can be defined depending on the application scenario, while
e.g. everything else that is not part of that could be dropped (or
vice versa), thus making life harder for unwanted processes to
communicate to the outside world. So, we make use of cgroups here
to track jobs and limit their resources in terms of iptables
policies; in other words, limiting, tracking, etc what they are
allowed to communicate.
In our case we're working on outgoing traffic based on which local
socket that originated from. Also, one doesn't even need to have
an a-prio knowledge of the application internals regarding their
particular use of ports or protocols. Matching is *extremly*
lightweight as we just test for the sk_classid marker of sockets,
originating from net_cls. net_cls and netfilter do not contradict
each other; in fact, each construct can live as standalone or they
can be used in combination with each other, which is perfectly fine,
plus it serves Tejun's requirement to not introduce a new cgroups
subsystem. Through this, we result in a very minimal and efficient
module, and don't add anything except netfilter code.
One possible, minimal usage example (many other iptables options
can be applied obviously):
1) Configuring cgroups if not already done, e.g.:
mkdir /sys/fs/cgroup/net_cls
mount -t cgroup -o net_cls net_cls /sys/fs/cgroup/net_cls
mkdir /sys/fs/cgroup/net_cls/0
echo 1 > /sys/fs/cgroup/net_cls/0/net_cls.classid
(resp. a real flow handle id for tc)
2) Configuring netfilter (iptables-nftables), e.g.:
iptables -A OUTPUT -m cgroup ! --cgroup 1 -j DROP
3) Running applications, e.g.:
ping 208.67.222.222 <pid:1799>
echo 1799 > /sys/fs/cgroup/net_cls/0/tasks
64 bytes from 208.67.222.222: icmp_seq=44 ttl=49 time=11.9 ms
[...]
ping 208.67.220.220 <pid:1804>
ping: sendmsg: Operation not permitted
[...]
echo 1804 > /sys/fs/cgroup/net_cls/0/tasks
64 bytes from 208.67.220.220: icmp_seq=89 ttl=56 time=19.0 ms
[...]
Of course, real-world deployments would make use of cgroups user
space toolsuite, or own custom policy daemons dynamically moving
applications from/to various cgroups.
[1] http://www.blackhat.com/presentations/bh-europe-06/bh-eu-06-biondi/bh-eu-06-biondi-up.pdf
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: cgroups@vger.kernel.org
Acked-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The Versatile FPGA interrupt controller supports cascading interrupts,
i.e. that its output is connected to the input of another interrupt
controller. This makes it possible to pass a parent interrupt from
the device tree and print it in the boot log if applicable.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Keystone arch has compatible nand device, so reuse it.
In case with Keystone it depends on TI_AEMIF because AEMIF
driver is responsible to set timings.
See http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
The properties davinci-ecc-mode, davinci-nand-use-bbt, davinci-nand-buswidth
are MTD generic. Correct names for them are: nand-ecc-mode, nand-on-flash-bbt,
nand-bus-width accordingly. So rename them in dts and documentation.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Extend bindings for davinci_nand driver to be more clear.
This is clarification only, without semantic changes.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Move bindings under mtd. Do this in order to make davinci-nand
driver usable by keystone architecture.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Add support for flash-based bad block table using Marvell's
custom in-flash bad block table layout. The support is enabled
a 'flash_bbt' platform data or device tree parameter.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Given there's no public specification to this date, and in order
to capture some important details and singularities about the
controller let's document them once and for good.
Cc: linux-doc@vger.kernel.org
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Since the driver supports the new compatible string, the binding
documentation must be updated to reflect it.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
In default way, we use the ecc_strength/ecc_step size calculated by ourselves
and use all the OOB area.
This patch adds a new property : "fsl,use-minimum-ecc"
If we enable it, we will firstly try to use the datasheet's minimum required
ECC provided by the MTD layer (the ecc_strength_ds/ecc_step_ds fields
in the nand_chip{}). So we may have free space in the OOB area by using the
minimum ECC, and we may support JFFS2 with some SLC NANDs, such as Micron's
SLC NAND.
If we fail to use the minimum ECC, we will use the legacy method to calculate
the ecc_strength and ecc_step size.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
This patch adds polling mode support for i2c-s3c2410 driver.The
SATA PHY controller's CMU and TRSV block's are of I2C register
map in exynos5250.These blocks can be configured using i2c.
But i2c controller instance on which these block's sits lacks an
interrupt line.Also the current i2c-s3c2410 driver is only interrupt
driven, thus a polling mode support is required in the driver for
supporting this controller. This patch adds this support to the driver.
Signed-off-by: Vasanth Ananthan <vasanth.a@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If a reset GPIO support is specified, request the GPIO and get the chip
out of reset at probe time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Thermal sensor needs pll3_usb_otg when measuring temperature,
otherwise the temperature read will be incorrect, so need to
enable this clk before sensor working, for alarm function,
as hardware will take measurement periodically, so we should
keep this clk always on once alarm function is enabled.
Signed-off-by: Anson Huang <b20788@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Patch "ima: extend the measurement list to include the file signature"
defined a new field called 'sig' and a new template called 'ima-sig'.
This patch updates the Documentation/security/IMA-templates.txt.
Changelog:
- fixed formatting issues (Roberto Sassu)
Reported-by: Roberto Sassu <roberto.sassu@polito.it>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Update pktgen.txt for reference when using IPsec.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Enable to fetch data from a file offset. Currently it only supports
fetching from same binary uprobe set. It'll translate the file offset
to a proper virtual address in the process.
The syntax is "@+OFFSET" as it does similar to normal memory fetching
(@ADDR) which does no address translation.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Enable to fetch other types of argument for the uprobes. IOW, we can
access stack, memory, deref, bitfield and retval from uprobes now.
The format for the argument types are same as kprobes (but @SYMBOL
type is not supported for uprobes), i.e:
@ADDR : Fetch memory at ADDR
$stackN : Fetch Nth entry of stack (N >= 0)
$stack : Fetch stack address
$retval : Fetch return value
+|-offs(FETCHARG) : Fetch memory at FETCHARG +|- offs address
Note that the retval only can be used with uretprobes.
Original-patch-by: Hyeoncheol Lee <cheol.lee@lge.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Hyeoncheol Lee <cheol.lee@lge.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
The uprobe syntax requires an offset after a file path not a symbol.
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: zhangwei(Jovi) <jovi.zhangwei@huawei.com>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSwiPBAAoJEFBXWFqHsHzO3/AIALlP6m/7taIQW5wO4o4aqdwk
GsN7IdsfWH/biG9VyxgpIoJKUqaOJckGA0eyLSeEG7p78xlf0n7cVPUNwzz9z1Vc
zxLSaVNznVOa4fTIsbMK9U+gUP931hjXskxD3tH98MUFqlM0JLQYoofr/lXG7Esf
N2p8B9aUND3WSxDa+d+CsW0B3FBj1piOQDMDgrdc3p7kjcAJs31KaKfUa06o7gzM
a81OaD9Vk0ONf44wh1LGlg0hDRsatQOa4tUTimeV14CnESKqsKxT4qAJ6pZLdfOt
KyRqSk4f4mkpimv4bGdhXTIsIko1CD9wg7G9fsSaolh3OEP0yyNf1savR1fmwCI=
=Hhbl
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
From Shawn Guo:
i.MX SoC changes for 3.14:
- Add the initial i.MX50 SoC support
- Support device tree boot for i.MX35
- Move imx5 clock driver to use macros for clock ID
- Some random updates and non-critical fixes on clock drivers
- A few defconfig updates and minor cleanups
* tag 'imx-soc-3.14' of git://git.linaro.org/people/shawnguo/linux-2.6: (37 commits)
ARM: imx: improve the comment of CCM lpm SW workaround
ARM: imx: improve status check of clock gate
ARM: imx: add necessary interface for pfd
ARM: imx_v6_v7_defconfig: Select CONFIG_REGULATOR_PFUZE100
ARM: imx_v6_v7_defconfig: Select MX35 and MX50 device tree support
ARM: imx: Add cpu frequency scaling support
ARM i.MX35: Add devicetree support.
ARM: imx: update imx_v6_v7_defconfig
ARM: imx6sl: Add missing spba clock to clock tree
ARM: imx6sl: Add missing pll4_audio_div to the clock tree
ARM: imx6: Derive spdif clock from pll3_pfd3_454m
ARM: imx: use __initconst for const init definition
ARM i.MX5: fix obvious typo in ldb_di0_gate clk definition
ARM i.MX5: set CAN peripheral clock to 24 MHz parent
ARM: imx: pllv1: Fix PLL calculation for i.MX27
ARM i.MX5: fix "shift" value for lp_apm_sel on i.MX50 and i.MX53
ARM: imx: imx53: Add SATA PHY clock
ARM: imx_v6_v7_defconfig: Enable STMPE touchscreen
ARM: imx: rename IMX6SL_CLK_CLK_END to IMX6SL_CLK_END
ARM: imx: select PINCTRL at sub-architecure level
...
Signed-off-by: Olof Johansson <olof@lixom.net>
---------------------------
This pull request contains updates
to DaVinci GPIO driver and the
resultant platform code changes. The
updates include DT-conversion and
changes to make the driver cross-platform
ready.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=DxLt
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/drivers
From Sekhar Nori:
DaVinci GPIO driver updates
---------------------------
This pull request contains updates to DaVinci GPIO driver and the
resultant platform code changes. The updates include DT-conversion and
changes to make the driver cross-platform ready.
* tag 'davinci-for-v3.14/gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
gpio: davinci: don't create irq_domain in case of unbanked irqs
gpio: davinci: use chained_irq_enter/chained_irq_exit API
gpio: davinci: add OF support
gpio: davinci: remove unused variable intc_irq_num
gpio: davinci: convert to use irqdomain support.
gpio: introduce GPIO_DAVINCI kconfig option
gpio: davinci: get rid of DAVINCI_N_GPIO
gpio: davinci: use {readl|writel}_relaxed() instead of __raw_*
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJSuYavAAoJENfPZGlqN0++iBQP/iRLdbZzrBtIqfPOAx7kOKC5
14kMul6tggT556xW++JhpUR/s5HdGZoUwq2XhWbzMm9rhE9FFsIOsjSROU9qwItG
4indJRS7p/2/c0vVD988QcgOK9yD++t4hMM42lZ4FsTZL7RT7t5di/Dx2OP8OyU8
LwTLYNRM8icePh+KVtEXyFKjCu22/tuj8FyPJoSruJPsPkd3w8Wt9o7ZLqp58DkG
91EYVWzbKC9JOfXhW/nybDpLpaaNC/MaeIfh2K9HFhAUnhOYDJp1dU7xIz7Wj8/j
PS9RXuNr+Vyj0ov5Y5VqgFwXz1bPFBHsMXvnh7HBwNoaxK6Nvs9ZMREfVLvsAZCS
jiWIYJLozAQX+Xmj7oYBb1kUkEE/WE8ec5GufNp43Eg6mSWsEx/YVFvSfPO/PYvG
3be9jUglpZFmh9i2f2ZtB0AG2q45HieK8i9glufg+wkKnahhOYgynV4dxTvfIEts
qQCZSoAL8KbmrMZpsW0Q9D3SvEFxcuhEtVk8h6X2lg+XcjJ9dwbH8BsBCI8W6Y+m
tOc0yeK8DQhpNastoo1xATQO1MpSTqnSWwP7j6oAS4W44iuJmGLEYLiDCLuamOto
CzGBDCluic3vMMnr3BmJLd/8P+T7IxUZ/0W8aPX786sVBMjsNJPRlyal5sA4/EJl
7Swi8gxCsasfSQLbHsab
=IZCI
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/drivers
From Simon Horman:
Third Round of Renesas SH SCI Updates for v3.14
* Add Device Tree Support
* Remove platform data mapbase and irqs fields
* Remove platform data scbrr_algo_id field
* tag 'renesas-sh-sci3-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
serial: sh-sci: Add OF support
serial: sh-sci: Add device tree bindings documentation
serial: sh-sci: Remove platform data mapbase and irqs fields
serial: sh-sci: Remove platform data scbrr_algo_id field
Signed-off-by: Olof Johansson <olof@lixom.net>
Tested with a r7s72100 genmai board acessing an eeprom.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
cppcheck reports this error:
Documentation/laptops/hpfall.c:33]: (error)
Dangerous usage of 'devname' (strncpy doesn't always 0-terminate it)
The terminating '\0' is needed for the global char array unload_heads_path,
so never write the last array entry (which is initially '\0').
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add Capella Microsystem CM32181 Ambient Light Sensor IIO driver.
This driver will convert raw data to lux value under open-air
condition. Change the calibscale based on the cover material.
Signed-off-by: Kevin Tsai <ktsai@capellamicro.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Modify the existing Kconfig, Makefile, and MAINTAINERS to add the driver
to the kernel. Add a Makefile and a documentation
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently each rbd device is allocated its own major number, which
leads to a hard limit of 230-250 images mapped at once. This commit
adds support for a new single-major device number allocation scheme,
which is hidden behind a new single_major boolean module parameter and
is disabled by default for backwards compatibility reasons. (Old
userspace cannot correctly unmap images mapped under single-major
scheme and would essentially just unmap a random image, if that.)
$ rbd showmapped
id pool image snap device
0 rbd b100 - /dev/rbd0
1 rbd b101 - /dev/rbd1
2 rbd b102 - /dev/rbd2
3 rbd b103 - /dev/rbd3
Old scheme (modprobe rbd):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:24 /dev/rbd0
brw-rw---- 1 root disk 252, 0 Dec 10 12:28 /dev/rbd1
brw-rw---- 1 root disk 252, 1 Dec 10 12:28 /dev/rbd1p1
brw-rw---- 1 root disk 252, 2 Dec 10 12:28 /dev/rbd1p2
brw-rw---- 1 root disk 252, 3 Dec 10 12:28 /dev/rbd1p3
brw-rw---- 1 root disk 251, 0 Dec 10 12:28 /dev/rbd2
brw-rw---- 1 root disk 251, 1 Dec 10 12:28 /dev/rbd2p1
brw-rw---- 1 root disk 250, 0 Dec 10 12:24 /dev/rbd3
New scheme (modprobe rbd single_major=Y):
$ ls -l /dev/rbd*
brw-rw---- 1 root disk 253, 0 Dec 10 12:30 /dev/rbd0
brw-rw---- 1 root disk 253, 256 Dec 10 12:30 /dev/rbd1
brw-rw---- 1 root disk 253, 257 Dec 10 12:30 /dev/rbd1p1
brw-rw---- 1 root disk 253, 258 Dec 10 12:30 /dev/rbd1p2
brw-rw---- 1 root disk 253, 259 Dec 10 12:30 /dev/rbd1p3
brw-rw---- 1 root disk 253, 512 Dec 10 12:30 /dev/rbd2
brw-rw---- 1 root disk 253, 513 Dec 10 12:30 /dev/rbd2p1
brw-rw---- 1 root disk 253, 768 Dec 10 12:30 /dev/rbd3
(major 253 was assigned dynamically at module load time)
The new limit is 4096 images mapped at once, and it comes from the fact
that, as before, 256 minor numbers are reserved for each mapping.
(A follow-up commit changes the number of minors reserved and the way
we deal with partitions over that number.)
If single_major is set to true, two new sysfs interfaces show up:
/sys/bus/rbd/{add,remove}_single_major. These are to be used instead
of /sys/bus/rbd/{add,remove}, which are disabled for backwards
compatibility reasons outlined above.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Introduce /sys/bus/rbd/devices/<id>/minor sysfs attribute for exporting
rbd whole disk minor numbers. This is a step towards single-major
device number allocation scheme, but also a good thing on its own.
Signed-off-by: Ilya Dryomov <ilya.dryomov@inktank.com>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Document the device tree binding for Broadcom Kona architecture
clock control units and clocks. Kona device nodes are represented
with compatible strings having "bcm11351" in their name.
Kona clocks are managed by "clock control units" (CCUs). Each CCU
has a device tree node, and within that node are defined the names
of the clocks provided by the CCU.
The BCM281xx family of SoCs use Kona CCUs and clocks.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJSwLfoAAoJEHm+PkMAQRiGi6QH/1U1B7lmHChDTw3jj1lfm9gA
189Si4QJlnxFWCKHvKEL+pcaVuACU+aMGI8+KyMYK4/JfuWVjjj5fr/SvyHH2/8m
LdSK8aHMhJ46uBS4WJ/l6v46qQa5e2vn8RKSBAyKm/h4vpt+hd6zJdoFrFai4th7
k/TAwOAEHI5uzexUChwLlUBRTvbq4U8QUvDu+DeifC8cT63CGaaJ4qVzjOZrx1an
eP6UXZrKDASZs7RU950i7xnFVDQu4PsjlZi25udsbeiKcZJgPqGgXz5ULf8ZH8RQ
YCi1JOnTJRGGjyIOyLj7pyB01h7XiSM2+eMQ0S7g54F2s7gCJ58c2UwQX45vRWU=
=/4/R
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc6' into for-3.14/core
Needed to bring blk-mq uptodate, since changes have been going in
since for-3.14/core was established.
Fixup merge issues related to the immutable biovec changes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Conflicts:
block/blk-flush.c
fs/btrfs/check-integrity.c
fs/btrfs/extent_io.c
fs/btrfs/scrub.c
fs/logfs/dev_bdev.c
Use clock defines in order to make devicetrees more
human readable.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Adds gate clock for MDMA0 on Exynos5250 SoC. This is needed to ensure
that the clock is enabled when MDMA0 is used on systems on which
firmware gates the clockby default.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
[t.figa: Updated patch description.]
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
kexec-tools use boot_params for getting the 1st kernel hardware_subarch,
the kexec kernel EFI runtime support also needs to read the old efi_info
from boot_params. Currently it exists in debugfs which is not a good
place for such infomation. Per HPA, we should avoid "sploit debugfs".
In this patch /sys/kernel/boot_params are exported, also the setup_data is
exported as a subdirectory. kexec-tools is using debugfs for hardware_subarch
for a long time now so we're not removing it yet.
Structure is like below:
/sys/kernel/boot_params
|__ data /* boot_params in binary*/
|__ setup_data
| |__ 0 /* the first setup_data node */
| | |__ data /* setup_data node 0 in binary*/
| | |__ type /* setup_data type of setup_data node 0, hex string */
[snip]
|__ version /* boot protocal version (in hex, "0x" prefixed)*/
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Old kexec-tools can not load new kernels. The reason is kexec-tools does
not fill efi_info in x86 setup header previously, thus EFI failed to
initialize. In new kexec-tools it will by default to fill efi_info and
pass other EFI required infomation to 2nd kernel so kexec kernel EFI
initialization can succeed finally.
To prevent from breaking userspace, add a new xloadflags bit so
kexec-tools can check the flag and switch to old logic.
Signed-off-by: Dave Young <dyoung@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This adds support for the Marvell Tauros3 cache controller which
is compatible with pl310 cache controller but broadcasts L1 cache
operations to L2 cache. While updating the binding documentation,
clean up the list of possible compatibles. Also reorder driver
compatibles to allow non-ARM derivated to be compatible to ARM
cache controller compatibles.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the external clock outputs on the
Allwinner A20 SoC. The clock outputs are similar to "module 0"
type clocks, with different offsets and widths for clock factors.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Emilio López <emilio@elopez.com.ar>
This commit implements support for the "module 0" type of clocks, as
used by MMC, IR, NAND, SATA and other components.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit implements PLL5 and PLL6 support on the sunxi clock driver.
These PLLs use a similar factor clock, but differ on their outputs.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Mike Turquette <mturquette@linaro.org>
This commit adds gating support to PLL1 on the clock driver. This makes
the PLL1 implementation fully compatible with PLL4 as well.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Two drivers are merged through for 3.14:
- The A10/A20 RTC driver
- The A31 reset controller IP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=7spL
-----END PGP SIGNATURE-----
Merge tag 'sunxi-drivers-for-3.14' of https://github.com/mripard/linux into next/drivers
From Maxime Ripard:
Allwinner SoC additions for 3.14
Two drivers are merged through for 3.14:
- The A10/A20 RTC driver
- The A31 reset controller IP
* tag 'sunxi-drivers-for-3.14' of https://github.com/mripard/linux:
ARM: sun4i/sun7i: RTC driver
ARM: sun4i/sun7i: DT documentation for RTC driver
reset: Add Allwinner SoCs Reset Controller Driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Bringing in the tegra dma/reset framework cleanup as a base for the DT changes.
* tegra/dma-reset-rework: (320 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add support for the Trusted Foundations secure-mode firmware, as found
on NVIDIA SHIELD. This allows Linux to run in non-secure mode on this
board; all previous Tegra support has assumed the kernel is running in
secure mode.
This branch is based on v3.13-rc1, and shouldn't cause any merge
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=c5t/
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-trusted-foundations' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
From Stephen Warren:
ARM: tegra: Trusted Foundations firmware support
Add support for the Trusted Foundations secure-mode firmware, as found
on NVIDIA SHIELD. This allows Linux to run in non-secure mode on this
board; all previous Tegra support has assumed the kernel is running in
secure mode.
(The base TF support has been discussed back and forth a lot; for now
the most logical place for it seems to be under arch/arm, so we're adding
it here. We can move it out to a common location in the future if needed).
* tag 'tegra-for-3.14-trusted-foundations' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: support Trusted Foundations by default
ARM: tegra: set CPU reset handler using firmware
ARM: tegra: split setting of CPU reset handler
ARM: tegra: add support for Trusted Foundations
of: add Trusted Foundations bindings documentation
of: add vendor prefix for Trusted Logic Mobility
ARM: add basic support for Trusted Foundations
Signed-off-by: Olof Johansson <olof@lixom.net>
Bringing in the tegra dma/reset rework as a base for new SoC branches.
* tegra/dma-reset-rework: (81 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/cleanup
From Stephen Warren:
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
* tag 'tegra-for-3.14-dmas-resets-rework' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: (30 commits)
spi: tegra: checking for ERR_PTR instead of NULL
ASoC: tegra: update module reset list for Tegra124
clk: tegra: remove bogus PCIE_XCLK
clk: tegra: remove legacy reset APIs
ARM: tegra: remove legacy DMA entries from DT
ARM: tegra: remove legacy clock entries from DT
USB: EHCI: tegra: use reset framework
Input: tegra-kbc - use reset framework
serial: tegra: convert to standard DMA DT bindings
serial: tegra: use reset framework
spi: tegra: convert to standard DMA DT bindings
spi: tegra: use reset framework
staging: nvec: use reset framework
i2c: tegra: use reset framework
ASoC: tegra: convert to standard DMA DT bindings
ASoC: tegra: allocate AHUB FIFO during probe() not startup()
ASoC: tegra: call pm_runtime APIs around register accesses
ASoC: tegra: use reset framework
dma: tegra: register as an OF DMA controller
dma: tegra: use reset framework
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merging in external dependencies for the Tegra DMA and reset controller
refactoring from external trees.
Per Stephen Warren, the stability of these branches have been negotiated
with the relevant parties (Vinod/Mark/Mike)
* depends/asoc-dma:
ASoC: dmaengine: fix deferred probe detection
ASoC: dmaengine: support deferred probe for DMA channels
dma: add channel request API that supports deferred probe
ASoC: dmaengine: add custom DMA config to snd_dmaengine_pcm_config
ASoC: don't leak on error in snd_dmaengine_pcm_register
ASoC: restructure dmaengine_pcm_request_chan_of()
ASoC: generic-dmaengine-pcm: Set BATCH flag when residue reporting is not supported
ASoC: Add resource managed snd_dmaengine_pcm_register()
* depends/dma-of:
dma: add dma_get_any_slave_channel(), for use in of_xlate()
* depends/tegra-clk: (42 commits)
clk: tegra: fix __clk_lookup() return value checks
clk: tegra: Do not print errors for clk_round_rate()
clk: tegra: Initialize DSI low-power clocks
clk: tegra: add FUSE clock device
clk: tegra: Properly setup PWM clock on Tegra30
clk: tegra: Initialize secondary gr3d clock on Tegra30
clk: tegra114: Initialize clocks needed for HDMI
clk: tegra124: add suspend/resume function for tegra_cpu_car_ops
clk: tegra124: add wait_for_reset and disable_clock for tegra_cpu_car_ops
clk: tegra124: Add support for Tegra124 clocks
clk: tegra124: Add new peripheral clocks
clk: tegra124: Add common clk IDs to clk-id.h
clk: tegra: add TEGRA_PERIPH_NO_GATE
clk: tegra: add locking to periph clks
clk: tegra: Add periph regs bank X
clk: tegra: Add support for PLLSS
clk: tegra: move tegra20 to common infra
clk: tegra: move tegra30 to common infra
clk: tegra: introduce common gen4 super clock
clk: tegra: move PMC, fixed clocks to common files
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch describes the inline_data support in f2fs document.
Signed-off-by: Huajun Li <huajun.li@intel.com>
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
This patch adds OF parser support for davinci gpio
driver and also appropriate documentation in gpio-davinci.txt
located at Documentation/devicetree/bindings/gpio/.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: KV Sujith <sujithkv@ti.com>
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
[prabhakar.csengg@gmail.com: simplified the OF code, removed
unnecessary DT property and also simplified
the commit message]
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Whfv
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
2nd round of new IIO drivers, features and cleanups for the 3.14 cycle.
New drivers
* HID inclinometer driver.
* DHT11 humidity driver. Note that previous humidity drivers have been in
hwmon, but no one was ever entirely happy with that, and they should find
a more comfortable home in IIO (their original placement in hwmon was my
fault - oops). As this is our first humidity driver, core support is also
added.
New features
* Two of mxs-lradc channels are internally wired to a temperature sensor,
make this explicit in the driver by providing the relevant temperature
channel.
* Add support for blocking IO on buffers.
* Add a data_available call back to the interface between buffer implementations
and the core. This is much cleaner than the old, 'stufftoread' flag.
Implemented in the kfifo buffer.
Cleanups
* Last user of the old event configuration interface is converted and the
old interface dropped. Nice to be rid of this thanks to Lars-Peter's hard
work!
* Replace all remaining instances of the IIO_ST macro with explicit filling
of the scan_type structure within struct iio_chan_spec. This macro was a
bad idea, that rapidly ceased to cover all elements of the structure.
Miss reading of the macro arguements has led to a number of bugs so lets
just get rid of it. The final removal patch is awaiting for some fixes
to make their way into mainline.
In a couple of drivers, no elements of scan_type were even being used so
in those case, it has been dropped entirely.
* Drop a couple of of_match_ptr helper uses in drivers where devicetree is
not optional and hence the structures being protected by this always exist.
* Fix up some cases where data was read from a device in a particular
byte order, but he code placed it into a s16 or similar. These were
highlighted by Sparse.
* Use the new ATTRIBUTE_GROUPS macro to drop some boiler plate in the triggers
core code.
* ad7746 and ad7280a - stop storing buffers on the stack, giving cleaner code
and possibly avoiding issues with i2c bus drivers that assume they can dma
directly into the buffer. Note that this cannot currently happen as the the
i2c_smbus_read_i2c_block_data function has a memcpy from the buffer actually
passed to the bus driver. I missed this element of the commit message
and don't think it is major enough to rebase the iio tree.
* ad5791 and ad5504 stop storing buffers on the stack for an SPI driver.
Unlike the i2c drivers, this is a real issue for SPI drivers which can dma
directly into the buffer supplied.
Pull block fixes from Jens Axboe:
- fix for a memory leak on certain unplug events
- a collection of bcache fixes from Kent and Nicolas
- a few null_blk fixes and updates form Matias
- a marking of static of functions in the stec pci-e driver
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: support submit_queues on use_per_node_hctx
null_blk: set use_per_node_hctx param to false
null_blk: corrections to documentation
null_blk: warning on ignored submit_queues param
null_blk: refactor init and init errors code paths
null_blk: documentation
null_blk: mem garbage on NUMA systems during init
drivers: block: Mark the functions as static in skd_main.c
bcache: New writeback PD controller
bcache: bugfix for race between moving_gc and bucket_invalidate
bcache: fix for gc and writeback race
bcache: bugfix - moving_gc now moves only correct buckets
bcache: fix for gc crashing when no sectors are used
bcache: Fix heap_peek() macro
bcache: Fix for can_attach_cache()
bcache: Fix dirty_data accounting
bcache: Use uninterruptible sleep in writeback
bcache: kthread don't set writeback task to INTERUPTIBLE
block: fix memory leaks on unplugging block device
bcache: fix sparse non static symbol warning
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
Document the device tree bindings for the sci serial port devices.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=YqMd
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT 2nd updates for v3.14
- add DMA controller, SPI, and TMU DT nodes for exynos5420
- add PWM DT nodes for exynos5250 and exynos5420
- drop interrupt controller properties from MCT nodes
because MCT is not an interrupt controller
- move MCT nodes to exynos4x12 from board because it is
a per-processor interrupt and same 4212 and 4412
- use one cell for MCT interrupt map for exynos4 SoCs
- update Exynos MCT DT bindings accordingly
- fix missing spaces after labels for exynos
- fix mmc status property for exynos5250-snow
- add MCLK for codec for exynos5250-smdk5250
- disable SPI and I2C by default for exynos5250 SoC
and enable into requiring some boards
- rename cros5250-common to exynos5250-cros-common
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (27 commits)
ARM: dts: Rename Exynos5250 ChromeOS common file to have exynos prefix
ARM: dts: Disable I2C controllers by default on Exynos5250
ARM: dts: Leave Exynos5250 SPI controller disabled by default
ARM: dts: Add CODEC MCLK for SMDK5250
ARM: dts: Add device nodes for TMU blocks for exynos5420
ARM: dts: Fix status property of mmc nodes for snow board
ARM: dts: Fix missing spaces after labels for exynos
ARM: dts: Simplify MCT interrupt map for exynos4 SoCs
ARM: dts: Move MCT node to exynos4x12.dtsi
ARM: dts: Drop interrupt controller properties from MCT nodes for exynos4 SoCs
Documentation: devicetree: Update Exynos MCT bindings description
ARM: dts: add pwm DT nodes to Exynos5250 and Exynos5420
ARM: dts: Add SPI nodes to the exynos5420 device tree file
ARM: dts: Add DMA controller node info on Exynos5420
ARM: dts: Use MSHC controller for eMMC memory for exynos4412-trats2
ARM: dts: Fix definition of MSHC device tree nodes for exynos4x12
ARM: dts: add clock provider for mshc node for Exynos4412 SOC
clk: samsung: exynos4: Fix definition of div_mmc_pre4 divider
ARM: dts: Fix exynos5250-snow's search key to be L_META
ARM: dts: Add the missing "\" key in non-US keyboards for exynos5250-snow
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add devicetree binding documentation for isp1704-charger.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This adds an UDC driver for GRUSBDC USB Device Controller cores available in the
GRLIB VHDL IP core library. The driver only supports DMA mode.
Signed-off-by: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ams AS3722 device supports the power off by turning off its all rails.
Add dt node properties to enable this functionality on this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager can parse charger_desc data from devicetree which is used
to register charger manager.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add a binding that describes the Broadcom Kona USB2 PHY found
on the BCM281xx family of SoCs.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2/s3c-hsotg require a single clock to be specified and optionally
a generic phy. On the s3c-hsotg driver old style USB phy support is
present as a fallback so the generic phy properties are optional.
Signed-off-by: Matt Porter <mporter@linaro.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSt1TYAAoJEHm+PkMAQRiGvWgH/iWg8TmEWz4KUKuHthuUi0uh
9+2YDN+4k577Xa0obaG24giQeqkCdxMr3oJrS3FO9jeAmaNRHEGhxUPneisb7RtN
9jIVsz5bPa9/DcK9nqtaUQdvA0O5AWTE6AAPmwleTVy+8CygBo987T2uGELnQCSR
FrKCrMePc7Pj0uthMVXrpJ17Ffm/j7jkfRtPhrxHJyngh3jEux+tPbpynH/aKuO2
47unsSQimoFk7n2SPFvNu3E/vZE2xVbu5SH9MCl5yyiCifFjpi3B71LV/FW51lvm
cK8Jzn2BmYDygRFjnZfq4zJHqYJCBHzpjCLWmR37Dm/JS91aGq3+Cg0stDP8UTs=
=+Hcn
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc5' into next
Linux 3.13-rc5
* tag 'v3.13-rc5': (231 commits)
Linux 3.13-rc5
aio: clean up and fix aio_setup_ring page mapping
aio/migratepages: make aio migrate pages sane
aio: fix kioctx leak introduced by "aio: Fix a trinity splat"
Don't set the INITRD_COMPRESS environment variable automatically
mm: fix build of split ptlock code
pstore: Don't allow high traffic options on fragile devices
mm: do not allocate page->ptl dynamically, if spinlock_t fits to long
mm: page_alloc: revert NUMA aspect of fair allocation policy
Revert "mm: page_alloc: exclude unreclaimable allocations from zone fairness policy"
mm: Fix NULL pointer dereference in madvise(MADV_WILLNEED) support
qla2xxx: Fix scsi_host leak on qlt_lport_register callback failure
target: Remove extra percpu_ref_init
arm64: ptrace: avoid using HW_BREAKPOINT_EMPTY for disabled events
ARC: Allow conditional multiple inclusion of uapi/asm/unistd.h
target/file: Update hw_max_sectors based on current block_size
iser-target: Move INIT_WORK setup into isert_create_device_ib_res
iscsi-target: Fix incorrect np->np_thread NULL assignment
mm/hugetlb: check for pte NULL pointer in __page_check_address()
fix build with make 3.80
...
Conflicts:
drivers/usb/phy/Kconfig
The frequency for the Kona timer can either be specified through the
device tree or determined by checking the rate of the clock specified
in the device tree. Update the documentation to reflect both ways.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
The Kona SDHCI block requires a clock that must be specified in the
device tree. Update the documentation to reflect this requirement.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
This patch adds support for accuracy retrieval on fixed clocks.
It also adds a new dt property called 'clock-accuracy' to define the clock
accuracy.
This can be usefull for oscillator (RC, crystal, ...) definitions which are
always given an accuracy characteristic.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock accuracy is expressed in ppb (parts per billion) and represents
the possible clock drift.
Say you have a clock (e.g. an oscillator) which provides a fixed clock of
20MHz with an accuracy of +- 20Hz. This accuracy expressed in ppb is
20Hz/20MHz = 1000 ppb (or 1 ppm).
Clock users may need the clock accuracy information in order to choose
the best clock (the one with the best accuracy) across several available
clocks.
This patch adds clk accuracy retrieval support for common clk framework by
means of a new function called clk_get_accuracy.
This function returns the given clock accuracy expressed in ppb.
In order to get the clock accuracy, this implementation adds one callback
called recalc_accuracy to the clk_ops structure.
This callback is given the parent clock accuracy (if the clock is not a
root clock) and should recalculate the given clock accuracy.
This callback is optional and may be implemented if the clock is not
a perfect clock (accuracy != 0 ppb).
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add support for using emev2 SMU clocks with DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=NhhY
-----END PGP SIGNATURE-----
Merge tag 'renesas-clock-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into clk-next-shmobile2
Renesas ARM based SoC Clock updates for v3.14
Add support for using emev2 SMU clocks with DT
This patch introduces new sysfs entries for users to control the policy of
in-place-updates, namely IPU, in f2fs.
Sometimes f2fs suffers from performance degradation due to its out-of-place
update policy that produces many additional node block writes.
If the storage performance is very dependant on the amount of data writes
instead of IO patterns, we'd better drop this out-of-place update policy.
This patch suggests 5 polcies and their triggering conditions as follows.
[sysfs entry name = ipu_policy]
0: F2FS_IPU_FORCE all the time,
1: F2FS_IPU_SSR if SSR mode is activated,
2: F2FS_IPU_UTIL if FS utilization is over threashold,
3: F2FS_IPU_SSR_UTIL if SSR mode is activated and FS utilization is over
threashold,
4: F2FS_IPU_DISABLE disable IPU. (=default option)
[sysfs entry name = min_ipu_util]
This parameter controls the threshold to trigger in-place-updates.
The number indicates percentage of the filesystem utilization, and used by
F2FS_IPU_UTIL and F2FS_IPU_SSR_UTIL policies.
For more details, see need_inplace_update() in segment.h.
Signed-off-by: Jaegeuk Kim <jaegeuk.kim@samsung.com>
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=6e6p
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
From Kukjin Kim:
Samsung DT updates for v3.14
- Add support Octa Cores for exynos5420
: populate CPU node entries to 8 Cores
: extend mct to support 8 local interrupts
- Update dwmmc nodes for exynos5250 and exynos5420
: change status property of dwmmc nodes for exynos5250
: move dwmmc nodes from exynos5 to exynos5250 because
it's different between exynos5250 and exynos5420
: rename mmc nodes from dwmmc for exynos5 SoCs
: add dwmmc nodes for exynos5420
- Add G-Scaler nodes for exynos5420
- Add HS-i2c nodes in exynos5420
: High Speed I2C 7 channels (4 to 10)
- Update sysreg binding and node name in exynos4
- Update min voltage on exynos5250-arndale
- Move fifo-depth property from boards to exynos5250 SoC
: because the fifo-depth property is SoC specific
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Update Samsung sysreg binding document
ARM: dts: Fix sysreg node name in exynos4.dtsi
ARM: dts: Add hs-i2c nodes to exynos5420
ARM: dts: Update min voltage for vdd_arm on Arndale
ARM: dts: populate cpu node entries to 8 cpus for exynos5420
clocksource: mct: extend mct to support 8 local interrupts for Exynos5420
ARM: dts: Add device nodes for GScaler blocks for exynos5420
ARM: dts: Add dwmmc DT nodes for exynos5420 SOC
ARM: dts: rename mmc dts node for exynos5 series
ARM: dts: Move fifo-depth property from exynos5250 board dts
ARM: dts: change status property of dwmmc nodes for exynos5250
ARM: dts: Move dwmmc nodes from exynos5.dtsi to exynos5250.dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a generic (dtsi) include file for MOXA ART SoCs.
Also add a file for UC-7112-LX.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSqfkKAAoJEAf03oE53VmQpHoH/2OnDX5C3hqXXL1r3p6JjRLP
B2xDO2iZcB340HrobInN0FONXVCA2b8yNy2G+U421sNjklivT4o9+66tiwBBQlbS
uoYU95CgeBs5dU1iM8Z5cIRFphEZdKDAJDd0RABUEcVPa+w569nyi5V29rwzH0UZ
hnW0IzUtJqo9344dfBai9cRcVOjrJHfiqB+05PUWb12KFbLaQhqQLL1Z5b0XasB/
9htaMxuXMXhflP7m+JY0+uVlFTOJliY9zUMN/bOqT2VBrl2tt1xLW7nooM57dB3y
+wK1A+mhYHQgEgVm1U6X3+LUluitwyA+yw2Ybf6Yi/T+3tzMjeiknfHfUB5afMY=
=JTE6
-----END PGP SIGNATURE-----
Merge tag 'at91-drivers' of git://github.com/at91linux/linux-at91 into next/drivers
From Nicolas Ferre:
AT91 crypto drivers DT support:
- add DT to sha/des/aes existing drivers
- add DMA DT
- all documentation added to crypto/atmel-crypto.txt file
* tag 'at91-drivers' of git://github.com/at91linux/linux-at91:
crypto: atmel-sha - add sha information to the log
crypto: atmel-sha - add support for Device Tree
crypto: atmel-tdes - add support for Device Tree
crypto: atmel-aes - add support for Device Tree
Signed-off-by: Olof Johansson <olof@lixom.net>
Intersil ISL12057 is an I2C RTC chip also supporting two alarms. This
patch only adds support for basic RTC functionalities (i.e. getting
and setting time). Tests have been performed on NETGEAR ReadyNAS 102
w/ startup/shutdown scripts, hwclock, ntpdate and openntpd.
Reviewed-by: Mark Brown <broonie@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add infrastructure to handle distributor and cpu interface register
accesses through the KVM_{GET/SET}_DEVICE_ATTR interface by adding the
KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_CPU_REGS groups
and defining the semantics of the attr field to be the MMIO offset as
specified in the GICv2 specs.
Missing register accesses or other changes in individual register access
functions to support save/restore of the VGIC state is added in
subsequent patches.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Support setting the distributor and cpu interface base addresses in the
VM physical address space through the KVM_{SET,GET}_DEVICE_ATTR API
in addition to the ARM specific API.
This has the added benefit of being able to share more code in user
space and do things in a uniform manner.
Also deprecate the older API at the same time, but backwards
compatibility will be maintained.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Support creating the ARM VGIC device through the KVM_CREATE_DEVICE
ioctl, which can then later be leveraged to use the
KVM_{GET/SET}_DEVICE_ATTR, which is useful both for setting addresses in
a more generic API than the ARM-specific one and is useful for
save/restore of VGIC state.
Adds KVM_CAP_DEVICE_CTRL to ARM capabilities.
Note that we change the check for creating a VGIC from bailing out if
any VCPUs were created, to bailing out if any VCPUs were ever run. This
is an important distinction that shouldn't break anything, but allows
creating the VGIC after the VCPUs have been created.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
The defaults for the module is to instantiate itself with blk-mq and a
submit queue for each CPU node in the system.
To save resources, initialize instead with a single submit queue.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Randy Dunlap reported a couple of grammar errors and unfortunate usages of
socket/node/core.
Signed-off-by: Matias Bjorling <m@bjorling.me>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kexec kernel will need exactly same mapping for EFI runtime memory
ranges. Thus here export the runtime ranges mapping to sysfs,
kexec-tools will assemble them and pass to 2nd kernel via setup_data.
Introducing a new directory /sys/firmware/efi/runtime-map just like
/sys/firmware/memmap. Containing below attribute in each file of that
directory:
attribute num_pages phys_addr type virt_addr
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Export fw_vendor, runtime and config table physical addresses to
/sys/firmware/efi/{fw_vendor,runtime,config_table} because kexec kernels
need them.
From EFI spec these 3 variables will be updated to virtual address after
entering virtual mode. But kernel startup code will need the physical
address.
Signed-off-by: Dave Young <dyoung@redhat.com>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
tps65910 has a backup battery charger with a configurable voltage. This
patch adds a regulator for the backup battery.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Device Tree support to the Microchip MCP251X driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce TP_STATUS_VLAN_TPID_VALID bit into the documentation.
Signed-off-by: Atzm Watanabe <atzm@stratosphere.co.jp>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates description of device tree bindings for Exynos MCT
(multicore timers). Namely:
- added note about simplified specification of local timer interrupts,
when using single per-processor interrupt for all local timers,
- changed first example that was incorrectly suggesting that global
timer interrupts are optional,
- simplified example interrupt map,
- added example showing simplified local timer interrupt specification.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add DT documentation for SUNXI RTC driver
Signed-off-by: Carlo Caione <carlo.caione@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
* pci/msi:
PCI/MSI: Make pci_enable_msi/msix() 'nvec' argument type as int
PCI/MSI: Return -ENOSYS for unimplemented interfaces, not -1
PCI/MSI: Return msix_capability_init() failure if populate_msi_sysfs() fails
s390/PCI: Remove superfluous check of MSI type
s390/PCI: Fix single MSI only check
PCI/MSI: Export MSI mode using attributes, not kobjects
From Uwe Kleine-König:
* efm32/soc: (1003 commits)
ARM: device trees for Energy Micro's EFM32 Cortex-M3 SoCs
ARM: new platform for Energy Micro's EFM32 Cortex-M3 SoCs
+Linux 3.13-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Make pci_enable_msi_block(), pci_enable_msi_block_auto() and
pci_enable_msix() consistent with regard to the type of 'nvec' argument.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tejun Heo <tj@kernel.org>
During the last media summit meeting it was decided to move this driver to
staging as the first step to removing it altogether.
Most webcams covered by this driver are now supported by gspca. Nobody has the
hardware to convert the remaining devices to gspca.
This driver needs a major overhaul to have it conform to the latest frameworks
and compliancy tests.
Without hardware, however, this is next to impossible. Given the fact that
this driver seems to be pretty much unused (it has been removed from Fedora
several versions ago and nobody complained about that), we decided to drop
this driver.
This patch moves it to staging. Some time in 2014 we will drop it completely.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Luca Risolia <luca.risolia@studio.unibo.it>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This commit adds support for both DSI outputs found on Tegra. Only very
minimal functionality is implemented, so advanced features like ganged
mode won't work.
Due to the lack of other test hardware, some sections of the driver are
hardcoded to work with Dalmore.
Signed-off-by: Thierry Reding <treding@nvidia.com>
In some use cases Zynq's FPGA clocks are used as static clock
generators for IP in the FPGA part of the SOC for which no Linux driver
exists and would control those clocks. To avoid automatic
gating of these clocks in such cases a new property - fclk-enable - is
added to the clock controller's DT description to accomodate such use
cases. It's value is a bitmask, where a set bit results in enabling
the corresponding FCLK through the clkc.
FPGA clocks are handled following the rules below:
If an FCLK is not enabled by bootloaders, that FCLK will be disabled in
Linux. Drivers can enable and control it through the CCF as usual.
If an FCLK is enabled by bootloaders AND the corresponding bit in the
'fclk-enable' DT property is set, that FCLK will be enabled by the clkc,
resulting in an off by one reference count for that clock. Ensuring it
will always be running.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2013-12-19
1) Use the user supplied policy index instead of a generated one
if present. From Fan Du.
2) Make xfrm migration namespace aware. From Fan Du.
3) Make the xfrm state and policy locks namespace aware. From Fan Du.
4) Remove ancient sleeping when the SA is in acquire state,
we now queue packets to the policy instead. This replaces the
sleeping code.
5) Remove FLOWI_FLAG_CAN_SLEEP. This was used to notify xfrm about the
posibility to sleep. The sleeping code is gone, so remove it.
6) Check user specified spi for IPComp. Thr spi for IPcomp is only
16 bit wide, so check for a valid value. From Fan Du.
7) Export verify_userspi_info to check for valid user supplied spi ranges
with pfkey and netlink. From Fan Du.
8) RFC3173 states that if the total size of a compressed payload and the IPComp
header is not smaller than the size of the original payload, the IP datagram
must be sent in the original non-compressed form. These packets are dropped
by the inbound policy check because they are not transformed. Document the need
to set 'level use' for IPcomp to receive such packets anyway. From Fan Du.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCI MSI sysfs code is a mess with kobjects for things that don't really
need to be kobjects. This patch creates attributes dynamically for the MSI
interrupts instead of using kobjects.
Note, this removes a directory from sysfs. Old MSI kobjects:
pci_device
└── msi_irqs
└── 40
└── mode
New MSI attributes:
pci_device
└── msi_irqs
└── 40
As there was only one file "mode" with the kobject model, the interrupt
number is now a file that returns the "mode" of the interrupt (msi vs.
msix).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Marc Kleine-Budde says:
====================
this is a pull request of four patches for net-next/master.
There is one patch by Markus Pargmann, which speeds up the c_can
driver, a patch by John Whitmore which updates the in tree
documentation. A patch by Jeff Kirsher which replaces the FSF's address
by a link and a patch by Alexander Shiyan which converts the mcp251x
driver to make use of managed resources.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes two spelling mistakes in the design pattern doc.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some boards do not have a PCIe reset GPIO. To avoid probe failure on these
boards, make the reset GPIO optional as well.
[bhelgaas: whitespace fixes]
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Frank Li <lznuaa@gmail.com>
Cc: Harro Haan <hrhaan@gmail.com>
Cc: Mohit KUMAR <Mohit.KUMAR@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Richard Zhu <r65037@freescale.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Siva Reddy Kallam <siva.kallam@samsung.com>
Cc: Srikanth T Shivanand <ts.srikanth@samsung.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Yinghai Lu <yinghai@kernel.org>
VFIO currently allocates it's own dynamic chardev range, reserving the
first minor for the control part of the interface (/dev/vfio/vfio) and
the remainder for VFIO groups (/dev/vfio/$GROUP). This works, but it
doesn't support auto loading. For instance when libvirt checks for
VFIO support it looks for /dev/vfio/vfio, which currently doesn't
exist unless the vfio module is loaded. By converting the control
device to a misc driver and reserving a static minor, we can enable
auto loading.
Reserving the minor is a prerequist to that conversion. Minor 196
is unused by anything currently in the kernel.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The documentation has gone out-of-sync, so update it to
the current status.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
After getting warnings in an allyesconfig build[1] from this
driver, I decided to remind myself just how old it was, and
whether it warranted fixing. In the Kconfig help text, I found:
"This driver will eventually be phased out entirely"
Going back to the history archive, I see the line was added[2]
in Feb 2002, when we moved from v2.4.2.1 ---> v2.4.2.2
So, with over a decade of notification, and multiple major releases
since then, I think we can justify removing this. Currently we have
people wasting time building it during routine testing, and then
wasting more time re-researching the known reported warnings, only to
find that nobody really is willing to integrate the fixes[3] for it.
A quick search didn't seem to indicate any active user base for it.
If someone happens to have a quirky _old_ card that the eleven year
old "new" driver doesn't work with, then it is entirely reasonable
that they stick with a kernel version that predates this removal.
[1] drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_register’:
drivers/scsi/aic7xxx_old.c:7901:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch]
drivers/scsi/aic7xxx_old.c:7898:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch]
drivers/scsi/aic7xxx_old.c: In function ‘aic7xxx_load_seeprom’:
drivers/scsi/aic7xxx_old.c:8517:5: warning: case value ‘257’ not in enumerated type ‘ahc_chip’ [-Wswitch]
drivers/scsi/aic7xxx_old.c:8510:5: warning: case value ‘513’ not in enumerated type ‘ahc_chip’ [-Wswitch]
[2] http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git commit 44e8778c
[3] https://lkml.org/lkml/2012/10/29/215
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Acked-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The sentence is not proper English, so the use of "general" is now replaced with
"in general". "generally" was also considered, but "in general" is probably the
correct in this case.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This adds omap control module support for USBSS in AM437x SoC.
Update DT binding information to reflect these changes.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Linux 3.13-rc4
* tag 'v3.13-rc4': (1001 commits)
Linux 3.13-rc4
null_blk: mem garbage on NUMA systems during init
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Revert "selinux: consider filesystem subtype in policies"
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
ARM: fix asm/memory.h build error
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
...
Signed-off-by: Felipe Balbi <balbi@ti.com>
These update binding information for ti qspi controller.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Sysfs interfaces for the GenWQE card. There are attributes to query
the version of the bitstream as well as some for the driver. For
debugging, please also see the debugfs interfaces of this driver.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Co-authors: Joerg-Stephan Vogt <jsvogt@de.ibm.com>,
Michael Jung <MIJUNG@de.ibm.com>,
Michael Ruettger <michael@ibmra.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Debugfs interfaces for the GenWQE card. Help to debug potential
problems. Dump internal chip state for debugging and failure
determination.
Signed-off-by: Frank Haverkamp <haver@linux.vnet.ibm.com>
Co-authors: Joerg-Stephan Vogt <jsvogt@de.ibm.com>,
Michael Jung <MIJUNG@de.ibm.com>,
Michael Ruettger <michael@ibmra.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the clock properties required by the atmel-ssc driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the clock properties required by the atmel_tclib driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull crypto key patches from David Howells:
"There are four items:
- A patch to fix X.509 certificate gathering. The problem was that I
was coming up with a different path for signing_key.x509 in the
build directory if it didn't exist to if it did exist. This meant
that the X.509 cert container object file would be rebuilt on the
second rebuild in a build directory and the kernel would get
relinked.
- Unconditionally remove files generated by SYSTEM_TRUSTED_KEYRING=y
when doing make mrproper.
- Actually initialise the persistent-keyring semaphore for
init_user_ns. I have no idea why this works at all for users in
the base user namespace unless it's something to do with systemd
containerising the system.
- Documentation for module signing"
* 'keys-devel' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
Add Documentation/module-signing.txt file
KEYS: fix uninitialized persistent_keyring_register_sem
KEYS: Remove files generated when SYSTEM_TRUSTED_KEYRING=y
X.509: Fix certificate gathering
This new mode discards all incoming fragmentation-needed notifications
as I guess was originally intended with this knob. To not break backward
compatibility too much, I only added a special case for mode 2 in the
receiving path.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the Document for Freescale SAI driver under
Documentation/devicetree/bindings/sound/.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix some typos and while at it also use "PS" as the name for the central
"HOME" button on Sony controllers, this is how Sony itself calls it.
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This feature extends the generic cryptographic device driver (zcrypt)
with a new capability to service EP11 requests for the Crypto Express4S
card in EP11 (Enterprise PKCS#11 mode) coprocessor mode.
Signed-off-by: Ingo Tuchscherer <ingo.tuchscherer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This patch enables the JPEG codec on S5PV210 and Exynos4210 SoCs. There are
some differences in newer versions of the JPEG codec IP on SoCs like Exynos4x12
and Exynos5 series and support for them will be added in subsequent patches.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add board support with device tree for Hisilicon Hi3620 SoC platform.
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
[khilman: fix checkpatch errors]
[khilman: fold in patch which selects GPIO in Kconfig]
Signed-off-by: Kevin Hilman <khilman@linaro.org>
When I added support for ACPI5 I made the assumption that
injected processor errors would just need to know the APICID,
memory errors just the address and mask, and PCIe errors just the
segment/bus/device/function. So I had the code check the type of injection
and multiplex the "param1" value appropriately.
This was not a good assumption :-(
There are injection scenarios where we need to specify more than one of
these items. E.g. injecting a cache error we need to specify an APICID
of the cpu that owns the cache, and also an address (so that we can trip
the error by accessing the address).
Add a "flags" file to give the user direct access to specify which items
are valid in the ACPI SET_ERROR_TYPE_WITH_ADDRESS structure. Also add
new files param3 and param4 to hold all these values.
For backwards compatability with old injection scripts we maintain the
old behaviour if flags remains set at zero (or is reset to 0).
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix minor typo in "Parameters:" of KVM_ARM_VCPU_INIT documentation.
Signed-off-by: Anup Patel <anup.patel@linaro.org>
Signed-off-by: Pranavkumar Sawargaonkar <pranavkumar@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Document the clock properties required by the at91 usart driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the devicetree documentation for the Cirrus Logic
CLPS711X UART.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce device tree bindings for the MIPI pad calibration controller
found on Tegra SoCs. The controller can be used to perform calibration
of pads used for DSI and CSI peripherals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The display controller primary clock was recently renamed to "dc", so
update the example to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use the DRM panel framework to attach a panel to an output. If the panel
attached to a connector supports supports the backlight brightness
accessors, a property will be available to allow the brightness to be
modified from userspace.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This binding specifies a set of common properties for display panels. It
can be used as a basis by bindings for specific panels.
Bindings for three specific panels are provided to show how the simple
panel binding can be used.
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Document the device tree bindings for the MIPI DSI bus. The MIPI Display
Serial Interface specifies a serial bus and a protocol for communication
between a host and up to four peripherals.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=8T7+
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.14-dmas-resets-rework' into drm/for-next
ARM: tegra: implement common DMA and resets DT bindings
This series converts the Tegra DTs and drivers to use the common/
standard DMA and reset bindings, rather than custom bindings. It also
adds complete documentation for the Tegra clock bindings without
actually changing any binding definitions.
This conversion relies on a few sets of patches in branches from outside
the Tegra tree:
1) A patch to add an DMA channel request API which allows deferred probe
to be implemented.
2) A patch to implement a common part of the of_xlate function for DMA
controllers.
3) Some ASoC patches (which in turn rely on (1) above), which support
deferred probe during DMA channel allocation.
4) The Tegra clock driver changes for 3.14.
Consequently, this branch is based on a merge of all of those external
branches.
In turn, this branch is or will be pulled into a few places that either
rely on features introduced here, or would otherwise conflict with the
patches:
a) Tegra's own for-3.14/powergate and for-4.14/dt branches, to avoid
conflicts.
b) The DRM tree, which introduces new code that relies on the reset
controller framework introduced in this branch, and to avoid
conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into core/locking
Merge Linux 3.13-rc4, to refresh this rather old tree with the latest fixes.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
commit 887c290e (sched/numa: Decide whether to favour task or group weights
based on swap candidate relationships) drop the check against
sysctl_numa_balancing_settle_count, this patch remove the sysctl.
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Link: http://lkml.kernel.org/r/1386833006-6600-1-git-send-email-liwanp@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Changed MAINTAINERS file to add Documentation/networking/can.txt to the list of
maintained files.
can.txt:
- Globally changed Socket CAN to SocketCAN
- Removed section 3.3 from the document
- Updated Section 7
- Corrected a few simple typos
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: John Whitmore <johnfwhitmore@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The Atmel PWM controller uses the standard device tree bindings for PWM
controllers.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=r//I
-----END PGP SIGNATURE-----
Merge tag 'ras_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
* Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Create Documentation/networking/ipsec.txt to document IPsec
corner issues and other info, which will be useful when user
deploying IPsec.
Signed-off-by: Fan Du <fan.du@windriver.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Historically, an UNLOCK+LOCK pair executed by one CPU, by one
task, or on a given lock variable has implied a full memory
barrier. In a recent LKML thread, the wisdom of this historical
approach was called into question:
http://www.spinics.net/lists/linux-mm/msg65653.html, in part due
to the memory-order complexities of low-handoff-overhead queued
locks on x86 systems.
This patch therefore removes this guarantee from the
documentation, and further documents how to restore it via a new
smp_mb__after_unlock_lock() primitive.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1386799151-2219-6-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The situations in which ACCESS_ONCE() is required are not well
documented, so this commit adds some verbiage to
memory-barriers.txt.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1386799151-2219-4-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
No SMP architecture currently supporting Linux allows
speculative writes, so this commit updates
Documentation/memory-barriers.txt to prohibit them in Linux core
code. It also records restrictions on their use.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1386799151-2219-3-git-send-email-paulmck@linux.vnet.ibm.com
[ Paul modified the original patch from Peter. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Although the atomic_long_t functions are quite useful, they are
a bit obscure. This commit therefore adds the common ones
alongside their atomic_t counterparts in
Documentation/memory-barriers.txt.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1386799151-2219-2-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Documentation/memory-barriers.txt file was written before
the need for ACCESS_ONCE() was fully appreciated. It therefore
contains no ACCESS_ONCE() calls, which can be a problem when
people lift examples from it. This commit therefore adds
ACCESS_ONCE() calls.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Reviewed-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-arch@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1386799151-2219-1-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use the preferred style sizeof(VARIABLE) instead of sizeof(TYPE) in the
joystick API documentation, Documentation/CodingStyle states that this
is the preferred style for allocations but using it elsewhere is good
too.
Also fix some errors like "sizeof(struct mybuffer)" which didn't mean
anything.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Nowadays the joystick device nodes are created under /dev/input, reflect
this in the documentation in order to make copy and paste easier for
users.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Synchronize with mainline to bring in the new keycode definitions and
new hwmon API.
This commit adds slew-rate and input-enable/disable support for pinconf
-generic.
Signed-off-by: Sherman Yin <syin@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the more specific form 8974 for the compatible to reduce the
risk of future mishaps.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new DMA_TYPE for SSI dual FIFO script, included
in SDMA firmware version 2. This script would allow SSI use dual
fifo mode to transimit/receive data without occasional hardware
underrun/overrun.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Kumar Gala <galak@codeaurora.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull networking fixes from David Miller:
1) Revert CHECKSUM_COMPLETE optimization in pskb_trim_rcsum(), I can't
figure out why it breaks things.
2) Fix comparison in netfilter ipset's hash_netnet4_data_equal(), it
was basically doing "x == x", from Dave Jones.
3) Freescale FEC driver was DMA mapping the wrong number of bytes, from
Sebastian Siewior.
4) Blackhole and prohibit routes in ipv6 were not doing the right thing
because their ->input and ->output methods were not being assigned
correctly. Now they behave properly like their ipv4 counterparts.
From Kamala R.
5) Several drivers advertise the NETIF_F_FRAGLIST capability, but
really do not support this feature and will send garbage packets if
fed fraglist SKBs. From Eric Dumazet.
6) Fix long standing user triggerable BUG_ON over loopback in RDS
protocol stack, from Venkat Venkatsubra.
7) Several not so common code paths can potentially try to invoke
packet scheduler actions that might be NULL without checking. Shore
things up by either 1) defining a method as mandatory and erroring
on registration if that method is NULL 2) defininig a method as
optional and the registration function hooks up a default
implementation when NULL is seen. From Jamal Hadi Salim.
8) Fix fragment detection in xen-natback driver, from Paul Durrant.
9) Kill dangling enter_memory_pressure method in cg_proto ops, from
Eric W Biederman.
10) SKBs that traverse namespaces should have their local_df cleared,
from Hannes Frederic Sowa.
11) IOCB file position is not being updated by macvtap_aio_read() and
tun_chr_aio_read(). From Zhi Yong Wu.
12) Don't free virtio_net netdev before releasing all of the NAPI
instances. From Andrey Vagin.
13) Procfs entry leak in xt_hashlimit, from Sergey Popovich.
14) IPv6 routes that are no cached routes should not count against the
garbage collection limits. We had this almost right, but were
missing handling addrconf generated routes properly. From Hannes
Frederic Sowa.
15) fib{4,6}_rule_suppress() have to consider potentially seeing NULL
route info when they are called, from Stefan Tomanek.
16) TUN and MACVTAP have had truncated packet signalling for some time,
fix from Jason Wang.
17) Fix use after frrr in __udp4_lib_rcv(), from Eric Dumazet.
18) xen-netback does not interpret the NAPI budget properly for TX work,
fix from Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
xen-netback: fix gso_prefix check
net: make neigh_priv_len in struct net_device 16bit instead of 8bit
drivers: net: cpsw: fix for cpsw crash when build as modules
xen-netback: napi: don't prematurely request a tx event
xen-netback: napi: fix abuse of budget
sch_tbf: use do_div() for 64-bit divide
udp: ipv4: must add synchronization in udp_sk_rx_dst_set()
net:fec: remove duplicate lines in comment about errata ERR006358
Revert "8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature"
8390 : Replace ei_debug with msg_enable/NETIF_MSG_* feature
xen-netback: make sure skb linear area covers checksum field
net: smc91x: Fix device tree based configuration so it's usable
udp: ipv4: fix potential use after free in udp_v4_early_demux()
macvtap: signal truncated packets
tun: unbreak truncated packet signalling
net: sched: htb: fix the calculation of quantum
net: sched: tbf: fix the calculation of max_size
micrel: add support for KSZ8041RNLI
...
Added a binding example for reference and updated the
node name. While at it also removed the name description
as it is not necessary.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
