This patch, provided by ST SPEAr developers,
has fixed a problem raised on ARM CA9 where
happened that the dma_transmission was enabled before
the dma descriptors were properly filled. To guarantee this
data memory barriers have been explicity used in the driver.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables software (and phy device) transmit time stamping
for the STMicroelectronics Ethernet driver. Compile tested only.
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@conan.davemloft.net>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bug in the set_pauseparam
function that didn't well manage the ANE
field and returned broken values when use
ethtool -A|-a.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver used to call phy's ethtool configuration routine to start
auto-negotiation. This change has it call directly phy's routine to
start auto-negotiation.
The initial version was hiding phy_start_aneg() return value,
this patch returns it (<0 upon error).
Tested: module compiles, tested on STM HDK7108 STB.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Karim Hamiti <karim.hamiti@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac.h uses struct platform_device and doesn't include
<linux/platform_device.h>. Whereas drivers/net/stmmac/stmmac.h includes it, but
doesn't directly use it. And so we get following compilation warning while using
this file:
warning: ‘struct platform_device’ declared inside parameter list
This patch includes <linux/platform_device.h> in linux/stmmac.h and removes it
from drivers/net/stmmac/stmmac.h
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure that when a driver calls the ethtool's
get/set_settings() callback of another driver, the data passed to it
is clean. This guarantees that speed_hi will be zeroed correctly if
the called callback doesn't explicitely set it: we are sure we don't
get a corrupted speed from the underlying driver. We also take care of
setting the cmd field appropriately (ETHTOOL_GSET/SSET).
This applies to dev_ethtool_get_settings(), which now makes sure it
sets up that ethtool command parameter correctly before passing it to
drivers. This also means that whoever calls dev_ethtool_get_settings()
does not have to clean the ethtool command parameter. This function
also becomes an exported symbol instead of an inline.
All drivers visible to make allyesconfig under x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some old MAC chips without COE sometime the
Transmit Underflow error is issued.
The driver aborted all the transmission process
and initialized it from scratch.
This breaks the network activity as raised by Nachiketa
on a SPEAr board.
The patch is to fix this rare underflow event.
The driver will only clear the interrupt and the Tx
DMA will go out the Suspend state as soon as the
descriptor is fetched again.
The driver will continue to bump-up the DMA FIFO threshold
that, indeed, helped somebody to prevent this kind of error
in the past as well.
Reported-by: Nachiketa Prachanda <nprachanda@ncomputing.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reviews the open function and fixes some
errors when exit with an error state.
It also moves the request_irq after core is initialized
when interrupts are properly masked.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a compilation error when build the
dwmac_lib with the DEBUG option enabled.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also removes TSO as it's made fully in software --- better to leave this
to networking core.
If the MAC features can be detected at probe time and not at open, then
stmmac_fix_features could be simplified by limiting hw_features. That's
also better for users as they don't see offloads being togglable but
never turned on.
Redundant fallbacks for TX csum are removed as it's already handled
by network core.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables it by default when the driver starts.
This has been required by many people and seems to actually be
useful on STB.
At any rate, the WoL modes can be selected and turned-on/off
by using the ethtool at run-time by users.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code had a several problems:
*) It had potential null dereferences of "priv" and "res".
*) It released the memory region before it was aquired.
*) It didn't free "ndev" after it was allocated.
*) It didn't call unregister_netdev() after calling stmmac_probe().
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted here.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETIF_F_HW_CSUM is a superset of NETIF_F_IP_CSUM+NETIF_F_IPV6_CSUM, but
some drivers miss the difference. Fix this and also fix UFO dependency
on checksumming offload as it makes the same mistake in assumptions.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To reproduce: if connman (http://connman.net/) is started,
inserting the stmmac module triggers a "BUG: spinlock bad magic on CPU#0".
Registering the device in stmmac_probe() sends a notification to connman
which brings the interface up before the lock is initialized.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit to convert to use the dev_pm_ops struct
introduces a bug. The shutdown flag is not yet used
because the hibernation on memory is done by using
the freeze callback.
Thanks to Vlad for having reported it.
Reported-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the PM support using the dev_pm_ops
and reviews the hibernation support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds in the plat_stmmacenet_data
the init and exit callbacks that can be used
for invoking specific platform functions.
For example, on ST targets, these call the
PAD manager functions to set PIO lines and
syscfg registers.
The patch removes the stmmac_claim_resource
only used on STM Kernels as well.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies-up the stmmac_priv structure
that had many fileds alredy defined in the
plat_stmmacenet_data structure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables and disables the rx and tx bits in the MAC control reg
by using a single write operation.
This also solves a possible problem (spotted on SPEAr platforms) at 10Mbps
where two consecutive writes to a MAC control register can take more than
4 phy_clk cycles.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These tables only contain function pointers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Gustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver does not compile on s390:
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_adjust_link':
drivers/net/stmmac/stmmac_main.c:210: error: implicit declaration of function 'readl'
drivers/net/stmmac/stmmac_main.c:263: error: implicit declaration of function 'writel'
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
drivers/net/stmmac/stmmac_main.c:1674: error: implicit declaration of function 'ioremap'
drivers/net/stmmac/stmmac_main.c:1674: warning: assignment makes pointer from integer without a cast
drivers/net/stmmac/stmmac_main.c:1761: error: implicit declaration of function 'iounmap'
make[3]: *** [drivers/net/stmmac/stmmac_main.o] Error 1
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PM support is available this is passed
through the platform instead to be hard-coded
in the core files.
WoL on Magic Frame can be enabled by using
the ethtool support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use one memset() to reset all TDES01 fields instead
of one by one to reduce number of instructions.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a limit when perform the DMA reset procedure
so, in case of problems (i.e. PHY reset failed) the
Kernel won't hang on the stmmac DMA initialisation
blocking the Kernels execution.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first version of the driver had hard-coded the logic
for handling the checksum offloading.
This was designed according to the chips included in
the STM platforms where:
o MAC10/100 supports no COE at all.
o GMAC fully supports RX/TX COE.
This is not good for other chip configurations where,
for example, the mac10/100 supports the tx csum in HW
or when the GMAC has no IPC.
Thanks to Johannes Stezenbach; he provided me a first
draft of this patch that only reviewed the IPC for the
GMAC devices.
This patch also helps on SPEAr platforms where the
MAC10/100 can perform the TX csum in HW.
Thanks to Deepak SIKRI for his support on this.
In the end, GMAC devices for STM platforms have
a bugged Jumbo frame support that needs to have
the Tx COE disabled for oversized frames (due to
limited buffer sizes). This information is also
passed through the driver's platform structure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Deepak SIKRI <deepak.sikri@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the CSR Clock range selection.
Original patch from Johannes Stezenbach fixed the CSR
in the stmmac_mdio. We agreed to provide this through
the platform instead of.
Also thanks to Johannes for having tested it on ARM.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We cannot use spinlock when kmalloc is invoked with
GFP_KERNEL flag because it can sleep.
So this patch reviews the usage of spinlock within the
stmmac_resume function avoing this bug.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/stmmac/dwmac100_core.c: In function 'dwmac100_dump_mac_regs':
drivers/net/stmmac/dwmac100_core.c:47: warning: cast from pointer to integer of different size
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In file included from drivers/net/stmmac/stmmac_ethtool.c:30:
drivers/net/stmmac/stmmac.h:111: warning: 'struct platform_device' declared inside parameter list
drivers/net/stmmac/stmmac.h:111: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/net/stmmac/stmmac_main.c: In function 'stmmac_dvr_probe':
drivers/net/stmmac/stmmac_main.c:1744: warning: cast from pointer to integer of different size
In file included from drivers/net/stmmac/stmmac_mdio.c:31:
drivers/net/stmmac/stmmac.h:111: warning: 'struct platform_device' declared inside parameter list
drivers/net/stmmac/stmmac.h:111: warning: its scope is only this definition or declaration, which is probably not what you want
drivers/net/stmmac/dwmac1000_core.c: In function 'dwmac1000_dump_regs':
drivers/net/stmmac/dwmac1000_core.c:56: warning: cast from pointer to integer of different size
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids unnecessary casting and adds the ioaddr in the
private structure.
This patch also removes many warning when compile the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the CPU_SUBTYPE_ST40 dependency in the
driver's Kconfig.
In fact, this option has been removed in the commit:
f966918724
as reported by Christian Dietrich.
Note that the driver remains tested on STM platforms, only.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the stmmac_adjust_link() function so the
fix_mac_speed() is called not only when link speed is changing
between 10 and 100 Mbps (as required in RMII mode) but also
for 1000 Mbps.
Signed-off-by: Pawel Moll <pawel.moll@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For Simple Ethernet frames (802.2 and 802.3) the GMAC Core
never strips pad and fcs. This means the ACS has no effect
on IPv4/6 frames.
The FL bits, in the RDES0, include the FCS so the driver
has to remove it in SW.
For 802.3 frame format with LLC or LLC-SNAP, when set the ACS
bit, the HW strips both PAD and FCS.
The FL bits, in the RDES0, actually represents the frame length
already stripped.
This patch fixes this logic within the device driver that
erroneously removed 4byte from 802.3 frames already stripped
corrupting the payload.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver erroneously sets the tmrate to zero when the
TMU initialisation fails. This actually generates problems
while using the dual GMAC configuration.
With this patch, enabling both the dual gmac and the timer
optimisation, the first interface opened will use the tmu
channel 2, the second one won't be able to use the timer but
will continue to work without mitigating the interrupts by
using the external timer (i.e. TMU channel 2).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
