The clock drivers on imx8m series are registered as platform devices and
this opens the possibility of reloading the driver at runtime.
This doesn't actually work: clocks are never removed and attempting to
bind again results in registration errors and a crash. Almost all
devices depend on clocks anyway so rebinding is unlikely to ever be
useful
Fix this by explicitly suppressing bind attrs like several other
clock drivers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM frequency switches are executed in firmware and can change the
configuration of the DRAM PLL outside linux. Mark these CLKs with
CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and
recalculate rates.
In current DRAM frequency tables on 8mm/8mn only the maximum frequency
uses the PLL so it's always configured in the same way. However reading
back the PLL configuration is the correct behavior and allows additional
setpoints in the future.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These clocks are only modified as part of DRAM frequency switches during
which DRAM itself is briefly inaccessible. The switch is performed with
a SMC call to by TF-A which runs from a SRAM area; upon returning to
linux several clocks bits are modified and we need to update them.
For rate bits an easy solution is to just mark with
CLK_GET_RATE_NOCACHE so that new rates are always read back from
registers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
then a bunch of driver updates and a handful of new drivers. In terms of
diffstat the Qualcomm and Amlogic drivers are high up there because of all the
clk data introcued by new drivers. The Nvidia Tegra driver had a lot of work
done this cycle too to support suspend/resume and memory controllers. And the
OMAP clk driver got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data, mark things
static, correct incorrect data in drivers, etc. All the little things that
improve drivers and maintain code health. I will point out that there's a patch
in here for the GPIO clk driver, that almost nobody uses, which changes
behavior and causes clk_set_rate() to try to change the GPIO gate clk's parent.
Other than that things are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8 SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system suspend/resume cycle
on exynos542x SoCs
-----BEGIN PGP SIGNATURE-----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=qJNg
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
During cpu frequency switching the main "CLK_ARM" is reparented to an
intermediate "step" clock. On imx8mm and imx8mn the 24M oscillator is
used for this purpose but it is extremely slow, increasing wakeup
latencies to the point that i2c transactions can timeout and system
becomes unresponsive.
Fix by switching the "step" clk to SYS_PLL1_800M, matching the behavior
of imx8m cpufreq drivers in imx vendor tree.
This bug was not immediately apparent because upstream arm64 defconfig
uses the "performance" governor by default so no cpufreq transitions
happen.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Fixes: 96d6392b54 ("clk: imx: Add support for i.MX8MN clock driver")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lkml.kernel.org/r/f5d2b9c53f1ed5ccb1dd3c6624f56759d92e1689.1571771777.git.leonard.crestez@nxp.com
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According Architecture definition guide, SYS_PLL1 is fixed at
800MHz, SYS_PLL2 is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mm there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate. Only one of these gates (the one "dividing" by
one) is currently defined and it's incorrectly set as the parent of all
the fixed-factor dividers.
Add the other 8 gates to the clock tree between sys_pll1/2_bypass and
the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many i.MX8M SoCs use same 1443X/1416X PLL, such as i.MX8MM,
i.MX8MN and later i.MX8M SoCs, moving these PLL definitions
to pll14xx driver can save a lot of duplicated code on each
platform.
Meanwhile, no need to define PLL clock structure for every
module which uses same type of PLL, e.g., audio/video/dram use
1443X PLL, arm/gpu/vpu/sys use 1416X PLL, define 2 PLL clock
structure for each group is enough.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pll BYPASS bit should be kept inside pll driver for glitchless freq
setting following spec. If exposing the bit, that means pll driver and
clk driver has two paths to touch this bit, which is wrong.
So use EXT_BYPASS bit here.
And drop uneeded set parent, because EXT_BYPASS default is 0.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Suggested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-4-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
* There is no video_pll2 on imx8mm, replace with dummy
* Replace reference to sys_pll3_clk with sys_pll3_out
* qspi parent[2] is sys_pll2_333m not sys_pll1_800m
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no strong reason for this to use CLK_OF_DECLARE instead
of being a platform driver. Plus, this will now be aligned with the
other i.MX8M clock drivers which are platform drivers.
In order to make the clock provider a platform driver
all the data and code needs to be outside of .init section.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The AUDIO PLL max support 650M, so the original clk settings violate
spec. This patch makes the output 786432000 -> 393216000,
and 722534400 -> 361267200 to aligned with NXP vendor kernel without any
impact on audio functionality and go within 650MHz PLL limit.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has no sys3_pll2_out clock, PWM3 clock's mux option #4
should be sys_pll3_out, sys3_pll2_out is a typo, fix it.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Rename 'share_count_dcss' to 'share_count_disp', since the
DCSS module does not exist on imx8mm platform. So rename it
to avoid any unnecessary confusion.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mm datasheet of CCM, the parent of usb1_ctrl_root_clk
should be usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1416X/1443X PLL are used on i.MX8MM and i.MX8MN and maybe
other i.MX8M series SoC later, the macro definitions of
these PLLs' initialization should be common for usage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
There is no audio_pll2_clk registered, it should be audio_pll2_out.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is used for dram operations inside TF-A and must be kept
enabled for features such as suspend/resume dram retention and busfreq
to work.
This is required for imx8mm suspend to work with NXP branch of TF-A.
There is an equivalent clk on imx8mq and it's always been marked as
critical in upstream.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is documented in the reference manuals as GIC_CLK_ROOT.
In some out-of-tree DVFS scenarios the gic clock can end up as the only
user of sys_pll2 so if we don't define the gic clk explicitly it might
be turned off.
This applies to both 8mq and 8mm: same clk register but diffferent
parents.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MM has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To Frac pll, the gate shift is 13, however to Int PLL the gate shift
is 11.
Cc: <stable@vger.kernel.org>
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX8MM has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It calls another __init marked function and thus causes a section
mismatch if we don't mark it this way.
Fixes: ba5625c3e2 ("clk: imx: Add clock driver support for imx8mm")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
