Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"It looks like a sizeble collection but this is nearly 3 weeks of bug
fixing while you were away.
1) Fix crashes over IPSEC tunnels with NAT, the latter can reroute
the packet through a non-IPSEC protected path and the code has to
be able to handle SKBs attached to routes lacking an attached xfrm
state. From Steffen Klassert.
2) Fix OOPSs in ipv4 and ipv6 ipsec layers for unsupported
sub-protocols, also from Steffen Klassert.
3) Set local_df on fragmented netfilter skbs otherwise we won't be
able to forward successfully, from Florian Westphal.
4) cdc_mbim ipv6 neighbour code does __vlan_find_dev_deep without
holding RCU lock, from Bjorn Mork.
5) local_df test in ip_may_fragment is inverted, from Florian
Westphal.
6) jme driver doesn't check for DMA mapping failures, from Neil
Horman.
7) qlogic driver doesn't calculate number of TX queues properly, from
Shahed Shaikh.
8) fib_info_cnt can drift irreversibly positive if we fail to
allocate the fi->fib_metrics array, from Sergey Popovich.
9) Fix use after free in ip6_route_me_harder(), also from Sergey
Popovich.
10) When SYSCTL is disabled, we don't handle local_port_range and
ping_group_range defaults properly at all, from Cong Wang.
11) Unaccelerated VLAN tagged frames improperly handled by cdc_mbim
driver, fix from Bjorn Mork.
12) cassini driver needs nested lock annotations for TX locking, from
Emil Goode.
13) On init error ipv6 VTI driver can unregister pernet ops twice,
oops. Fix from Mahtias Krause.
14) If macvlan device is down, don't propagate IFF_ALLMULTI changes,
from Peter Christensen.
15) Missing NULL pointer check while parsing netlink config options in
ip6_tnl_validate(). From Susant Sahani.
16) Fix handling of neighbour entries during ipv6 router reachability
probing, from Duan Jiong.
17) x86 and s390 JIT address randomization has some address
calculation bugs leading to crashes, from Alexei Starovoitov and
Heiko Carstens.
18) Clear up those uglies with nop patching and net_get_random_once(),
from Hannes Frederic Sowa.
19) Option length miscalculated in ip6_append_data(), fix also from
Hannes Frederic Sowa.
20) A while ago we fixed a race during device unregistry when a
namespace went down, turns out there is a second place that needs
similar protection. From Cong Wang.
21) In the new Altera TSE driver multicast filtering isn't working,
disable it and just use promisc mode until the cause is found.
From Vince Bridgers.
22) When we disable router enabling in ipv6 we have to flush the
cached routes explicitly, from Duan Jiong.
23) NBMA tunnels should not cache routes on the tunnel object because
the key is variable, from Timo Teräs.
24) With stacked devices GRO information in skb->cb[] can be not setup
properly, make sure it is in all code paths. From Eric Dumazet.
25) Really fix stacked vlan locking, multiple levels of nesting with
intervening non-vlan devices are possible. From Vlad Yasevich.
26) Fallback ipip tunnel device's mtu is not setup properly, from
Steffen Klassert.
27) The packet scheduler's tcindex filter can crash because we
structure copy objects with list_head's inside, oops. From Cong
Wang.
28) Fix CHECKSUM_COMPLETE handling for ipv6 GRE tunnels, from Eric
Dumazet.
29) In some configurations 'itag' in __mkroute_input() can end up
being used uninitialized because of how fib_validate_source()
works. Fix it by explitly initializing itag to zero like all the
other fib_validate_source() callers do, from Li RongQing"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
batman: fix a bogus warning from batadv_is_on_batman_iface()
ipv4: initialise the itag variable in __mkroute_input
bonding: Send ALB learning packets using the right source
bonding: Don't assume 802.1Q when sending alb learning packets.
net: doc: Update references to skb->rxhash
stmmac: Remove unbalanced clk_disable call
ipv6: gro: fix CHECKSUM_COMPLETE support
net_sched: fix an oops in tcindex filter
can: peak_pci: prevent use after free at netdev removal
ip_tunnel: Initialize the fallback device properly
vlan: Fix build error wth vlan_get_encap_level()
can: c_can: remove obsolete STRICT_FRAME_ORDERING Kconfig option
MAINTAINERS: Pravin Shelar is Open vSwitch maintainer.
bnx2x: Convert return 0 to return rc
bonding: Fix alb mode to only use first level vlans.
bonding: Fix stacked device detection in arp monitoring
macvlan: Fix lockdep warnings with stacked macvlan devices
vlan: Fix lockdep warning with stacked vlan devices.
net: Allow for more then a single subclass for netif_addr_lock
net: Find the nesting level of a given device by type.
...
Pull scsi target fixes from Nicholas Bellinger:
"This series include:
- Close race between iser-target network portal shutdown + accepting
new connection logins (sagi)
- Fix free-after-use regression in tcm_fc post conversion to
percpu-ida pre-allocation (nab)
- Explicitly disable Immediate + Unsolicited Data for iser-target
connections when T10-PI is enabled (sagi + nab)
- Allow pi_prot_type + emulate_write_cache attributes to be set to
zero regardless of backend support (andy)
- memory leak fix (mikulas)"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: fix memory leak on XCOPY
target: Don't allow setting WC emulation if device doesn't support
iscsi-target: Disable Immediate + Unsolicited Data with ISER Protection
tcm_fc: Fix free-after-use regression in ft_free_cmd
iscsi-target: Change BUG_ON to REJECT in iscsit_process_nop_out
Target/iscsi,iser: Avoid accepting transport connections during stop stage
Target/iser: Fix iscsit_accept_np and rdma_cm racy flow
Target/iser: Fix wrong connection requests list addition
target: Allow non-supporting backends to set pi_prot_type to 0
When we receive a netdev event indicating a netdev change and/or
a netdev address change, we must change the MAC index used by the
proxy QP1 (in the QP context), otherwise RoCE CM packets sent by the
VF will not carry the same source MAC address as the non-CM packets.
We use the UPDATE_QP command to perform this change.
In order to avoid modifying a QP context based on netdev event,
while the driver attempts to destroy this QP (e.g either the mlx4_ib
or ib_mad modules are unloaded), we use mutex locking in both flows.
Since the relevant mlx4 proxy GSI QP is created indirectly by the
mad module when they create their GSI QP, the mlx4 didn't need to
keep track on that QP prior to this change.
Now, when QP modifications are needed to this QP from within the
driver, we added refernece to it.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the target is in stop stage, iSER transport initiates RDMA disconnects.
The iSER initiator may wish to establish a new connection over the
still existing network portal. In this case iSER transport should not
accept and resume new RDMA connections. In order to learn that, iscsi_np
is added with enabled flag so the iSER transport can check when deciding
weather to accept and resume a new connection request.
The iscsi_np is enabled after successful transport setup, and disabled
before iscsi_np login threads are cleaned up.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
RDMA CM and iSCSI target flows are asynchronous and completely
uncorrelated. Relying on the fact that iscsi_accept_np will be called
after CM connection request event and will wait for it is a mistake.
When attempting to login to a few targets this flow is racy and
unpredictable, but for parallel login to dozens of targets will
race and hang every time.
The correct synchronizing mechanism in this case is pending on
a semaphore rather than a wait_for_event. We keep the pending
interruptible for iscsi_np cleanup stage.
(Squash patch to remove dead code into parent - nab)
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Should be adding list_add_tail($new, $head) and not
the other way around.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The whole db drop avoidance stuff is for T4 only. So we cannot allow
that to be enabled for T5 devices.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This is required to work around a T5 HW issue.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In cases where the cm calls c4iw_modify_rc_qp() with the endpoint
mutex held, they must be called with internal == 1. rx_data() and
process_mpa_reply() are not doing this. This causes a deadlock
because c4iw_modify_rc_qp() might call c4iw_ep_disconnect() in some
!internal cases, and c4iw_ep_disconnect() acquires the endpoint mutex.
The design was intended to only do the disconnect for !internal calls.
Change rx_data(), FPDU_MODE case, to call c4iw_modify_rc_qp() with
internal == 1, and then disconnect only after releasing the mutex.
Change process_mpa_reply() to call c4iw_modify_rc_qp(TERMINATE) with
internal == 1 and set a new attr flag telling it to send a TERMINATE
message. Previously this was implied by !internal.
Change process_mpa_reply() to return whether the caller should
disconnect after releasing the endpoint mutex. Now rx_data() will do
the disconnect in the cases where process_mpa_reply() wants to
disconnect after the TERMINATE is sent.
Change c4iw_modify_rc_qp() RTS->TERM to only disconnect if !internal,
and to send a TERMINATE message if attrs->send_term is 1.
Change abort_connection() to not aquire the ep mutex for setting the
state, and make all calls to abort_connection() do so with the mutex
held.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
- Mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree.
- Drop deprecated MSI-X API use.
- A couple other miscellaneous things.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/PTZ
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- mostly cxgb4 fixes unblocked by the merge of some prerequisites via
the net tree
- drop deprecated MSI-X API use.
- a couple other miscellaneous things.
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cxgb4: Fix over-dereference when terminating
RDMA/cxgb4: Use uninitialized_var()
RDMA/cxgb4: Add missing debug stats
RDMA/cxgb4: Initialize reserved fields in a FW work request
RDMA/cxgb4: Use pr_warn_ratelimited
RDMA/cxgb4: Max fastreg depth depends on DSGL support
RDMA/cxgb4: SQ flush fix
RDMA/cxgb4: rmb() after reading valid gen bit
RDMA/cxgb4: Endpoint timeout fixes
RDMA/cxgb4: Use the BAR2/WC path for kernel QPs and T5 devices
IB/mlx5: Add block multicast loopback support
IB/mthca: Use pci_enable_msix_exact() instead of pci_enable_msix()
IB/qib: Use pci_enable_msix_range() instead of pci_enable_msix()
Pull SCSI target updates from Nicholas Bellinger:
"Here are the target pending updates for v3.15-rc1. Apologies in
advance for waiting until the second to last day of the merge window
to send these out.
The highlights this round include:
- iser-target support for T10 PI (DIF) offloads (Sagi + Or)
- Fix Task Aborted Status (TAS) handling in target-core (Alex Leung)
- Pass in transport supported PI at session initialization (Sagi + MKP + nab)
- Add WRITE_INSERT + READ_STRIP T10 PI support in target-core (nab + Sagi)
- Fix iscsi-target ERL=2 ASYNC_EVENT connection pointer bug (nab)
- Fix tcm_fc use-after-free of ft_tpg (Andy Grover)
- Use correct ib_sg_dma primitives in ib_isert (Mike Marciniszyn)
Also, note the virtio-scsi + vhost-scsi changes to expose T10 PI
metadata into KVM guest have been left-out for now, as there where a
few comments from MST + Paolo that where not able to be addressed in
time for v3.15. Please expect this feature for v3.16-rc1"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (43 commits)
ib_srpt: Use correct ib_sg_dma primitives
target/tcm_fc: Rename ft_tport_create to ft_tport_get
target/tcm_fc: Rename ft_{add,del}_lport to {add,del}_wwn
target/tcm_fc: Rename structs and list members for clarity
target/tcm_fc: Limit to 1 TPG per wwn
target/tcm_fc: Don't export ft_lport_list
target/tcm_fc: Fix use-after-free of ft_tpg
target: Add check to prevent Abort Task from aborting itself
target: Enable READ_STRIP emulation in target_complete_ok_work
target/sbc: Add sbc_dif_read_strip software emulation
target: Enable WRITE_INSERT emulation in target_execute_cmd
target/sbc: Add sbc_dif_generate software emulation
target/sbc: Only expose PI read_cap16 bits when supported by fabric
target/spc: Only expose PI mode page bits when supported by fabric
target/spc: Only expose PI inquiry bits when supported by fabric
target: Pass in transport supported PI at session initialization
target/iblock: Fix double bioset_integrity_free bug
Target/sbc: Initialize COMPARE_AND_WRITE write_sg scatterlist
target/rd: T10-Dif: RAM disk is allocating more space than required.
iscsi-target: Fix ERL=2 ASYNC_EVENT connection pointer bug
...
The code was incorrectly using sg_dma_address() and
sg_dma_len() instead of ib_sg_dma_address() and
ib_sg_dma_len().
This prevents srpt from functioning with the
Intel HCA and indeed will corrupt memory
badly.
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Tested-by: Vinod Kumar <vinod.kumar@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Cc: stable@vger.kernel.org # 3.3+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Need to get the endpoint reference before calling rdma_fini(), which
might fail causing us to not get the reference.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The max depth of a fastreg mr depends on whether the device supports
DSGL or not. So compute it dynamically based on the device support
and the module use_dsgl option.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
There is a race when moving a QP from RTS->CLOSING where a SQ work
request could be posted after the FW receives the RDMA_RI/FINI WR.
The SQ work request will never get processed, and should be completed
with FLUSHED status. Function c4iw_flush_sq(), however was dropping
the oldest SQ work request when in CLOSING or IDLE states, instead of
completing the pending work request. If that oldest pending work
request was actually complete and has a CQE in the CQ, then when that
CQE is proceessed in poll_cq, we'll BUG_ON() due to the inconsistent
SQ/CQ state.
This is a very small timing hole and has only been hit once so far.
The fix is two-fold:
1) c4iw_flush_sq() MUST always flush all non-completed WRs with FLUSHED
status regardless of the QP state.
2) In c4iw_modify_rc_qp(), always set the "in error" bit on the queue
before moving the state out of RTS. This ensures that the state
transition will not happen while another thread is in
post_rc_send(), because set_state() and post_rc_send() both aquire
the qp spinlock. Also, once we transition the state out of RTS,
subsequent calls to post_rc_send() will fail because the "in error"
bit is set. I don't think this fully closes the race where the FW
can get a FINI followed a SQ work request being posted (because
they are posted to differente EQs), but the #1 fix will handle the
issue by flushing the SQ work request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Some HW platforms can reorder read operations, so we must rmb() after
we see a valid gen bit in a CQE but before we read any other fields
from the CQE.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
1) timedout endpoint processing can be starved. If there are continual
CPL messages flowing into the driver, the endpoint timeout
processing can be starved. This condition exposed the other bugs
below.
Solution: In process_work(), call process_timedout_eps() after each CPL
is processed.
2) Connection events can be processed even though the endpoint is on
the timeout list. If the endpoint is scheduled for timeout
processing, then we must ignore MPA Start Requests and Replies.
Solution: Change stop_ep_timer() to return 1 if the ep has already been
queued for timeout processing. All the callers of stop_ep_timer() need
to check this and act accordingly. There are just a few cases where
the caller needs to do something different if stop_ep_timer() returns 1:
1) in process_mpa_reply(), ignore the reply and process_timeout()
will abort the connection.
2) in process_mpa_request, ignore the request and process_timeout()
will abort the connection.
It is ok for callers of stop_ep_timer() to abort the connection since
that will leave the state in ABORTING or DEAD, and process_timeout()
now ignores timeouts when the ep is in these states.
3) Double insertion on the timeout list. Since the endpoint timers
are used for connection setup and teardown, we need to guard
against the possibility that an endpoint is already on the timeout
list. This is a rare condition and only seen under heavy load and
in the presense of the above 2 bugs.
Solution: In ep_timeout(), don't queue the endpoint if it is already on
the queue.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
[ Fix cast from u64* to integer. - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Add support for the block multicast loopback QP creation flag along
the proper firmware API for that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As result of the deprecation of the MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block(), all drivers using these
two interfaces need to be updated to use the new
pci_enable_msi_range() or pci_enable_msi_exact() and
pci_enable_msix_range() or pci_enable_msix_exact() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
As result of the deprecation of the MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block(), all drivers using these
two interfaces need to be updated to use the new pci_enable_msi_range()
and pci_enable_msix_range() interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In order to support local WRITE_INSERT + READ_STRIP operations for
non PI enabled fabrics, the fabric driver needs to be able signal
what protection offload operations are supported.
This is done at session initialization time so the modes can be
signaled by individual se_wwn + se_portal_group endpoints, as well
as optionally across different transports on the same endpoint.
For iser-target, set TARGET_PROT_ALL if the underlying ib_device
has already signaled PI offload support, and allow this to be
exposed via a new iscsit_transport->iscsit_get_sup_prot_ops()
callback.
For loopback, set TARGET_PROT_ALL to signal SCSI initiator mode
operation.
For all other drivers, set TARGET_PROT_NORMAL to disable fabric
level PI.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fastreg is mandatory for signature, so if the
device doesn't support it we don't need to use it.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a bug where outstanding RDMA_READs with WRITE_PENDING
status require an extra target_put_sess_cmd() in isert_put_cmd() code
when called from isert_cq_tx_comp_err() + isert_cq_drain_comp_llist()
context during session shutdown.
The extra kref PUT is required so that transport_generic_free_cmd()
invokes the last target_put_sess_cmd() -> target_release_cmd_kref(),
which will complete(&se_cmd->cmd_wait_comp) the outstanding se_cmd
descriptor with WRITE_PENDING status, and awake the completion in
target_wait_for_sess_cmds() to invoke TFO->release_cmd().
The bug was manifesting itself in target_wait_for_sess_cmds() where
a se_cmd descriptor with WRITE_PENDING status would end up sleeping
indefinately.
Acked-by: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Now that TASK_ABORTED status is not generated for all cases by
TMR ABORT_TASK + LUN_RESET, a new TFO->abort_task() caller is
necessary in order to give fabric drivers a chance to unmap
hardware / software resources before the se_cmd descriptor is
released via the normal TFO->release_cmd() codepath.
This patch adds TFO->aborted_task() in core_tmr_abort_task()
in place of the original transport_send_task_abort(), and
also updates all fabric drivers to implement this caller.
The fabric drivers that include changes to perform cleanup
via ->aborted_task() are:
- iscsi-target
- iser-target
- srpt
- tcm_qla2xxx
The fabric drivers that currently set ->aborted_task() to
NOPs are:
- loopback
- tcm_fc
- usb-gadget
- sbp-target
- vhost-scsi
For the latter five, there appears to be no additional cleanup
required before invoking TFO->release_cmd() to release the
se_cmd descriptor.
v2 changes:
- Move ->aborted_task() call into transport_cmd_finish_abort (Alex)
Cc: Alex Leung <amleung21@yahoo.com>
Cc: Mark Rustad <mark.d.rustad@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Cc: Vu Pham <vu@mellanox.com>
Cc: Chris Boot <bootc@bootc.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes isert_conn_create_fastreg_pool() to follow
logic in iscsi_target_locate_portal() for determining how many
FRMR descriptors to allocate based upon the number of possible
per-session command slots that are available.
This addresses an OOPs in isert_reg_rdma() where due to the
use of ISCSI_DEF_XMIT_CMDS_MAX could end up returning a bogus
fast_reg_descriptor when the number of active tags exceeded
the original hardcoded max.
Note this also includes moving isert_conn_create_fastreg_pool()
from isert_connect_request() to isert_put_login_tx() before
posting the final Login Response PDU in order to determine the
se_nacl->queue_depth (eg: number of tags) per session the target
will be enforcing.
v2 changes:
- Move isert_conn->conn_fr_pool list_head init into
isert_conn_request()
v3 changes:
- Drop unnecessary list_empty() check in isert_reg_rdma()
(Sagi)
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org> #3.12+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If during data-transfer a data-integrity error was detected we
must fail the command with CHECK_CONDITION and not execute
the command.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove code duplication from RDMA_READ and RDMA_WRITE
completions that do basically the same check.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If protection is involved, iSER target must wait for
completion of RDMA_READ before sending SCSI response.
So we must consider that when calculating post_send_buf_count
additions, also when processing good/error completions.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
As REG_SIG_MR work request and it's LOCAL_INVALIDATE are
not accounted in post_send_buf_count we must color these
with ISER_FASTREG_LI_WRID in order to process their error
completions when the QP flushes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the Target core passed transport T10 protection
operation:
1. Register data buffer (data memory region)
2. Register protection buffer if exsists (prot memory region)
3. Register signature region (signature memory region)
- use work request IB_WR_REG_SIG_MR
4. Execute RDMA
5. Upon RDMA completion check the signature status
- if succeeded send good SCSI response
- if failed send SCSI bad response with appropriate sense buffer
(Fix up compile error in isert_reg_sig_mr, and fix up incorrect
se_cmd->prot_type -> TARGET_PROT_NORMAL comparision - nab)
(Fix failed sector assignment in isert_completion_rdma_* - Sagi + nab)
(Fix enum assignements for protection type - Sagi)
(Fix devision on 32-bit in isert_completion_rdma_* - Sagi + Fengguang)
(Fix context change for v3.14-rc6 code - nab)
(Fix iscsit_build_rsp_pdu inc_statsn flag usage - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case of protected transactions, we will need to check the
protection status of the transaction before sending SCSI response.
So be ready for RDMA_WRITE completions. currently we don't ask
for these completions, but for T10-PI we will.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Introduce pi_context to hold relevant RDMA protection resources.
We eliminate data_key_valid boolean and replace it with indicators
container to indicate:
- Is the descriptor protected (registered via signature MR)
- Is the data_mr key valid (can spare LOCAL_INV WR)
- Is the prot_mr key valid (can spare LOCAL_INV WR)
- Is the sig_mr key valid (can spare LOCAL_INV WR)
Upon connection establishment check if network portal is T10-PI
enabled and allocate T10-PI resources if necessary, allocate
signature enabled memory regions and mark connection queue-pair
as signature enabled.
(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
export map/unmap data buffer to a routine that may
be used in various places in the code and keep the
mapping data in a designated descriptor. Also, let
isert_fast_reg_mr to decide weather to use global
MR or do fast registration.
This commit does not change any functionality.
(Fix context change for v3.14-rc6 code - nab)
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will be
arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath and
ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc. from
intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ww6H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.15:
- The biggest change is core API extensions and mlx5 low-level driver
support for handling DIF/DIX-style protection information, and the
addition of PI support to the iSER initiator. Target support will
be arriving shortly through the SCSI target tree.
- A nice simplification to the "umem" memory pinning library now that
we have chained sg lists. Kudos to Yishai Hadas for realizing our
code didn't have to be so crazy.
- Another nice simplification to the sg wrappers used by qib, ipath
and ehca to handle their mapping of memory to adapter.
- The usual batch of fixes to bugs found by static checkers etc.
from intrepid people like Dan Carpenter and Yann Droneaud.
- A large batch of cxgb4, ocrdma, qib driver updates"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (102 commits)
RDMA/ocrdma: Unregister inet notifier when unloading ocrdma
RDMA/ocrdma: Fix warnings about pointer <-> integer casts
RDMA/ocrdma: Code clean-up
RDMA/ocrdma: Display FW version
RDMA/ocrdma: Query controller information
RDMA/ocrdma: Support non-embedded mailbox commands
RDMA/ocrdma: Handle CQ overrun error
RDMA/ocrdma: Display proper value for max_mw
RDMA/ocrdma: Use non-zero tag in SRQ posting
RDMA/ocrdma: Memory leak fix in ocrdma_dereg_mr()
RDMA/ocrdma: Increment abi version count
RDMA/ocrdma: Update version string
be2net: Add abi version between be2net and ocrdma
RDMA/ocrdma: ABI versioning between ocrdma and be2net
RDMA/ocrdma: Allow DPP QP creation
RDMA/ocrdma: Read ASIC_ID register to select asic_gen
RDMA/ocrdma: SQ and RQ doorbell offset clean up
RDMA/ocrdma: EQ full catastrophe avoidance
RDMA/cxgb4: Disable DSGL use by default
RDMA/cxgb4: rx_data() needs to hold the ep mutex
...
Unregister the inet notifier during ocrdma unload to avoid a panic after
driver unload.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Clean up code. Also modifying GSI QP to error during ocrdma_close is fixed.
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Issue mailbox commands to query ocrdma controller information and phy
information and print them while adding ocrdma device.
Signed-off-by: Selvin Xavier <selvin.xavier@emulex.com>
Signed-off-by: Devesh Sharma <devesh.sharma@emulex.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
