2
0
mirror of https://github.com/edk2-porting/linux-next.git synced 2025-01-12 23:54:19 +08:00
Commit Graph

3508 Commits

Author SHA1 Message Date
Kuninori Morimoto
e85dd04ea8 mmc: tmio: remove Renesas specific #ifdef
This patch adds new TMIO_MMC_HAVE_CTL_DMA_REG flag,
and remove Renesas specific #ifdef from tmio driver

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:15 +02:00
Shinobu Uehara
81e888daab mmc: tmio: check ILL_FUNC instead of CBSY
Some controllers need to check SD bus status when writing data.
Then, it checks ILL_FUNC bit on SD_INFO2 register,
and this method is controlled via TMIO_MMC_HAS_IDLE_WAIT flags.
Same method is required on tmio_mmc_data_irq() which will
be called after writing data.

Current driver is checking CBSY bit for this purpose,
but, some controllers doesn't have CBSY bit.
This patch checks ILL_FUNC bit instead of CBSY bit
if it has TMIO_MMC_HAS_IDLE_WAIT flags

[Kuninori Morimoto: tidyuped for upstreaming]

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:15 +02:00
Shinobu Uehara
6b98757e53 mmc: tmio: add TMIO_MMC_SDIO_STATUS_QUIRK
Renesas R-Car SDHI should set reserved bits
on CTL_SDIO_STATUS register when writing.
This patch adds new TMIO_MMC_SDIO_STATUS_QUIRK flags
for this purpose

[Kuninori Morimoto: tidyuped for upstreaming
                    enabled this flags for all SH-Mobile/R-Car]

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:14 +02:00
Shinobu Uehara
b8d11962c2 mmc: tmio: control multiple block transfer mode
Renesas SDHI has "Multiple Block Transfer Mode" settings
on SD_CMD register which controls CMD12 automatically.

This patch cares it, because
CMD12 is not needed when CMD53 (= SD_IO_RW_EXTENDED)

[Kuninori Morimoto: tidyuped for upstreaming
                    enabled this flags for all SH-Mobile/R-Car]

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:14 +02:00
Shinobu Uehara
f83bfa751b mmc: tmio: clear error IRQ status
Next card access will be always
error if it didn't clear error status

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Shinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:13 +02:00
Kuninori Morimoto
384b2cbd56 mmc: tmio: care about DMA tx/rx addr offset
Basically, SD_BUF0 Tx/Rx addresses are same
in normal TMIO controller,
but, it is different on Renesas R-Car SDHI controller
if it uses DMAC
(Rx address needs to add 0x2000 to Tx address)

This patch adds new .dma_rx_offset and cares it

Tested-by: Nguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:13 +02:00
Ulf Hansson
341eb6a4e7 mmc: tmio: Remove library functions for system PM
These library functions aren't used and nor needed, let's remove them.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:12 +02:00
Ulf Hansson
70a15e1a3c mmc: tmio_mmc: Fixup system PM suspend lock-up
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.

The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.

In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:12 +02:00
Ulf Hansson
753a688c9f mmc: sdhi: Fixup system PM suspend lock-up
At system PM suspend, the tmio core accessed the internal registers of
the controller without first moving the device into active state. This
caused a lock-up in system PM suspend phase.

The reason for the register access were masking of IRQs. Since that is
managed via the runtime PM suspend path, let's just re-use that path
for system PM suspend.

In other words force the device into runtime PM suspend state at system
PM suspend and restore it to active state at system PM resume.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:12 +02:00
Ulf Hansson
78f76df609 mmc: tmio_mmc: Enable runtime PM support
To take advantage of the clock gating support, use the runtime PM
callbacks provided by the tmio core.

Additionally, we make use of the SET_PM_RUNTIME_PM_OPS, which is a
preparation needed to simplify system PM.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:11 +02:00
Ulf Hansson
f74f1e3820 mmc: sdhi: Make runtime PM callbacks available for CONFIG_PM
To be able to simplify system PM, let's re-use the runtime PM callbacks
by converting to the SET_PM_RUNTIME_PM_OPS macro.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:11 +02:00
Ulf Hansson
9ade7dbf20 mmc: tmio: Make runtime PM callbacks available for CONFIG_PM
To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:10 +02:00
Ulf Hansson
20e955c3c7 mmc: tmio: Mask all IRQs when inactive
To make sure we don't receive any spurious IRQs while we are inactive,
mask the IRQs from within the ->runtime_suspend() callback.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:10 +02:00
Ulf Hansson
ae12d25053 mmc: tmio: Handle clock gating from runtime PM functions
Add clock gating control as a part of the tmio library functions for
runtime PM.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:10 +02:00
Ulf Hansson
3b292bb0e9 mmc: tmio: Restructure ->set_ios() and adapt ->probe() to it
An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.

By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.

Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:09 +02:00
Ulf Hansson
9ae4ed7d30 mmc: tmio: Extract bus_width modifications to a separate function
Move code for bus_width modification, out of the ->set_ios() callback
and into a separate function, to simplify code.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:09 +02:00
Ulf Hansson
0369483efc mmc: tmio: Keep host active while serving requests
Use runtime PM to keep the host active during I/O operations and other
requests which requires the tmio hardware to be powered.

Additionally make use of the runtime PM autosuspend feature with a
default timeout of 50 ms.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:08 +02:00
Ulf Hansson
7501c4315f mmc: tmio: Keep host active while SDIO IRQ is enabled
The host must be kept active to be able to serve SDIO IRQs, thus let's
prevent it from going inactive while SDIO IRQ is enabled.

Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
2014-09-09 13:59:08 +02:00
Nicolas Ferre
215ba3995a mmc: atmel-mci: add 0x600 IP version
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:08 +02:00
Javier Martinez Canillas
9ed7ca89e0 mmc: core: Use regulator_get_voltage() if OCR mask is empty.
The operation conditions register (OCR) stores the voltage
profile of the card, however the list of possible voltages
is restricted by the voltage range supported by the supply
used as VCC/VDD. So in mmc_vddrange_to_ocrmask() a OCR mask
is obtained to filter the not supported voltages, from the
value read in the host controller OCR register.

For fixed regulators, regulator_list_voltage() returns the
fixed output for the first selector but this doesn't happen
for switch (FET) regulators that obtain their voltage from
their parent supply. A call to regulator_get_voltage() is
needed in this case so the regulator core can return the
FET's parent supply voltage output.

This change is consistent with the fact that for other
fixed regulators (that are not FETs) the OCR mask is
returned even when mmc_regulator_set_ocr() checks if the
regulator is fixed before calling regulator_set_voltage().

Without this patch, the following warning is reported when
a FET is used as a vmmc-supply:

dwmmc_exynos 12220000.mmc: Failed getting OCR mask: -22

Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:07 +02:00
Sascha Hauer
3d705d14fe mmc: implement Driver Stage Register handling
Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.

Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.

This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:07 +02:00
Peter Griffin
b315376573 mmc: sdhci-pxav3: set_uhs_signaling is initialized twice differently
.set_uhs_signaling field is currently initialised twice once to the
arch specific callback pxav3_set_uhs_signaling, and also to the generic
sdhci_set_uhs_signaling callback.

This means that uhs is currently broken for this platform currently, as pxav3
has some special constriants which means it can't use the generic callback.

This happened in
commit 96d7b78cfc ("mmc: sdhci: convert sdhci_set_uhs_signaling() into a library function")
commit a702c8abb2 ("mmc: host: split up sdhci-pxa, create sdhci-pxav3.c")'

Fix this and hopefully prevent it happening in the future by ensuring named
initialisers always follow the declaration order in the structure definition.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:06 +02:00
Peter Griffin
1d75f74b14 mmc: sdhci-acpi.c: Use SET_RUNTIME_PM_OPS macro to set runtime pm callbacks
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:06 +02:00
Peter Griffin
f3a92b1a32 mmc: sdhci-pci: Use SET_RUNTIME_PM_OPS macro to set runtime pm callbacks
This allows us to get rid of the #else condition, as the macro compiles
away to nothing if not enabled.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:06 +02:00
Peter Griffin
0529b81094 mmc: dw_mmc-pltfm: Remove superflous #else condition on CONFIG_PM_SLEEP
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:05 +02:00
Peter Griffin
eb4667426b mmc: dw_mmc-pci: Remove superflous #else condition on CONFIG_PM_SLEEP
As the code is using SIMPLE_DEV_PM_OPS helper, this compiles away to
nothing if CONFIG_PM_SLEEP is disabled. Thus we don't need to #define
the suspend/resume callbacks to NULL.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:05 +02:00
Peter Griffin
2137f5d3b8 mmc: remove .owner field for drivers using module_platform_driver
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:04 +02:00
Fu Zhonghui
dea67c4ec8 mmc: core: sdio: Fix unconditional wake_up_process() on sdio thread
781e989cf5 ("mmc: sdhci: convert to new SDIO IRQ handling") and
bf3b5ec66b ("mmc: sdio_irq: rework sdio irq handling") disabled
the use of our own custom threaded IRQ handler, but left in an
unconditional wake_up_process() on that handler at resume-time.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=80151

In addition, the check for MMC_CAP_SDIO_IRQ capability is added
before enable sdio IRQ.

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Signed-off-by: Fu Zhonghui <zhonghui.fu@linux.intel.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:04 +02:00
Andrew Bresticker
b1dec12032 mmc: dw_mmc: Add support for MIPS
There are upcoming MIPS SoCs with dw_mmc hosts.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:03 +02:00
Andrew Bresticker
0857c6912d mmc: dw_mmc: Add dependency on DMA
The dw_mmc drivers rely on the DMA API, so update the Kconfig entry
to depend on HAS_DMA.  Since the drivers should build on any platform
with DMA, allow the driver to compile tested on non-ARC/ARM platforms.

Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:03 +02:00
Matthieu CASTET
fac6a52fe9 sdhci : recompute timeout_clk when needed
when SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK is set, timeout_clk is sdclk.
We need to update it when we change sdclk in sdhci_set_clock.
This allow to have a more precisse timeout and max_busy_timeout. This
can help for command that need a big busy wait (erase, ...).

Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:03 +02:00
Matthieu CASTET
c5abd5e899 sdhci : handle busy timeout irq
When we wait for busy after sending a command, if there is
a timeout, we got SDHCI_INT_DATA_TIMEOUT flags.
Before this commit we got the message :
"Got data interrupt 0x00100000 even though no data  operation was in progress."
and we need to wait 10s that sdhci_timeout_timer expires.

Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:02 +02:00
Roger Tseng
6f67cc6fd1 mmc: rtsx_usb_sdmmc: fix incorrect last byte in R2 response
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.

Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.

Cc: <stable@vger.kernel.org> # v3.16+
Fixes: c7f6558d84 ("mmc: Add realtek USB sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:02 +02:00
Roger Tseng
d1419d50c1 mmc: rtsx_pci_sdmmc: fix incorrect last byte in R2 response
Current code erroneously fill the last byte of R2 response with an undefined
value. In addition, the controller actually 'offloads' the last byte
(CRC7, end bit) while receiving R2 response and thus it's impossible to get the
actual value. This could cause mmc stack to obtain inconsistent CID from the
same card after resume and misidentify it as a different card.

Fix by assigning dummy CRC and end bit: {7'b0, 1} = 0x1 to the last byte of R2.

Cc: <stable@vger.kernel.org> # v3.8+
Fixes: ff984e57d3 ("mmc: Add realtek pcie sdmmc host driver")
Signed-off-by: Roger Tseng <rogerable@realtek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:01 +02:00
Wei Yongjun
ee9d19d42c mmc: au1xmmc: fix error return code in au1xmmc_probe()
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:01 +02:00
Doug Anderson
2aa354650a mmc: dw_mmc: Make sure we don't get stuck when we get an error
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request.  That would leave the caller just hanging there.

We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:

1. Fix a race in the tasklet where the interrupt setting the data
   error happens _just after_ we check for it, then we get a
   EVENT_XFER_COMPLETE.  We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
   busy" state and we're not going to do anything else we end the
   request and unblock anyone waiting.

Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:01 +02:00
Chuanxiao.Dong
ae9060377a mmc: sdhci: fix the wrong type of curr
curr should use signed type since it will contain the returned
value which is possible to be a negative value. Using u32 will
make the returned value to be true even there is a negative result.
Change to use int instead of u32

Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:59:00 +02:00
Apelete Seketeli
bb2f45927f mmc: jz4740: prepare next dma transfer in parallel with current transfer
Make use of the MMC asynchronous request capability to prepare the
next DMA transfer request in parallel with the current transfer.
This is done by adding pre-request and post-request callbacks that are
used by the MMC framework during an active data transfer.

It should help reduce the impact of DMA preparation overhead on the SD
card performance.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:58:59 +02:00
Apelete Seketeli
7ca27a6f80 mmc: jz4740: add dma infrastructure for data transfers
Until now the MMC driver for JZ4740 SoC was relying on PIO mode only
for data transfers.
This patch allows the use of DMA for data trasnfers in addition to PIO
mode by relying on DMA Engine.

DMA tranfers performance might be further improved by taking advantage
of the asynchronous request capability of the MMC framework.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:58:59 +02:00
Addy Ke
f629ba2c04 mmc: dw_mmc: add support for RK3288
This patch focuses on clock setting for RK3288 mmc controller.

In RK3288 mmc controller, CLKDIV register can only be set 0 or 1,
and if DDR 8bit mode, CLKDIV register must be set 1.

Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:58:59 +02:00
Pawel Moll
45c19e2a81 mmc: sdhci-pltfm: Do not use parent as the host's device
The code selecting a device for the sdhci host has been
continuously tweaked (4b711cb138
"mmc: sdhci-pltfm: Add structure for host-specific data" and
a4d2177f00 "mmc: sdhci-pltfm: dt
device does not pass parent to sdhci_alloc_host" while there
does not seem to be any reason to use platform device's parent
in the first place.

The comment saying "Some PCI-based MFD need the parent here"
seem to refer to Timberdale FPGA driver (the only MFD driver
registering SDHCI cell, drivers/mfd/timberdale.c) but again,
the only situation when parent device matter is runtime PM,
which is not implemented for Timberdale.

Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:58:58 +02:00
Tim Kryger
ca6429d495 mmc: core: Remove fixed voltage regulator logic
There is no need for regulator consumers to include special logic for
fixed voltage regulators as they support regulator_set_voltage() just
like their non-fixed regulator counterparts.

Signed-off-by: Tim Kryger <tim.kryger@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:58:57 +02:00
Srinivas Kandagatla
9cb15142d0 mmc: mmci: Add qcom dml support to the driver.
On Qualcomm APQ8064 SOCs, SD card controller has an additional glue
called DML (Data Mover Local/Lite) to assist dma transfers.
This hardware needs to be setup before any dma transfer is requested.
DML itself is not a DMA engine, its just a gule between the SD card
controller and dma controller.

Most of this code has been ported from qualcomm's 3.4 kernel.

This patch adds the code necessary to intialize the hardware and setup
before doing any dma transfers.

Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-09 13:58:46 +02:00
Bartlomiej Zolnierkiewicz
221414db19 mmc: sdhci-s3c: fix runtime PM handling on sdhci_add_host() failure
Runtime Power Management handling for the sdhci_add_host() failure
case in sdhci_s3c_probe() should match the code in sdhci_s3c_remove()
(which uses pm_runtime_disable() call which matches the earlier
pm_runtime_enable() one).  Fix it.

This patch fixes "BUG: spinlock bad magic on CPU#0, swapper/0/1" and
"Unbalanced pm_runtime_enable!" warnings.

>From the kernel log:
...
[    1.659631] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[    1.665096] BUG: spinlock bad magic on CPU#0, swapper/0/1
[    1.670433]  lock: 0xea01e484, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
[    1.677895] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.16.0-next-20140804-00008-ga59480f-dirty 
[    1.687037] [<c0013ae4>] (unwind_backtrace) from [<c0010d70>] (show_stack+0x10/0x14)
[    1.694740] [<c0010d70>] (show_stack) from [<c04050c8>] (dump_stack+0x68/0xb8)
[    1.701948] [<c04050c8>] (dump_stack) from [<c0052558>] (do_raw_spin_lock+0x15c/0x1a4)
[    1.709848] [<c0052558>] (do_raw_spin_lock) from [<c040a630>] (_raw_spin_lock_irqsave+0x20/0x28)
[    1.718619] [<c040a630>] (_raw_spin_lock_irqsave) from [<c030d7d0>] (sdhci_do_set_ios+0x1c/0x5cc)
[    1.727464] [<c030d7d0>] (sdhci_do_set_ios) from [<c030ddfc>] (sdhci_runtime_resume_host+0x50/0x104)
[    1.736574] [<c030ddfc>] (sdhci_runtime_resume_host) from [<c02462dc>] (pm_generic_runtime_resume+0x2c/0x40)
[    1.746383] [<c02462dc>] (pm_generic_runtime_resume) from [<c0247898>] (__rpm_callback+0x34/0x70)
[    1.755233] [<c0247898>] (__rpm_callback) from [<c02478fc>] (rpm_callback+0x28/0x88)
[    1.762958] [<c02478fc>] (rpm_callback) from [<c02486f0>] (rpm_resume+0x384/0x4ec)
[    1.770511] [<c02486f0>] (rpm_resume) from [<c02488b0>] (pm_runtime_forbid+0x58/0x64)
[    1.778325] [<c02488b0>] (pm_runtime_forbid) from [<c030ea70>] (sdhci_s3c_probe+0x4a4/0x540)
[    1.786749] [<c030ea70>] (sdhci_s3c_probe) from [<c02429cc>] (platform_drv_probe+0x2c/0x5c)
[    1.795076] [<c02429cc>] (platform_drv_probe) from [<c02415f0>] (driver_probe_device+0x114/0x234)
[    1.803929] [<c02415f0>] (driver_probe_device) from [<c024179c>] (__driver_attach+0x8c/0x90)
[    1.812347] [<c024179c>] (__driver_attach) from [<c023ffb4>] (bus_for_each_dev+0x54/0x88)
[    1.820506] [<c023ffb4>] (bus_for_each_dev) from [<c0240df8>] (bus_add_driver+0xd8/0x1cc)
[    1.828665] [<c0240df8>] (bus_add_driver) from [<c0241db8>] (driver_register+0x78/0xf4)
[    1.836652] [<c0241db8>] (driver_register) from [<c00088a4>] (do_one_initcall+0x80/0x1d0)
[    1.844816] [<c00088a4>] (do_one_initcall) from [<c059ac94>] (kernel_init_freeable+0x108/0x1d4)
[    1.853503] [<c059ac94>] (kernel_init_freeable) from [<c0401300>] (kernel_init+0x8/0xe4)
[    1.861568] [<c0401300>] (kernel_init) from [<c000e538>] (ret_from_fork+0x14/0x3c)
[    1.869582] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...
[    1.997047] s3c-sdhci 12530000.sdhci: Unbalanced pm_runtime_enable!
...
[    2.027235] s3c-sdhci 12530000.sdhci: sdhci_add_host() failed
[    2.032884] platform 12530000.sdhci: Driver s3c-sdhci requests probe deferral
...

Tested on Hardkernel's Exynos4412 based ODROID-U3 board.

Fixes: 9f4e8151db ("mmc: sdhci-s3c: Enable runtime power management")
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-09-08 10:23:04 +02:00
Linus Torvalds
a11c5c9ef6 PCI changes for the v3.17 merge window (part 2):
Miscellaneous
     - Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT7PyAAAoJEFmIoMA60/r8kjQQALr/8oEfZoVcjgCb7waWOr25
 hUTnrI6GBIAh/50hoBiPq0ouPCAKVv66+CUhuhFkLP7oJz+rMU0B9hfUvdLfmCpH
 7ppaallkllT9nPFIr7h5RUWLXsoQyuHmCYmSrUCcnlT2LPgU0dN72YWElLisEM6Z
 Pldg3933xyIQaCWviHjGEjWb7NvC+JY4pTkV5iyqGgU8Ale/eFYtLLSfdBEjIbGv
 VDirYZmKELYeuncZPrTAsp4IENRMZn702wwDakMSODVMEWtJB5h4yrBawqQDlFP5
 9ztIX6n9p9zkdVKbYZlx/Xwv6SYEnYXLxauVQMSO3Nck7Z10R5Ud+5uuCg/6mWH8
 AQI4UV5bbJcg7zHgocTG9XLFLFPoPtD2JT6k6UT1LeUAiAOqcSzhRO+/qJBmJOWZ
 Zv+EHXPlxBrl0zNifut6ZQrY17teuItVtmha70a/9W3PjnIx3KecqLcTwdTvDsOY
 IAyH8WMZrBKpPpsczSmfE93i2Z1QRS91HEAOeSMxl/98dcDTdllYZS7spjoDll2f
 xmpGDbpriLSCu2XsGHfTC9RbqA7CyuFlHggJSQDkT/5Esli0sCs7eweTuK3RVvPu
 t6bUHK3yElb6x9qMZhb5q6l72wSMlGMishTdaxEHmqrEA8PtaIFodmVX2T/Zel5n
 GHN6bysPqDItNR2v/3JX
 =jJGu
 -----END PGP SIGNATURE-----

Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci

Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
 "Part two of the PCI changes for v3.17:

    - Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)

  It's a mechanical change that removes uses of the
  DEFINE_PCI_DEVICE_TABLE macro.  I waited until later in the merge
  window to reduce conflicts, but it's possible you'll still see a few"

* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
2014-08-14 18:10:33 -06:00
Linus Torvalds
a8e4def604 MMC core:
- Forward compatibility for eMMC.
  - Fix some blacklisted cards with broken secure discard.
 
 MMC host:
  - mmci: Add support for Qualcomm variant.
  - mmci: Fix regression for arm_variant.
  - sdhci: Various fixes and cleanups.
  - sdhci: Improve external VDD regulator support.
  - sdhci: Support for DDR50 1.8V mode for BayTrail.
  - sdhci-st: Add driver for ST SDHCI controller.
  - sh-mmcif: DMA fixes.
  - omap_hsmmc: Add support for SDIO interrupts.
  - sdhci-pci: Add support for Intel Quark X1000.
  - dw_mmc: Update the reset sequence.
  - s3cmci: port DMA code to dmaengine API.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJT6K/QAAoJEP4mhCVzWIwpj5UP/3KWAsUCz5PlPaTxWgh/U+aN
 lwO8aryFGjxfengCtJaw4cVksg3Lc5EvaSweg7BUqTucHoq/epdAU+Doqf5OVZ9Y
 kicfx+WOAwIGTTuY9Wu7W884WgF+litZW4O4LtQnr6hHzx+xQhPabTc6zKJVS7WD
 /Fx1Qcc0WFdGA3D0VdpCqGa7Y8IYk8cEP16MOA4s0HxZxONkjFbPdpQRF/zywGOA
 tqJC7kAhlY+Rx5bsrr5Lvbhu2Ut+cfLBPdPYuJz50wnymQ15IrLj5n4rSd5GLY+f
 HjMeCJzDHi1gk26wn3kYyWwz3JkJGWhtf6fC1hDqvkWEmHd872v7EuU9V4D3ehV1
 xPVVVyUYqMgs0Vi+PXAlMhoajrwgnlM1Ox0sheOOefcaRoFVpV6PZOuAsAOfKRfC
 ySOuEhOKn5OOvjH2TB4dNH1a3hegR9B3fJqjFe4UmUQP4FBicOfUKi+n6HwC+Omb
 VDCuVvwmMCVPi/Lop6thpPepJBfR8Ncb3vanLpK64LcIjEfoPTwoAyNI32Qnry52
 XMO4Tppl+bPzglGpV427KXlFbBwccp+8sCMRc/4lRiIMH9QhbZfVA1FcxwpvZ419
 6SKXmqhA62nHLcWlQrRlvdnNyr+Ow2o5gJ0iVffByfmzcgPmja9YZYyDfx+DxWOo
 W1oItq+qMd25rnnOPTLB
 =kGSY
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc

Pull MMC updates from Ulf Hansson:
 "Me and Chris Ball decided to try out using my MMC tree as the primary
  one, to simplify handling of patches.

  This pull does thus contains all the MMC patches for 3.17 rc1, no pull
  from Chris this time.

  Details:

  MMC core:
   - forward compatibility for eMMC
   - fix some blacklisted cards with broken secure discard

  MMC host:
   - mmci: Add support for Qualcomm variant
   - mmci: Fix regression for arm_variant
   - sdhci: Various fixes and cleanups
   - sdhci: Improve external VDD regulator support
   - sdhci: Support for DDR50 1.8V mode for BayTrail
   - sdhci-st: Add driver for ST SDHCI controller
   - sh-mmcif: DMA fixes
   - omap_hsmmc: Add support for SDIO interrupts
   - sdhci-pci: Add support for Intel Quark X1000
   - dw_mmc: Update the reset sequence
   - s3cmci: port DMA code to dmaengine API"

* tag 'mmc-v3.17-1' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
  mmc: dw_mmc: modify the dt-binding for removing slot-node and supports-highspeed
  mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
  mmc: mmci: Reverse IRQ handling for the arm_variant
  mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
  mmc: mmci: Remove redundant check of status for DATA irq
  mmc: dw_mmc: change to use recommended reset procedure
  mmc: sdhci-pxav3: Use devm_* managed helpers
  mmc: tmio: Configure DMA slave bus width
  mmc: sh_mmcif: Configure DMA slave bus width
  mmc: sh_mmcif: Fix DMA slave address configuration
  mmc: sh_mmcif: Document DT bindings
  mmc: sdhci-pci: remove PCI PM functions in suspend/resume callback
  mmc: Do not advertise secure discard if it is blacklisted
  mmc: sdhci-msm: Get COMPILE_TEST support
  mmc: sdhci-msm: Remove unnecessary header file inclusion
  mmc: sdhci-msm: Fix the binding example
  mmc: sdhci: add DDR50 1.8V mode support for BayTrail eMMC Controller
  mmc: sdhci: Preset value not supported in Baytrail eMMC
  mmc: MMC_USDHI6ROL0 should depend on HAS_DMA
  mmc: MMC_SH_MMCIF should depend on HAS_DMA
  ...
2014-08-14 09:15:53 -06:00
Benoit Taine
9baa3c34ac PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
2014-08-12 12:15:14 -06:00
Jaehoon Chung
26375b5c84 mmc: dw_mmc: Slot quirk "disable-wp" is deprecated.
Slot quirks "disable-wp" is deprecated.
Instead, use the host quirk "disable-wp".
(Because the slot-node is removed in dt-file.)

Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-08-11 11:42:39 +02:00
Ulf Hansson
7878289b26 mmc: mmci: Reverse IRQ handling for the arm_variant
Commit "mmc: mmci: Handle CMD irq before DATA irq", caused an issue
when using the ARM model of the PL181 and running QEMU.

The bug was reported for the following QEMU version:
$ qemu-system-arm -version
QEMU emulator version 2.0.0 (Debian 2.0.0+dfsg-2ubuntu1.1), Copyright
(c) 2003-2008 Fabrice Bellard

To resolve the problem, let's restore the old behavior were the DATA
irq is handled prior the CMD irq, but only for the arm_variant, which
the problem was reported for.

Reported-by: John Stultz <john.stultz@linaro.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-08-11 10:24:23 +02:00
Ulf Hansson
ad82bfea44 mmc: mmci: Move all CMD irq handling to mmci_cmd_irq()
This patch won't change the behavior of how mmci deals with CMD irqs.
By moving code from mmci_irq() to mmci_cmd_irq(), we getter a better
overview of what going on.

Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Kees Cook <keescook@chromium.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-08-11 10:24:15 +02:00