The following compilation issue popped up moving from v3.10-rc1 to
v3.10-rc6 after merging wireless-testing.
net/wireless/sysfs.c:86:13: error: 'cfg80211_leave_all' defined
but not used [-Werror=unused-function]
The function is only called when CONFIG_PM is enabled. Moving the
function under CONFIG_PM as well.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If it *is* still set when the netdev is being deleted,
then we are about to leak a pointer. Warn and clean up
in that case.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Should help the next person that tries to understand
the bss refcounting logic.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the potential issue that the BSS struct that we use
and later assign to wdev->current_bss is removed from the scan
list while associating.
Also warn when we don't have a BSS struct in connect_result
unless it's from a driver that only has the connect() API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Doing so will allow us to hold the BSS (not just ref it) over the
association process, thus ensuring that it doesn't time out and
gets invisible to the user (e.g. in 'iw wlan0 link'.)
This also fixes a leak in mac80211 where it doesn't always release
the BSS struct properly in all cases where calling this function.
This leak was reported by Ben Greear.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Avoid parsing the original dump message again and again by
allocating a small state struct that is used by the functions
involved in the dump, storing this struct in cb->args[0].
This reduces the memory allocation size as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge mac80211 to avoid conflicts with the nl80211 attrbuf
changes.
Conflicts:
net/mac80211/iface.c
net/wireless/nl80211.c
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since my commit 3713b4e364 ("nl80211: allow splitting wiphy
information in dumps"), nl80211_dump_wiphy() uses the global
nl80211_fam.attrbuf for parsing the incoming data. This wouldn't
be a problem if it only did so on the first dump iteration which
is locked against other commands in generic netlink, but due to
space constraints in cb->args (the needed state doesn't fit) I
decided to always parse the original message. That's racy though
since nl80211_fam.attrbuf could be used by some other parsing in
generic netlink concurrently.
For now, fix this by allocating a separate parse buffer (it's a
bit too big for the stack, currently 1448 bytes on 64-bit). For
-next, I'll change the code to parse into the global buffer in
the first round only and then allocate a smaller buffer to keep
the data in cb->args.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add defines for 5 and 10 MHz channel width and fix channel
handling functions accordingly.
Also check for and report the WIPHY_FLAG_SUPPORTS_5_10_MHZ
capability.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[fix spelling in comment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
only the attributes are required and not the whole netlink info, as the
function accesses the attributes only anyway. This makes it easier to
parse nested beacon IEs later.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In two wiphy dump error cases, most often when the dump allocation
must be increased, the RTNL is leaked. This quickly results in a
complete system lockup. Release the RTNL correctly.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Users may want to send a frame on the current channel
without specifying it.
This is particularly useful for the correct implementation
of the IBSS/RSN support in wpa_supplicant which requires to
receive and send AUTH frames.
Make mgmt_tx pass a NULL channel to the driver if none has
been specified by the user.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I (Johannes) accidentally applied the first version of the patch
("Allow TDLS peer AID to be configured for VHT"). Now apply just
the changes between v1 and v2 to get the AID verification and
prefer the new attribute over the old one.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently mesh uses mandatory rates as the default basic rates. Allow basic
rates to be configured during mesh join. Basic rates are applied only if
channel is also provided with mesh join command.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
[some whitespace fixes, refuse basic rates w/o channel]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a STA has a peer that it hasn't seen any tx activity
from for a certain length of time, the peer link is
expired. This means the inactive STA is removed from the
list of peers and that STA is not considered a peer again
unless it re-peers. Previously, this inactivity time was
always 30 minutes. Now, add it to the mesh configuration
and allow it to be configured. Retain 30 minutes as a
default value.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to use atomic_inc_return() for assigning the wiphy
index made the first wiphy index 1 instead of 0. This is fine,
but we all habitually type "phy0" when we're testing, so make
it go back to 0 instead of 1 by subtracting 1 from the index.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My big locking cleanups caused a problem by registering the
rfkill instance with the RTNL held, while the callback also
acquires the RTNL. This potentially causes a deadlock since
the two locks used (rfkill mutex and RTNL) can be acquired
in two different orders. Fix this by (un)registering rfkill
without holding the RTNL. This needs to be done after the
device struct is registered, but that can also be done w/o
holding the RTNL.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
get_reg_request_treatment() returns 0 in one case but is
defined to return an enum, use the proper value REG_REQ_OK.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The current internal SME implementation in cfg80211 is
very mixed up with the MLME handling, which has been
causing issues for a long time. There are three things
that the implementation has to provide:
* a basic SME implementation for nl80211's connect()
call (for drivers implementing auth/assoc, which is
really just mac80211) and wireless extensions
* MLME events for the userspace SME
* SME events (connected, disconnected etc.) for all
different SME implementation possibilities (driver,
cfg80211 and userspace)
To achieve these goals it isn't necessary to track the
software SME's connection status outside of it's state
(which is the part that caused many issues.) Instead,
track it only in the SME data (wdev->conn) and in the
general case only track whether the wdev is connected
or not (via wdev->current_bss.)
Also separate the internal implementation to not have
callbacks from the SME events, but rather call it from
the API functions that the driver (or rather mac80211)
calls. This separates the code better.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do some cleanups in the cfg80211 SME APIs, which are
only used by mac80211.
Most of these functions get a frame passed, and there
isn't really any reason to export multiple functions
as cfg80211 can check the frame type instead, do that.
Additionally, the API functions have confusing names
like cfg80211_send_...() which was meant to indicate
that it sends an event to userspace, but gets a bit
confusing when there's both TX and RX and they're not
all clearly labeled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
genlmsg_end() can't return an error since it returns the
skb length so remove checks treating the return value as
an error code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to take up the space for devices that don't
support WoWLAN, and most drivers can even make the support
data static const (except where it's modified at runtime.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An active monitor interface is one that is used for communication (via
injection). It is expected to ACK incoming unicast packets. This is
useful for running various 802.11 testing utilities that associate to an
AP via injection and manage the state in user space.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
So far, only net_device * could be passed along with netdevice notifier
event. This patch provides a possibility to pass custom structure
able to provide info that event listener needs to know.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
v2->v3: fix typo on simeth
shortened dev_getter
shortened notifier_info struct name
v1->v2: fix notifier_call parameter in call_netdevice_notifier()
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the current WoWLAN configuration available to drivers
at runtime. This isn't really useful for the normal WoWLAN
behaviour and accessing it can also be racy, but drivers
may use it for testing the WoWLAN device behaviour while
the host stays up & running to observe the device.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By making all the API functions require wdev locking we
can clean up the API a bit, getting rid of the locking
version of each function. This also decreases the size
of cfg80211 by a small amount.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_mutex is similar to the ones I just removed in
cfg80211 but even less useful since it protects global
data, and we hold the RTNL in all places (except module
unload) already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since it just does a quick check of the last regulatory
request, the function doesn't have to hold the reg mutex
but can use RCU instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the driver for some reason successfully finishes
scanning while in p2p_stop_device(), cfg80211 will
still set it to aborted. Simplify this code using the
new 'notified' value and only mark it aborted in case
the driver didn't notify cfg80211 at all (in which
case we also leak the request to not crash, this is
a driver bug.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using separate locks in cfg80211 and mac80211 has always
caused issues, for example having to unlock in places in
mac80211 to call cfg80211, which even needed a framework
to make cfg80211 calls after some functions returned etc.
Additionally, I suspect some issues people have reported
with the cfg80211 state getting confused could be due to
such issues, when cfg80211 is asking mac80211 to change
state but mac80211 is in the process of telling cfg80211
that the state changed (in another way.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Virtually all code paths in cfg80211 already (need to) hold
the RTNL. As such, there's little point in having another
four mutexes for various parts of the code, they just cause
lock ordering issues (and much of the time, the RTNL and a
few of the others need thus be held.)
Simplify all this by getting rid of the extra four mutexes
and just use the RTNL throughout. Only a few code changes
were needed to do this and we can get rid of a work struct
for bonus points.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
VHT uses peer AID in the PARTIAL_AID field in TDLS frames. The current
design for TDLS is to first add a dummy STA entry before completing TDLS
Setup and then update information on this STA entry based on what was
received from the peer during the setup exchange.
In theory, this could use NL80211_ATTR_STA_AID to set the peer AID just
like this is used in AP mode to set the AID of an association station.
However, existing cfg80211 validation rules prevent this attribute from
being used with set_station operation. To avoid interoperability issues
between different kernel and user space version combinations, introduce
a new nl80211 attribute for the purpose of setting TDLS peer AID. This
attribute can be used in both the new_station and set_station
operations. It is not supposed to be allowed to change the AID value
during the lifetime of the STA entry, but that validation is left for
drivers to do in the change_station callback.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Copy & paste mistake - STATION_INFO_TX_BYTES64 is the name of the flag,
not NL80211_STA_INFO_TX_BYTES64.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If a P2P-Device is present and another virtual interface triggers
the connection work, the system crash because it tries to check
if the P2P-Device's netdev (which doesn't exist) is up. Skip any
wdevs that have no netdev to fix this.
Cc: stable@vger.kernel.org
Reported-by: YanBo <dreamfly281@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Authentication takes place in userspace, but the beacon is
generated in the kernel. Allow userspace to inform the
kernel of the authentication method so the appropriate
mesh config IE can be set prior to beacon generation when
joining the MBSS.
Signed-off-by: Colleen Twitty <colleen@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To support auto-loading of wireless modules from netlink users, add module
alias for nl80211 family.
This also adds NL80211_GENL_NAME constant to define the "nl80211" netlink
family name as part of uapi.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add regulatory class for 60GHz band, according
to the last specification.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
