The driver references of_device_id table via of_match_device() so it
will be unused for !CONFIG_OF builds:
drivers/mfd/twl6030-irq.c:359:34: warning: ‘twl6030_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match either via ACPI or OF. Its of_device_id table is
referenced via of_match_ptr() so it will be unused for !CONFIG_OF
builds:
drivers/mfd/axp20x-i2c.c:60:34: warning: ‘axp20x_i2c_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/wm8994-core.c:618:34: warning: ‘wm8994_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/sun4i-gpadc.c:79:34: warning: ‘sun4i_gpadc_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/max77686.c:148:34: warning: ‘max77686_pmic_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/stmfx.c:542:34: warning: ‘stmfx_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/rt5033.c:116:34: warning: ‘rt5033_dt_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/mt6397-core.c:214:34: warning: ‘mt6397_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/max77650.c:215:34: warning: ‘max77650_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/fsl-imx25-tsadc.c:190:34: warning: ‘mx25_tsadc_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/ene-kb3930.c:194:34: warning: ‘kb3930_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9150-core.c:505:34: warning: ‘da9150_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9063-i2c.c:348:34: warning: ‘da9063_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9062-core.c:614:34: warning: ‘da9062_dt_ids’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/da9055-i2c.c:66:34: warning: ‘da9055_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it is not relevant here). This fixes
compile warning (!CONFIG_OF on x86_64):
drivers/mfd/bcm590xx.c:95:34: warning: ‘bcm590xx_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD_OMAP_USB_HOST uses Common Clock Framework thus it cannot be
built on platforms without it (e.g. compile test on MIPS with LANTIQ):
mips-linux-ld: drivers/mfd/omap-usb-host.o: in function `usbhs_omap_probe':
omap-usb-host.c:(.text+0x940): undefined reference to `clk_set_parent'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Change the detection order to priorize DMI table entries over available
ACPI entries.
This makes it more easy for product developers to patch product specific
handling into the driver.
Furthermore it allows to simplify the implementation a bit and
especially to remove the need to force synchronous probing.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Correct power-off programming sequence in order to fix shutting down
devices which are using TPS65910 PMIC.
In accordance to the TPS65910 datasheet, the PMIC's state-machine
transitions into the OFF state only when DEV_OFF bit of DEVCTRL_REG is
set. The ON / SLEEP states also should be cleared, otherwise PMIC won't
get into a proper state on shutdown. Devices like Nexus 7 tablet and Ouya
game console are shutting down properly now.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Zack Pearsall <zpearsall@yahoo.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/mfd/altera-sysmgr.c:155:36-39: WARNING: Suspicious code. resource_size is maybe missing with res
Generated by: scripts/coccinelle/api/resource_size.cocci
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With commit 3a6f0fb7b8 ("regmap: irq: Add support to clear ack
registers"), the cpcap interrupts are no longer getting acked properly
leading to a very unresponsive device with CPUs fully loaded spinning
in the threaded IRQ handlers.
To me it looks like the clear_ack commit above actually fixed a long
standing bug in regmap_irq_thread() where we unconditionally acked the
interrupts earlier without considering ack_invert. And the issue with
cpcap started happening as we now also consider ack_invert.
Tim Harvey <tharvey@gateworks.com> tried to fix this issue earlier with
"[PATCH v2] regmap: irq: fix ack-invert", but the reading of the ack
register was considered unnecessary for just ack_invert, and we did not
have clear_ack available yet. As the cpcap irqs worked both with and
without ack_invert earlier because of the unconditional ack, the
problem remained hidden until now.
Also, looks like the earlier v3.0.8 based Motorola Android Linux kernel
does clear_ack style read-clear-write with "ireg_val & ~mreg_val" instead
of just ack_invert style write. So let's switch cpcap to use clear_ack
to fix the issue.
Fixes: 3a6f0fb7b8 ("regmap: irq: Add support to clear ack registers")
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Laxminath Kasam <lkasam@codeaurora.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
'ret' may be 0 so, dev_err_probe() should be called only when 'ret' is
an error code.
Fixes: 41c9c06c49 ("mfd: stmfx: Simplify with dev_err_probe()")
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently the Kontron sl28cpld Board Management Controller is found only
on Kontron boards equipped with a Freescale Layerscape SoC. Hence add a
dependency on ARCH_LAYERSCAPE, to prevent asking the user about a driver
for this controller when configuring a kernel without Layerscape support.
Fixes: a538ad229b ("mfd: simple-mfd-i2c: Add sl28cpld support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
htcpld_register_chip_i2c() misses to call i2c_put_adapter() in an error
path. Add the missed function call to fix it.
Fixes: 6048a3dd23 ("mfd: Add HTCPLD driver")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There are no separate serial/SPI devices under the at91-usart MFD, but
actually the MFD is used as a serial or a SPI device. There are no DT
sub-nodes for the MFD children, so we should use platform device API to
register the drivers.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
An errata exists for cs47l15 where the reset must be handled
differently and removed before DCVDD is applied. A soft reset is used
for situations where a reset is required to reset state. This does
however, make this part unsuitable for DCVDD supplies with a rise time
greater than 2mS.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The DCVDD supply does not always power down when the CODEC enters
suspend, for example shared regulators or always-on regulators. In
these cases if a register is written back to the default value whilst
the CODEC is in suspend that register will retain the previous value.
As DCVDD never powered down, the register retains its old value and
as the cache sync only synchronises registers that differ from the
default the new value is never written out.
Ensure the registers are in the expected state after suspend by always
resetting the CODEC on resume. This also has the benefit of being
recommended by the datasheet for DCVDD supplies that take longer than
2mS to rise.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
CHECK: Alignment should match open parenthesis
#24: FILE: drivers/mfd/tps65910.c:296:
+ ret = regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_CK32K_CTRL_MASK);
CHECK: Alignment should match open parenthesis
#33: FILE: drivers/mfd/tps65910.c:318:
+ ret = regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_DEV_SLP_MASK);
CHECK: Alignment should match open parenthesis
#42: FILE: drivers/mfd/tps65910.c:326:
+ ret = regmap_set_bits(tps65910->regmap,
TPS65910_SLEEP_KEEP_RES_ON,
CHECK: Alignment should match open parenthesis
#51: FILE: drivers/mfd/tps65910.c:336:
+ ret = regmap_set_bits(tps65910->regmap,
TPS65910_SLEEP_KEEP_RES_ON,
CHECK: Alignment should match open parenthesis
#60: FILE: drivers/mfd/tps65910.c:346:
+ ret = regmap_set_bits(tps65910->regmap,
TPS65910_SLEEP_KEEP_RES_ON,
CHECK: Alignment should match open parenthesis
#69: FILE: drivers/mfd/tps65910.c:358:
+ regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_DEV_SLP_MASK);
CHECK: Alignment should match open parenthesis
#78: FILE: drivers/mfd/tps65910.c:440:
+ if (regmap_set_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_PWR_OFF_MASK) < 0)
CHECK: Alignment should match open parenthesis
#83: FILE: drivers/mfd/tps65910.c:444:
+ regmap_clear_bits(tps65910->regmap, TPS65910_DEVCTRL,
DEVCTRL_DEV_ON_MASK);
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove wrappers around regmap calls to remove now-useless indirection.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use regmap accessors directly for register manipulation - removing
one layer of abstraction.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add the subtype and compatible strings for PM660 and PM660L,
found in various SoCs, including SDM630, SDM636, SDM660 and
SDA variants.
Signed-off-by: AngeloGioacchino Del Regno <kholk11@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify adc_resources[]. The only usage is to assign its address to the
resources field of the mfd_cell struct. This allows the compiler to put
it in read-only memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a couple of static struct resource. The only usage of the
structs is to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a couple of static struct resource. The only usage of the
structs is to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Constify a number of static struct resource. The only usage of the
structs are to assign their address to the resources field in the
mfd_cell struct. This allows the compiler to put them in read-only
memory. Done with the help of Coccinelle.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds syscon_regmap_lookup_by_phandle_optional() function to get an
optional regmap.
It behaves the same as syscon_regmap_lookup_by_phandle() except where
there is no regmap phandle. In this case, instead of returning -ENODEV,
the function returns NULL. This makes error checking simpler when the
regmap phandle is optional.
Suggested-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Intel Platform Monitoring Technology (PMT) is an architecture for
enumerating and accessing hardware monitoring facilities. PMT supports
multiple types of monitoring capabilities. This driver creates platform
devices for each type so that they may be managed by capability specific
drivers (to be introduced). Capabilities are discovered using PCIe DVSEC
ids. Support is included for the 3 current capability types, Telemetry,
Watcher, and Crashlog. The features are available on new Intel platforms
starting from Tiger Lake for which support is added. This patch adds
support for Tiger Lake (TGL), Alder Lake (ADL), and Out-of-Band Management
Services Module (OOBMSM).
Also add a quirk mechanism for several early hardware differences and bugs.
For Tiger Lake and Alder Lake, do not support Watcher and Crashlog
capabilities since they will not be compatible with future product. Also,
fix use a quirk to fix the discovery table offset.
Co-developed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
drivers/mfd/kempld-core.c:556:36: warning: unused variable 'kempld_acpi_table' [-Wunused-const-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fixes the following randconfig build error:
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
simple-mfd-i2c.c:(.text+0x48): undefined reference to `__devm_regmap_init_i2c'
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_init':
simple-mfd-i2c.c:(.init.text+0x14): undefined reference to `i2c_register_driver'
ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_exit':
simple-mfd-i2c.c:(.exit.text+0xd): undefined reference to `i2c_del_driver'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Build this driver on another platforms if COMPILE_TEST=y. Another
drivers may depend on this, for example leds-asic3.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Recent Kontron COMe modules identify the PLD device using the hardware
id KEM0001 in the ACPI table.
This patch adds support for probing the device using the HID and also
retrieving the resources.
As this is not available for all products, the DMI based detection still
needs to be around for older systems. It is executed if no matching ACPI
HID is found during registering the platform driver or no specific
device id is forced.
If a device is detected using ACPI and no resource information is
available, the default io resource is used.
Forcing a device id with the force_device_id parameter and therefore
manually generating a platform device takes precedence over ACPI during
probing.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch implements the basic functions of the BMC chip for some Intel
FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the
Intel MAX 10 CPLD.
This BMC chip is connected to the FPGA by a SPI bus. To provide direct
register access from the FPGA, the "SPI slave to Avalon Master Bridge"
(spi-avmm) IP is integrated in the chip. It converts encoded streams of
bytes from the host to the internal register read/write on the Avalon
bus. So This driver uses the regmap-spi-avmm for register accessing.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for the LP87524B/J/P-Q1 Four 4-MHz Buck Converter. This is a
variant of the LP87565 having 4 single-phase outputs and up to 10 A of
total output current.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This file does not make use of it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
