cx88-alsa can be compiled in (in distro built kernels, for example), but
not used. In those cases, the audio DMA restart is needed for proper sound
on NICAM channels.
This patch enables the DMA restart even with ALSA, but the functions now
check if cx88-alsa is really active.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Although not dangerous, it may allow a normal user with access to a machine
to untune a TV channel.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the FX2 does not reset properly during reboot, it can present an
invalid USB device ID and fail to attach. Prevent this situation
from occuring by resetting the USB part of the card when the PCI part
probes.
Also fix the GPIO configurations so that analog capture will not
inadvertantly reset the USB part.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If an eeprom defined two tuners and they supported more than eight
standards combined (as opposed to each), it would overflow an array.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c: In function 'set_standard':
drivers/media/video/pvrusb2/pvrusb2-i2c-cmd-v4l2.c:33: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'v4l2_std_id'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested on x64 with a bttv board. Most Get ioctls are fixed. The only
non-completely working one is VIDIOCGAUDIO. All other IOR ioctls give the
same results on x86_64 and i386 architectures.
Thanks to Alastair Poole <netstar@gatheringofgray.com> for part of this
patch and tests on ppc64.
Signed-off-by: Alastair Poole <netstar@gatheringofgray.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Acorp TV134DS and FlyDVB-S cards (both based on
tda10086+tda826x)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change causes the pvrusb2 driver to limit horizontal resolution
to be only 720 if 24xxx device hardware is being used. This is a
workaround for an unsolved problem in the driver where if the
resolution is set to something other than 720 the video quality will
be _seriously_ degraded. It only happens on 24xxx devices (29xxx are
unaffected by the problem and unaffected by this change). Once the
problem is finally solved, this small change can be removed.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The internal control implementation in the pvrusb2 driver normally
encodes integer range limits using literal values in a const
structure. This change adds two function pointers, which if not null
will be called through in order to determine integer min / max
values.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 implementation for VIDIOC_[S|TRY]_FMT was hardcoding
limits on the range for allowed resolution, but it would be much
better if we instead just queried the internal control for these
values. This then opens the door for the driver to adjust these
limits based on the detected hardware.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a few miscellaneous issues in the pvrusb2 driver related to use of
the new mpeg controls. This also should fix problems involving
update of the saa7115 / cx25840 configuration as control changes are made.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A buffer was set just before an if block, and then again in both branches
of the if. Obvious coding error.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Shenzhen Tungsten Ages Tech TE-DTV-250 OEM for
Swann PCI TV Tuner Card
Signed-off-by: David Bussenschutt <buzz@oska.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds autodetection support for the AverMedia M150-D
blackbird MPEG encoder / analog video capture card.
This board is known to work with the ASUS PVR 416 configuration.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add initial support for Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
only analog is working for now
Signed-off-by: Eric Thomas <ethomas@claranet.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since kernel include autoconf.h via command line, those config.h inclusion
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is just another Lifeview clone
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The change is just an additional PCI ID
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Analog TV, CVBS, S-video and DVB-T are working,
DVB-S not yet
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The v4l2 API documentation for VIDIOC_ENUMSTD says:
To enumerate all standards applications shall begin at index
zero, incrementing by one until the driver returns EINVAL.
The actual code, however, tests the index this way:
if (index<=0 || index >= vfd->tvnormsize) {
ret=-EINVAL;
So any application which passes in index=0 gets EINVAL right off the bat
- and, in fact, this is what happens to mplayer. So I think the
following patch is called for, and maybe even appropriate for a 2.6.18.x
stable release.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 support should be disabled when no CONFIG_VIDEO_V4L1_COMPAT is defined,
to allow checking for broken V4L2 ports. This is very important during the
migration phase for V4L2 API.
However, userspace apps should be capable of using both APIs, since they need
to test at runtime, via VIDIOCGCAP ioctl, if V4L1 is supported. So, when
__KERNEL__ is not defined, those ioctls and corresponding structs should be
visible.
This patch also removes the obsolete defines HAVE_V4L1 and HAVE_V4L2, that
where causing some confusion, and were replaced by CONFIG_VIDEO_V4L1_COMPAT
and CONFIG_VIDEO_V4L2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tena_9533_di_pal_ranges use 0x04 instead the original 0x08 for the
UHF (range 2) switching. This is wrong and therefore nothing happens.
Restore tuner_ymec_tvf66t5_b_dff_pal_ranges[] to make the UHF switch
working again.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In bugzilla #6943, Maxim Britov reported:
"I can enable Logitech quickcam support in .config, but it want be compile.
I have to add into drivers/media/video/Makefile:
obj-$(CONFIG_USB_QUICKCAM_MESSENGER) += usbvideo/"
He's right, just enable that driver as module while disabling every other
driver that gets into that directory, nothing will get compiled.
This patch fixes the Makefile.
Signed-off-by: Diego Calleja <diegocg@gmail.com>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Without the LNA these tuners perform very poorly (read 'unwatchable') when
the signal is weak.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a wrong statement order the 'standard' module option didn't
work for 'G' model chips.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 assembled the bytes in the wrong order.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The compat_ioctl support of the pwc driver was dropped during the last update of the driver.
I suppose it was by mistake. If yes here is the patch to restore the support.
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@looxix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
