Fix the following sparse warning in mwifiex_cmd_append_11n_tlv:
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:358:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:360:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:366:65: right side has type int
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: warning: invalid assignment: &=
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: left side has type restricted __le16
drivers/net/wireless/marvell/mwifiex/11n.c:368:65: right side has type int
Fixes: 77423fa739 ("mwifiex: fix incorrect ht capability problem")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At present driver gets chan_type by referring to
IEEE80211_HT_PARAM_CHA_SEC_OFFSET, in ASSOC response. Sometimes
AP shows IEEE80211_HT_PARAM_CHA_SEC_OFFSET as above/below in
assoc response, even if the association is done on HT20 channel
only. So, it will be accurate to get econdary channel offset from
firmware.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
IEEE80211_CHAN_NO_HT40PLUS and IEEE80211_CHAN_NO_HT40PLUS channel
flags tell if HT40 operation is allowed on a channel or not.
This patch ensures ht_capability information is modified
accordingly so that we don't end up creating a HT40 connection
when it's not allowed for current regulatory domain.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit bcc920e8f0.
Drivers gets hardware info and updates ht_cap field of
wiphy->bands during initialization. Once updated during init,
ht_cap must not be modified as it reflects the capability
supported by hardwawre. Above patch tries to modify the ht_cap
field and this results in wrongly advertising capabilities during
association.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
High bits of antenna number are reserved in hardware spec,
using low 4 bits represent supported antenna.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lots of the wireless driver vendor Kconfig symol help text says
"questions about cards." (2 spaces between "about" and "cards")
Besides dropping one of those spaces, it also needs some other word
inserted there. Instead of putting each vendor's name there, I chose
to say "these" cards in all of the Kconfig help text.
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multiple interfaces with same bss type could affect each other if
they are sharing the same mac address. In this patch, different
mac address is assigned to new interface which have same bss type
with exist interfaces.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify()
usage with device_lock()") resolves races between driver reset and
removal, but it introduces some new deadlock problems. If we see a
timeout while we've already started suspending, removing, or shutting
down the driver, we might see:
(a) a worker thread, running mwifiex_pcie_work() ->
mwifiex_pcie_card_reset_work() -> pci_reset_function()
(b) a removal thread, running mwifiex_pcie_remove() ->
mwifiex_free_adapter() -> mwifiex_unregister() ->
mwifiex_cleanup_pcie() -> cancel_work_sync(&card->work)
Unfortunately, mwifiex_pcie_remove() already holds the device lock that
pci_reset_function() is now requesting, and so we see a deadlock.
It's necessary to cancel and synchronize our outstanding work before
tearing down the driver, so we can't have this work wait indefinitely
for the lock.
It's reasonable to only "try" to reset here, since this will mostly
happen for cases where it's already difficult to reset the firmware
anyway (e.g., while we're suspending or powering off the system). And if
reset *really* needs to happen, we can always try again later.
Fixes: b014e96d1a ("PCI: Protect pci_error_handlers->reset_notify() usage with device_lock()")
Cc: <stable@vger.kernel.org>
Cc: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit b713bbf147.
The "fix" in question does not actually fix all related problems, and it
also introduces new deadlock possibilities. Since commit b014e96d1a
("PCI: Protect pci_error_handlers->reset_notify() usage with
device_lock()"), the race in question is actually resolved (PCIe reset
cannot happen at the same time as remove()). Instead, this "fix" just
introduces a deadlock where mwifiex_pcie_card_reset_work() is waiting on
device_lock, which is held by PCIe device remove(), which is waiting
on...mwifiex_pcie_card_reset_work().
The proper thing to do is just to fix the deadlock. Patch for this will
come separately.
Cc: Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The last command used to shutdown firmware might be timeout,
and trigger firmware dump in asynchronous pcie/sdio work.
The remove/shutdown handler will continue free core data
structure private/adapter, which might be dereferenced in
pcie/sdio work, finally crash the kernel.
Sync and Cancel pcie/sdio work, could be a fix for above
cornel case. In this way, the last command timeout could
be handled properly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch extend device_dump debugfs function to make it
works for usb interface.
For command timeouts, USB firmware will automatically emit
firmware dump events, so we don't implement device_dump().
For user-initiated dumps, we trigger it by issue firmware
dump event command to firmware, as there is no command
response, do not start 10s timer.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware dump on usb interface is different with current
sdio/pcie chipset, which is based on register operation.
When firmware hang on usb interface, context dump will be
upload to host using 0x73 firmware debug event.
This patch store dump data from debug event and send to
userspace using device coredump API.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch refactor current device dump code to make it generic
for subsequent implementation on usb interface.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
(1) Change virtual interface operation in cfg80211 process reset and
reinitilize private data structure.
(2) Scan result event processed in main process will dereference private
data structure concurrently, ocassionly crash the kernel.
The cornel case could be trigger by below steps:
(1) wpa_cli mlan0 scan
(2) ./hostapd mlan0.conf
Cfg80211 asynchronous scan procedure is not all the time operated
under rtnl lock, here we add the protect to serialize the cfg80211
scan and change_virtual interface operation.
Signed-off-by: Limin Zhu <liminzhu@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware do not support change interface from micro-ap mode
to station mode, forbid this operation
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ/HSCAAoJEG4XJFUm622b2sQH+wXgE1swS9xp1AfV3hcVLGoJ
YjLjR3/BAxsIqkYwhswarTDrD3jsOKrL4ywRk+0BAdR7f2BeOYhQXtZqgjvE8cbu
WWv5LmSwuKM6tF3ujgjQ6yZvgyDHl2d7lZL59EWG05K/yjJuU8ByoUhLKM5IiqPh
SWXj3ZtydgGZm2eZTPyan+MFz91jw/X23Jm/AaIAxayf+1J4n1lNpc4rRhUxh/oy
kGLQ2vsVnegSiHJWTboDFPeRha+daBsbf1MQc0Bh7MzDoWcaqSNX5VgrbaRqp35u
sb9pmPZS4FzvAdU3bJ9AIPa9ujjblEvDp1JIhrfBUqiuTdvXDZ7XtW8kVsJk1RY=
=MvWY
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.15
Mostly fixes this time, but also few new features.
Major changes:
wil6210
* remove ssid debugfs file
rsi
* add WOWLAN support for suspend, hibernate and shutdown states
ath10k
* add support for CCMP-256, GCMP and GCMP-256 ciphers on hardware
where it's supported (QCA99x0 and QCA4019)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Driver is transmitting in 11N rates, when connected to an AP in
TKIP security mode. Add a check to disable_11n to fix the issue.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When joining an IBSS network, wdev->ssid/_len will already be
set, so there's no need to write them. In any case, they are
internal cfg80211 values, and have very little user-visible
impact.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Zaborowski <andrew.zaborowski@intel.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Amitkumar Karwar <amitkarwar@gmail.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Ganapathi Bhat <gbhat@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrew Zaborowski <andrew.zaborowski@intel.com>
Cc: libertas-dev@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use put_unaligned_le32 rather than using byte ordering function and
memcpy which makes code clear.
Also, add the header file where it is declared.
Done using Coccinelle and semantic patch used is :
@ rule1 @
identifier tmp; expression ptr,x; type T;
@@
- tmp = cpu_to_le32(x);
<+... when != tmp
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(x,ptr);
...+>
@ depends on rule1 @
type j; identifier tmp;
@@
- j tmp;
...when != tmp
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When a user requests scan, driver sends multiple scan requests
to firmware, which might be active or passive. Firmware will
send channel statistics for each channel in the request. This will
be stored in chan_stats array.
Few channels might report hidden SSIDs in passive scan results.
So, once the original scan request is finished, driver issues an
active scan request for all channels which reported hidden SSIDs.
This will cause duplicates in the chan_stats array. At worst,
every channel will have a hidden SSID, in which case the driver
can issue active scan requests for each channel. So the complete
scan statistics size will be twice of existing limit.
At present maximum number of channels returned in scan statistics
is 31(BG) + 14(A) = 45. Clearly there will be an overflow of the
chan_stats array in the above mentioned scenario. To fix this
double the size of chan_stats array.
Signed-off-by: Rohit Fule <rohitf@marvell.com>
Signed-off-by: Mangesh Malusare <mmangesh@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sta_list_spinlock looks to be used to control locking of the
list. Specifically when someone has the lock they may be allowed
to modify or delete elements of the list.
That implies that we shouldn't access the fields of the elements
returned by mwifiex_get_sta_entry() after we've released the
spinlock. Let's make some small changes so this is true.
It's unlikely that this matters since it looks to be just error
handling, but it's nice to be clean.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's absolutely no reason to check to see if a list is empty
before iterating through it. It's just like writing code like
this:
if (count != 0) {
for (i = 0; i < count; i++) {
...
}
}
The loop will already be avoided if "count == 0" so there was no
reason to check.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver will advertise RANDOM_MAC support only if the device
supports this feature.
Signed-off-by: Karthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate the read-only const array tos_to_ac on the stack,
instead make it static. Makes the object code smaller by 250 bytes:
Before:
text data bss dec hex filename
26104 2720 128 28952 7118 wmm.o
After:
text data bss dec hex filename
25758 2816 128 28702 701e wmm.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoid calculating random MAC address in driver. Instead make
use of 'get_random_mask_addr()' function.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Application will keep track of whether MAC address randomization
is enabled or not during scan. But at present driver is storing
'random_mac' in mwifiex_private which implies even after scan is
done driver has some reference to the earlier 'scan request'. To
avoid this, make use of 'mac_addr' variable in 'scan_request' to
store 'random_mac'. This structure will be freed by cfg80211 once
scan is done.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Don't populate const arrays on the stack, instead make them static
Makes the object code smaller by nearly 300 bytes:
Before:
text data bss dec hex filename
69260 16149 576 85985 14fe1 cfg80211.o
After:
text data bss dec hex filename
68385 16725 576 85686 14eb6 cfg80211.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
call to memset to assign 0 value immediately after allocating
memory with kzalloc is unnecesaary as kzalloc allocates the memory
filled with 0 value.
Semantic patch used to resolve this issue:
@@
expression e,e2; constant c;
statement S;
@@
e = kzalloc(e2, c);
if(e == NULL) S
- memset(e, 0, e2);
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If driver is loaded with 'mfg_mode' enabled, then the sending
commands are not allowed. So, skip sending commands, to firmware
in mwifiex_add_virtual_intf if 'mfg_mode' is enabled.
Fixes: 7311ea8500 ("mwifiex: fix AP start problem for newly added interface")
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver sends a series of scan commands to firmware to serve a
user scan request. If an intermediate scan command fails, driver
aborts the scan but it is not being informed to cfg80211. This
will cause issues in applications performing periodic scans.
Fix this by informing scan abort.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
At the end of user scan request, driver will perform an active
scan for hidden SSIDs in passive channels. While doing this,
driver unconditionally adding random_mac in scan command, which
is no expected. It should add random_mac only if scan_request
has NL80211_SCAN_FLAG_RANDOM_ADDR flag set.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver should use random MAC address only if the scan is
requested by user(provided NL80211_SCAN_FLAG_RANDOM_ADDR
is set in scan request). It should not be used for a scan
performed before association.
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch check whether userspace beacon data include country
ie, if so then download command to enable 11d setup in firmeare
accordingly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per below statement about p2p device address in WFA P2P
spec $2.4.3:
The P2P Device Address of a P2P Device shall be its globally
administered MAC address, or its globally administered MAC
address with the locally administered bit set.
This patch follow above statement, using a separate device
address for p2p interface
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch wrapper wps ie in pass through tlv, so that
firmware could parse correctly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 4d7ab36f0c ("mwifiex: Do not change bss_type in
change_virtual_intf") kept original bss_type unchanged. bss_num should
keep the same style, in this way. Unique tuple (bss_type, bss_num) will
be able to locate the right priv structure.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver is doing netif_carrier_off during suspend, which will set
the IFF_LOWER_UP flag to 0. As a result certain applications
will think this as a real carrier down and behave accordingly.
This will cause issues like loss of IP address, for example. To
fix this use netif_device_dettach during suspend.
Fixes: 0026b32d72 ('mwifiex: fix Tx timeout issue during suspend test')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Ganapathi Bhat <gbhat@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, we might using wifi-only firmware with a combo firmware name,
in this case, do not need to filter bluetooth part from header.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
uninitilized variable, such as .add_req_result might be magic stack
value. Initialize the structure to make it clean.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that some IEs get missed during association.
This patch correct the old IE parse code. sme->ie will be
store as wpa ie, wps ie, wapi ie and gen ie accordingly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in mwifiex_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trivial fix to spelling mistake in aggr_ctrl module parameter
message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
