When ath_tx_complete_aggr() is called, it's responsible for returning
all buffers in the linked list. This was not done when the STA lookup
failed, leading to a race condition that could leak a few buffers when
a STA just disconnected.
Fix this by immediately returning all buffers to the free list in this case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It looks like it might be possible for a TID to be paused, while still
holding some queued buffers, however ath_tx_node_cleanup currently only
iterates over active TIDs.
Fix this by always checking every allocated TID for the STA that is being
cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
(Changed title, was "wl1251: Use MODULE_ALIAS macro at correct postion
for SPI bus". -- JWL)
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Elsewhere in the "optimized" functions, the "2" constants are used.
NV_TX_VALID and NV_TX2_VALID have the same value.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_device allocated with alloc_eip_netdev() must be freed.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Statistics are available and the driver doesn't need the actual frame.
This TCP/UDP and IP headers checksum errors will still be passed to the
driver.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases the firmware may be dead. Instead we dump the firmware
parameters and then restart it.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats, we can remove the
instance of this from the adapter structure.
Based on original patch by Kulikov Vasiliy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
drivers/net/ioc3-eth.c | 49 ++++++++++++++++++++++++-----------------------
1 files changed, 25 insertions(+), 24 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Since net_device has an instance of net_device_stats,
we can remove the instance of this from the adapter structure.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces all usage of dev_dbg with netdev_dbg.
A side effect is that the pointer to the platform device in the adapter
struct can be removed.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USB drivers should not use urb->status directly because
it is scheduled to become a parameter. This does the conversion
for drivers/net/usb
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch restores the ability to set msglvl through ethtool.
The issue was introduced by:
commit 849c45423c
CC: Joe Perches <joe@perches.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes UDP from the supported protocols for RSS hashing. The
reason for removing this protocol is because IP fragmentation was causing a
network flow to be broken into two streams, one for fragmented, and one for
non-fragmented and this in turn was causing out-of-order issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These config register values will be useful when the memory registers
are returning 0xffffffff which has been reported.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add skb->rxhash support for TCP packets only because the bnx2 RSS hash
does not hash UDP ports.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor change to use MSI-X even if there is only one CPU. This allows
the CNIC driver to always have a dedicated MSI-X vector to handle
iSCSI events, instead of sharing the MSI vector.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio net will never try to overflow the TX ring, so the only reason
add_buf may fail is out of memory. Thus, we can not stop the
device until some request completes - there's no guarantee anything
at all is outstanding.
Make the error message clearer as well: error here does not
indicate queue full.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY)
Cc: stable@kernel.org # .34.x (s/virtqueue_/vi->svq->vq_ops->/)
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently fill all of RX ring, then add_buf
returns ENOSPC, which gets mis-detected as an out of
memory condition and causes us to reschedule the work,
and so on forever. Fix this by oom = err == -ENOMEM;
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a number of issues in the statistics gathering of
the s2io driver.
On Xframe adapters, the received multicast statistics counter includes
pause frames which are not indicated to the driver. This can cause
issues where the multicast packet count is higher than what has actually
been received, possibly higher than the number of packets received.
The driver software counters are replaced with the adapter hardware
statistics for rx_packets, rx_bytes, and tx_bytes. It also uses the
overflow registers to determine if the statistics wrapped the 32bit
register (removing the window of having a statistic value less than the
previous call). rx_length_errors statistic now includes undersized
packets in addition to oversized packets in its counting. Finally,
rx_crc_errors are now being counted.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some ocasions the function qlge_io_resume() tries to add a
pending timer, which causes the system to hit the BUG() on
add_timer() function.
This patch removes the timer during the EEH recovery.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge driver calls add_timer() instead of mod_timer().
This patch changes add_timer() to mod_timer(), which seems a better
solution.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev_printk() follows the net_device's parent device pointer, so
we must set that earlier than we previously did.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c17b274dc2.
That change was reported to break rndis_wlan support for the WUSB54GS.
Reported-by: Luís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
For newer devices (6000g2a and 6000g2b), the sensitivity table send to
uCode require additional table entries to help sensitivity calibration.
All the additional entries has fix data for now, but do expect the value
will be change in the future when device become more stable.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Code clean up to change name from having 5000 as part of name which easy
to confuse and think it is for 5000 series devices to more
generic _agn name since it is being used by multiple _agn devices.
No functional changes.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
"Flush" request can come from two different sources, it can either from
mac80211, or from device when the operation is needed. Here
adding the support for device issue "flush" request.
When receive tx complete with status is TX_STATUS_FAIL_RFKILL_FLUSH,
issue REPLY_TXFIFO_FLUSH command to uCode to flush out all the tx frames
in queues.
In this condition, since mac80211 has no knowledge of "flush" operation,
driver need to stop all the tx queues and wait for the operation
completed before wake up the queues for frames transmission.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Adding flush callback support in the driver. Two type of flush can be
issued by mac80211:
1. drop = true: frame drop is ok, issue REPLY_TXFIFO_FLUSH host command
to uCode to drop all the frames in tx fifo queues; then return the
control back to mac80211
2. drop = false: wait for either all the frames in tx fifo queues been
transmitted, or timeout; then return the control back to mac80211
If the flush request coming from mac80211, mac80211 will make sure there
are no additional frames push down to driver before flush operation is
completed.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When parsing TLV during loading firmware, if encounter any TLV error,
log the error message to help debugging.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
fw_restart module parameter was broken by the recent check for stuck
queue patch, driver check the fx_restart module parameter
before reload the firmware; but the stuck queue timer kick in after
firmware error and reload the firmware even fw_restart=0. In this case,
driver should not reload the firmware, it is important to help debugging
uCode error.
The only case we can ignore the module parameter is when user request
firmware reload from debugfs, which can bypass the checking and perform
firmware reload all the time.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Commit eed8e22f01 added support for using
multicast key lookup to support per-vif/sta keys for AP and ad-hoc.
Unfortunately, it also introduced a crash in ad-hoc mode when the sta
pointer is NULL, which happens when setting up an interface with WEP
keys. This patch fixes it by falling back to the assigned key index.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_check_alive() occasionally returns false, as the hardware
is still processing data in a specific state. Fix this issue by
repeating the test a few times with longer delay inbetween attempts.
This gets rid of excessive hardware resets that appear frequently on
some AR9132 based devices, but could also happen on AR9280.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This refactors the noise floor range checks to make them generic,
and adds proper ranges for each supported chip type.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This includes the following changes/fixes:
- a bugfix for stuck beacon issues
- timing changes for improved performance
- AGC setting improvements
- fixes for high temperature issues on some chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This format is generated by the initval tool, available at:
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/initvals-tool.git
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.
The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.
This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Both ETH_FLAG_LRO and NETIF_F_LRO have the same value, but NETIF_F_LRO
is intended to use with netdev->features.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add explanatory comment to avoid confusion when a pointer is set
to the second word of an array instead of the customary cast of a
pointer to the beginning of the array.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igb online link test was always reporting pass because instead of
checking for if_running it was checking for netif_carrier_ok.
This change corrects the test so that it is run if the interface is running
instead of checking for netif carrier ok.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the value of max_vfs at the time of assignment of vfs_allocated_count.
The previous check in igb_probe_vfs was too late as by that time the rx/tx
rings were initialized with the wrong offset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82576 expects the second rx queue in any pool to receive L2 switch
loop back packets sent from the second tx queue in another pool. The
82576 VF driver does not enable the second rx queue so if the PF driver
sends packets destined to a VF from its second tx queue then the VF
driver will never see them. In SR-IOV mode limit the number of tx queues
used by the PF driver to one. This patch fixes a bug reported in which
the PF cannot communciate with the VF and should be considered for 2.6.34
stable.
CC: stable@kernel.org
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
82580 NICs can have up to 4 functions. This fixes phy accesses
to use the correct locks for functions 2 and 3.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add error checking to DMA descriptor rings initialization code.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
be2net driver is currently not showing correct phy details in certain cases.
This patch fixes it.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ehea_get_stats calls ehea_h_query_ehea_port, which
can sleep, we can also sleep when allocating a page in
this function. This fixes some memory allocation failure
warnings seen under low memory conditions.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for 1G SFP+ PHY's to 82599.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow ethtool to query the number of RX rings, the fields used in RX
flow hashing and the hash indirection table.
Allow ethtool to update the RX flow hash indirection table.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only some netdev feature flags correspond directly to ethtool feature
flags. ethtool_op_get_flags() does the right thing.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documented error code for attempts to set unsupported flags (or
to clear flags that cannot be disabled) is EINVAL, not EOPNOTSUPP.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_op_set_flags() does not check for unsupported flags, and has
no way of doing so. This means it is not suitable for use as a
default implementation of ethtool_ops::set_flags.
Add a 'supported' parameter specifying the flags that the driver and
hardware support, validate the requested flags against this, and
change all current callers to pass this parameter.
Change some other trivial implementations of ethtool_ops::set_flags to
call ethtool_op_set_flags().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct shift factor for extracting the SGE DMA Ingress Padding
Boundary. Was accidentally using the register field's shift which was
close enough (4 instead of the propper value of 5) that it actually
sort of worked for various packet sizes ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove obsolete comment about the lack of a TX Timer Callback -- which
we now _do_ have ...
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.
What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.
See more information including the relevant functions below:
System 1 System 2
bond0 bond0
ping <system2>
ARP request --------->
<--------- ARP reply
+->rlb_arp_recv <---------------------+ <--- loop begins
| rlb_update_entry_from_arp |
| client_info->ntt = 1; |
| bond_info->rx_ntt = 1; |
| |
| <communication succeed> |
| |
| bond_alb_monitor |
| rlb_update_rx_clients |
| rlb_update_client |
| arp_create(ARPOP_REPLY) |
| send ARP reply --------------> V
| send ARP reply -------------->
| rlb_arp_recv
| rlb_update_entry_from_arp
| client_info->ntt = 1;
| bond_info->rx_ntt = 1;
| < snipped, same as in system 1>
+------- <-------------- send ARP reply
<-------------- send ARP reply
Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.
This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ibm p7 architecure seems to reorder memory accesses more
aggressively than previous ppc64 architectures. This requires memory
barriers to ensure that rx/tx doorbells are pressed only after
memory to be DMAed is written.
Signed-off-by: Sathya Perla <sathyap@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code is off by one because we should start counting at
zero. So the size of the resource is end - start + 1. I switched it to
use resource_size() to do the calculation.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When issuing a reset, the TSF value is lost in the hardware because of
the 913x specific cold reset. As with some AR9280 cards, the TSF needs
to be preserved in software here.
Additionally, there's an issue that frequently prevents a successful
TSF write directly after the chip reset. In this case, repeating the
TSF write after the initval-writes usually works.
This patch detects failed TSF writes and recovers from them, taking
into account the delay caused by the initval writes.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CC [M] drivers/net/wireless/rt2x00/rt2800lib.o
drivers/net/wireless/rt2x00/rt2800lib.c: In function 'rt2800_ampdu_action':
drivers/net/wireless/rt2x00/rt2800lib.c:2821: warning: unused variable 'rt2x00dev'
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Latest rt2870 legacy driver also sets BBP_CSR_CFG_BBP_RW_MODE to 1
when reading or writing the EEPROM. This means we can make the
BBP reading and writing completely equal on all platforms.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy driver indicates that BBP1_TX_ANTENNA must be set
to 0 for TXPATH values of 1 and 3. So the previous statement
that nothing should be done for TXPATH = 3, is false.
Furthermore, remove the false BBP3_RX_ANTENNA initialization
when TXPATH is 1 for PCI and SOC devices. This field will always
be overridden in the next switch statement, making this initialization
bogus. History of this line indicates it was there from the beginning,
and was once caught as typo. Instead of replacing the line with the
correct line, the correct line was added...
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IEEE80211_HT_CAP_RX_STBC is a 2 bit flag, and should thus
never be set as normal flag. Instead we must read the number
of RX paths from the EEPROM and set the IEEE80211_HT_CAP_RX_STBC
with the correct value (using the same logic as the number of TX
streams).
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is removed the according beacon entry should be reset.
The current approach to only clear the first word is not enough to stop
the device from sending out the beacon, hence resulting in beacons being
sent out for already removed interfaces.
Fix this by invalidating the entire TXWI in front of the beacon instead
of only the first word.
Also clear all beacons during startup in the same way.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the link tuning is based on average RSSI values taken from all received
frames it doesn't make sense to enable it in AP mode where every associated
station provides independent RSSI values. Furthermore the legacy drivers
don't enable link tuning in AP mode as well.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix rt61pci beacon updates in the same way as rt2800pci. rt61pci didn't
update the beacon template after each beacon interval, resulting in the
DTIM count being incorrect (if DTIM period > 1). Fix this by calling
rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci didn't update the beacon template after each beacon interval,
resulting in the DTIM count being incorrect (if DTIM period > 1). Fix this
by calling rt2x00lib_beacondone after the current beacon was sent out.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MAC_BSSID_DW1_BSS_ID_MASK must be set to the mask 3, to
enable 8 BSSID's. The MAC_BSSID_DW1_BSS_BCN_NUM is initialized
to 7 to enable the 8 beacons.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align with the latest versions of the Ralink legacy driver(s).
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Align with the way PCI devices are handled, even though it is not
strictly necessary.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the {usb,pci} specific write_tx_data functions are no longer
present we can rename the write_tx_datadesc callback function back to
its old name.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the write_tx_data functions are merged, also merge the relevant
parts of the txdone handling into common code, rather than {usb,pci}
specific code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that rt2x00pci_write_tx_data and rt2x00usb_write_tx_data are similar
we can merge them in a single function in rt2x00queue.c.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to fill the TX URB this early, and moving it to the
rt2x00usb_kick_tx_entry function allows us to merge the PCI and USB
variants of the write_tx_data function.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We forgot to clear the SKBDESC_DESC_IN_SKB when the descriptor was removed
from the front of the skb.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The update_bssid is set only when BSS_CHANGED_BSSID is used,
but the check if that field is true is done later in the function
but also only when BSS_CHANGED_BSSID is set. This makes the
variable useless, as it can never result in a negative check.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the Master mode case, we initialized the BSSID as the MAC
address, but never wrote it into the registers. This causes
Hardware crypto to break in Master mode when receiving frames
which require the BSSID to be filled in.
This is safe for STA mode since the BSSID will be initialized
to 00:00:00:00:00 at this point, but will be set to the correct
value later when the device associates.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to implement tx mpdu aggregation we only have to implement
the ampdu_action callback such that mac80211 allows negotiation of
blockack sessions.
The hardware will handle everything on its own as long as the ampdu
flag in the TXWI struct is set up correctly and we translate the tx
status correctly.
For now, refuse requests to start rx aggregation.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MPC8313ECE says:
"If the controller receives a 1- or 2-byte frame (such as an illegal
runt packet or a packet with RX_ER asserted) before GRS is asserted
and does not receive any other frames, the controller may fail to set
GRSC even when the receive logic is completely idle. Any subsequent
receive frame that is larger than two bytes will reset the state so
the graceful stop can complete. A MAC receiver (Rx) reset will also
reset the state."
This patch implements the proposed workaround:
"If IEVENT[GRSC] is still not set after the timeout, read the eTSEC
register at offset 0xD1C. If bits 7-14 are the same as bits 23-30,
the eTSEC Rx is assumed to be idle and the Rx can be safely reset.
If the register fields are not equal, wait for another timeout
period and check again."
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8313ECE says:
"For TOE=1 huge or jumbo frames, the data required to generate the
checksum may exceed the 2500-byte threshold beyond which the controller
constrains itself to one memory fetch every 256 eTSEC system clocks.
This throttling threshold is supposed to trigger only when the
controller has sufficient data to keep transmit active for the duration
of the memory fetches. The state machine handling this threshold,
however, fails to take large TOE frames into account. As a result,
TOE=1 frames larger than 2500 bytes often see excess delays before start
of transmission."
This patch implements the workaround as suggested by the errata
document, i.e.:
"Limit TOE=1 frames to less than 2500 bytes to avoid excess delays due to
memory throttling.
When using packets larger than 2700 bytes, it is recommended to turn TOE
off."
To be sure, we limit the TOE frames to 2500 bytes, and do software
checksumming instead.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPC8313ECE says:
"If MACCFG2[Huge Frame]=0 and the Ethernet controller receives frames
which are larger than MAXFRM, the controller truncates the frames to
length MAXFRM and marks RxBD[TR]=1 to indicate the error. The controller
also erroneously marks RxBD[TR]=1 if the received frame length is MAXFRM
or MAXFRM-1, even though those frames are not truncated.
No truncation or truncation error occurs if MACCFG2[Huge Frame]=1."
There are two options to workaround the issue:
"1. Set MACCFG2[Huge Frame]=1, so no truncation occurs for invalid large
frames. Software can determine if a frame is larger than MAXFRM by
reading RxBD[LG] or RxBD[Data Length].
2. Set MAXFRM to 1538 (0x602) instead of the default 1536 (0x600), so
normal-length frames are not marked as truncated. Software can examine
RxBD[Data Length] to determine if the frame was larger than MAXFRM-2."
This patch implements the first workaround option by setting HUGEFRAME
bit, and gfar_clean_rx_ring() already checks the RxBD[Data Length].
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed brace, static initialization, comment, whitespace and spacing
coding style issues.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This avoids scheduling in atomic context and also means that IRQs
will only be deferred for relatively short periods of time.
Previously discussed in:
http://article.gmane.org/gmane.linux.network/155024
Reported-by: Arne Nordmark <nordmark@mech.kth.se>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just
add a test to check skb->protocol. It may crash on short packets due
to ip_hdr() access.
Signed-off-by: Guillaume Gaudonville <guillaume.gaudonville@6wind.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling the tx laser while receiving DMA requests
can hang the device. After this occurs the device
is in a bad state. The GPIO bit never clears when
PCI master access is disabled and a reboot is required
to get the device in a good state again.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added to 2.6.34:
commit 5f6c018199
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date: Wed Apr 14 16:04:23 2010 -0700
ixgbe: fix bug with vlan strip in promsic mode
among other things added a function called ixgbe_vlan_filter_enable.
This new function wants to access and set some rx_ring parameters, but
adapter->rx_ring has already been freed. This simply moves the free
until after the access and makes __ixgbe_shutdown look more like
ixgbe_remove.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on community feedback, EEE should be disabled by default until the
IEEE802.3az specification has been finalized.
Cc: bhutchings@solarflare.com
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As requested by Dave Miller. A follow-on set of patches will allow for
ethtool to enable/disable the feature instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 84f4ee902a causes compile warnings on
architectures that have unsigned long long's that are not 64-bit, e.g.
ia64.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Should e1000_test_msi() fail to see an msi interrupt, it attempts to
fallback to legacy INTx interrupts. But an error in the code may prevent
this from happening correctly.
Before calling e1000_test_msi_interrupt(), e1000_test_msi() disables SERR
by clearing the SERR bit from the just read PCI_COMMAND bits as it writes
them back out.
Upon return from calling e1000_test_msi_interrupt(), it re-enables SERR
by writing out the version of PCI_COMMAND it had previously read.
The problem with this is that e1000_test_msi_interrupt() calls
pci_disable_msi(), which eventually ends up in pci_intx(). And because
pci_intx() was called with enable set to 1, the INTX_DISABLE bit gets
cleared from PCI_COMMAND, which is what we want. But when we get back to
e1000_test_msi(), the INTX_DISABLE bit gets inadvertently re-set because
of the attempt by e1000_test_msi() to re-enable SERR.
The solution is to have e1000_test_msi() re-read the PCI_COMMAND bits as
part of its attempt to re-enable SERR.
During debugging/testing of this issue I found that not all the systems
I ran on had the SERR bit set to begin with. And on some of the systems
the same could be said for the INTX_DISABLE bit. Needless to say these
latter systems didn't have a problem falling back to legacy INTx
interrupts with the code as is.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
CC: stable@kernel.org
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't descend to wireless unless it is actually used.
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following changes are made:
1.Obtain capabilities of Nic partition.
2.Configure tx bandwidth of particular Nic partition.
3.Configure the eswitch for setting port mirroring, enable mac
learning, promiscous mode.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver uses FW API version 2 and thus code corresponding to FW API
version 1 has become obsolete. Clean up this from the driver.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello all:
This patch fixes what Ben mentioned, namely duplicated ids.
From: David J. Choi <david.choi@micrel.com>
Body of the explanation: This patch has changes as followings;
-support the interrupt from phy devices from Micrel Inc.
-support more phy devices, ks8737, ks8721, ks8041, ks8051 from Micrel.
-remove vsc8201 because this device was used only internal test at Micrel.
Signed-off-by: David J. Choi <david.choi@micrel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return EOPNOTSUPP in ethtool_ops->set_flags.
Fix coding style while at it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the CAIF SPI Protocol Driver for
CAIF Link Layer.
This driver implements a platform driver to accommodate for a
platform specific SPI device. A general platform driver is not
possible as there are no SPI Slave side Kernel API defined.
A sample CAIF SPI Platform device can be found in
.../Documentation/networking/caif/spi_porting.txt
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "depends on" instead of "if" in Kconfig files.
Fixed CAIF debug flag, and removed unnecessary clean-* options.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new Makefile for T4 PCI-E SR-IOV Virtual Function driver "cxgb4vf".
Signed-off-by: Casey Leedom
Signed-off-by: David S. Miller <davem@davemloft.net>
Add core T4 PCI-E SR-IOV Virtual Function hardware definitions and device
communication code.
Signed-off-by: Casey Leedom
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to provision T4 PCI-E SR-IOV Virtual Functions with hardware
resources.
Signed-off-by: Casey Leedom
Signed-off-by: David S. Miller <davem@davemloft.net>
Split cpl_tx_pkt_lso into core message structure and encapsulated message,
make RSPD_LEN macro match other response descriptor macros.
Signed-off-by: Casey Leedom
Signed-off-by: David S. Miller <davem@davemloft.net>
We started getting:
WARNING: vmlinux.o(.data+0x20bd0): Section mismatch in reference from
the variable octeon_mdiobus_driver to the function
.init.text:octeon_mdiobus_probe()
This fixes it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We started getting:
WARNING: drivers/net/built-in.o(.data+0x10f0): Section mismatch in
reference from the variable octeon_mgmt_driver to the function
.init.text:octeon_mgmt_probe()
This fixes it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for netpoll over bonded interfaces was added here:
commit f6dc31a85c
Author: WANG Cong <amwang@redhat.com>
Date: Thu May 6 00:48:51 2010 -0700
bonding: make bonding support netpoll
but it is bad enough that we should probably just disable netpoll over
bonding until some of the locking logic in the bonding driver is changed
or converted completely to RCU. Simple actions like changing the active
slave in active-backup mode will hang the box if a high enough printk
debugging level is enabled.
Keeping the old code around will be good for anyone that wants to work
on it (and for after the RCU conversion), so I propose this small patch
rather than ripping it all out.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use u64_stats_sync infrastructure to implement 64bit stats.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently much of the code assumes that a specific window has been
selected, while a few functions save and restore the window. This
makes it impossible to introduce fine-grained locking.
Make those assumptions explicit by introducing wrapper functions
to set the window and read/write a register. Use these everywhere
except vortex_interrupt(), vortex_start_xmit() and vortex_rx().
These set the window just once, or not at all in the case of
vortex_rx() as it should always be called from vortex_interrupt().
Cache the current window in struct vortex_private to avoid
unnecessary hardware writes.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Arne Nordmark <nordmark@mech.kth.se> [against 2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dynamic LRO diable support for mlx4 net driver.
It also fixes a bug of mlx4, which checks NETIF_F_LRO flag in rx
path without rtnl lock.
(I don't have mlx4 card, so only did compiling test. Anyone who wants
to test this is more than welcome.)
This is based on Neil's initial work too, and heavily modified based
on Stanislaw's suggestions.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Neil Horman <nhorman@redhat.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dynamic LRO disable support for s2io net driver,
enables LRO by default, increases the driver version number, and
corrects the name of the LRO modparm.
This is mostly Wang's patch based on Neil's initial work, heavily
modified based on Ramkrishna's suggestions. This has been tested on
a Neterion Xframe adapter and verified via adapter LRO statistics.
Signed-off-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Neil Horman <nhorman@redhat.com>
Acked-by: Neil Horman <nhorman@redhat.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Ramkrishna Vepa <Ramkrishna.Vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'bf_retries' field of the ath_buf structure was used for both
software retries (AMPDU subframes) and hardware retries (legacy
frames). This led to a wrong retry count being reported for the A-MPDU
rate control stats.
This patch changes the code to no longer use bf_retries for reporting
retry counts, but instead always using the real on-chip retry count
from the ath_tx_status.
Additionally, if the first subframe of an A-MPDU was not acked, the tx
status report is submitted along with the first acked subframe, which
may not contain the correct rates in the tx info.
This is easily corrected by saving the tx rate info before looping over
subframes, and then copying it back once the A-MPDU status report is
submitted.
In my tests this change improves throughput visibly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit 39d5b2c83c "ath5k: update
AR5K_PHY_RESTART_DIV_GC values to match masks" i introduced a regression on PHY
chips older than AR5K_SREV_PHY_5413, which caused signal values to be about
10dB less that before. This patch reverts the AR5K_PHY_RESTART_DIV_GC values to
the same values which were effectively used before (without the bitmask
mistake). This brings signal levels back to normal on these PHY chips.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit e13647c1 (phylib: Add support for the LXT973 phy.) added a new ID
but neglected to also add it to the MODULE_DEVICE_TABLE.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When pci_enable_msix() returned ret<0, entries and vxge_entries were leaked.
While at it, use the centralized exit idiom in the function.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6b10de38f0 (loopback: Implement 64bit stats on 32bit arches)
introduced 64bit stats in loopback driver, using a private seqcount and
private helpers.
David suggested to introduce a generic infrastructure, added in (net:
Introduce u64_stats_sync infrastructure)
This patch reimplements loopback 64bit stats using the u64_stats_sync
infrastructure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the call to phy_connect fails, we will return directly instead of freeing
the previously allocated struct net_device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
CC: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
smc91c92_cs:
Fix the problem that lan & modem does not work simultaneously
in the Megahertz multi-function card.
We need to write MEGAHERTZ_ISR to retrigger interrupt.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insertion of the Falcon hash is unreliable.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We will use this hash key for Toeplitz IPv4 hashing too.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hash appears immediately before the packet data, not at the
beginning of the buffer. This means we can easily use negative offsets
from the start of packet data, so adjust the data and length at the
top of __efx_rx_packet() instead of wherever we consume the hash.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Update copyright
2) Fix hardware queue descriptor field size CQ_ENET_RQ_DESC_FCOE_SOF_BITS
3) Include rtnetlink.h instead of if_link.h
4) Selectively flush writes to interrupt mask register
5) Use pci_enable_device_mem
6) Remove unused variables and header files
7) Fix size mismatch between memory alloc and free operations of a variable
8) Check for non null arguments to vic_provinfo_alloc
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle surprise hardware removals gracefully during devcmd issue and init,
cleanup of queues.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware has the loopback capability to queue the packets transmitted from
a device to the receive queue of the same device. enic now supports the
loopback capability.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the receive queue buffer allocations into blocks of 32 entries when
ring size is less than 64, otherwise use 64 entries per block.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new firmware devcmds - CMD_PROXY_BY_BDF, CMD_PACKET_FILTER_ALL,
CMD_ENABLE_WAIT.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace all printk routines with the (netdev|dev|pr)_<level> macros that
provide verbose logs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wrapper routines that issue devcmds to firmware and ensure that a
devcmd lock is held for each devcmd call.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port profile information for a dynamic enic device is set by the upper
layers, that are oblivious to the device reset operation. We do not want a
reset operation erase the network state of a dynamic enic device as there
is no way to set up the port profile information again. Hence a lighter
reset operation called hang reset is used. Hang reset, unlike soft reset
does not reset the network state and resets the host side state only.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current ingress vlan rewrite mode setting lets the hardware strip off
the tag control information of a packet received on native vlan. As a
result, the priority bits are also lost. The fix is to change the ingress
vlan rewrite mode setting such that the complete tag control information is
retained for packets that belong to native vlan.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic now uses the GRO mechanism instead of LRO to pass skbs to upper
layers.
Signed-off-by: Scott Feldman <scofeldm@cisco.com>
Signed-off-by: Vasanthy Kolluri <vkolluri@cisco.com>
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This eliminates some of the duplicate code for the various devices
that require the same basic kcq handling.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By doing more work in the common function cnic_get_kcqes(), and
making full use of the kcq_info structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By creating a common data stucture kcq_info for all devices, the kcq
(kernel completion queue) for all devices can be allocated by common
code.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code makes assumptions about the CID (context ID) memory
space and starting CID that may not be always correct when firmware
changes. In particular, BNX2_ISCSI_START_CID may not always be fixed.
We now calculate cp->max_cid_space and cp->iscsi_start_cid dynamically
instead of using fixed constants. The unused cp->max_iscsi_conn is also
eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Radio calibration (chain noise and sensitivity) should be allowed to
be disabled from debugfs if compiled with CONFIG_IWLWIFI_DEBUGFS. For both
6000g2a and 6000g2b, the parameters are missing in "cfg", which cause
user can not disable the radio calibration manually; add the support to
allow the operation.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This message is encountered regularly and we need to take a closer look at
the circumstances under which it is printed before presenting errors to
users.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
If RTS/CTS protection is needed for HT, wait until get operational
notification from mac80211, then inform uCode to switch to RTS/CTS
through RXON command.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When resuming from hibernate or suspend,
the status of the rfkill switch isn't
known since it might have been toggled
while the system was asleep. Therefore,
we need to read out the status at resume
time to make sure the system knows about
an up-to-date status.
Reported-by: Mark Tung <mark.y.tung@intel.com>
Tested-by: Mark Tung <mark.y.tung@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
The rate table in the bcast LQ is computed only when the station is
allocated, and chooses the lowest rate for the band. Because of when this
occurs, this is the 2.4 GHz band and uses the 0x420a (CCK, 1 Mbps) rate. In 5 GHz
beaconing mode, this rate will prevent beacons from being sent and any other
packets from being received.
We can fix this by re-initializing the bcast station's LQ command when the
channel is changed.
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
For some devices, especially the upcoming new devices, the plcp error
rate is different. Before the correct error rate can be determine, also
for the debugging purpose; add the mechanism to disable plcp error checking
which cause radio reset happen.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Different devices have different calibration requirement,
some need DC calibration and some don't; make it a cfg parameter
for easy management.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This bit need to be set for both RTS/CTS or CTS-to-self protection, if
CTS-to-self is used, then uCode will check the RXON_FLG_SELF_CTS_EN
status. Change the name from TX_CMD_FLG_RTS_CTS_MSK to TX_CMD_FLAG_PROT_REQUIRE_MSK
to match the behavior of the bit setting.
Also update comments to reflect which hardware uses which of the TX command
flags.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
When building tx command, always set TX_CMD_FLAG_PROT_REQUIRE_MSK
for 5000 series and up.
Without setting this bit the firmware will not examine the RTS/CTS setting
and thus not send traffic with the appropriate protection. RTS/CTS is is
required for HT traffic in a noisy environment where, without this setting,
connections will stall on some hardware as documented in the patch that
initially attempted to address this:
commit 1152dcc28c
Author: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Date: Fri Jan 15 13:42:58 2010 -0800
iwlwifi: Fix throughput stall issue in HT mode for 5000
Similar to 6000 and 1000 series, RTS/CTS is the recommended
protection mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
For 3945 and 4965, different flags are used for RTS/CTS or CTS-to-Self
protection.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke multicast. The reason, it turns out, is that
the code previously checked if ALLMULTI _changed_,
which the new code no longer did, and normally it
_never_ changes. Had somebody changed it manually,
the code prior to my patch there would have been
broken already.
The reason is that we always, unconditionally, ask
the device to pass up all multicast frames, but the
new code made it depend on ALLMULTI which broke it
since now we'd pass up multicast frames depending
on the default filter in the device, which isn't
necessarily what we want (since we don't program it
right now).
Fix this by simply not checking allmulti as we have
allmulti behaviour enabled already anyway.
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Tested-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace EFX_ERR() with netif_err(), EFX_INFO() with netif_info(),
EFX_LOG() with netif_dbg() and EFX_TRACE() and EFX_REGDUMP() with
netif_vdbg().
Replace EFX_ERR_RL(), EFX_INFO_RL() and EFX_LOG_RL() using explicit
calls to net_ratelimit().
Implement the ethtool operations to get and set message level flags,
and add a 'debug' module parameter for the initial value.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all PHY IDs to brcmphy.h header for completeness and unification of code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move ath9k_ps_wakeup() down just before accessing hw registers.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possbile that the transmission of paprd test frame
might not get completed in 100ms if tx is stuck. Freeing
this skb upon timeout in ath_paprd_calibrate() will result
in accessing already freed memory when the associated pending
buffer is drained in txq. This patch fixes this issue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW crypto in rt2500usb does not seem to support keys with different ciphers,
which breaks TKIP+AES mode. Fall back to software encryption to fix it.
This should fix long-standing problems with rt2500usb and WPA, such as:
http://rt2x00.serialmonkey.com/phpBB/viewtopic.php?f=4&t=4834https://bugzilla.redhat.com/show_bug.cgi?id=484888
Also tested that it does not break WEP, TKIP-only and AES-only modes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
