The datasheets for BCM20702 and BCM43438 both have power up time
sequence graphs, however they are slightly different. Both chips
also have an internal power-on-reset, which holds the chip in reset
for a short time after the regulators are enabled.
For the BCM20702, the time period from when the regulators are enabled,
until the chip settles and comes out of sleep state, is 6564 ~ 8171 us.
For the BCM43438, the graph only shows the time period from when the
regulators are enabled until the chip responds by driving the host's
CTS line low, assuming the host has already driven its RTS line low.
This is shown to be 6.5 sleep cycles, with the sleep clock at 32.768
kHz. This is around 2 ms.
Wait a full 10 ms after the regulators are enabled to account for signal
rising times.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
Model these two as regulator supplies, and let the driver manage them
in the same way as it does the clock supply.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers support a secondary LPO clock at
32.768 kHz. This external clock provides low power timing, and also
a way to detect the frequency of the main reference clock. On many
designs without NVRAM and a non-default reference clock, this must
be used or the controller will not function correctly.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Originally the device tree binding only specified one clock reference,
with the name "extclk". The driver simply retrieves the clock without
bothering to specify a name.
Since we added a second clock to the binding, we need to fetch the
clocks by name now. First we try the new name "txco", then fall back
to the old name "extclk", and finally try retrieving a clock without
using any name, to cover any instances where a bad device tree or
firmware worked by accident.
In the last case, we should take care that we don't get the same
clock twice when we add support for the "lpo" clock.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The driver currently checks the clk pointer for an error condition, as
returned by clk_get, before every invocation of the clk consumer API.
This is redundant if the goal is simply to ignore the errors, thereby
making the clk optional. The clk consumer API already checks if the
pointer is NULL or not.
Simplify the code a bit by assigning NULL to the clk pointer if the
error condition is one we want to ignore, which is every error except
deferred probing.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
On some systems that actually have the bluetooth controller wired up
with an extra clock signal, it's possible the bluetooth controller
probes before the clock provider. clk_get would return a defer probe
error, which was not handled by this driver.
Handle this properly, so that these systems can work reliably.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM4330 is a 802.11 a/b/g/n WiFi + Bluetooth 4.0 chip from Broadcom.
It is found in the Ampak AP6330 WiFi+BT module. The partiular one I have
identifies as BCM4330B1 for Bluetooth and BCM4330/4 for WiFi.
It is unclear if the AP6330 module uses this revision of the BCM4330, or
if there are multiple revisions. The module does not have revision
markings. This patch elects to use just BCM4330 for the compatible
string.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The BCM20702A1 is a Bluetooth 4.0 chip from Broadcom. It is found in the
Ampak AP6210 WiFi+BT module, identified from the read verbose config info
command response. However the Bluetooth firmware provided by vendors uses
the name BCM20710. This patch elects to use the chip ID returned by the
chip for the compatible string.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
This patch adds properties for the two so we can describe the power
supply relationships.
Reviewed-by: Rob Herring <robh@kernel.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Broadcom Bluetooth controllers can take up to two external clocks:
an external frequency reference, substituting the main crystal, and a
LPO clock at 32.768 kHz substituting the internal LPO clock.
In particular, the external LPO clock must be used when the controller
does not have NVRAM connected, and the main reference frequency is not
the default 20 MHz. This is described in detail in the datasheet.
The original "extclk" clock name is ambiguous as to which of these it
refers to, and some designs might even require both.
This patch deprecates the existing name, and adds "txco" and "lpo".
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This is one of only two files that initialize a semaphore to a negative
value. We don't really need the two semaphores here at all, but can do
the same thing in more conventional and more effient way, by using a
single waitqueue and an atomic thread counter.
This gets us a little bit closer to eliminating classic semaphores from
the kernel. It also fixes a corner case where we fail to continue after
one of the threads fails to start up.
An alternative would be to use a split kthread_create()+wake_up_process()
and completely eliminate the separate synchronization.
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far phy_error() silently stops the PHY state machine. If the network
driver doesn't inform about a MDIO error then the user may wonder why
his network is down. Let's print the stack trace to facilitate search
for the root cause of the error.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers phy_is_started() and __phy_is_started() to avoid open-coded
checks whether PHY has been started. To make the check easier move
PHY_HALTED before PHY_UP in enum phy_state. Further improvements:
phy_start_aneg():
Return -EBUSY and print warning if function is called from a non-started
state (DOWN, READY, HALTED). Better check because function is exported
and drivers may use it incorrectly.
phy_interrupt():
Return IRQ_NONE also if state is DOWN or READY. We should never receive
an interrupt in one of these states, but better play safe.
phy_stop():
Just return and print a warning if PHY is in a non-started state.
This warning should help to identify drivers with unbalanced calls to
phy_start() / phy_stop().
phy_state_machine():
Schedule state machine run only if PHY is in a started state.
E.g. if state is READY we don't need the state machine, it will be
started by phy_start().
v2:
- don't use __func__ within phy_warn_state
v3:
- use WARN() instead of printing error message to facilitate debugging
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a workaround to restart the phylib state machine in case of a
MDIO access timeout. Seems it was introduced to deal with the
consequences of a too small MDIO timeout. See also commit message of
c3b084c24c ("net: fec: Adjust ENET MDIO timeouts") which increased
the timeout value later. Due to the later timeout value fix it seems
to be safe to remove the workaround.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two statements that are indented too much by one space each,
fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() function sets all modes that are
supported by a given PPv2 port. A recent change made all ports to
advertise they support 10G modes in certain cases. This is not true,
as only the port #0 can do so. This patch fixes it.
Fixes: 01b3fd5ac9 ("net: mvpp2: fix detection of 10G SFP modules")
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some guests OSes (including Windows 10) write to MSR 0xc001102c
on some cases (possibly while trying to apply a CPU errata).
Make KVM ignore reads and writes to that MSR, so the guest won't
crash.
The MSR is documented as "Execution Unit Configuration (EX_CFG)",
at AMD's "BIOS and Kernel Developer's Guide (BKDG) for AMD Family
15h Models 00h-0Fh Processors".
Cc: stable@vger.kernel.org
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Reported by syzkaller:
CPU: 1 PID: 5962 Comm: syz-executor118 Not tainted 4.20.0-rc6+ #374
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:kvm_apic_hw_enabled arch/x86/kvm/lapic.h:169 [inline]
RIP: 0010:vcpu_scan_ioapic arch/x86/kvm/x86.c:7449 [inline]
RIP: 0010:vcpu_enter_guest arch/x86/kvm/x86.c:7602 [inline]
RIP: 0010:vcpu_run arch/x86/kvm/x86.c:7874 [inline]
RIP: 0010:kvm_arch_vcpu_ioctl_run+0x5296/0x7320 arch/x86/kvm/x86.c:8074
Call Trace:
kvm_vcpu_ioctl+0x5c8/0x1150 arch/x86/kvm/../../../virt/kvm/kvm_main.c:2596
vfs_ioctl fs/ioctl.c:46 [inline]
file_ioctl fs/ioctl.c:509 [inline]
do_vfs_ioctl+0x1de/0x1790 fs/ioctl.c:696
ksys_ioctl+0xa9/0xd0 fs/ioctl.c:713
__do_sys_ioctl fs/ioctl.c:720 [inline]
__se_sys_ioctl fs/ioctl.c:718 [inline]
__x64_sys_ioctl+0x73/0xb0 fs/ioctl.c:718
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The reason is that the testcase writes hyperv synic HV_X64_MSR_SINT14 msr
and triggers scan ioapic logic to load synic vectors into EOI exit bitmap.
However, irqchip is not initialized by this simple testcase, ioapic/apic
objects should not be accessed.
This patch fixes it by also considering whether or not apic is present.
Reported-by: syzbot+39810e6c400efadfef71@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
nested_get_vmcs12_pages() processes the posted_intr address in vmcs12. It
caches the kmap()ed page object and pointer, however, it doesn't handle
errors correctly: it's possible to cache a valid pointer, then release
the page and later dereference the dangling pointer.
I was able to reproduce with the following steps:
1. Call vmlaunch with valid posted_intr_desc_addr but an invalid
MSR_EFER. This causes nested_get_vmcs12_pages() to cache the kmap()ed
pi_desc_page and pi_desc. Later the invalid EFER value fails
check_vmentry_postreqs() which fails the first vmlaunch.
2. Call vmlanuch with a valid EFER but an invalid posted_intr_desc_addr
(I set it to 2G - 0x80). The second time we call nested_get_vmcs12_pages
pi_desc_page is unmapped and released and pi_desc_page is set to NULL
(the "shouldn't happen" clause). Due to the invalid
posted_intr_desc_addr, kvm_vcpu_gpa_to_page() fails and
nested_get_vmcs12_pages() returns. It doesn't return an error value so
vmlaunch proceeds. Note that at this time we have a dangling pointer in
vmx->nested.pi_desc and POSTED_INTR_DESC_ADDR in L0's vmcs.
3. Issue an IPI in L2 guest code. This triggers a call to
vmx_complete_nested_posted_interrupt() and pi_test_and_clear_on() which
dereferences the dangling pointer.
Vulnerable code requires nested and enable_apicv variables to be set to
true. The host CPU must also support posted interrupts.
Fixes: 5e2f30b756 "KVM: nVMX: get rid of nested_get_page()"
Cc: stable@vger.kernel.org
Reviewed-by: Andy Honig <ahonig@google.com>
Signed-off-by: Cfir Cohen <cfir@google.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If you register a kvm_coalesced_mmio_zone with '.pio = 0' but then
unregister it with '.pio = 1', KVM_UNREGISTER_COALESCED_MMIO will try to
unregister it from KVM_PIO_BUS rather than KVM_MMIO_BUS, which is a
no-op. But it frees the kvm_coalesced_mmio_dev anyway, causing a
use-after-free.
Fix it by only unregistering and freeing the zone if the correct value
of 'pio' is provided.
Reported-by: syzbot+f87f60bb6f13f39b54e3@syzkaller.appspotmail.com
Fixes: 0804c849f1 ("kvm/x86 : add coalesced pio support")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Peng Li says:
====================
net: hns3: code optimizations & bugfixes for HNS3 driver
This patchset includes bugfixes and code optimizations for the HNS3
ethernet controller driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When caculating the SSU buffer, it first allocate tx and
rx private buffer, then the remaining buffer is for rx
shared buffer. The remaining buffer size should be at
least bigger than or equal to the shared_std, which is the
minimum shared buffer size required by the driver, but
currently if the remaining buffer size is equal to the
shared_std, it returns failure, which causes SSU buffer
allocation failure problem.
This patch fixes this problem by rounding up shared_std before
checking the the remaining buffer size bigger than or equal to
the shared_std.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects the buffer size set to SSU is aligned to
256 bytes, this patch aligns the buffer size to 256 byte using
roundup or rounddown function.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support of getting tx and dv buffer size through
firmware, because different version of hardware requires different
size of tx and dv buffer.
This patch also add dv_buf_size to tc' private buffer size even if
pfc is not enable for the tc.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver calls phy_connect_direct and registers hclge_mac_adjust_link
to synchronize mac speed and duplex from phy. It is better to
synchronize mac speed and duplex from phy when phy link up.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our phy does not support 1000M/half, this patch removes 1000M/half from
PHY_SUPPORTED_FEATURES.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
coalesce param updates every 100 napi times, it may update a little
late if ping test after a high rate flow, may over napi poll is called
100 times as ping test sends packets every second.
This patch updates coalesce param every second, instead with every
100 napi times. It can not update the param 100% in time, but the
lag time is very short.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hns3_nic_uninit_vector_data(), the procedure of uninitializing
the tqp_vector's IRQ has not set affinity_notify to NULL and changes
its init flag. This patch fixes it. And for simplificaton, local
variable tqp_vector is used instead of priv->tqp_vector[i].
Fixes: 424eb834a9 ("net: hns3: Unified HNS3 {VF|PF} Ethernet Driver for hip08 SoC")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing reset, it is unnecessary to get the hardware's default
configuration again, otherwise, the user's configuration will be
overwritten.
Fixes: 4ed340ab8f ("net: hns3: Add reset process in hclge_main")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hclge_reset() completes successfully, it should update the
last_reset_time, set reset_fail_cnt to 0, and set reset_type of
hnae3_ae_dev to HNAE3_NONE_RESET.
Also when hclgevf_reset() completes successfully, it should update
the last_reset_time, and set reset_type of hnae3_ae_dev to
HNAE3_NONE_RESET.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While doing DOWN, the calling of napi_disable() may not return, since the
napi_complete() in the hns3_nic_common_poll() will never be called when
HNS3_NIC_STATE_DOWN is set. So we need to call napi_complete() before
checking HNS3_NIC_STETE_DOWN.
Fixes: ff0699e04b ("net: hns3: stop napi polling when HNS3_NIC_STATE_DOWN is set")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the hclgevf_pci_reset(), it only uninitialize and initialize
the msi, so if the initialization fails, hclgevf_uninit_hdev()
does not need to uninitialize the msi, but needs to uninitialize
the pci, otherwise it will cause pci resource not free.
Fixes: 862d969a3a ("net: hns3: do VF's pci re-initialization while PF doing FLR")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hns3_get_vector_ring_chain() failed in the
hns3_nic_init_vector_data(), it should do the error handling instead
of return directly.
Also, cur_chain should be freed instead of chain and head->next should
be set to NULL in error handling of hns3_get_vector_ring_chain.
This patch fixes them.
Fixes: 73b907a083 ("net: hns3: bugfix for buffer not free problem during resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a server side socket is bound to an address, but not in the listening
state yet, incoming connection requests should receive a reset control
packet in response. However, the function used to send the reset
silently drops the reset packet if the sending socket isn't bound
to a remote address (as is the case for a bound socket not yet in
the listening state). This change fixes this by using the src
of the incoming packet as destination for the reset packet in
this case.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reviewed-by: Adit Ranadive <aditr@vmware.com>
Reviewed-by: Vishnu Dasa <vdasa@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-12-18
1) Fix error return code in xfrm_output_one()
when no dst_entry is attached to the skb.
From Wei Yongjun.
2) The xfrm state hash bucket count reported to
userspace is off by one. Fix from Benjamin Poirier.
3) Fix NULL pointer dereference in xfrm_input when
skb_dst_force clears the dst_entry.
4) Fix freeing of xfrm states on acquire. We use a
dedicated slab cache for the xfrm states now,
so free it properly with kmem_cache_free.
From Mathias Krause.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Three fixes: The t10-pi one is a regression from the 4.19 release, the
qla2xxx one is a 4.20 merge window regression and the bnx2fc is a very
old bug.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXBkYeCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishblqAQCN7IcX
hQZcCrtoq6UukGywBtchLangKpFYz96A6VfRqwEAoFDLY72Roi7fsC9Gpll/8Y8H
RmkqIhNzBTODO3L8fiE=
=KFU4
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three fixes: The t10-pi one is a regression from the 4.19 release, the
qla2xxx one is a 4.20 merge window regression and the bnx2fc is a very
old bug"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: t10-pi: Return correct ref tag when queue has no integrity profile
scsi: bnx2fc: Fix NULL dereference in error handling
Revert "scsi: qla2xxx: Fix NVMe Target discovery"
Ido Schimmel says:
====================
mlxsw: VXLAN and firmware flashing fixes
Patch #1 fixes firmware flashing failures by increasing the time period
after which the driver fails the transaction with the firmware. The
problem is explained in detail in the commit message.
Patch #2 adds a missing trap for decapsulated ARP packets. It is
necessary for VXLAN routing to work.
Patch #3 fixes a memory leak during driver reload caused by NULLing a
pointer before kfree().
Please consider patch #1 for 4.19.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
After a packet was decapsulated it is classified to the relevant FID
based on its VNI and undergoes L2 forwarding.
Unlike regular (non-encapsulated) ARP packets, Spectrum does not trap
decapsulated ARP packets during L2 forwarding and instead can only trap
such packets in the underlay router during decapsulation.
Add this missing packet trap, which is required for VXLAN routing when
the MAC of the target host is not known.
Fixes: b02597d513 ("mlxsw: spectrum: Add NVE packet traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the firmware flash process, some of the EMADs get timed out, which
causes the driver to send them again with a limit of 5 retries. There are
some situations in which 5 retries is not enough and the EMAD access fails.
If the failed EMAD was related to the flashing process, the driver fails
the flashing.
The reason for these timeouts during firmware flashing is cache misses in
the CPU running the firmware. In case the CPU needs to fetch instructions
from the flash when a firmware is flashed, it needs to wait for the
flashing to complete. Since flashing takes time, it is possible for pending
EMADs to timeout.
Fix by increasing EMADs' timeout while flashing firmware.
Fixes: ce6ef68f43 ("mlxsw: spectrum: Implement the ethtool flash_device callback")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-12-18
1) Add xfrm policy selftest scripts.
From Florian Westphal.
2) Split inexact policies into four different search list
classes and use the rbtree infrastructure to store/lookup
the policies. This is to improve the policy lookup
performance after the flowcache removal.
Patches from Florian Westphal.
3) Various coding style fixes, from Colin Ian King.
4) Fix policy lookup logic after adding the inexact policy
search tree infrastructure. From Florian Westphal.
5) Remove a useless remove BUG_ON from xfrm6_dst_ifdown.
From Li RongQing.
6) Use the correct policy direction for lookups on hash
rebuilding. From Florian Westphal.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Over the years, xprt_connect_status() has been superseded by
call_connect_status(), which now handles all the errors that
xprt_connect_status() does and more. Since the latter converts
all errors that it doesn't recognise to EIO, then it is time
for it to be retired.
Reported-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
Ensure that we clear XPRT_CONNECTING before releasing the XPRT_LOCK so that
we don't have races between the (asynchronous) socket setup code and
tasks in xprt_connect().
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
When the socket is closed, we need to call xprt_disconnect_done() in order
to clean up the XPRT_WRITE_SPACE flag, and wake up the sleeping tasks.
However, we also want to ensure that we don't wake them up before the socket
is closed, since that would cause thundering herd issues with everyone
piling up to retransmit before the TCP shutdown dance has completed.
Only the task that holds XPRT_LOCKED needs to wake up early in order to
allow the close to complete.
Reported-by: Dave Wysochanski <dwysocha@redhat.com>
Reported-by: Scott Mayhew <smayhew@redhat.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Tested-by: Chuck Lever <chuck.lever@oracle.com>
When disabling HE due to the lack of HT/VHT, do it
at an earlier stage to avoid advertising HE capabilities IE.
Also, at this point, no need to check if AP supports HE, since
it is already checked earlier (in ieee80211_prep_channel).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Up until now, the IEEE80211_STA_DISABLE_HE flag was set only based
on whether the AP has advertised HE capabilities.
This flag should be set also if STA does not support HE
(regardless of the AP support).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Similar to WMM IE, if MU_EDCA IE parameters changed (or ceased to exist)
tell the Driver about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
HE Operation element has changed in 11ax D3.0. Update the fields
accordingly.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
