The TC358743 does not support more than 4 data lanes. Check that the
lane count is valid.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When I was supporting Rpi Camera Module on the ASUS Tinker board,
I found this driver have some issues with rockchip's mipi-csi driver.
It didn't place clock lane in LP-11 state before performing
D-PHY initialisation.
>From our experience, on some OV sensors,
LP-11 state is not achieved while BIT(5)-0x4800 is cleared.
So let's set BIT(5) and BIT(0) both while not streaming, in order to
coax the clock lane into LP-11 state.
0x4800 : MIPI CTRL 00
BIT(5) : clock lane gate enable
0: continuous
1: none-continuous
BIT(0) : manually set clock lane
0: Not used
1: used
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Reviewed-by: Luis Oliveira <lolivei@synopsys.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the ov7670_s_power function which is responsible for
manipulating the power dowm mode through the PWDN pin and the reset
operation through the RESET pin, and keep it powered at all times.
[sakari.ailus@linux.intel.com: set pwdn_gpio direction only once]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the get_fmt callback, also enable V4L2_SUBDEV_FL_HAS_DEVNODE flag
to make this subdev has device node.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the media entity pads initialization.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver adds support for the Tegra CEC IP. It is based on the
NVIDIA drivers/misc/tegra-cec driver in their 3.10 kernel.
This has been converted to the CEC framework and cleaned up.
Tested with my Jetson TK1 board. It has also been tested with the
Tegra X1 in an embedded product.
Note of warning for the Tegra X2: this SoC supports two HDMI outputs,
but only one CEC adapter and the CEC bus is shared between the
two outputs. This is a design mistake and the CEC adapter can
control only one HDMI output. Never hook up both HDMI outputs
to the CEC bus in a hardware design: this is illegal as per the
CEC specification.
The CEC bus can be shared between multiple inputs and zero or one
outputs, but not between multiple outputs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The imx274 is a Sony CMOS image sensor that has 1/2.5 image size.
It supports up to 3840x2160 (4K) 60fps, 1080p 120fps. The interface
is 4-lane MIPI CSI-2 running at 1.44Gbps each.
This driver has been tested on Xilinx ZCU102 platform with a Leopard
LI-IMX274MIPI-FMC camera board.
Support for the following features:
-Resolutions: 3840x2160, 1920x1080, 1280x720
-Frame rate: 3840x2160 : 5 – 60fps
1920x1080 : 5 – 120fps
1280x720 : 5 – 120fps
-Exposure time: 16 – (frame interval) micro-seconds
-Gain: 1x - 180x
-VFLIP: enable/disabledrivers/media/i2c/imx274.c
-Test pattern: 12 test patterns
Signed-off-by: Leon Luo <leonl@leopardimaging.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TC358743 is an HDMI to MIPI CSI2-2 bridge.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
We can remove the check for if "state->cec_adap" is NULL. The
cec_allocate_adapter() function never returns NULL and also we verified
that "state->cec_adap" is an error pointer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make vb2_ops const as they are only stored in the const field of a
vb2_queue structure. Make the declarations const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make vb2_ops const as they are only stored in the const field of a
vb2_queue structure. Make the declarations const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only used in a copy operation in the file
referencing it. Make the declaration const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only passed to the const argument of the
function videobuf_queue_sg_init in the file referencing it.
Also, make the declaration in the header const.
Structure found using Coccinelle and changes done by hand.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
It should be "LP-11".
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Delete seven error messages for a failed memory allocation
- Adjust seven checks for null pointers
- Use common error handling code in tm6000_usb_probe()
- Adjust jump targets so that the function "kfree" will be always called
with a non-null pointer.
- Delete an initialisation for the local variable "dev"
which became unnecessary with this refactoring.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The kAPI cec-pin.h header also defined data structures that did
not belong here but were private to the CEC core code.
Split that part off into a cec-pin-priv.h header.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This addresses the wrong behavior of decoder stop command by
rewriting it. These new implementation enqueue an empty buffer
on the decoder input buffer queue to signal end-of-stream. The
client should stop queuing buffers on the V4L2 Output queue
and continue queuing/dequeuing buffers on Capture queue. This
process will continue until the client receives a buffer with
V4L2_BUF_FLAG_LAST flag raised, which means that this is last
decoded buffer with data.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
In case of error, the function platform_device_register_data() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes wrongly filled bytesused field of v4l2_plane structure
by include data_offset in the plane, Also fill data_offset and
bytesused for capture type of buffers only.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To improve the readability of code, split the format array into two,
one for the format description, other for the register configuration.
Meanwhile, add the flag member to indicate the format can be achieved
from the sensor or be produced by the controller, and rename members
related to the register configuration.
Also add more formats support: GREY, ARGB444, ARGB555 and ARGB32.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove the memeber *config from the isc_subdev_entity struct,
the member is useless afterward.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
To meet the relationship, enable the HCLOCK and ispck during the
device probe, "isc_pck frequency is less than or equal to isc_ispck,
and isc_ispck is greater than or equal to HCLOCK."
Meanwhile, call the pm_runtime_enable() in the right place.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A software write operation to the ISC_CLKEN or ISC_CLKDIS register
requires double clock domain synchronization and is not permitted
when the ISC_SR.SIP is asserted. So add the .prepare and .unprepare
ops to make sure the ISC_CLKSR.SIP is unasserted before the write
operation to the ISC_CLKEN or ISC_CLKDIS register.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the spin lock for the clock enable and disable operations.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't currently harmful.
However, for some features it is necessary to instrument reads and
writes separately, which is not possible with ACCESS_ONCE(). This
distinction is critical to correct operation.
It's possible to transform the bulk of kernel code using the Coccinelle
script below. However, this doesn't handle comments, leaving references
to ACCESS_ONCE() instances which have been removed. As a preparatory
step, this patch converts the DVB ringbuffer code and comments to use
{READ,WRITE}_ONCE() consistently.
----
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-6-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This change will fix an issue with dma_free size found with
DMA API debug enabled.
Signed-off-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.13 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of relying on a mix of runtime PM and the s_power() callback, drop
the s_power() callback altogether and use runtime PM solely.
As device access is required during device power-on and power-off
sequences, runtime PM alone cannot tell whether the device is available.
Thus the "active" field is introduced in struct smiapp_sensor to tell
whether it is safe to write to the device.
Consequently there is no need to power on the device whenever a file
handle is open. This functionality is removed as well. The user may still
control the device power management through sysfs. Autosuspend remains
enabled, with 1 s delay.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use unlocked __v4l2_ctrl_handler_setup() in order to make the
control setup atomic.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* commit '3728e6a255b5': (904 commits)
Linux 4.14-rc5
x86/microcode: Do the family check first
locking/lockdep: Disable cross-release features for now
x86/mm: Flush more aggressively in lazy TLB mode
mm, swap: use page-cluster as max window of VMA based swap readahead
mm: page_vma_mapped: ensure pmd is loaded with READ_ONCE outside of lock
kmemleak: clear stale pointers from task stacks
fs/binfmt_misc.c: node could be NULL when evicting inode
fs/mpage.c: fix mpage_writepage() for pages with buffers
linux/kernel.h: add/correct kernel-doc notation
tty: fall back to N_NULL if switching to N_TTY fails during hangup
Revert "vmalloc: back off when the current task is killed"
mm/cma.c: take __GFP_NOWARN into account in cma_alloc()
scripts/kallsyms.c: ignore symbol type 'n'
userfaultfd: selftest: exercise -EEXIST only in background transfer
mm: only display online cpus of the numa node
mm: remove unnecessary WARN_ONCE in page_vma_mapped_walk().
mm/mempolicy: fix NUMA_INTERLEAVE_HIT counter
include/linux/of.h: provide of_n_{addr,size}_cells wrappers for !CONFIG_OF
mm/madvise.c: add description for MADV_WIPEONFORK and MADV_KEEPONFORK
...
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZ5RRxAAoJEAhfPr2O5OEVa2oQAJ7TeRcV/a76xSPb3hN/T6VL
EPpKZYaP2BjvmqDy9p3GbN0/Jp+ltDD7HhzQQHUDMMjkouyhtLRONBmi21YcNOvH
wGW2qTYqMis5KBDFPZ6sHEGLpZBS6c8Gsz+X6pGh6OGIQVsyEGSaaE8m6zCGj4qz
pfNq15Zax/JU1zhTFs/iO9IzG9aW2Q++p3Tgs5OdPIOua3hwontTbKODzhFgUDip
yjvYtD3rF1ftftxq3kPunrywsv1BvHnX2E1TVKAZoFDpd0Eo2Nud922EBRLTxAO3
w1xdI9fLMi1BnJYx1VdQ0onDi8muVGXcIrXVvh6eA4NPsGY2AFXluUSm7zBCpxXY
jDGTyIa+pLxr9y03zP5Nx9IHcMFApz1LzDpKaBWKCKEu3EB/9jGtY7Vrc0cHdeDa
on93vVMHu+80Uxw4txHBJuYhXNPakz0n99zhZbbcdpHLyTM7aINXNa37IAp7tNeu
5nCSJ2FWrNgFRC+3avvbGSfJBA12QJgyEvuEHW0bTttSDVxh14XzGz+C1lx960qc
EbIQzPJxtwLSZ4y7OfDGBPWTrql5C0SQo9Z+K6S8reJsoILTCYZRXQaB1u+D+ff/
zfLCYTbRwabUre9C/jeT+XrT+KJyZ+huGMs2HMslGauRbWuUwgCv86WuVkp7httz
HtzQSKK6s5iWh2H9T2x0
=VOJs
-----END PGP SIGNATURE-----
Merge tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"Core fixes:
- cec: Respond to unregistered initiators, when applicable
- dvb_frontend: only use kref after initialized
Driver-specific fixes:
- qcom, camss: Make function vfe_set_selection static
- qcom: VIDEO_QCOM_CAMSS should depend on HAS_DMA
- s5p-cec: add NACK detection support
- media: staging/imx: Fix uninitialized variable warning
- dib3000mc: i2c transfers over usb cannot be done from stack
- venus: init registered list on streamoff"
* tag 'media/v4.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: dvb_frontend: only use kref after initialized
media: platform: VIDEO_QCOM_CAMSS should depend on HAS_DMA
media: cec: Respond to unregistered initiators, when applicable
media: s5p-cec: add NACK detection support
media: staging/imx: Fix uninitialized variable warning
media: qcom: camss: Make function vfe_set_selection static
media: venus: init registered list on streamoff
media: dvb: i2c transfers over usb cannot be done from stack
The script “checkpatch.pl” pointed information out like the following.
Comparison to NULL could be written...
Thus fix the affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Omit an extra message for a memory allocation failure in s5p_mfc_probe()
function. This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The hardware rotation limits of gsc depends on SOC (Exynos
5250/5420/5433). Distinguish them and add them to the driver data.
[s.nawrocki@samsung.com: corrected num_entities in 5420 variant data]
Signed-off-by: Hoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rockchip RGA is a separate 2D raster graphic acceleration unit. It
accelerates 2D graphics operations, such as point/line drawing, image
scaling, rotation, BitBLT, alpha blending and image blur/sharpness
The driver supports various operations from the rendering pipeline.
- copy
- fast solid color fill
- rotation
- flip
- alpha blending
The code in rga-hw.c is used to configure regs according to operations
The code in rga-buf.c is used to create private mmu table for RGA.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
changeset 6bbf7a855d ("media: dvbdev: convert DVB device types into an enum")
added a new warning on gcc 6:
>> drivers/media/dvb-core/dvbdev.c:86:1: warning: control reaches end of non-void function [-Wreturn-type]
That's because gcc is not smart enough to see that all types are
present at the switch. Also, the current code is not too optimized.
So, replace it to a more optimized one, based on a static table.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6bbf7a855d ("media: dvbdev: convert DVB device types into an enum")
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix a bunch of coding style issues found by checkpatch on the
part of the code that the previous patches touched.
WARNING: please, no space before tabs
+ * ^I^Icallback.$
ERROR: space required before the open parenthesis '('
+ switch(cmd) {
WARNING: line over 80 characters
+ err = dtv_property_process_get(fe, &getp, tvp + i, file);
WARNING: line over 80 characters
+ err = fe->ops.diseqc_recv_slave_reply(fe, (struct dvb_diseqc_slave_reply*) parg);
ERROR: "(foo*)" should be "(foo *)"
+ err = fe->ops.diseqc_recv_slave_reply(fe, (struct dvb_diseqc_slave_reply*) parg);
WARNING: line over 80 characters
+ err = fe->ops.read_signal_strength(fe, (__u16 *) parg);
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The functions used on dvb_demux.h are largely used on DVB drivers.
Yet, none of them are documented.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are three structs defined inside dvb_demux.h. None
of them are currently documented.
Add documentation for them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Simplify the get property handling and move it to the existing
code at dtv_property_process_get() directly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since all properties in the func dtv_property_process_set() use
at most 4 bytes arguments, change the code to pass
u32 cmd and u32 data as function arguments, instead of passing a
pointer to the entire struct dtv_property *tvp.
Instead of having a generic dtv_property_dump(), added its own
properties debug logic in the dtv_property_process_set().
Signed-off-by: Satendra Singh Thakur <satendra.t@samsung.com>
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of using an integer to represent it, use boolean,
as this better describes what this field really means.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The struct dvb_demux_filter.doneq is a boolean.
Mark it as such, as it helps to understand what it does.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kernel-doc allows documenting enums. Also, it makes clearer
about the meaning of each field on structures.
So, convert DMX_STATE_* to an enum.
While here, get rid of the unused DMX_STATE_SET.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
kernel-doc allows documenting enums. Also, it makes clearer
about the meaning of each field on structures.
So, convert DMX_TYPE_* to an enum.
While here, get rid of the unused DMX_TYPE_PES.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Several minor adjustments at the kernel-doc markups:
- some syntax fixes;
- some cross-references;
- add cross-references for the mentioned ioctls;
- some constants marked as such.
No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several functions at the dvbdev that are common to all
digital TV device nodes with aren't documented.
Add documentation for them. No functional changes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Enums can be documented via kernel-doc. So, convert the
DVB_DEVICE_* macros to an enum.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several problems with regards to the return of
FE_SET_PROPERTY. The original idea were to return per-property
return codes via tvp->result field, and to return an updated
set of values.
However, that never worked. What's actually implemented is:
- the FE_SET_PROPERTY implementation doesn't call .get_frontend
callback in order to get the actual parameters after return;
- the tvp->result field is only filled if there's no error.
So, it is always filled with zero;
- FE_SET_PROPERTY doesn't call memdup_user() nor any other
copy_to_user() function. So, any changes to the properties
will be lost;
- FE_SET_PROPERTY is declared as a write-only ioctl (IOW).
While we could fix the above, it could cause regressions.
So, let's just assume what the code really does, updating
the documentation accordingly and removing the logic that
would update the discarded tvp->result.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Two readonly ioctls can't be allowed if the frontend device
is opened in read only mode. Explain why.
Reviewed by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are too much tabs on several properties, for no good
reason. That sounds confusing while reading the struct, so
adjust them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, I guess the idea was to use state in order to
allow an autofush logic. However, in the current code, it is
used only for debug messages, on a poor man's solution, as
there's already a debug message to indicate when the properties
got flushed.
So, just get rid of it for good.
Reviewed-by: Shuah Khan <shuahkg@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, there are two handlers for ioctls:
- dvb_frontend_ioctl_properties()
- dvb_frontend_ioctl_legacy()
Despite their names, both handles non-legacy DVB ioctls.
Besides that, there's no reason why to not handle all ioctls
on a single handler function.
So, merge them into a single function (dvb_frontend_handle_ioctl)
and reorganize the ioctl's to indicate what's the current DVB
API and what's deprecated.
Despite the big diff, the handling logic for each ioctl is the
same as before.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use a switch() on this function, just like on other ioctl
handlers and handle parameters inside each part of the
switch.
That makes it easier to integrate with the already existing
ioctl handler function.
Reviewed-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Only lg2160 implement gets_property, but there's no need for that,
as no other driver calls this callback, as get_frontend() does the
same, and set_frontend() also calls lg2160 get_frontend().
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This callback is not actually doing anything but making it to
return an error depending on the DTV frontend command. Well,
that could break userspace for no good reason, and, if needed,
should be implemented, instead, at set_frontend() callback.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The stv6110 has a weird code that checks if get_property
and set_property ioctls are defined. If they're, it initializes
a "srate" var from properties cache. Otherwise, it sets to
15MBaud, with won't make any sense.
Thankfully, it seems that someone else discovered the issue in
the past, as "srate" is currently not used anywhere!
So, get rid of that really weird dead code logic.
Reported-by: Honza Petrous <jpetrous@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver doesn't implement support for set_property(). Yet,
it implements a boilerplate for it. Get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by Laurent, when a DVB frontend need to register
two drivers (e. g. a tuner and a demod), if the second driver
fails to register (for example because it was not compiled),
the error handling logic frees the frontend by calling
dvb_frontend_detach(). That used to work fine, but changeset
1f862a68df ("[media] dvb_frontend: move kref to struct dvb_frontend")
added a kref at struct dvb_frontend. So, now, instead of just
freeing the data, the error handling do a kref_put().
That works fine only after dvb_register_frontend() succeeds.
While it would be possible to add a helper function that
would be initializing earlier the kref, that would require
changing every single DVB frontend on non-trivial ways, and
would make frontends different than other drivers.
So, instead of doing that, let's focus on the real issue:
only call kref_put() after kref_init(). That's easy to
check, as, when the dvb frontend is successfuly registered,
it will allocate its own private struct. So, if such
struct is allocated, it means that it is safe to use
kref_put(). If not, then nobody is using yet the frontend,
and it is safe to just deallocate it.
Fixes: 1f862a68df ("[media] dvb_frontend: move kref to struct dvb_frontend")
Reported-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The tango HW IR decoder supports NEC, RC-5, RC-6 protocols.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add a keymap for the Sigma Designs Vantage (dev board) remote control.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the kernel is built without device tree, this driver cannot be
used and without gpiolib it cannot control any gpio pin.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When receiving an nec repeat, rc_repeat() is called and then rc_keydown()
with the last decoded scancode. That last call is redundant.
Fixes: 265a2988d2 ("media: rc-core: consistent use of rc_repeat()")
Cc: <stable@vger.kernel.org> # v4.14
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are no users of this functionality (ir-lirc-codec.c has its own
implementation and lirc_zilog.c doesn't use it) so remove it.
This only affects users of the lirc kapi, not rc-core drivers.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 0-day robot reports:
drivers/media/rc/gpio-ir-recv.c: In function 'gpio_ir_recv_irq':
>> drivers/media/rc/gpio-ir-recv.c:38:8: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]
Fixes: eed008e605 ("[media] media: rc: gpio-ir-recv: use gpiolib API")
For some reason only partial patch was applied. Also include
gpio/consumer.h otherwise compile test fails.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Sean Young <sean@mess.org>
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The clock control is not explicitly controlled by the driver in two cases:
ACPI based systems and when the clock is part of the power sequence of the
camera module.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Obtain the clock rate from the clock framework if it's not available
through DT. The assumption is that the parent device (camera module)
defines the rate as clock control is a part of the power on and power off
sequences --- which are camera module specific.
Also use the clock rate from DT if no clock is provided.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The external clock frequency was set by the driver but the obtained
frequency was never verified. Do that.
Being able to obtain the exact frequency is important as the value is used
for PLL calculations which may result in frequencies that violate the PLL
tree limits.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The error handling code in smiapp_power_on() returned in case of a failed
I2C write instead of cleaning up the mess. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ov13858 contained a 64-bit division. Use do_div() for calculating it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, with crop (0, 0), (4255, 3167), VTS < 0xC9E was resulting in
blank frames sometimes. This appeared as video flickering. But we need VTS
< 0xC9E to get ~30fps.
Omni Vision recommends to use crop (0,8), (4255, 3159) for 4224x3136. With
this crop, VTS 0xC8E is supported and yields ~30fps.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Calculate pixel-rate at run time instead of compile time.
Instead of using hardcoded pixels-per-line, extract it from current sensor
mode.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't populate the array reset_seq on the stack, instead make it
static. Makes the object code smaller by over 50 bytes:
Before:
text data bss dec hex filename
11737 6000 64 17801 4589 drivers/media/i2c/ov2640.o
After:
text data bss dec hex filename
11582 6096 64 17742 454e drivers/media/i2c/ov2640.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The active and has_no_links arrays will overrun in
media_entity_pipeline_start() if there's an entity which has more than
MEDIA_ENTITY_MAX_PAD pads. Ensure in media_entity_init() that there are
fewer pads than that.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the specification of a data structure by pointer dereferences
as the parameter for the operator "sizeof" to make size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: merged similar patches]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Omit extra messages for memory allocation failures.
This issue was detected by using the Coccinelle software.
[mchehab@s-opensource.com: merged similar patches]
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, the sensor was not streaming after resume from suspend,
i.e. on S0->S3->S0 transition. Due to this, camera app preview appeared
as stuck.
Now, handle streaming state correctly in case of suspend-resume.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Current v4l2 focus ctrl step value of 16, limits the minimum granularity
of focus positions to 16. Setting this value as 1, enables more accurate
focus positions.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
devm_clk_get() may return different error codes other than -EPROBE_DEFER,
so it is better to return the real error code instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
v4l2_clk_get() may return different error codes other than -EPROBE_DEFER,
so it is better to return the real error code instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Previously, images were relatively darker due to non-optimal
settings for black target level and bias.
Now, use recommended settings for black target level and output bias
as default values. The same default settings apply to all the resolutions.
Given these recommeneded settings do not change dynamically, add these to
existing mode register settings.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If you have a control handler that does not contain any controls, then
currently calling VIDIOC_G/S/TRY_EXT_CTRLS with count == 0 will return
-EINVAL in the class_check() function.
This is not correct, there is no reason why this should return an error.
The purpose of setting count to 0 is to test if the ioctl can mix controls
from different control classes. And this is possible. The fact that there
are not actually any controls defined is another matter that is unrelated
to this test.
This caused v4l2-compliance to fail, so that is fixed with this patch applied.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only send HPD_LOW/HIGH event if the gpio actually changed value.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make sure to check that we actually have an Interface Association
Descriptor before dereferencing it during probe to avoid dereferencing a
NULL-pointer.
Fixes: e0d3bafd02 ("V4L/DVB (10954): Add cx231xx USB driver")
Cc: stable <stable@vger.kernel.org> # 2.6.30
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This converts to use setup_timer() to set callback and data, though it
doesn't look like this would have worked with timer checking enabled
since no init_timer() was ever called before.
Cc: Mats Randgaard <matrandg@cisco.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for 10 and 12 bit luma formats.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Support the 10 and 12 bit luma formats.
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Older compilers like gcc-4.6 may run into a case that returns
an uninitialized variable from rcar_drif_enable_rx() if that
function was ever called with an empty cur_ch_mask:
drivers/media/platform/rcar_drif.c:658:2: error: ‘ret’ may be used uninitialized in this function [-Werror=uninitialized]
Newer compilers don't have that problem as they optimize the
'ret' variable away and just return zero in that case.
This changes the function to return -EINVAL for this particular
failure, to make it consistent across all compiler versions.
In case gcc gets changed to report a warning for it in the
future, it's also a good idea to shut it up now.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82203
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make these const as they are not modified in the file referencing them.
They are only used when their function pointer fields invokes a
function and therefore none of the structure fields are getting modified.
Also, add a const to the declaration in the header.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't populate const arrays on the stack, instead make them
static. Makes the object code smaller by over 5200 bytes:
Before:
text data bss dec hex filename
58259 8880 128 67267 106c3 ov519.o
After:
text data bss dec hex filename
52155 9776 128 62059 f26b ov519.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The video standard was not mapped to the corresponding value of the
internal video standard in adv748x_afe_querystd, causing the wrong
video standard to be selected.
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
[Kieran: Obtain the std from the afe->curr_norm]
Signed-off-by: Simon Yuan <simon.yuan@navico.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace the specification of data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
ir_setkeytable() and ir_create_table() print the same debug message.
Delete the one in ir_setkeytable()
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Linus policy on Kconfig is that the default should be no
for all new devices. I.e the user rebuild a new kernel from an
old config should not by default get a larger kernel.
Fixes: b4c184e506 ("[media] media: reorganize the main Kconfig items")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Gpiolib API is preferred way to access gpios.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
gpio_ir_recv_platform_data are not used anywhere in kernel tree,
so remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There already is standard macro providing driver name, use it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use of devm_request_irq simplifies error unwinding and as
free_irq was the last user of driver remove function,
remove it too.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Requesting any context irq is not actually great idea since threaded
interrupt handler is run at too unpredictable time which turns
timing information wrong. Fix it by requesting regular interrupt.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use of devm_rc_register_device simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use of devm_gpio_request_one simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use of devm_rc_allocate_device simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use of devm_kzalloc simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using explicit struct device variable makes code a bit more readable.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't populate the const arrays vfd_packet6 and fp_packet on the
stack, instead make them static. Makes the object code smaller
by over 600 bytes:
Before:
text data bss dec hex filename
43794 17920 1024 62738 f512 drivers/media/rc/imon.o
After:
text data bss dec hex filename
42994 18080 1024 62098 f292 drivers/media/rc/imon.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Only the nec protocol is understood, but then it doesn't pass on
the full scancode and it ignores the nec repeats its own remote
sends, so holding buttons does not work.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This name is also stored in the input's device name, but that
is not available in TX only hardware (no input device).
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If the protocols of an rc device cannot be changed, ensure the sysfs
file is not writable.
This makes it possible to detect this from userspace, so ir-keytable
can deal with case without giving an error.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
"IR-receiver inside an USB DVB receiver" is not descriptive and we have
a proper name available.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rc scancode drivers without change_protocol should have all
protocols enabled at all time. This was only true for cec and
ir-kbd-i2c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The keymap is missing one key, and correct another.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This receiver only accepts nec16 messages, I've tried many other protocols
and they're all dropped.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make this const as it is only stored in the type field of a device
structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The use of two separate structs (lirc_dev aka lirc_driver and irctl) makes
it much harder to follow the proper lifetime of the various structs and
necessitates hacks such as keeping a copy of struct lirc_dev inside
struct irctl.
Merging the two structs means that lirc_dev can properly manage the
lifetime of the resulting struct and simplifies the code at the same time.
[mchehab@s-opensource.com: fix merge conflict]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Introduce two new functions so that the API for lirc_dev matches that
of the rc-core and input subsystems.
This means that lirc_dev structs are managed using the usual four
functions:
lirc_allocate_device
lirc_free_device
lirc_register_device
lirc_unregister_device
The functions are pretty simplistic at this point, later patches will put
more flesh on the bones of both.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
This is in preparation for the later patches which do away with
struct irctl entirely.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using the kernel-provided IDA simplifies the code and makes it possible
to remove the lirc_dev_lock mutex.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use the irctl mutex for all device operations and only use lirc_dev_lock
to protect the irctls array. Also, make sure that the device is alive
early in each fops function before doing anything else.
Since this patch touches nearly every line where the irctl mutex is
taken/released, it also renames the mutex at the same time (the name
irctl_lock will be misleading once struct irctl goes away in later
patches).
[mchehab@s-opensource.com: fix a merge conflict]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The "attached" member of struct irctl is a boolean value, so let the code
reflect that.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make setting chunk_size and buffer_size mandatory for drivers which
expect lirc_dev to allocate the lirc_buffer (i.e. ir-lirc-codec) and
don't set them in lirc-zilog (which creates its own buffer).
Also remove an unnecessary copy of chunk_size in struct irctl (the
same information is already available from struct lirc_buffer).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
By making better use of file->private_data in lirc_dev we can avoid
digging around in the irctls[] array, thereby simplifying the code.
External drivers need to use lirc_get_pdata() instead of mucking around
in file->private_data.
The newly introduced lirc_init_pdata() function isn't very elegant, but
it's a stopgap measure which can be removed once lirc_zilog is converted
to rc-core.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Replace calls to cdev_add() and device_add() with the cdev_device_add()
helper function.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
All users of lirc_register_driver() uses dynamic minor allocation,
therefore we can remove the ability to explicitly request a given number.
This changes the function prototype of lirc_unregister_driver() to also
take a struct lirc_driver pointer as the sole argument.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
If an error is generated, it is more logical to error out ASAP.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The help text should be indented by at least two spaces after the
'help' separator. This is both good practice and the media_build system
for building media drivers makes this assumption.
I went through all Kconfigs under drivers/media and fixed any bad help
sections. This makes it conform to the common practice and should fix
problems with 'make menuconfig' when using media_build. This is due to
a "WARNING" message that media_build can insert in the Kconfig and that
assumes the help text is indented by at least two spaces. If not, then the
Kconfig becomes invalid and 'make menuconfig' fails.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Thomas Kaiser <linux-dvb@kaiser-linux.li>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the distant past the adv7604 driver used private controls. In order
to access them the v4l-subdevX nodes were needed. Later the is_private
tag was removed in the adv7604 driver and the need for v4l-subdevX
device nodes disappeared.
Remove the creation of those device nodes from this driver.
Note: the cobalt card is only used inside Cisco and we never actually
used the v4l-subdevX nodes for anything. So this API change can be done
safely without breaking anything.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
max_width and max_height are swap with step_width and step_height.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
