This adds support for reading and writing date/time from/to ds1341 chip.
ds1341 chip has other features - alarms, input clock (can be used instead
of intercal oscillator for better accuracy), output clock ("square wave
generation"). However, not all of that is available at the same time.
Same chip pins, CLKIN/nINTA and SQW/nINTB, can be used either for
input/output clocks, or for alarm interrupts. Role of these pins on
particular board depends on hardware wiring.
We can add device tree properties that describe if each of pins is wired
as clock, or as interrupt, or left unconnected, and enable support for
corresponding functionality based on that. But that is cumbersome, requires
hardware for testing, and has to deal with bit enabling/disabling output
clock also affects which pins alarm interrupts are routed to.
Another factor is that there are hardware setups (i.e. ZII RDU2) that
power DS1341 from SuperCap, which makes power saving critical. For such
setups, kernel driver should leave register bits that control mentioned
pins in the state configured by bootloader.
Given all that, it was decided to limit support to "only date/time" for
now. That is enough for common use case. Full (and cumbersome)
implementation can be added later if ever needed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove member nvram_offset from struct ds1307 and use the value stored
in struct chip_desc directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out offset to struct chip_desc and remove it from struct ds1307.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out rtc_ops to struct chip_desc and use ds13xx_rtc_ops as default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out irq_handler to struct chip_desc and use ds1307_irq as default.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Change the usage of variable want_irq to reflect its name. Don't set
it to true in case wakeup is enabled but no interrupt number is given.
In addition set variable ds1307_can_wakeup_device if chip->alarm
is set only.
This allows to simplify the code and make it better understandable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of storing the trickle_charger_setup value in struct chip_desc
we can let function ds1307_trickle_init return it because it's used
in the probe function only.
This allows us to constify struct chip_desc variables in a next step.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Factor out the bbsqi bit to struct chip_desc.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The irq number is used in the probe function only, so we don't have
to store it in struct ds1307.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Current max_register setting breaks reading nvram on certain chips and
also reading the standard registers on RX8130 where register map starts
at 0x10.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 11e5890b53 "rtc: ds1307: convert driver to regmap"
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Commit 8b44f5be20 ("ARM: dts: armada: replace isil,irq2-can-wakeup-machine with wakeup-source property")
removed the last usage of "isil,irq2-can-wakeup-machine" almost
two years ago. So I think we can get rid of supporting this
legacy binding.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Instead of adding a binary sysfs attribute from the driver (which suffers
from a race condition as the attribute appears after the device), use the
core to register an nvmem device.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This removes a possible race condition and crash and allows for further
improvement of the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ds1308 variant is very similar to the already supported ds1338
variant, it have more debug registers and a square wave clock output.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver has lots of places with chip-specific code what doesn't
necessarily facilitate maintenance.
Let's describe chip-specific differences in century bit handling
in struct chip_desc to improve this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
After the switch to regmap we can now make use of regmap_update_bits
to simplify read/modify/write ops.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add support for yet another RTC chip, Epson RX8130CE. This time around,
the chip has slightly permutated registers and also the register starts
at 0x10 instead of 0x0 .
So far, we only support the RTC and NVRAM parts of the chip, Alarm and
Timer is not supported.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch extends the fixes for ds1337, ds1339, ds3231 in commit
8bc2a40730 ("rtc: ds1307: add support for the DT property
'wakeup-source'") to mcp794xx devices, so that those parts can similarly be
used as a wakeup source without an IRQ to the processor.
Tested on Raspberry Pi ZeroW with MCP79400.
Signed-off-by: David Lowe <dave-lowe@ntlworld.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch converts the ds1307 driver to using regmap. It's a rather
big patch and I can test with DS3231 only. With this chip it's
working fine.
I'd appreciate if people with other supported hardware could test as
well.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The m41t0 variant is very similar to the already supported m41t00
variant, with the notable exception of the oscillator fail bit.
The data sheet notes:
If the oscillator fail (OF) bit is internally set to a '1,' this
indicates that the oscillator has either stopped, or was stopped
for some period of time and can be used to judge the validity of
the clock and date data.
The bit will get cleared with a regular write of the system time,
so no changes are needed to clear it.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch enables ACPI support for rtc-ds1307 driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Intersil ISL12057 is a drop-in replacement for DS1337. It can be supported
by the ds1307 driver.
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add an option to properly support the century bit of ds1337 and compatibles
and ds1340.
Because the driver had a bug until now, it is not possible to switch users
to the fixed code directly as RTCs in the field will wrongly have the
century bit set.
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit d68778b80d ("rtc: initialize output parameter for read
alarm to "uninitialized"") there is no need to explicitly set
unsupported members to -1. So drop the respective assignments from
drivers.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The reset value of weekday is 0x1. This is wrong since
the reset values of the day/month/year make up to Jan 1 2001.
When computed weekday comes out to be Monday. On a scale
of 1-7(Sunday - Saturday) it should be 0x2. So we should not
be relying on the reset value.
Hence compute the wday using the current date/month/year values.
Check if reset wday is any different from the computed wday,
If different then set the wday which we computed using
date/month/year values.
Document Referred:
http://ww1.microchip.com/downloads/en/DeviceDoc/20002266F.pdf
Fixes: 1d1945d261 "drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips"
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This flag is a no-op now (see commit 47b0eeb3dc "clk: Deprecate
CLK_IS_ROOT", 2016-02-02) so remove it.
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
If a previously-set alarm was disabled and then triggered, it may still
be pending when a new alarm is configured.
Then, if the alarm is enabled before the pending alarm is cleared, then
an interrupt is immediately raised.
Unfortunately, when the alarm is cleared and enabled during the same I²C
block write, the chip (at least the DS1339 I have) considers that the
alarm is enabled before it is cleared, and raises an interrupt.
This patch ensures that the pending alarm is cleared before the alarm is
enabled.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The i2c_smbus_read_i2c_block_data function returns 0 on success, not the
number of bytes written.
Hence, when there are 32 bytes or less to send, the
ds1307_native_smbus_write_block_data function returns 0 on success,
while it returns the number of bytes when there are more than 32.
The ds1307_write_block_data always returns the number of bytes on
success.
Signed-off-by: Nicolas Boullis <nboullis@debian.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With commit 8bc2a40730 ("rtc: ds1307: add support for the
DT property 'wakeup-source'") we lost the ability for rtc irq
functionality for devices that are actually hooked on a real IRQ
line and have capability to wakeup as well. This is not an expected
behavior. So, instead of just not requesting IRQ, skip the IRQ
requirement only if interrupts are not defined for the device.
Fixes: 8bc2a40730 ("rtc: ds1307: add support for the DT property 'wakeup-source'")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Michael Lange <linuxstuff@milaw.biz>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
while retrieving temperature from ds3231, the result may be overflow
since s16 is too small for a multiplication with 250.
ie. if temp_buf[0] == 0x2d, the result (s16 temp) will be negative.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Michael Tatarinov <kukabu@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has programmable square-wave output signal.
This enables to use this feature as a clock provider of
common clock framework.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DS3231 has the temperature registers with a resolution of 0.25
degree celsius. This enables to get the value through hwmon.
# cat /sys/class/i2c-adapter/i2c-2/2-0068/hwmon/hwmon0/temp1_input
21000
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
For RTC chips with no IRQ directly connected to the SoC, the RTC chip
can be forced as a wakeup source by stating that explicitly in
the device's .dts file using the "wakeup-source" boolean property.
This will guarantee the 'wakealarm' sysfs entry is available on the
device, if supported by the RTC.
With these changes to the driver rtc-ds1307 and the necessary entries
in the .dts file, I get an working ds1337 RTC on the Witty Pi extension
board by UUGear for the Raspberry Pi.
An example for the entry in the .dts file:
rtc: ds1337@68 {
compatible = "dallas,ds1337";
reg = <0x68>;
wakeup-source;
If the "wakeup-source" property is set, do not request an IRQ.
Set also UIE mode to unsupported, to get a working 'hwclock' binary.
Signed-off-by: Michael Lange <linuxstuff@milaw.biz>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This makes the generated code slightly smaller.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With the actual code, read_alarm() always returns -EINVAL when called
during the RTC device registration. This prevents from retrieving an
already configured alarm in hardware.
This patch fixes the issue by moving the HAS_ALARM bit configuration
(if supported by the hardware) above the rtc_device_register() call.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since commit 3fffd12839 ("i2c: allow specifying
separate wakeup interrupt in device tree") we have
automatic wakeup irq support for i2c devices. That
commit missed the fact that rtc-1307 had its own
wakeup irq handling and ended up introducing a
kernel splat for at least Beagle x15 boards.
Fix that by reverting original commit _and_ passing
correct interrupt names on DTS so i2c-core can
choose correct IRQ as wakeup.
Now that we have automatic wakeirq support, we can
revert the original commit which did it manually.
Fixes the following warning:
[ 10.346582] WARNING: CPU: 1 PID: 263 at linux/drivers/base/power/wakeirq.c:43 dev_pm_attach_wake_irq+0xbc/0xd4()
[ 10.359244] rtc-ds1307 2-006f: wake irq already initialized
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
mcp794xx alarm registers must be written in BCD format. However, the
alarm programming logic neglected this by adding one to the value
after bin2bcd conversion has been already done, writing bad values
to month register in case the alarm being set is in October. In this
case, the alarm month value becomes 0x0a instead of the expected 0x10.
Fix by moving the +1 addition within the bin2bcd call also.
Fixes: 1d1945d261 ("drivers/rtc/rtc-ds1307.c: add alarm support for mcp7941x chips")
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The change removes redundant sysfs binary file boundary checks, since
this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
With the recent pinctrl-single changes, SoCs such as Texas
Instrument's OMAP processors can treat wake-up events from deeper idle
states as interrupts.
Let's add support for the optional second interrupt for wake-up using
the generic wakeirq support added in commit 4990d4fe32 ("PM /
Wakeirq: Add automated device wake IRQ handling")
Finally, to pass the wake-up interrupt in the dts file,
interrupts-extended property needs to be passed.
This is similar in approach to commit 2a0b965cfb ("serial: omap: Add
support for optional wake-up") + ee83bd3b64 ("serial: omap: Switch
wake-up interrupt to generic wakeirq")
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
It is always a good practice to keep the #includes sorted
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Since we are not doing anything fancy in remove function that requires
us to sequence IRQ free operation, we might as well switch over to devm_
equivalent of managed IRQ allocation and remove the explicit free_irq
since it'd be done automatically at remove.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The driver currently emulates the concept of threaded IRQ using a
workqueue, which it really does not need to. Instead, switch over to
threaded_irq handlers which is meant precisely for the same purpose.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Alarm interrupt enable register is at offset 0x7, while the time
registers for the alarm follow that. When we program Alarm interrupt
enable prior to programming the time, it is possible that previous
time value could be close or match at the time of alarm enable
resulting in interrupt trigger which is unexpected (and does not match
the time we expect it to trigger).
To prevent this scenario from occuring, program the ALM0_EN bit only
after the alarm time is appropriately programmed.
Ofcourse, I2C programming is non-atomic, so there are loopholes where
the interrupt wont trigger if the time requested is in the past at
the time of programming the ALM0_EN bit. However, we will not have
unexpected interrupts while the time is programmed after the interrupt
are enabled.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
MCP7940x is same RTC as MCP7941x. The difference is that MCP7941x chips
contain additional EEPROM on a different i2c address.
DS1307 driver already supports MCP7941x, so just add a new i2c device id
and rename functions and defines accordingly.
Signed-off-by: Tomas Novotny <tomas@novotny.cz>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some DS13XX devices have "trickle chargers". Introduce a device tree
binding for specifying the trickle charger configuration for ds1339.
Only ds1339 dt binding is supported because this is the only chip I have.
I _assume_ the code would have worked on other allready supported chips.
However I cannot check the resistor values for the other chips or test
them. For other chips the driver code works as earlier Eg. it does not
check the dt bindings at all
Signed-off-by: Matti Vaittinen <matti.vaittinen@nsn.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pavel Machek <pavel@denx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add alarm support for the Microchip RTC devices MCP794xx. Note that two
programmable alarms are provided by the chip but only one is used by the
driver.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In order to allow the creation of the sysfs attribute wakealarm, this
patch moves the device_set_wakeup_capable() call above the RTC device
registration.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The variable want_irq is only assigned the values true and false.
Change its type to bool.
The simplified semantic patch that find this problem is as
follows (http://coccinelle.lip6.fr/):
@exists@
type T;
identifier b;
@@
- T
+ bool
b = ...;
... when any
b = \(true\|false\)
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change to make
the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'client->irq' was not released on error. Fix it.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use devm_*() functions to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current usage of commas instead of semicolons is not wrong, but
affects the readability of the code.
Also, the code would break, if someone puts something between those two
assignments.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dev_dbg() is preferred to pr_debug().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-ds1307 driver does not properly handle block operations bigger
than 32 bytes in either of the two modes supported (SMbus native, or
emulated if not supported by the SMbus platform driver).
It also does not properly handle userland-supplied input (block
operation length) through sysfs and may suffer a type of buffer overrun.
The driver has been modified with proper input validation, buffer sizes,
and now splits block transfers bigger than 32 bytes into separate
transfers.
Explanation : Buffer size allocated is I2C_SMBUS_BLOCK_MAX which equals
to 32 as per the SMbus spec. Reads and write may be up to 56 bytes (to
the NVRAM). This patch allocated a 255 byte buffer, the maximum
allowable (address is an u8). It's not only a buffer problem, SMbus
only supports up to 32 bytes transfer at once, so it's needed to split
bigger transfers.
Patch successfully tested on 3.2.27; cleanly applies on 3.7-rc4.
[akpm@linux-foundation.org: rework code to avoid 80-column overflows]
Signed-off-by: Bertrand Achard <ba@cykian.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mike Frysinger <vapier.adi@gmail.com>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some DS13XX devices have "trickle chargers". Its configuration register
is at different locations, the setup is the same, though. Since the
configuration is board specific, introduce a platform_data to this driver.
Tested with a DS1339 on a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ds1307 was kzalloced, so no need to zero members of the struct.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add struct bin_attribute initialization to fix the following bug:
rtc-ds1307 3-0068: rtc core: registered ds1307 as rtc0
BUG: key cfb14fcc not in .data!
------------[ cut here ]------------
WARNING: at kernel/lockdep.c:2986 sysfs_add_file_mode+0x84/0xdc()
Modules linked in:
[<c0018d94>] (unwind_backtrace+0x0/0xf8) from [<c0031f7c>] (warn_slowpath_common+0x4c/0x64)
[<c0031f7c>] (warn_slowpath_common+0x4c/0x64) from [<c0031fb0>] (warn_slowpath_null+0x1c/0x24)
[<c0031fb0>] (warn_slowpath_null+0x1c/0x24) from [<c012f7ac>] (sysfs_add_file_mode+0x84/0xdc)
[<c012f7ac>] (sysfs_add_file_mode+0x84/0xdc) from [<c04b11e4>] (ds1307_probe+0x5e4/0x6ac)
[<c04b11e4>] (ds1307_probe+0x5e4/0x6ac) from [<c036e600>] (i2c_device_probe+0xdc/0x108)
[<c036e600>] (i2c_device_probe+0xdc/0x108) from [<c02cdf84>] (driver_probe_device+0x90/0x210)
[<c02cdf84>] (driver_probe_device+0x90/0x210) from [<c02ce198>] (__driver_attach+0x94/0x98)
[<c02ce198>] (__driver_attach+0x94/0x98) from [<c02cc824>] (bus_for_each_dev+0x50/0x7c)
[<c02cc824>] (bus_for_each_dev+0x50/0x7c) from [<c02cd780>] (bus_add_driver+0x184/0x244)
[<c02cd780>] (bus_add_driver+0x184/0x244) from [<c02ce43c>] (driver_register+0x78/0x12c)
[<c02ce43c>] (driver_register+0x78/0x12c) from [<c03701ac>] (i2c_register_driver+0x2c/0xb4)
[<c03701ac>] (i2c_register_driver+0x2c/0xb4) from [<c0008798>] (do_one_initcall+0x34/0x178)
[<c0008798>] (do_one_initcall+0x34/0x178) from [<c0691860>] (kernel_init+0xdc/0x194)
[<c0691860>] (kernel_init+0xdc/0x194) from [<c0013cf0>] (kernel_thread_exit+0x0/0x8)
Since commit 6992f53349 ("sysfs: Use one lockdep class per sysfs
attribute") this initialization is required.
Reported-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Generalise NVRAM to support RAM with other size and offset, such as the
64 bytes of SRAM on the mcp7941x.
[rdunlap@xenotime.net: fix printk format warning]
Signed-off-by: Austin Boyle <Austin.Boyle@aviatnet.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do some cleanup of the comment sections as well as correct some
formatting issues reported by checkpatch.pl.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No need to have two seperate if-blocks for setting up the irq.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Tested-by: David Anders <danders.dev@gmail.com>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The chip_desc table is suboptimal. Currently it requires an entry for
every new chip type, even if it is empty. This has already been
forgotten for the ds1388. Refactor the code, so new entries are only
needed, when they chip type really needs a (non-empty) description.
Also make the table visually more appealing.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Austin Boyle <Austin.Boyle@aviatnet.com>
Cc: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add initial support for the microchip mcp7941x series of real time clocks.
The mcp7941x series is generally compatible with the ds1307 and ds1337 rtc
devices from dallas semiconductor. minor differences include a backup
battery enable bit, and the polarity of the oscillator enable bit.
Signed-off-by: David Anders <danders.dev@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PT7C4338 chip is being manufactured by Pericom Technology Inc. It is a
serial real-time clock which provides:
1) Low-power clock/calendar.
2) Programmable square-wave output.
It has 56 bytes of nonvolatile RAM. Its register set is same as that of
rtc device: DS1307.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some rtc drivers use the ioctl method instead of the alarm_irq_enable
method for enabling alarm interupts. With the new virtualized RTC
rework, its important for drivers to use the alarm_irq_enable instead.
This patch converts the drivers that use the AIE ioctl method to
use the alarm_irq_enable method. Other ioctl cmds are left untouched.
I have not been able to test or even compile most of these drivers.
Any help to make sure this change is correct would be appreciated!
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Reported-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Tested-by: Marcelo Roberto Jimenez <mroberto@cpti.cetuc.puc-rio.br>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The ds1307 driver misreads the ds1388 registers when checking for 12 or 24
hour mode. Instead of checking the hour register it reads the minute
register. Therefore the driver thinks minutes >= 40 has the 12HR bit set
and resets the minute register by zeroing the high bits. This results in
minutes are reset to 0-9, jumping back in time 40 or 50 minutes. The time
jump is also written back to the RTC.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows bin_attr->read,write,mmap callbacks to check file specific data
(such as inode owner) as part of any privilege validation.
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
RTC core won't allow wakeup alarms to be set if RTC devices' parent (i.e.
i2c_client or spi_device) isn't wakeup capable.
For I2C devices there is I2C_CLIENT_WAKE flag exists that we can pass via
board info, and if set, I2C core will initialize wakeup capability. For
SPI devices there is no such flag at all.
I believe that it's not platform code responsibility to allow or disallow
wakeups, instead, drivers themselves should set the capability if a device
can trigger wakeups.
That's what drivers/base/power/sysfs.c says:
* It is the responsibility of device drivers to enable (or disable)
* wakeup signaling as part of changing device power states, respecting
* the policy choices provided through the driver model.
I2C and SPI RTC devices send wakeup events via interrupt lines, so we
should set the wakeup capability if IRQ is routed.
Ideally we should also check irq for wakeup capability before setting
device's capability, i.e.
if (can_irq_wake(irq))
device_set_wakeup_capable(&client->dev, 1);
But there is no can_irq_wake() call exist, and it is not that trivial to
implement it for all interrupts controllers and complex/cascaded setups.
drivers/base/power/sysfs.c also covers these cases:
* Devices may not be able to generate wakeup events from all power
* states. Also, the events may be ignored in some configurations;
* for example, they might need help from other devices that aren't
* active
So there is no guarantee that wakeup will actually work, and so I think
there is no point in being pedantic wrt checking IRQ wakeup capability.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible to have RTC irq shared with other device (e.g.
mpc8349e-mitx board shares ds1339 irq with phy one). Handle this in
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code is not executed before ds1307->rtc has been successfully
initialized to the result of calling rtc_device_register. Thus the test
that ds1307->rtc is not NULL is always true.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@match exists@
expression x, E;
statement S1, S2;
@@
x = rtc_device_register(...)
... when != x = E
(
* if (x == NULL || ...) S1 else S2
|
* if (x == NULL && ...) S1 else S2
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc_update_irq() might be called with irqs enabled, if a interrupt
handler was registered without IRQF_DISABLED. Use
spin_lock_irqsave/spin_unlock_irqrestore instead of spin_lock/spin_unlock.
Also update kerneldoc and drivers which do extra work to follow the
current interface spec, as suggestted by David Brownell.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add ds3231 variant. For that, the BBSQI bit position was changed from a
simple define into a lookup-array as it differs. This also removes
writing to an unused bit in case of the ds1337.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the EPSON RX8025 RTC. The date/time registers of this
chip are compatible with the DS1307.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the rtc-ds1307 driver to work with SMBus controllers like nforce2
that do not support i2c block transfers.
Signed-off-by: Ed Swierk <eswierk@aristanetworks.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: BARRE Sebastien <sbarre@sdelcc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove RTC register value checks from the rtc-ds1307 probe() function.
They were left over from the legacy style I2C driver, which had to defend
against finding a non-RTC chip when the driver was probed.
Also fix a minor glitch in the alarm support: DS1307 chips don't have
alarms, so name those methods after one of the chips which actually *do*
have alarms (DS1337).
Signed-off-by: Jüri Reitel <juri.reitel@liewenthal.ee>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sebastien Barre <sbarre@sdelcc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change i2c access functions to SMBus access functions in order to use the
ds1307 with SMBus adapter.
Signed-off-by: Sebastien Barre <sbarre@sdelcc.com>
Acked-by: David Brownell <david-b@pacbell.net>
Tested-by: David Brownell <david-b@pacbell.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Rodolfo Giometti <giometti@enneenne.com>
Tested-by: Sebastien Barre <sbarre@sdelcc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tejun's commit 7b595756ec made sysfs
attribute->owner unnecessary. But the field was left in the structure to
ease the merge. It's been over a year since that change and it is now
time to start killing attribute->owner along with its users - one arch at
a time!
This patch is attempt #1 to get rid of attribute->owner only for
CONFIG_X86_64 or CONFIG_X86_32 . We will deal with other arches later on
as and when possible - avr32 will be the next since that is something I
can test. Compile (make allyesconfig / make allmodconfig / custom config)
and boot tested.
akpm: the idea is that we put the declaration of sttribute.owner inside
`#ifndef CONFIG_X86'. But that proved to be too ambitious for now because
new usages kept on turning up in subsystem trees.
[akpm: remove the ifdef for now]
Signed-off-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change drivers/rtc/ to use the new bcd2bin/bin2bcd functions instead of
the obsolete BCD_TO_BIN/BIN_TO_BCD/BCD2BIN/BIN2BCD macros.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the ds1307 driver with alarm support for ds1337/ds1339. This uses
the first alarm (there are two), and matches on seconds, minutes, hours,
and day-of-month. Tested on ds1339.
[dbrownell@users.sourceforge.net: add comments; fixup style, valid irq
checks, debug dumps; lock; more careful IRQ shutdown; switch BCD2BIN to
bcd2bin (and vice versa); ENOTTY not EINVAL.]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
Update most new-style i2c drivers to use standard module aliasing
instead of the old driver_name/type driver matching scheme. I've
left the video drivers apart (except for SoC camera drivers) as
they're a bit more diffcult to deal with, they'll have their own
patch later.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Jochen Friedrich <jochen@scram.de>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
For DS140, clear the oscillator fault flag as needed.
Signed-off-by: Frederic RODO <f.rodo@til-technologies.fr>
[ And remove some "sparse" warnings. ]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Export the NVRAM on DS1307 and DS1338 chips, like several of the
other drivers do for such combination RTC-and-NVRAM chips.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo turned up by a Coverity check: referring to the wrong register,
which could cause problems with DS1338 RTCs whose oscillators halted.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert the rtc-ds1307 driver into a "new style" driver.
Also improve probe() checks: be more correct about switching out of
AM/PM mode, and issue a (debug) diagnostic when failing due to bogus
register values.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Victor <andrew@sanpeople.com>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@gate.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we find a ds1337 or ds1339 with the oscillator powered off, turn it
on. If the oscillator fault flag was set, clear it and warn that the clock
needs to be set.
David Brownell: Bugfixes; provide corresponding update for ds1338, and the
core of the fix for ds1340. Use a common warning message ("SET TIME!")
whenever the clock needs to be set after oscillator fault (or oscillator
enable, if fault is not a separate status).
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This updates the rtc-ds1307 driver so that converting it to a "new style"
driver (driver model, not legacy i2c model) will involve fewer changes.
- Use pointer to i2c_client almost everywhere, so that it's easy
to let the i2c core create that object;
- Avoid using i2c_client.adapter, since that field is redundant and
thus may go away (same object as i2c_client.dev.parent).
- Extend type enum to include various RTCs this is expected to
work with, and include register support for them.
It also cleans up the support for multiple chip types, and fixes a
glitch that could appear with an un-initialized RTC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix obvious build breakage revealed by 'make allyesconfig'
in current -git.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Update RTC framework so that drivers can constify their method tables, moving
them from ".data" to ".rodata". Then update the drivers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
