Otherwise we may try to power down multiple times when the using
idle bias off and the driver is removed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
The DCS_DATAPATH_BUSY bit used to monitor the completion of DC servo
operations has been deprecated and with some more recente revisions
may perform incorrectly, especially when only analogue bypass paths
are in use. Switch to using readback from the DC servo command
register instead, which is supported for all devices. Without this
unacceptably long timeouts may be observed in some circumstances.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If we need to offset correct the DC servo then don't use runtime
recalibration since that is likely to introduce further offsets
which will be evident on powerdown.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
More recent Wolfson hubs devices add the ability to read back the DC
servo calibration information from the register used to write offsets,
and later still ones remove the old readback registers. Add support
for the new scheme, and use it for WM8994 device revisions that
support it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the correction wraps around then a substantial offset would be
introduced.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
By default, ACPI resource conflict messages are logged at level
KERN_ERR. This is a rather high level for a message that is more a
warning than an indication of a real kernel error. Also, KERN_ERR level
messages can appear over some boot splash screens, and this message is
not serious enough to warrant such treatment. Thus, the log level has
been reduced to KERN_WARNING.
[lenb changed to KERN_WARNING rather than all the way to KERN_INFO]
Also, cleanup message to use %pR resource printing format.
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Calling kobject_uevent() directly is a layering violation. In
particular, it means we'll miss updating the generic LED trigger.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Disabling CONFIG_ACPI_SYSFS_POWER changes the behaviour of
acpi_battery_update(). It will call acpi_battery_get_info()
even if the battery is not present. I haven't noticed this
causing any problem, but it does look like a bad idea.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Acked-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: Always build the powerpc perf_arch_fetch_caller_regs version
perf: Always build the stub perf_arch_fetch_caller_regs version
perf, probe-finder: Build fix on Debian
perf/scripts: Tuple was set from long in both branches in python_process_event()
perf: Fix 'perf sched record' deadlock
perf, x86: Fix callgraphs of 32-bit processes on 64-bit kernels
perf, x86: Fix AMD hotplug & constraint initialization
x86: Move notify_cpu_starting() callback to a later stage
x86,kgdb: Always initialize the hw breakpoint attribute
perf: Use hot regs with software sched switch/migrate events
perf: Correctly align perf event tracing buffer
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: set_cpus_allowed_ptr(): Don't use rq->migration_thread after unlock
sched: Fix proc_sched_set_task()
In initial design, walk_page_range() was designed just for walking page
table and it didn't require mmap_sem. Now, find_vma() etc.. are used
in walk_page_range() and we need mmap_sem around it.
This patch adds mmap_sem around walk_page_range().
Because /proc/<pid>/pagemap's callback routine use put_user(), we have
to get rid of it to do sane fix.
Changelog: 2010/Apr/2
- fixed start_vaddr and end overflow
Changelog: 2010/Apr/1
- fixed start_vaddr calculation
- removed unnecessary cast.
- removed unnecessary change in smaps.
- use GFP_TEMPORARY instead of GFP_KERNEL
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: San Mehat <san@google.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
[ Fixed kmalloc failure return code as per Matt ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- pcmcia_align() used a "start" variable twice. That's obviously a bad
idea.
- pcmcia_common_resource() needs the current "start" parameter being
passed, instead of res->start.
- pcmcia_common_resource() doesn't use the size and align parameters,
so get rid of those.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the call to snd_card_free in the error handling code at the end of the
function, as in the other error cases.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
snd_card_free(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We actually pass an array of 7 chars not 5.
This silences a smatch warning.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The device needs MSI disablement. Added to the quirk list.
Reported-by: Harald Dunkel <harri@afaics.de>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These just represent the secondary and further heads attached to the
card, and they have different sets of PCI bar registers to map.
So don't try to drive them in the main driver.
Reported-by: Frans van Berckel <fberckel@xs4all.nl>
Tested-by: Frans van Berckel <fberckel@xs4all.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
We provide regs->tstate, regs->tpc, regs->tnpc and
regs->u_regs[UREG_FP].
regs->tstate is necessary for:
user_mode() (via perf_exclude_event())
perf_misc_flags() (via perf_prepare_sample())
regs->tpc is necessary for:
perf_instruction_pointer() (via perf_prepare_sample())
and regs->u_regs[UREG_FP] is necessary for:
perf_callchain() (via perf_prepare_sample())
The regs->tnpc value is provided just to be tidy.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ACPI spec (sec 6.4.3.5 in v4.0) requires that for Address Space Resource
Descriptors, _LEN <= _MAX - _MIN + 1 in all cases, but there are BIOSes that
violate this. We experimentally determined that Windows truncates the
resource so it doesn't extend past _MAX, so let's do the same thing in
Linux.
http://bugzilla.kernel.org/show_bug.cgi?id=15480
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
I have a machine here that's sending 0xD1 notifications on the video
device once every second or so. I have no idea why (it's a prototype,
it may be broken), but sending KEY_UNKNOWN is unhelpful and results in
the console becoming unusable. Let's not report keys unless we have
something useful to say about them.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
pxms are mapped to low node ids to maintain generic kernel use of
functions such as pxm_to_node() that are used to determine device
affinity. Otherwise, there is no pxm-to-node and node-to-pxm matching
rule for x86_64 users of NUMA emulation where a single pxm may be bound
to multiple NUMA nodes.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Previously, we assumed the only Device object immediately below the root
was the \_SB Scope (which the ACPI CA treats as a Device), so we forced
the HID of all such objects to ACPI_BUS_HID ("LNXSYBUS").
However, there are DSDTs that supply root-level Device objects with _HIDs.
This patch makes us pay attention to those _HIDs and only add the synthetic
ACPI_BUS_HID for root-level objects that do not supply their own _HID.
For example, this DSDT: https://bugzilla.kernel.org/show_bug.cgi?id=15605
contains:
Scope (_SB) {
...
}
Device (AMW0) {
Name (_HID, EisaId ("PNP0C14"))
...
}
and we should use "PNP0C14" for the AMW0 device, not "LNXSYBUS".
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Yong Wang <yong.y.wang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Don't terminate the watchdog daemon when fsync() fails because no
watchdog driver actually implements the fsync() syscall.
Signed-off-by: Giel van Schijndel <me@mortis.eu>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use of ioremap() causes build failure on S390.
Restrict the driver to ARM until another architecture comes along
and enables the driver for its own use.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The watchdog_info struct cannot be a const since we dynamically fill
in the firmware version.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
smc91c92_cs:
*cvt_ascii_address returns 0, if success.
*call free_netdev, if we can't find hardware address.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmemmap_populate() attempts to report the used index and total size of
vmemmap_table, but it wrongly shifts the total size so that it is
always shown as 0.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While chasing a bug report involving a OS/2 server, I noticed the server sets
pSMBr->CountHigh to a incorrect value even in case of normal writes. This
results in 'nbytes' being computed wrongly and triggers a kernel BUG at
mm/filemap.c.
void iov_iter_advance(struct iov_iter *i, size_t bytes)
{
BUG_ON(i->count < bytes); <--- BUG here
Why the server is setting 'CountHigh' is not clear but only does so after
writing 64k bytes. Though this looks like the server bug, the client side
crash may not be acceptable.
The workaround is to mask off high 16 bits if the number of bytes written as
returned by the server is greater than the bytes requested by the client as
suggested by Jeff Layton.
CC: Stable <stable@kernel.org>
Reviewed-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
By doing this we always overwrite nbytes value that is being passed on to
CIFSSMBWrite() and need not rely on the callers to initialize. CIFSSMBWrite2 is
doing this already.
CC: Stable <stable@kernel.org>
Reviewed-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Jeff Layton <jlayton@samba.org>
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Now that software events use perf_arch_fetch_caller_regs() too, we
need the powerpc version to be always built.
Fixes the following build error:
(.text+0x3210): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0x3324): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0x33bc): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0x33ec): undefined reference to `perf_arch_fetch_caller_regs'
(.text+0xd4a0): undefined reference to `perf_arch_fetch_caller_regs'
arch/powerpc/kernel/built-in.o:(.text+0xd528): more undefined references to `perf_arch_fetch_caller_regs' follow
make[1]: *** [.tmp_vmlinux1] Error 1
make: *** [sub-make] Error 2
Reported-by: Michael Ellerman <michael@ellerman.id.au>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Now that software events use perf_arch_fetch_caller_regs() too, we
need the stub version to be always built in for archs that don't
implement it.
Fixes the following build error in PARISC:
kernel/built-in.o: In function `perf_event_task_sched_out':
(.text.perf_event_task_sched_out+0x54): undefined reference to `perf_arch_fetch_caller_regs'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
* 'merge' of git://git.secretlab.ca/git/linux-2.6:
powerpc/5200: in lpbfifo, flag DMA irqs as enabled after requesting them
powerpc/fsl: add device tree binding for QE firmware
of/flattree: Fix unhandled OF_DT_NOP tag when unflattening the device tree
The missing initialization of the nb_cntl.strap_msi_enable does not
seem to be the only problem that prevents MSI, so that quirk is not
sufficient to enable MSI on all machines. To be safe, disable MSI
unconditionally for the internal graphics and HDMI audio on these
chipsets.
[rjw: Added the PCI_VENDOR_ID_AI quirk.]
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'kgdb-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: Turn off tracing while in the debugger
kgdb: use atomic_inc and atomic_dec instead of atomic_set
kgdb: eliminate kgdb_wait(), all cpus enter the same way
kgdbts,sh: Add in breakpoint pc offset for superh
kgdb: have ebin2mem call probe_kernel_write once
* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Freezer: Fix buggy resume test for tasks frozen with cgroup freezer
Freezer: Only show the state of tasks refusing to freeze
release_one_tty(tty) can be called when tty still has a reference
to pgrp/session. In this case we leak the pid.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-and-tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building chokes with:
In file included from /usr/include/gelf.h:53,
from /usr/include/elfutils/libdw.h:53,
from util/probe-finder.h:61,
from util/probe-finder.c:39:
/usr/include/libelf.h:98: error: expected specifier-qualifier-list before 'off64_t'
[...]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Masami Hiramatsu <mhiramat@redhat.com>
LKML-Reference: <20100329164755.GA16034@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The kernel debugger should turn off kernel tracing any time the
debugger is active and restore it on resume.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Memory barriers should be used for the kgdb cpu synchronization. The
atomic_set() does not imply a memory barrier.
Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
This is a kgdb architectural change to have all the cpus (master or
slave) enter the same function.
A cpu that hits an exception (wants to be the master cpu) will call
kgdb_handle_exception() from the trap handler and then invoke a
kgdb_roundup_cpu() to synchronize the other cpus and bring them into
the kgdb_handle_exception() as well.
A slave cpu will enter kgdb_handle_exception() from the
kgdb_nmicallback() and set the exception state to note that the
processor is a slave.
Previously the salve cpu would have called kgdb_wait(). This change
allows the debug core to change cpus without resuming the system in
order to inspect arch specific cpu information.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The kgdb test suite mimics the behavior of gdb. For the sh
architecture the pc must be decremented by 2 for software breakpoint.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Rather than call probe_kernel_write() one byte at a time, process the
whole buffer locally and pass the entire result in one go. This way,
architectures that need to do special handling based on the length can
do so, or we only end up calling memcpy() once.
[sonic.zhang@analog.com: Reported original problem and preliminary patch]
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
